Search Documents

By G. A. Stamboltzis, N. Arbiter, C. C. Harris

Fracture under low-velocity free-fall and double impact and under slow compression have been investigated. The pattern of breakage and the size distribution of resulting fragments of sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of maximum compression as determined by mathematical analysis. Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low-velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments. This work had its origin in a desire to understand three fundamental processes involved in autogenous comminution: namely; free-fall impact, double impact, and slow compression. To simplify the investigation, it is preferable to reduce the entire multi-stage fracture process to its most elementary form; that is, to study products resulting from a single-stage operation, such as the breakage of a specimen under single fracture conditions. The goal of this research is to study the energy utilization in the single fracture of brittle specimens and to relate the pattern of breakage and the resultant fragment size distribution with the nature of the material, the specimen size, the manner of load application, and the rate of loading. Published works on single fracture have mainly been concerned with tests on large (> 1-in.) irregular mineral pieces, especially coal and coke. These were mainly friability tests employing a single blow on closely sized pieces. More recently, small mineral specimens in the sieve range and glass spheres have been investigated.5-7 Kick8 has reported free-fall and double impact tests with large large cast-iron, cement, and clay spheres. The establishment of a minimum breaking height independent of size in the free-fall impact tests, and the direct proportionality between the minimum work required for fracture and the volume of the specimen in double impact tests were used by Kick as an experimental proof of his classical law of "Proportional Resistances." In the present work, spherical shapes were chosen because of their simple body geometry and consequent impact and stress field symmetry. Because the study involves several physical principles in connection with brittle-fracture, it may be of interest in fields where the strength of materials is of importance. APPARATUS The equipment for the free-fall impact testing is illustrated in Figs. 1 and 2. This consisted of a massive (17 x 17 x 3-in.) hard steel plate onto which specimens were dropped and a specimen release mechanism which could be set at any desired height up to 10 ft above the plate so that the impact velocity could be varied up to about 25 ft per sec. Double impact breakage is characterized by two points of loading situated at opposite poles. For this mode of breakage the apparatus was modified (Figs. 3, 4 and 5) so that a falling mass provided an impact of predetermined magnitude on a specimen resting on the plate. A spring-loaded device operated immediately after fracture to arrest the falling mass and to record its residual kinetic energy. Precautions were taken to avoid secondary breakage. Slow compression tests were performed on a conventional hydraulic testing machine, the specimen being held between two hardened parallel bearing blocks. In the case of glass spheres, carbide bits were used. Photoelasticity studies were performed on two-dimensional models held in a loading frame equipped with a force gauge (Fig. 6). The models were viewed in a polariscope and isochromatic fringe patterns were recorded photographically. SPECIMENS Sand-Cement Spheres: A series of sand-cement spheres were prepared by molding in spherical glass flasks.

Jan 1, 1970

By W. V. Green

Creep of tantalum was measured at temperatures from 0.6 to 0.89 of the absolute melting temperature. The creep curves include first, second, and third stages. Steady-state creep rate depends on the fourth power of stress. The activation energy for creep throughout this temperature range is approximately 114 kcal per mole, measured by the aT technique. Subgrain formation occurs as a result of creep strain, and pile-up dislocation arrays are observed in etch-pit patterns. BECAUSE of its high melting point-which is exceeded only by those of rhenium and tungsten—and its high room-temperature ductility compared to most of the other high-melting-point metals, tantalum will undoubtedly be utilized in an increasing number of high-temperature applications. Alloying studies directed toward increased high-temperature strength must use data on tantalum itself as a base line in order to evaluate the effectiveness of the alloying additions. However, to date, no systematic study of creep of tantalum at temperatures above one-half of its melting point has been reported in the literature. Conway, Salyards, McCullough, and Flagella1 have measured linear creep rate of tantalum sheet as a function of stress, but at only one temperature, 2600°C. This paper describes a relatively thorough study of the high-temperature creep of tantalum. METHOD Material Tested. The commercially supplied, l/2-innch-diameter tantalum rod used for this work was electron-beam-melted, cold-forged, rolled, swaged, cleaned chemically, and vacuum-annealed for 1 hr at 1000°C, all by its manufacturer. The vendor's analysis included 60 to 170 ppm C, 3.4 to 4.2 ppm H, 60 to 80 ppm 0, 15 ppm N, and a hardness ranging from 66 to 81 Bhn and averaging 76 Bhn. Creep eimens Used. Two creep-tested specimens are shown in Fig. 1. The 1/4 in.-diameter gage section was 3/4 to 1 in. long, and terminated either at shoulders 5 mils high or at 20-mil-diameter tantalum wires spot-welded to the circumference of the gage section. Both kinds of shoulders served equally well as fiducial marks for optical strain measurements. The spot welding did not alter the creep behavior in any detectable way; the 5-mil- high sharp shoulders did not result in any detectable localized effect on the strain. Before testing, each tensile bar was first mechanically polished -id then electrochemically polished according to the method referred to by Forgeng2 as the "Thompson Ramo Woolridge" method, which was suitable for tantalum after small adjustments of technique were made. Two tensile bars tested at low stresses had 1/8-in.-diameter gage sections and utilized only the weight of the bottom grip for the applied load. Although these diameters were smaller than were desired for other reasons, applied loads were known with high precision in the tests in which they were used. Testing Procedure. Two different constant-load creep-testing machines were employed, one of which has been described by Smith, Olson, and Brown.3 In both, the tensile bar is held vertically on the axis of a cylindrical tungsten tube or screen heater by threaded tungsten grips. The tensile bars and associated grips are heated by radiation from the incandescent heaters, which are heated by their own electrical resistance. Both testing machines use pins to hold the bottom grips in place. The load is applied to a tensile bar through hanging weights, a constant force-multiplication lever, a pull rod sealed to the chamber lid, and a top grip threaded to the pull rod at one end and to the tensile bar at the other. In one machine, the vacuum seal is a bellows with a low spring constant; in the other, the seal involves a rotating "0 ring". With the latter, rotation is converted to translation with a crank shaft, so that elongation of the tensile bar is accommodated with no change of tensile load. The incandescent tensile bar is viewed by an external optical system through slots in the radiation shields and heater, and an enlarged image is projected on a ground-glass screen. Gage-length measurements are made on this image with cathetometers on traveling microscopes. With regard to creep-test results, the two machines were identical. Thorium oxide coatings were applied to the threaded ends of the tensile bars, to prevent diffusion welding of the tensile bars to the grips during testing. Specimen temperatures were measured with an L. & N. optical pyrometer which had been calibrated against a standard carbon arc, and were corrected fir window absorption by calculation from the measured spectral transmittance of the quartz observation windows. Longitudinal temperature gradients in the tensile-bar gage length and temperature drifts during testing were detectable but small, and were estimated to be 10°C or less. Accuracy of temperature measurement was confirmed by comparing the temperature measured on the surface of a special

Jan 1, 1965

By Wllliam D. Davis

C OMMERCIAL production of oil in northeastern Oklahoma began in 1897 and in the next two decades this area became one of the greatest oil districts of the time. Its importance is now secondary, but thousands of wells in this area have produced uninterruptedly for more than thirty years. They are now classified as stripper wells. By means of what is known as water flooding their L. production can be considerably in- creased. This practice consists in injecting water under pressure into the sand surrounding an oil well, thus displacing the oil in the pores of the sand and forcing it into the oil well.

Jan 1, 1940

[A Aall, Christian H., M49 A Dir, Smelt & Ref, Am. Metal Climax, Inc., 1270 Ave. of the Americas, New York 20, N. Y. Aaroe, S. L., A54 A VP, W. S. Tyler Co. of Canada Ltd., P. O. Box 100, St. Catharines, Ont., Canada Abalos, Teodulo Q., J57 A Prod Frmn, Lepanto Cons. Mining Co., Lepanto, Mt. Province, Philippines Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abdullah, M. Y., J53 Dept. of Mines Res. Div., P. O. Box 1016 Tiger Lane,-Ipoh Peram, Malaya Abel, John F., Jr., J53 F Mine Engr, Thompson Creek Coal & Coke, Carbondale, Colo. Abell, Leo M., M31 B Const Supt, Phelps Dodge Corp., Morenci, Ariz. Abendroth, H. E., A57 Mangore Australia Pty. Ltd., 901 Hay St., Perth, W. Aust.,, Australia Abenius, Hakan V., M52 Falun, Sweden]

Jan 1, 1961

By N. S. Stoloff, M. Gensamer

The effects of temperature, grain size, and magnesium content on the strength and ductility of cadmium were studied in the range -269° to 23 °C. A sharp drop in ductility between -140° and -190°C marked a transition in fracture mode from ductile shear to inter gvanular fracture. The addition of up to 15.35 wt pct Mg in solid solution raised the transition temperature, and for two compositions produced basal cleavages. The relatively high ductility of unalloyed cadmium at cryogenic temperatures is attributed to temperature independence of the yield stress and the absence of dislocation locking. ALTHOUGH numerous studies have been made of the mechanical properties of cadmium single crystals,1-5 no comprehensive investigation of deformation and fracture in polycrystalline cadmium has been carried out. This investigation was initiated to determine the mechanisms of deformation and fracture in polycrystalline cadmium, and to attempt to correlate these mechanisms with the behavior of other metals of hexagonal close-packed structure. A second objective of this work was to determine whether the slip systems and mode of fracture of polycrystalline cadmium could be altered by reduction of the axial ratio, which is 1.886, through alloying. Dorn and co-workers' have been able to induce prismatic slip in magnesium through alloying to reduce the axial ratio. Single crystals of cadmium are so highly ductile that glide strains of 400 pct are observed at room temperature, and 80 pct at -269°c.l Failure in every reported case is by necking down and shearing off of the crystal. Cleavage in cadmium single crystals has never been observed. Magnusson and aldwin reported a ductile to brittle transition for polycrystalline cadmium at about —160 C for specimens tested at a strain rate of 0.05 in. per in. per min in tension. However, even at -196° substantial ductility was retained. The transition temperature was strain rate dependent, impact loading at 19,000 in. per in. per min raising the transition temperature to about -85°C while leaving the low temperature ductility unchanged. No information was given on microstructures or fracture mode, nor were stress-strain characteristics reported. In the present investigation, tensile tests were carried out on polycrystalline cadmium and solid solution Cd-Mg alloys to determine flow stresses, work-hardening behavior, fracture strength, and fracture ductility. Variables employed included temperature, alloy content (and c/a ratio), and grain size.Some compression data also have been obtained for comparison purposes. I) EXPERIMENTAL PROCEDURES A) Polycrystalline Cadmium. Two purities of cadmium were employed in this investigation. Cadmium of 99.95 pct purity was supplied by Belmont Smelting and Refining Co. Cadmium of 99.99+ pct purity was supplied by American Smelting and Refining Co. Threaded cylindrical tensile specimens were machined to give approximately a 1/2 in. long straight gage section with a reduced diameter of about 0.110 in. Specimens were heat treated in evacuated pyrex capsules in the range 140" to 290°C to produce desired grain sizes. All specimens were polished in a solution containing 320 g Cr03 and 20 g NaS04 in 1000 cc of H20. Occasionally this solution caused staining of the specimen, in which case a further polish with a solution of one part HN03 and two parts H202 in two parts ethyl alcohol was employed.' Tensile testing was carried out on a screw-driven Instron machine, at a constant rate of crosshead movement, which for most tests was 0.01 in. per in. per min. Load vs time, and therefore load vs total strain, were recorded. Temperatures from -196" to -40°C were obtained by passing nitrogen gas through a copper coil immersed in liquid nitrogen, and then feeding the gas into a jacket around the specimen. Tests at -269°C were carried out in a helium cryostat, at a crosshead rate of 0.1 in. per in. per min, with specimens of 1 in. gage length. Compression specimens were tested in a jig similar to one designed by ilman. The jig was mounted on the under side of the Instron crosshead. Load was transmitted by means of a rod connected to a movable part of the jig at one end, and the load cell at the other end. A downward movement of the crosshead applied a compressive load to the specimen.

Jan 1, 1963

By Donald E. Meyer

High current-low voltage EB-gun evaporation in an oil-free ultra-high vacuum system was found to be necessary, though not sufficient, for stability (300°C, 106 v per on) of aluminium gate MOSFET's and MOS capacitors not stabilized by a phosphorous glaze. five characteristics of the equipment used: 1) Vacuum purification of the aluminum charge, 2) Ionization of the evaporant by the electron beam, 3) X-ray formation, 4) Residual gases during evaporation, and 5) Metal film structure were studied as Possibly significant in MOS fabrication. EVAPORATION of contact metals common to the semiconductor industry historically has been accomplished with oil diffusion pump systems and various resistance heated evaporant sources as dictated by the type of metal evaporated. To meet a need for greater reliability of semiconductor devices, other metallization methods were developed. A good example would be application of the moly-gold contact system to integrated circuits with deposition by RF or triode sputtering.' More recently, fabrication of stable metal-oxide-silicon devices and circuits has put new demands on metallization. The purity of the thin metal films composing MOS structures is critical, particularly at the metal-oxide interface, and ultra-high vacuum metallization using sputter-ion pumping and electron beam gun (EB-gun) evaporation are well suited for the task. At this laboratory aluminum has been the most common contact-gate metal for both MOS capacitors and MOSFET's. In the earliest work with MOS capacitors, aluminum was evaporated from wetted tungsten filaments using both diffusion pump and ion pump vacuum systems. In spite of clean oxide techniques these capacitors were unstable under bias-tempera-ture stressing. Only after a switch to EB evaporation of aluminum were stable capacitors produced. Using the same techniques it was possible to make MOSFET's with equivalent stability. Stability data for a discrete MOSFET is shown in Fig. 1. This is a "clean" oxide gate (no phosphorus stabilization or no etch back of a thicker gate) having a thickness of lOOO? thermally grown on the (111) plane. Gate length after diffusion was 0.24 mils, and the devices were hermetically sealed. Stressing conditions were 300°C and 106 v per cm applied alternately as a positive and negative field for 10 min, 50 min, and 4 hr for a total stress time of 10 hr. An initial shift in turn-on voltage of 0.1 v was detected for 10 min of positive bias. All evidence at this laboratory indicated that while EB-gun evaporation of ultra-high purity aluminum was not sufficient for 300°C stability, it did seem to be necessary. There may well then be something inherent in the EB-gun deposition used which enhanced stability, and probably no single factor existed but rather a series of factors. It is the purpose of this paper to report on some of the investigations carried out to learn more about EB-gun evaporation in ultra-high vacuum systems. EXPERIMENTAL DESCRIPTION The EB-gun was self accelerated, had a maximum power rating of 10 kw, and used a water-cooled copper crucible able to hold a 20-g aluminum charge. The electron beam was bent 180 deg and focused by an electromagnet which also provided movement of the beam across the crucible. Normal power conditions in this work were 9 kv and 300 to 600 mamp. The gun can be described as high-cur rent/low-voltage and was quite different in its mechanism of operation from EB-guns with much higher acceleration potentials. An oil-free vacuum system capable of 5 x 10- l0torr, a quartz crystal rate and thickness monitor and a quadruple mass spectrometer completed the evaporation system, Fig. 2. A typical evaporation cycle consisted of a 3 to 4 hr pumpdown to the upper l0-9 range and evaporation at l0? per sec with the pressure in the bell jar not rising above 1 x 10"7 torr. Thickness control was 5 pct or less and could be automatically monitored and controlled. Five phenomena associated with the EB evaporation and considered as possible contributors to Ma performance included a purification effect, ionization of evaporating aluminum, X-rays, constitution of vacuum ambient during evaporation, and film structure dependence upon evaporation rate. These phenomena are now discussed. Vacuum Purification. The design of the EB-gun permitted purification of the aluminum charge by vacuum outgassing. Particular features included an efficiently water-cooled copper hearth with a capacity of over 20 g of aluminum and the capability for sweeping the beam across the charge. Such capacity meant that aluminum had to be added only after about every fifth evaporation. A new charge was not required each evaporation as is necessary with filament evaporation. An oxide "scum" which appeared on the charge could be completely cleared from the top hemisphere of the charge by sweeping with the beam prior to opening the shutter. An indication of the purifying effect was obtained by a series of analytical measurements on incoming aluminum, after melting but with little vacuum out-gassing, after 30 min outgassing, and the evaporated film itself. Either a solids (spark source) mass spectrometer or an emission spectrometer were used for analyzing the aluminum charge. Analysis of the evapo-

Jan 1, 1970

By J. W. Spretnak, J. N. Cordea

The gain boundary relaxation in high-purity aluminum, nickel, copper, and silver was studied by means of a low-frequency torsion pendulum. Both internal friction and creep at constant stress tests were conducted. A lognormal distribution in relaxation times was found to account for the relatively wide experimental internal friction peaks and the gradual relaxation behavior during the creep tests. This distribution was separated further into a lognormal distribution of relaxation time constants and a normal distribution in activation energies. A spread of up to ±6 kcal per mole in the activation energies accounted for the major part of the distribution. A "double-peak" internal friction phenomenon was observed in silver. The activation energies in kcal per mole derived from the grain boundary relaxation phenomena are 34.5 for aluminum, 73.5 for nickel, 31.5 for copper, and 41.5 for silver. It was found that the rain boundary relaxation strength in these metals increases with the reported stacking-fault energy. GRAIN boundary relaxation phenomena have been observed in a large number of polycrystalline metals and alloys. Numerous investigations have been conducted to study the structure of the grain boundary through this relaxation process. One of the first investigators was Ke1-4 who observed that the activation energy for grain boundary relaxation in aluminum, a brass, and a iron was about the same as that for volume diffusion. He concluded that the grain boundary behaved as if it were a thin liquid layer with neighboring grains sliding over one another. Leak5 conducted experiments on iron of a higher purity and observed that the grain boundary activation energy is comparable with that of grain boundary diffusion. He suggested that, in metals where this relationship holds, the damping may be caused by a reversible migration of grain boundaries into adjoining grains. Nowick6 has presented an interesting view of inter-facial relaxation with his "sphere of relaxation" model. A relaxed interface is represented as one where the shear stress is greater than the normal value along the edges and zero in the interior of the interface. The region of the stress relaxation is pictured as a sphere surrounding the interface. From his calculations Nowick concluded that the slip along an interface is directly proportional to its length. Therefore, the time of relaxation, T, depends on the size of the relaxation interface. This means that in the Arrhenius relationship, t = TO exp[H/RT], valid for atom movements, the relaxation time T is predicted to be proportional to the grain diameter through the pre-exponential term, TO. Since the internal friction can be given as Q-1 = ?j wt/(1 + w2r2), where ?J is the relaxation strength and w is the angular frequency, an increase in grain size at a constant frequency will shift the peak to a higher temperature. A great deal of work has been done to determine the exact relationship between the internal friction and grain size.1,5,7,8 In metals, the grain boundary peaks are found to be lower and broader than predicted theoretically.' The above model can explain this by a distribution in the size of the interface areas, represented by a distribution in the parameter tO, and an overlap of spheres of relaxation, represented by a distribution in activation energies. Both these phenomena result in an over-all distribution in the relaxation time, which could affect the internal friction peak height, breadth, and also position. This relationship between the experimental data and theoretical calculations appears very promising in the study of interfacial relaxation mechanisms. THEORY A lognormal distribution in t can sometimes be used to adequately describe the spectrum of relaxation times governing an anelastic relaxation. wiechert9 originally suggested such a distribution to explain the elastic after-effect in solids. This choice is particularly applicable to grain boundary relaxation when considering Saltykov's work.'' He found a lognormal distribution in the grain sizes within a metal. Recently Nowick and Berry11 have introduced a log-normal distribution in T into the theoretical internal friction equations. The form of the distribution function is where z = In(r/rm), and Tm is the mean value of t. The parameter ß is a measure of the distribution and is the half-width of the distribution when is l/e of its maximum, IC/(O). Nowick and Berry have described the methods to obtain the parameters Tm, ß, and ?,J from experimental internal friction and creep test data. In the idealized case, where only one relaxation event occurs with one relaxation time, only ?J and T are necessary to completely describe the event, and 0 = 0. For the broader internal friction curves 6 is some positive number greater than zero. The larger the 6, the greater is the half-width of the distribution in In t.

Jan 1, 1967

By H. E. Elliott, R. S. Busk, A. T. Peters

ONE of the problems of the fabricator of metals and alloys is the propensity of some composition ranges toward abnormal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, o per cent Al, 2 per cent Zn, 0.2 per cent Mn) and G alloy (Mg, i0 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other metals. Jeffries and Archer' have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. of abnormal local grain growth was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. r) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The Dow Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germination," since this term has been defined' as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By E. C. Bain, E. S. Davenport

When annealed carbon, or low-alloy, steels are suitably heated the ferrite (alpha iron solid solution) and the carbide, of which they are composed, react together to form a single solid solution of carbon (and other elements) in gamma iron (austenite). This reaction may begin only at a certain minimum temperature called the eutectoid temperature. The first ferrite and carbide thus to react together do so in definite proportions known as the eutectoid composition. With further heating the original constituent that is present in excess is dissolved in the austenite until exhausted. Whether the excess constituent be ferrite (hypoeutectoid steels) or carbide (hypereutectoid steels) the procedure is much the same, and upon slow cooling the homogeneous austenite expels the excess of either (proeutectoid ferrite or carbide) until the eutectoid composition is reached. Thus the reaction upon heating is strictly reversed upon cooling and accordingly an equilibrium diagram of this process may be constructed. Such an equilibrium diagram concerns itself only with the temperatures involved and with the proportions and compositions of the phases developed under conditions that suffice to permit equilibrium. Specifically it has no concern for the type or mode of distribution of these constituents nor with any extra-equilibrium conditions such as undercooling, which is almost universally encountered in metals. Actually, however, of great importance is the sluggishness toward equilibration caused by the not inconsiderable time involved in diffusion. Thus instead of the theoretical transformation point AF, we find for a certain rate of heating or cooling the use of the designations Ar and Ac (transformation temperature found on cooling and upon heating). These figures obviously have no particular meaning except as measured and expressed for a definite heating or cooling rate, and represent the apparent temperature displacement caused by an inadequate time allowance. In this paper are presented the results of a study of the time required for the transformation of austenite to ferrite and carbide at a variety of temperatures and also of the time required for the reaction austenite? martensite at the temperatures at which this reaction occurs instead of

Jan 1, 1930

By William J., Coulter

IN the early days of Colorado mining, between 1880 and 1900, when Leadville, Kokomo, and Robinson were boom mining camps, the entire area around Climax for a matter of fifteen miles was overrun with prospectors, so the mineralized outcrop at Climax was not unknown. The principal interest in minerals during this period was in gold, silver, and lead, and since the Climax outcrop showed none of these it drew little attention. Geology played an important part in bringing prospectors to the very edge of the Climax deposit. The Mosquito fault, which crosses near the base of Bartlett Mountain, continues as an important geological structure, at least as far as Leadville some twelve miles distant, and at the base of Bartlett Mountain the vertical throw on the fault is estimated to be between 2000 and 5000 ft. The sedimentary beds known to the Leadville district are all present on Bartlett Mountain to the north of the Mosquito fault, which cuts them off abruptly, and exposes the Pre-Cambrian rocks that underlaid them, so the prospectors, who were searching for gold, silver, and lead in the sediments

Jan 1, 1946

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By Ta M. Li

Expanded mine-mill capacity and greater operating flexibility are part of the dramatic changes taking place in the Tennessee mining operations of Asarco, Inc. Climaxed by the recent start-up of the $6.3 million Young mill in September 1975, Asarco has pushed Tennessee back into number one position as the leading zinc mining state. Furthermore, start-up of the Young mill is expected to insure a much-needed and continuing domestic zinc supply, at a time when US mines can only supply one-half of 1975 domestic consumption.

Jan 5, 1976

By Gilbert Soler

PRODUCERS of alloy steels recognize the importance of chemical composition in rela-tion to the hot-working properties and the typical surface defects found in their prod-uct. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization character-istics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures as well as the tendency toward scale formation and decarburization, This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative impor-tance of these factors in relation to the hot-working properties and surface charac-teristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel.

Jan 1, 1940

By M. J. Blackburn

The ordering reaction and its effect on dislocation awangements in alloys based on Mg3Cd has been studied by transmission electron microscopy. Ordering occurs by the growth of ordered domains until they impinge, thus producing an antiphase domain boundary (APB) network. In the disordered alloy, slip is confined to the basal plane while in the ordered condition slip occurs on the basal, prism, and pyramidal planes. Superdislocations have been identuied on these planes and their origin and expected spacings are discussed and compared with the observations. The APBs between the dislocation pairs have been resolved and have proved useful in the identification of superdislocations. Observed slip structures are related to the changes in mechanical properties produced by ordering. At high temperatures magnesium and cadmium form a continuous series of disordered hexagonal solid solutions. At lower temperatures three ordering reactions occur; two based on the compositions Mg3Cd and MgCd3 are transformations to DO19-type superlattices while alloys based on the composition MgCd transform to a B19 lattice. The ordering process in alloys near the composition Mg3Cd has been studied by several workers'-4 and it has been shown to be a first-order type transformation. The variation of mechanical properties with the degree of order and temperature have been reported in some detail by Stoloff and Davies.5 It was shown that the disordered alloy was stronger and less ductile than the ordered alloy, the differences being attributed to changes in the number of active slip planes and to the presence of short-range order in the disordered alloy. In this investigation the ordering reaction has been qualitatively followed by transmission electron microscopy. The effect of this ordering transformation on the dislocation arrangements in deformed specimens has been studied in some detail. EXPERIMENTAL Alloys were melted in a stainless-steel crucible under a flux and chill cast; both melting and casting were performed in an argon atmosphere. The ingots were hot-rolled and tensile specimens cut from the resultant strips. Some large-grained specimens were grown by the strain-anneal method. Heat treatment was carried out in inert atmosphere furnaces and in oil baths at the lower temperatures. Thin foils for transmission electron microscopy were produced by electropolishing in a cooled solution (temp = -40°C) containing 50 cu cm of nitric acid and 180 cu cm of methanol at a potential of 10 v. The ordering reaction was followed by transmission electron microscopy, X-ray, and electrical resistivity measurements but this paper will be concerned chiefly with the electron-microscopy results. Much of the work described in this paper was performed on an alloy containing 26.10 at. pct Cd although two of the micrographs are taken from work on a 25.55 at. pct Cd alloy. RESULTS i) The Quenched Solid Solution. Specimens which were quenched from above the critical temperature showed diffuse superlattice reflections. sark-field analysis on these reflections failed to reveal the presence of ordered domains and thus the superlattice reflections were assumed to arise from regions of short-range order. Quenching from temperatures of 400" to 450°C results in the formation of dislocation loops and helical dislocations. Such defects have been observed and analyzed in detail in several hexagonal metals6-' and as the crystallography and interactions of such loops appear similar in this alloy they will not be reported in detail. Fig. 1 shows a high density of loops

Jan 1, 1968

By H. Foster Bain

(San Francisco Meeting, October, 1911.) [SECRETARY'S NOTE.-This paper, presented in oral abstract, at the San Francisco meeting, was not at first supposed by Mr. Bain to be required for publication in the Transactions; and the excursion to Japan, in which he took part, immediately after the San Francisco meeting, delayed his presentation of the manuscript. After his return to San Francisco, Mr. Bain, in view of the importance of his paper and its discussion, kindly furnished it in full. The delay in its publication (since it was received in April last) has been due, partly to the circumstance that other contributions had meanwhile acquired the "right of way," and partly to the consideration that, the situation contemplated in Mr. Bain's paper having remained practically unchanged, the paper and its discussion would not lose force or timeliness by this lapse of time.-J. S.] No acute observer of public affairs can have failed to observe a growing disposition on the part of the public to change emphasis in government from political equality to social justice. When our own government was founded it was felt to be sufficient to secure to each individual the fullest possible freedom of opportunity, and such a scheme was excellently adapted to the rapid development of a large territory having a small population. As the number of people in a given area increases, there are more points of contact and conflict; each must move in a smaller orbit, and there must be more regulation. Germany is making faster progress in industry than is any other country. The principal reason is the insistence there on team-play. In Germany there are fewer multimillionaires and more socialists (spelled with either a big or little " S ") than in any other of the leading countries; but Germany wins trade and is steadily improving the conditions of life for her citizens. To some, the change from the freest individualism is welcome; to others it is intensely unacceptable. To this fundamental difference in view-point may be imputed much of the vigor with which the controversy regarding coal-lands has been waged. That present conditions in Alaskan coal-fields are extremely unsatisfactory is generally recognized, but there are wide dif-

Aug 1, 1912

By John A. THOMPSON, Pazcl D. Torrey, Frank Breayster

DISCOVERY of natural gas in the Dundee field of New York in February, 1930, and the subsequent discovery in Tioga in September of that year, focused the attention of the natural-gas industry on the enormous possibilities of production and distribution in - the most populous area of the United States-New York and New England. Prior to 1926 the natural-gas industry in New York State had settled into a definite and limited policy, with the distributing companies controlling the output from its discovery to the ultimate consumer. Production amounted to between G and 7 thousand mil- lion cubic feet a year, with another 10,000 million feet imported from Pennsylvania for distribution in New York State. This gas was primarily from the Medina sand stone in. the western part of the state.

Jan 1, 1932

By L. S. Darken

IN the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be repre-sented satisfactorily by the simple equilibrium expression K - (p1)p1 (p2)p2 . (R1)r1(R2)r2 . where (P) denotes the concentration of a product and (R) the concentra-tion of a reactant in the reaction r1R1 + r2R2 + . . . Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a com-ponent is not proportional to its true mol fraction, But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple com-ponents and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satis-factorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature as ionization or the occurrence of polar and nonpolar molecules-are presumably less effective in metal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By P. Payson

Intergranular corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinnüberl suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain3 say that "intergranular attack—may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small percentages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion. and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By J. D. Meakin

The self-diffusion coefficients of ß tin have been deterttlltled using a plating and sectioning technique. The principal diffusivities pavallel and perpendicu1ar to the "c" axis are given by the Arrhenius relations Dc = 8.2 exp (-25,600/RT) sq cnl per sec and Da = 1.4 exp (-23,300/RT) sq cm) per sec. The results are discussed in terms of a vacancy mecharism of diffusion. In conjunction with an investigation of diffusion in dilute indium-tin alloys we have reexamined self-diffusion in tin single crystals. The published self-diffusion coefficients of tin, eensham') have always appeared anomalous in comparison to diffusion data for other metals and do not correlate with parameters derived from creep tests.' In addition to the necessity of confirming the self-diffusion values for use in analyzing the alloy work, self-diffusion in an anisotropic lattice is of considerable fundamental interest and confirmation of the published data seemed worthwhile. For a crystal with an axis of symmetry three-fold or higher the diffusivity at an angle 6 to the axis is given by D? = (Da - Do) sin2?+ Do [1] where Da and Do are the principal diffusivities perpendicular and parallel to the axis. For a particular diffusion mechanism, again in a crystal of axial symmetry, these principal diffusivities are [2] Do - ? ?i2 COS?i In these expressions ?i is the displacement undergone by the ith atom and 8, is the angle this displacement makes with the symmetry axis. In this, as

Jan 1, 1961