Search Documents

WHEN pouring concrete it frequently happens that space prohibits the placing of a mixer at the point, or points, where the concrete is to be used. Usually in such cases recourse is had to some form of pressure chamber, or concrete gun, to blow the mix by compressed air from the mixer to the point of pouring. Recently such a case arose at one of the western mines. The experience obtained there may be of benefit to others, not expert in the means of transporting mixed concrete, when they run up against similar situations. The first stage in pouring in this instance was a vertical drop of 100 ft. from the mixer on one level to the point where horizontal travel began on a lower level. Standard 6-in. pipe with flange joints was used, hung in the shaft space available. A standard 45" bend near the bottom directed the mix, with free discharge, into an air chamber for the horizontal stage of travel. With an air chamber at the mixer and pressure applied to the falling mix in the vertical section, jamming frequently occurred at the turn and the pipe would have to be taken apart for freeing. To obviate this difficulty the mix was poured slowly without the addition of air pressure, when it was found that the mix got through much better.

Jan 1, 1929

By P. E. Phillips

INTRODUCTION Rocky Mountain Energy is the mining subsidiary of the Union Pacific Corporation, and has been active m uranium exploration since 1966. Since 1970, RME's uranium activities have been funded 50% by Mono Power, the fuels supply division of Southern California Edision. RME and Mono recognized the need for development of new methods for recovering low grade uranium deposits, and contacted Halliburton Services in regard to in situ leaching, because of Halliburton oil industry experience. As a result, a joint venture between the three parties was formed in 1974. BEAR CREEK The first ISL test was at the Bear Creek deposit in the Powder River Basin of Wyoming, about 60 miles north of Douglas. The mineralized sand is the tertiary Wasatch formation, which is an arkosic sandstone. The sand typically contains about 10% clay. The predominant clay being montmorillonite with some kaolin and illite. The roll front type trends occur along the flanks of old stream channels. This deposit was being considered for exploitation as an open pit mine. Routine amenability testing indicated it was quite amenable to a conventional acid leach, consuming about 50 lbs. of sulfuric acid per ton of ore in an agitation leach, while recovering more than 95% of the uranium. Hydrology testing indicated a permeability of about 1 darcy. The groundwater has a pH of about 8. 0 and TDS of about 1200. Test Facility The Bear Creek test was a summer-only operation, with no effort towards weather-proofing. Uranium was removed from the recovered leach solution by fixed bed ion-exchange columns. Loaded resin was eluted with strong sulfuric acid. The recovery plant was designed for simplicity of operation, with little concern for the grade or form of the yellowcake product. The plant was constructed of PVC piping and valves, fiberglass reinforced tanks, and stainless steel pumps. All waste streams were directed toward a lined evaporation pond. Wellfield The test pattern was a 30 foot radius 5 spot, with wells fully penetrating the 30 foot ore sand to a total depth of about 165 feet. The injection wells were three-inch PVC with slotted casing, while the producer was eight-inch I. D. , with a stainless steel screen. The eight-inch well was necessary in order to accommodate a six-inch stainless steel pump. Wells were cemented using cement baskets, at the top of the sand, to contain a latex acid resistant cement. Leach Conditions The lixiviant generally contained from five to seven gpl sulfuric acid, and about 0. 5 gpl hydrogen peroxide. The pH was generally 1.4 and EMF was usually -550 millivolts. Injection rates were rather variable from well to well, with a total injection rate between 12 and 25 GPM. Production rate was set at 25 GPM, since the production pump could not be throttled more than that. Approximately two pore volumes of solution were injected during the three-month test. Leach Results Injectivity was quite variable, but was generally rather poor, because of poor completion techniques. The problem stemmed from injecting before the injection wells had been completely cleaned of drilling mud. Pregnant solutions averaged about 50 ppm U308, with groundwater dilution varying from 10 to 50%, depending on the injection rate. Injectivity did decline with time, probably as a result of contamination of the well faces. A total of 1000 lbs U308 had been recovered when the test was shut down. This probably represented about 10% of the mineral under leach.

Jan 1, 1979

By R. H. Frazier, F. W. Boulger

THE performance of welded structures is closely associated with the ductile-to-brittle transition temperature of the steel from which they are made. A low transition temperature is desirable because it indicates that the steel is less likely to fail suddenly at low ambient temperatures. Structures such as bridges, ships, storage tanks, and pipelines are usually made from hot rolled semikilled steel. Changes in rolling practice or chemical composition appear to be the most practical methods for improving the toughness of such materials. This results from the fact that production is likely to be seriously curtailed if improvements were obtained by recourse to heat treatment or complete deoxidation. This paper discusses the effect of variations in carbon and manganese contents on the properties of semikilled steels. The transition temperature, a property to which considerable importance is attached, varies with specimen configuration, testing method, and criterion of performance. Both the Navy tear test' and the keyhole Charpy test were used in the investigation. According to the terms used by Vanderbeck and Gensamer,V he tear test was used to measure a fracture transition and the Charpy test to measure a ductility transition. In either case the specimens absorb considerably less breaking energy in tests below the transition temperature than in tests above the transition temperature. Decreasing the testing temperature of notched-bar specimens seems to be equivalent in its effect to increasing the severity of loading on fabricated structures. Therefore, structures built from steels exhibiting lower transition temperatures in laboratory tests are expected to be less susceptible to sudden brittle fractures in service. Consequently, changes in composition which lowered the transition temperature of the experimental steels were judged desirable. Materials and Methods The steels for this study were made in a laboratory induction furnace and rolled to 3/4 in. plate, using a finishing temperature of 1850°F. Precautions taken to insure reproducible melting and testing practices are discussed in detail elsewhere.' All tests were made on hot rolled steels. The analyses of the experimental steels are given in Table I. The list includes steels with manganese contents ranging from 0.21 to 1.46 pct, at each of five carbon levels. The phosphorus, silicon, sulphur, and nitrogen contents of the steels are reasonably constant. The tensile and notched-bar properties of the experimental steels are presented in Table 11. Both upper and lower yield points are listed, and all values are averages for duplicate specimens. Transition temperatures based on three criteria are given. The keyhole Charpy transition temperatures are the temperatures at which the energy-temperature curves based on averages of four specimens cross the 20 and 12 ft-lb levels. Both definitions of Charpy transition temperatures have been used by other investigators. Charpy tests were made at intervals of 10°F, using a pendulum with an available striking energy of 220 ft-lb and a velocity of 18.1 ft per sec. The specimens were oriented parallel to the rolling direction and notched normal to the surface of the plates. The tear test transition temperatures are based on the usual' criterion of the highest temperature at which at least one of four specimens exhibits brittle behavior. The dimensions of the tear test specimens are shown in Fig. 1. The specimen is loaded eccentrically in tension, with pin and shackle fixtures, through the large holes while submerged in a liquid bath at the proper temperature. A specimen developing a fracture area with less than 50 pct shear or ductile texture is classed as brittle. Tear tests were made at intervals of 10°F.

Jan 1, 1955

* Kennecott Copper Corp. gets Charles R. Cox as president on Jan. 1. Mr. Cox is resigning his position as president of Carnegie-Illinois to take the new post with Kennecott, left vacant by the death of Mr. Stannard in September. •The ECA signed a contract in December to advance X3,600,000 to Newmont Mining Corp. to aid development of lead and zinc mines in French Morocco. The funds are to be repaid in lead and zinc for the United States' stockpile over a period of seven years. The mines are owned by the Societe des Mines de Zellidja, with which organization Newmont is associated. • Under the direction of John M. Brooks, Jr., general manager, the Matahambra mine in Cuba, will probably produce sufficient tonnage to make 4 million lb of copper per month during 1950. The grade is presently running between 7 and 10 pet. •S. H. Ash reports that the fatality rate per million-man-hr for the anthracite industry for 1949, through November, is 0.78. This is 15 pct better than that achieved during 1948, which was the lowest fatal injury rate in coal mining history. The first full year on record without a major disaster was recorded in 1949 (p. 34). •The Atomic Energy Commission has authorized the production of 200 lb of uranium metal for use under AEC license in non-Commission research projects. •A national survey of projected 1950 purchases of new machine tools, machine tool accessories, materials handling equipment, etc., just completed by the American Society of Tool Engineers reveals that, of the companies reporting, 80 pct state that they plan to buy either more equipment or the same amount as in 1948. • Armour Research Foundation is conducting investigations for the use of clay and shale deposits to make lightweight aggregates. The material is heated until it expands and forms material suitable for mixing with cement which it is hoped will be lighter, stronger, have better insulating qualities and will lower the cost of concrete. •In the first six months of 1949 the bituminous coal miners' average hourly earnings were $1.94 -as compared with X1.392_ national average for all manufacturing. Average annual earnings of full-time employees in the bituminous coal mines in 1948 were $3387 as compared with $2809 for all industry. •LaSalle Business Bulletin reports: "year ends on a rising trend in industry and trade ... nearly record-breaking demand from almost all sources keeps business high... most indicators but little below postwar peak... forces keeping activity high arestill powerful--changes in general business conditions likely to be slow and moderate." •Office of Internal Trade of the Commerce Department requests that technical data significant to the national security which is to be sent outside of the United States be submitted to it for an official opinion on the desirability of transmitting such information. This voluntary compliance program is part of our national security control. • Blast furnace slag reduced to 12 to 16 mesh is being used for sanding track at the Mont Coal mines of Armco. The slag replaces silica sand which caused silicosis. It has proved so effective and cheap that tests are being made to use the slag for rock dusting.

Jan 1, 1950

By H. E. Stauss, E. I. Salkovitz, F. W. von Batchelder

EXISTING information regarding the structure of a spherulite in nodular cast iron is based on optical studies. According to these data, a nodule consists of an aggregate of graphite crystallites radiating from the center, with the closely packed basal planes at right angles to the radii. The c axes lie along the radii. This view faces some uncertainty in the fact that the c axis does not represent the accepted direction of fastest growth in graphite. To supplement the optical information, X-ray studies have now been made. The principle used was to screen the nodule in greater part from the X-ray beam and expose only a minor cap. As successively larger portions of the nodule were introduced into the X-ray beam, any differences in the X-ray patterns could be observed. Such photographs have been taken with chromium radiation and a Laue camera. The graphite nodule itself, about 0.010 to 0.025 in. in diam, was mounted with vaseline on a micrometer screw for control of the linear motion. The nodule rotated about 45" each time that it was translated linearly. The nodules were obtained from magnesium-treated hypereutectic iron by electrolytic solution of the iron in hydrochloric acid. In Fig. la is shown the pattern of the thinnest cap examined. In Fig. lb is shown the pattern of the same nodule moved 0.003 in. farther into the X-ray beam, and rotated 45" at the same time. Figs, la and lb indicate incomplete circles for graphite (the two outer circles arise from graphite) with the side arcs much weaker than the top and bottom ones. The arcs obtained are themselves not continuous in intensity but vary with maxima of intensity some 15" and 30" apart. The structure of the nodule that would give rise to such a pattern can be explained as follows. Basically the nodule consisted of small crystallites. The discontinuous character of the diffraction rings demonstrates that the nodule was not composed of randomly oriented crystallites. The strong vertical reflections and the weak lateral reflections show that the reflecting planes were roughly normal to the radii. The absence of sharp reflection spots suggests that the nodule did not contain large crystals. The sharpness of the diffraction rings in their radial direction shows that the variations in intensity along the arcs were not the result of line broadening resulting from extremely small crystals. In the diffraction patterns two rings corresponding to graphite were found. The third and inner ring in the figures originated in the vaseline. The graphite rings correspond to the a and ß lines reflected from the basal planes, showing that the radii of the nodules are the [0001] direction normal to the basal planes of graphite. The picture of the structure that is formed is, therefore, one of aggregates of crystallites. Within each aggregate the c axes of the crystallites tend to align themselves in the radial direction of the nodule, although these axes deviate somewhat in direction by a continuous variation of angle. Correspondingly the basal planes of the graphite crystallites are generally normal to the radii. It is a pleasure to acknowledge the assistance of M. C. Bloom and R. P. Dunphy of this laboratory.

Jan 1, 1952

By L. A. Roe, John Jan

Iodine is a soft, lustrous, grayish-black nonmetallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue-violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 25 and 35 million lb per year, of which about 30% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and seawater. According to the US Geological Survey, it is the 47th most abundant element in the earth's crust. The minerals lautarite, Ca (I03)3 (calcium iodate), and dietzeite, Cat (103)2 (CrO4), (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapaca provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in Table 1. Table 2 lists estimated world iodine reserves. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated reserves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. Markets and Prices Iodine and its compounds are generally marketed in the form of: iodine, crude; iodine, resublimed; calcium iodates; calcium iodide; potassium iodide, sodium iodide, and numerous organic compounds. Product Specifications Crude iodine, World market: 99-99.5% 12. Crude iodine, US produced, average: 99.8% 12. Crude iodine, USP XVII Specs: not less than 99.8% percent I2. Resublimed iodine is usually 99.9% and ACS specifications call for not over 0.005% total bromine and 0.020% nonvolatile materials (Anon., 1971). Prices, c.i.f. United States, for iodine have been steadily increasing from $1.18 per lb of crude in 1967 to $6.37-7.27 in January 1981 (Anon., 1981). In 1980 the price of iodine increased by 50%.

Jan 1, 1983

By Henry P. Chandler

Tripoli is the general name for a number of fine-grained, lightweight, friable, minutely porous, forms of decomposed siliceous rock, probably derived from siliceous limestones or calcareous cherts. Tripoli is often confused, both in the trade and technical literature, with tripolite, a diatomaceous earth (diatomite), found in Tripoli, North Africa. A material found near Seneca, Mo., resembling tripolite was incorrectly termed "tripoli." This name has persisted and now has a definite physical and trade meaning. However, tripoli contains no diatoms, is of an entirely different origin, and has chemical and physical properties different from those of tripolite. There are two distinct types of tripoli in the United States; that from the Missouri-Oklahoma field and that from the Southern Illinois field. Commercially the term "tripoli" is applied to the material from the Missouri-Oklahoma field, while the material from the Southern Illinois area is often referred to as "amorphous" or "soft" silica. Material similar to the Missouri-Oklahoma tripoli, but finer grained, occurs in northwestern Arkansas. In its Minerals Yearbook the Federal Bureau of Mines groups statistically under "natural silica abrasives," tripoli from these producing areas and rottenstone from Pennsylvania. The justification for this grouping is the similarity of use. Composition and Physical Properties Commercial tripoli contains 97 to 99 pet SiO2. The remainder is mostly alumina, iron, lime, soda, and potash, some of which may impart desirable physical properties to the material. Variations in the chemical composition of tripoli are not as important as its physical characteristics. The color of tripoli varies from white to cream, brown, rose, and red, the variations from white being the result of iron deposited from percolating surface waters. The commercial varieties of tripoli mined in the Missouri-Oklahoma area are designated as cream and rose. Other physical properties of the tripoli from this area are: Free quartz, less than 0.5 pct; oil absorption, 50.71 to 53.14 pct; water absorption of the crude tripoli, about 38 pct, and of prepared material, about 52 pct; fracture, uneven to conchoidal; specific gravity, 2.15 to 2.62; weight per cubic foot crude, 35 lb, ground, 55 lb; fusion point, 3,225° to 3,300°F; and refractive index, 1.54. Tripoli occupies about 1 cu yd to the short ton in place and about 1.5 cu yd when broken. Packed for shipment, the powdered material occupies about 33 cu ft to the ton. Its value and usefulness depend primarily on a low content of crystalline silica, size of the natural particles, absorption, and color. Some beds in the Missouri-Oklahoma area are of sufficiently compact material that large, fairly strong blocks may be removed. These find a market as filter blocks and have been used for building material. In the Southern Illinois field the color of the material is the important physical property; pure white is preferred. The rottenstone mined in Pennsylvania is of higher density and lower in silica content than the various types of tripoli. Its composition approximates 60 pct silica, 18 pct alumina, 9 pct iron oxide, 8 pct alkalies, with small amounts of lime and magnesia. The material apparently is a ferruginous and siliceous shale, having properties rendering it suitable as an abrasive or as a filter for paint, rubber, and plastics.

Jan 1, 1960

By S. Leber

Pole figures and pole distributions were used for the quantitative detevinination of the preferred orientations in swaged tungsten rods and the effect of subsequent wire drawing on the texture. In the swaged rod, the preferred orientation could best be described as a pseudo (111-112) [110] cylindrical texture. A secondary component was assigned the indices (110) [001]. Further reduction by swaging retained these cylindrical textures. Wire drawing caused lattice rotations about the wire axis, converting the cylindrical texture into a normal fiber texture. The conversion was initiated and proceeded lnost rapidly in the center of the wire. The (110) /001] component was converted into a (110) fiber texture by wire drawing. The effective rotations were about axes contained in the lransverse plane. The preferred orientation associated with tungsten wire usually has been assumed to consist of a (110) fiber texture. This implies rotational randomness around the wire axis. Leber1 has shown that rotation about the wire axis may be restricted resulting in a preferred orientation designated as a cylindrical texture. Specific crystal planes tended to remain aligned parallel to the wire surface. This texture seemed to be the result of the swaging operation used in the intermediate stages of fabrication. Bhandary and cullity2 detected similar textures in swaged iron wires. Peck and Thomas3 suggested that the preferential alignment of crystal planes parallel to the wire surface was the result of tangential flow, characteristic of swaging. Wire drawing, following swaging, twisted the crystals about axes parallel to the wire axis, converting the cylindrical texture into a normal fiber texture.4 In this investigation, quantitative techniques were used to more accurately characterize the cylindrical texture and to study its conversion into a normal fiber texture. PROCEDURE The material investigated was lamp-quality tungsten. Three ingots were rod-rolled and swaged to 112 mils diameter, and were then drawn to 10-mil wire. Samples were obtained after each drawing pass. (110) and (200) pole figures were obtained from samples prepared as shown in Fig. 1. To form the sample shown in Fig. l(a), l-in. lengths of wire were glued side by side to form a l-in. square. The composite was ground and electropolished to form a diametral reference surface. For certain specific tests, samples were prepared as shown in Fig. l(b). This composite was made from 10-mil-thick strips prepared by grinding on parallel longitudinal planes. The polished reference surface in this case was, in essence, the wire surface. The two forms of samples [~igs. l(a) and l(b)] were related by a 90-deg rotation around the wire axis. Because of ease in preparation, most data was obtained from the diametral samples. The X-ray data were obtained using a Siemen's pole-figure goniometer. These data were not corrected for absorption or defocusing effects, since only the angular locations of the intensity maxima were of interest. Regions of the pole figure more than 80 deg from the center were not investigated. Partial monochromatization was achieved by the use of unfiltered copper radiation and a krypton-filled proportional counter. No evidence of spurious white radiation effects5 could be detected. Therefore, more elaborate X-ray techniques were not required. Intensity levels were chosen to show all pertinent details of the orientation distributions. The reference plane for the pole figures was the diametral section. The orthogonal reference directions, shown in Fig. 1, were the wire axis, the radial axis per-

Jan 1, 1965

By Charles W. Chesterman

Perlite is a glassy volcanic rock which will, upon rapid controlled heating, expand or "pop" into a frothy material of low bulk density, valued as a lightweight aggregate. The term perlite also is applied to the expanded product. The chemical composition of perlite ranges from that of rhyolite to that of andesite; the water content ranges from 2 to 5%. Most perlite is pale gray, but some is black, brown, or even green. Inclusions in perlite are common and include phenocrysts of quartz, feldspar, biotite, and hornblende, and miscellaneous rock fragments. Occurrences of perlite are restricted to areas of Tertiary and Quaternary volcanic rocks. Perlite occurs as flows associated with thick accumulations of pyroclastic debris and other flow rocks, as dikes, sills, domes, and as selvages of intrusive bodies of volcanic rock. Individual flows of perlite range in thickness from a few feet to as much as 100 ft and commonly cover several square miles. Dikes and sills of perlite generally are small, but domes generally are substantial in size and may be as much as several miles in diameter. Most perlite deposits are large enough and topographically situated so as to lend themselves to low-cost open pit mining methods. Conventional equipment is employed in the mining of perlite. Although milling procedures may appear to be simple, care is exercised in order to produce a carefully sized product and to minimize the production of excessive quantities of fine materials, which have limited use and are considered as waste. Perlite is processed, or "popped," in one of two basic types of furnaces: horizontal rotary or vertical stationary. Both types of furnaces include product collection and dust control systems. Many commercial deposits of perlite are known to occur throughout the world, and although no exact estimate of reserves is available, there appears to be an adequate supply to meet current and future worldwide requirements. End Uses The uses of expanded perlite are many and varied and are based primarily upon its physical and chemical properties. Because of its (1) low bulk density, which generally ranges between 2 and 20 lb per cu ft; (2) low thermal conductivity "K" factor (Btu per hr per sq ft per OF per in, of thickness), which ranges between 0.267 for loosely packed perlite (bulk density of 4.48 lb per cu ft) to 1.25 for perlite gypsum plaster; (3) high resistance to fire; and (4) low sound transmission, expanded perlite is used to a great advantage as aggregate and insulating material in the construction industry. Early uses of perlite were related exclusively to the construction industry, which now consumes about 60% of the domestic production. The primary use of perlite now is as aggregate in insulation boards. Other uses of perlite in 1971 were as aggregate for plaster, horticultural aggregate, low-temperature insulation (cryogenics), and concrete. Because of its low thermal conductivity ("K" factor), high adsorption of sound, low bulk density, and fire resistance, perlite aggregate plasters hold many advantages over conventional plaster. Perlite aggregate plaster lends itself to machine applications, dries quickly, and has relatively high elasticity which reduces cracking after drying. These same features make perlite useful as aggregate in portland cement concrete and asphalt concrete for construction wherever weight reduction, insulation, and acoustics are of prime importance. Perlite-portland cement concrete offers up to 20 times more thermal insulation than conventional concrete, and because of this it finds wide application in roof decks and floor fill in multistory buildings, in

Jan 1, 1975

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By H. K. Najarian

This paper describes recent development work on the Wheaton-Najarian Vacuum Condenser for Zinc at Josephtown Zinc Smelter, wherein, to dissipate the heat of condensation, the "airlift" action of gases bubbling through the molten zinc in the condenser is utilized to circulate the zinc through an outside "cooling well" and cooling it continuously. AN earlier paper1 gave an account of initial development of the Wheaton-Najarian Vacuum Zinc Condenser at the Josephtown Zinc Smelter of the author's company. This paper is a progress report of further development work over the years directed toward improving the efficiency and increasing the capacity of the condenser. In this type of zinc condenser, zinc vapor with accompanying noncondensable gases from electro-thermic zinc smelting furnaces is passed upwardly through a mass of molten zinc confined in a refractory-lined U-tube. The zinc vapor condenses in the molten zinc and the noncondensable gases are drawn out of the condenser by suction applied over the surface of the molten zinc. The heat of condensation of zinc, amounting roughly to 1000 Btu per lb of zinc condensed, is absorbed by the molten zinc and, in turn, is dissipated continuously to keep the temperature of molten zinc in a range to permit effective condensation. At the time of publication of our first paper, we had at Josephtown Smelter five units of 69-in.-bore metal furnaces and one larger metal furnace having 96-in. bore. Each 69-in. metal furnace had a condenser with 22-ft overall length. The 96-in.-bore furnace had a condenser with overall length of 31 ft. Condensers were of circular cross section, with corrugated steel outer shell and carborundum lining. Diameter of these condensers was 32 in. inside the refractory lining. Molten metal in the con- denser was kept cool by spraying cold water on the outside of the condenser shell. Under good operating conditions, 22-ft condensers produced some 12 tons of metal per day; and the 31-ft condenser, about 22 tons. When the furnaces produced zinc vapor at higher rates, invariably the condenser temperature would rise to levels where excessive blue powder would form and accumulation of accretions in the condenser would be accelerated. We found that, with the system of cooling in use, we had to provide heat-exchange surface of some 150 sq ft to condense 1000 lb of metal per hr with reasonable efficiency. The wall of the condensers was made up of 5/8-in.-thick corrugated-steel shell having next to it several layers of mica and inner refractory lining of special carborundum shapes to fit the corrugation in the steel shell, and having a minimum thickness of about 2 in. Relatively low rate of heat transfer through the thick condenser wall and slow internal circulation of the molten zinc limited the rate of heat exchange between hot metal within the condenser and the cold water flowing over the outer steel shell. The thickness of the condenser wall was about minimum that we considered suitable for continuous operation. As we learned to operate the electrothermic furnaces with higher power input, producing zinc vapor at higher rates, it became apparent that we needed condensers having larger heat-exchange surfaces. Our 96-in.-bore furnace had 6 single-phase power circuits with transformers rated at 500 kva each and normally good for power input of 3000 kw.

Jan 1, 1959

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-' pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.' and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By R. J. Evans

The Combined Metals Reduction Co.'s plant is at Bauer, Utah. It was built primarily to treat ore from the Combined Metals mine at Pioche, Nevada. Shortly after its completion, the company acquired the old Honerine mine, and ores from this mine, as well as custom ores from widely scattered districts, are now being treated at the Bauer plant. Pioche Ore The Pioche ore, which comprises about 50 per cent. of the mill feed, occurs as a replacement of an impure thin-bedded limestone. The lime beddings are separated by thin layers of micaceous shale containing appreciable quantities of sericitc and graphite. The ore is an exeeptionally fine-grained, dense mixture of minerals and gangue, assaying approximately 0.03 oz. gold, 7.2 oz. silver, 7 per cent. lead, 15 per cent. zinc, 16 per cent. iron, 29 per cent. insoluble and 1.5 per cent,. lime. Of the total lead 7 per cent. is in the form of sulfate and carbonate. Approximately 10 per cent,. of the ore consists of chert nodules impregnated with barren pyrite; the nodules average 0.8 mm. in size, and ire extrcmely hard, compared with the other constituents of the ore. Microscopic examination of Pioche ore ground to 80 per cent . minus 150 nicsh shows pyrite, sphalerite and galena still attached. Early Attempts at Ore Dressing Metallurgists, both professional and those working for private companies, have been more or less familiar with the Pioche ore sinee. 1913; in fact, a total of 35 commercial and plant laboratories expenmented with the ore between 1913 and 1921. The work during this period was decidedly negative, it being seemingly impossible to effeet a satisfactory separation of the valuable minerals into marketable products. In 1913, it was recognized that fine grinding-—that is, about minus. : 200 mesh—-was required to liberate the minerals from one another, and from the gangue, but such fine grinding was not considertd practicable at this time.

Jan 1, 1928

By Oliver Bowles

STRIKING new developments in the field of industrial minerals include the employment of lime, salt, coal, and air for the manufacture of stockings, and the substitution of paper for granite and marble in making tombstones. Certain minerals that have heretofore been regarded as valueless except as museum or laboratory specimens, are now being applied commercially. Serpentine, in forms neither fibrous nor ornamental, massive topaz, pinite, and zoisite are examples. For certain other minerals, notably pyrophyllite, bentonite, vermiculite, and sulphur, extension of established uses into new fields has occurred. Substitution takes a toll in many industries, but producers of industrial minerals as a class have gained more than they have lost in recent years. Encouraging progress has been made in developing at long last a suitable substitute for certain of the uses of mica, the only industrial mineral on the strategic list of commodities established by the War. and Navy Munitions Board. Some of the more important developments in process, equipment, and use .that have come

Jan 1, 1940

By Louis D. Huntoon

(New Haven Meeting, February, 1909.) THE Hammond Mining and Metallurgical Laboratory is the gift of Prof. John Hays Hammond to the Sheffield Scientific School of Yale University. Professor Hammond was graduated from this school in the class of 1876, and has always shown great interest in its welfare and progress. In 1903, he offered to build and equip for it a mining and metallurgical laboratory. This offer was gratefully accepted by the trustees; and in October of the same year the architect, W. Gedney Beatty, and the writer were employed to draw up plans for the building, which is the largest of its kind in this country. The Treasurer's report shows the total gift of Professor Hammond, including land, building, and equipment, to have been $128,741.53. This does not include $5,000 given by Professor Hammond to defray incidental expenses. The detailed cost of the machinery and installation, included in the above sum, is as follows: Machinery, $9,846.00 Pipe and fittings, 925.05 Hangers, shafting, pulleys, belts, etc., . 357.83 Steel-work, tanks, launders, etc., . 272.19 Screens for sizing ore, 411.37 Lumber, 1,896.36 General Supplies Hardware, . $135.96 Tools, 263.66 Paints, . 04.63 Electric and incidental, . 439.57 - 1,043.82 Machine-shop material, 259.44 Labor, 722.29 - 981.73

Mar 1, 1909

By J. F. Myers, F. M. Lewis

C. G. McLACHLAN*-I have read this paper with considerable interest and wish to congratulate the authors on the care with which they carried out their experiments and for the detailed sizing data they have presented. 011 the other hand I do not feel that these data establish their contention that "with other factors the same, the work accomplished in a fine crushing rod mill is directly proportional to the rotating speed." My reason for making this statement is that their conclusion is based on the percentage of minus 65 mesh material produced at each of the speeds at which their tests were run. The rod mill is, however, not a fine grinding machine and therefore figures based on minus 65 mesh production are figures outside the range at which it operates to best advantage. Further, if rod mill performance is to be judged on the production of such material it should have been established that a rod mill will produce it as effectively as a ball mill. To check this last point I have gone over some of the rod and ball mill grind-ing figures for our Waite-Atnulet operation and find that the ball mill at that property produces more minus 65 mesh material per horsepower than the rod mill. Moreover, this comparison is even more favorable to the ball mill if it is limited to minus 100 mesh production. It therefore seems to me that the most satisfactory basis on which to try to com-pare the performance of the rod mill in the present case is by taking a weighted average of all the new surface produced per horsepower. W. H. Coghill3 has published data which can be applied to the sizing figures presented by the authors, and if this is done the units of new surface per horsepower produced in the Tennessee tests are as follows: Admittedly the increment of increase in new surface per horsepower shown in the foregoing figures is not great, but its trend is nevertheless definitely in favor of slower speed operation, for the conditions under which these particular tests were run. I also feel that some information regarding liner contour should have been given as I think it will be found that a mill which is equipped with liners which lift the rod load can be run at a slower speed than a mill in which the liners are comparatively smooth. J. F. MYERS and F. M. LEWIS (authors' reply)—The position taken by Mr. McLachlan is to be respected even though we are all aware of the faults of surface considerations. As he points out. the increment of increase is very small. It is so small in fact that for all practical purposes it does not conflict with the conclusions of the paper. The authors appreciate Mr. McLachlan's comprehensive study of the data.

Jan 1, 1950

By W. L. Crentz, E. E. Donath, D. Doherty

IN 1948, the United States used nearly six million barrels of petroleum products every day. Although substitution of synthetic fuels for the natural petroleum product is not here yet, large quantities of special-purpose coal will be required in ever-increasing volume as the domestic production of oil from other sources fails to meet demand and the production of synthetic fuels begins. Petroleum economists do not agree as to when the shortages of domestic oil will appear; but the increasing per capita consumption of oil, coupled with a constantly growing population drawing on a potential domestic oil supply estimated to be 85 billion barrels, sooner or later will result in demand exceeding domestic supply. When this situation comes about, the excess demand will be either eliminated by curtailment of consumption or the demand met by increasing importation of foreign oil or by the production of synthetic fuels. The first recourse would definitely retard the heretofore unbroken rise in American living standards, while dependence upon a foreign oil supply during a war or other emergency would be dangerous. On the other hand, the enormous coal reserves in the United States, plus sizable deposits of oil shale, indicate adequate means of augmenting a diminishing domestic oil supply. Some idea of the impact of an expanding synthetic liquid fuels program on the coal-mining industry may be gathered when it is considered that to supply just half of our present-day petroleum needs synthetically from coal would increase the coal output by about 500 million tons annually, using an 11,900 Btu bituminous coal as the plant feed. If either a subbituminous coal or lignite were used, the quantity required would be materially increased. Synthetic Fuel Processes: The principal synthetic fuel processes using coal as a raw material are the Bergius, or coal-hydrogenation process, and the Fischer-Tropsch, or gas-synthesis process. These two processes not only produce different end products, but the preparation of the coal used in each presents its own individual problem to the coal-preparation engineer. The hydrogenation process brings together a mixture of dry, finely powdered coal, catalyst, and heavy oil to form a paste. Addition of hydrogen under rather high pressure and temperature conditions brings about transformation of the coal to a liquid product, from which a high-grade gasoline and other motor fuels may be obtained. The Fischer-Tropsch process requires the production of synthesis gas, a mixture of carbon monoxide and hydrogen. At the Bureau of Mines Louisiana, Mo., demonstration plant, this gas is being made by reacting dried pulverized coal with carefully controlled volumes of oxygen and superheated steam. After purification and in the presence of the proper catalyst and suitable conditions of pressure and temperature, the hydrogen and carbon monoxide components of the synthesis gas react to form motor fuel. The two processes are not competitive but rather com-

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

IN 1948, the United States used nearly six million barrels of petroleum products every day. Although substitution of synthetic fuels for the natural petroleum product is not here yet, large quantities of special-purpose coal will be required in ever-increasing volume as the domestic production of oil from other sources fails to meet demand and the production of synthetic fuels begins. Petroleum economists do not agree as to when the shortages of domestic oil will appear; but the increasing per capita consumption of oil, coupled with a constantly growing population drawing on a potential domestic oil supply estimated to be 85 billion barrels, sooner or later will result in demand exceeding domestic supply. When this situation comes about, the excess demand will be either eliminated by curtailment of consumption or the demand met by increasing importation of foreign oil or by the production of synthetic fuels. The first recourse would definitely retard the heretofore unbroken rise in American living standards, while dependence upon a foreign oil supply during a war or other emergency would be dangerous. On the other hand, the enormous coal reserves in the United States, plus sizable deposits of oil shale, indicate adequate means of augmenting a diminishing domestic oil supply. Some idea of the impact of an expanding synthetic liquid fuels program on the coal-mining industry may be gathered when it is considered that to supply just half of our present-day petroleum needs synthetically from coal would increase the coal output by about 500 million tons annually, using an 11,900 Btu bituminous coal as the plant feed. If either a subbituminous coal or lignite were used, the quantity required would be materially increased. Synthetic Fuel Processes: The principal synthetic fuel processes using coal as a raw material are the Bergius, or coal-hydrogenation process, and the Fischer-Tropsch, or gas-synthesis process. These two processes not only produce different end products, but the preparation of the coal used in each presents its own individual problem to the coal-preparation engineer. The hydrogenation process brings together a mixture of dry, finely powdered coal, catalyst, and heavy oil to form a paste. Addition of hydrogen under rather high pressure and temperature conditions brings about transformation of the coal to a liquid product, from which a high-grade gasoline and other motor fuels may be obtained. The Fischer-Tropsch process requires the production of synthesis gas, a mixture of carbon monoxide and hydrogen. At the Bureau of Mines Louisiana, Mo., demonstration plant, this gas is being made by reacting dried pulverized coal with carefully controlled volumes of oxygen and superheated steam. After purification and in the presence of the proper catalyst and suitable conditions of pressure and temperature, the hydrogen and carbon monoxide components of the synthesis gas react to form motor fuel. The two processes are not competitive but rather com-

Jan 1, 1951

By H. R. Spedden

As part of its broad program of educational assistance-including grants, fellowships, and scholarships -Kennecott Copper Corp. offers summer employment opportunities for college students at each of its operations. Originally, summer job programs were intended primarily to help students defray their educational expenses. But as the nation's economy expanded with increased production and a growing demand for well-trained engineers, summer employment became an important means to help qualify future professionals and fill industry's need for them. Both the employer and the student thus derive benefits from such training.

Jan 6, 1967