Search Documents

By John W. Weeton, Max Quatinetz, Robert J. Schafer

Nickel powders of 1-, 0.4-, and 0.2- average particle size were combined with 0.05- p MgO powder. Oxide was added in quantities of 4, 12, and 20 vol pct. The mixtures were vacuum hot pressed and extruded at 2100°F. In spite of a general tendency to growth of oxide particles during processing, dispersions of fineness comparable to those of Sintered Aluminum Powder, SAP, were achieved. A small amount of oxide considerably improved 1800°F stress-rupture strength, but further oxide addition resulted in a decrease of strength. RECENTLY there has been much speculation concerning the requisites for strong and stable dispersion-strengthened alloys. The nature of the dispersed phase, the stability of the alloys, and variables influencing the mechanical properties of alloys have been given consideration. Such topics have been reviewed by Bunshah and Goetzel. Of the many parameters related to the mechanical properties of dispersion alloys, mean free path between dispersed particles (a measure of the fineness of the dispersion), particle size, and vol pct of the dispersed phase have been shown to be very important. Generally, strength increases with decreasing mean free path, and there is an optimum vol pct of dispersed phase. Just how fine a dispersion ought to be is somewhat open to debate, but Irmann, Lenel, Backensto, and Rose, Gregory and Grant,4 and others have shown in the original SAP-type alloys, aluminum plus aluminum oxide alloys, that better strength is generally obtained with finer dispersions and the best strengths were obtained when the mean free path was less than . Further, Cremens, and rant' showed that in nickel plus aluminum oxide alloys, stress-rupture strength at 1500°F was definitely increasing with decreasing mean free path. In their investigation, however, the finest dispersions that were produced were about 2.0 mean free path. To determine the potential of the nickel plus oxide type of product, it would be neces- sary to obtain dispersions analogous to those of SAP alloys; namely, ones where the mean free path between oxides is less than . Unfortunately, however, it is very difficult to produce extremely fine dispersions of oxides in metals other than those which naturally form refractory oxide skins. There are several approaches to this problem including such procedures as mechanical mixing, internal oxidation, reduction of mixed oxides, and metal deposition from solution. Work at the Lewis Research Center has shown that metal powders 0.1p or finer could be produced by ball milling, when selected grinding aids were utilized.' Because these unusually fine powders were available, it was an initial objective of this study to determine if by mixing of these fine Ni powders with various amounts of MgO (0.05) a fine dispersion of MgO in Ni comparable to those in Al-Al203 might be achieved. A second objective was then to attempt to relate the parameters of structure to 1800°F stress-rupture strength of the alloys. Nickel powders of 1-, 0.4-, and 0.2-p average particle size were combined with 0.05- average particle size MgO powder. This oxide was added in quantities of 4, 12, and 20 vol pct. The mixtures were hot pressed and extruded at 2100°F.

Jan 1, 1962

By H. L. Marcus, C. D. Turk

Titanium was physically vapor-deposited by electron beam high rate evaporation. Rates of 50,000 and 85,000Å per min at deposition temperatures of 480°, 535°, and 595°C were used. Deposited thickness ranged front 0.004 to 0.010 in. The evaporated titanium had a high degree of basal Plane texture. The specimens were tested in tension at temperatures ranging from 78° to 520°K. From the data, the yield stress, thermal component of the yield stress, and work hardening characteristics were found as a function of temperature, deposition rate, and deposition temperature. It was found that Taylor's equation, best fit the work hardening data with m = 1/2. MANY investigations have been made on the tensile deformation characteristics of commercial- and high-purity titanium.1"7 The data obtained from these experiments emphasize the fact that the mechanical properties are generally related to the method of production. The correlation of mechanical properties to production history arises from the dependence of impurity concentration on the extraction and melting technique used. Additional effects are derived from crystallographic texturing which can result from fabrication history. Lee and Backofen8 and other investigators9 have shown that crystallographic texturing in titanium sheet has a significant effect on the deformation characteristics. Bunshah and Juntz10 prepared high-purity titanium by high rate physical evaporation techniques. These authors found the deposited material to have a columnar structure with grain sizes ranging from 12 to 104 µ, depending upon the substrate temperature. The room-temperature strengths of the coarse-grained distillate were similar to arc-melted, rolled. and annealed crystal bar titanium. Commercial-purity titanium was also produced experimentally in our laboratory using high rate physical vapor deposition techniques. The commercially pure material has a finer structure than the high-purity distillate,10 and is highly textured. Since the method of preparation and degree of texturing affect the mechanical properties, a research program was initiated to determine the temperature dependence of the yield stress and work hardening characteristics as a function of high rate deposition parameters. This paper relates the results of the investigation. EXPERIMENTAL A) Material Preparation. The titanium was received in the form of commercial-grade 0.096-in.-diam wire which has a composition of 0.016 pct C, 0.0037 pct N, 0.110 pct 0, 0.011 pct H, 0.05 pct Mn, 0.051 pct Fe. balance Ti. The wire was continuously fed into a vacuum evaporation unit as shown schematically in Fig. 1. The deposition chamber was evacuated, purged with argon, and reevacuated to a pressure of 10-5 Torr which was maintained during deposition. A focused electron beam was used to evaporate the titanium from a water-cooled copper crucible. The titanium vapor was condensed onto a preheated titanium substrate. The temperature of the substrate was controlled within ±5°C for the deposition temperatures of 480°, 535°, and 595°C. Control of the input power enabled the use of two deposition rates. 50,000 and 85,000Å per min. The evaporated titanium had a final analysis similar to that of the input titanium, within experimental limits. B) Testing. The evaporated titanium was physically stripped from the titanium substrate and machined into tensile specimens with 1-in. gage lengths. In addition, tensile specimens of as received annealed 35-A titanium sheet with a 20 µ grain size and 45 pct cold-rolled 35-A were also prepared. All specimens were tested in tension in an Instron at a strain rate of 3.3 x 10"4 in. per in. per sec. Proportional limit has been used as a measure of yield strength. Tests were conducted at 78°, 220°, 300°, and 520°K. Metallography, X-ray diffraction, and electron microscopy were used to correlate structure with the deposition parameters and mechanical properties. Room-temperature X-ray measurements were made to determine the phases present. Pole figures and a scans were made to determine deposition texture. Because the vapor deposition was symmetrical about the normal to the substrate, there was no preferred di-

Jan 1, 1969

By H. C. Goodrich

THE earliest record of copper production from the state of Utah comes from "The Resources of Utah," by. Mr. Fabian, in 1872, wherein it is stated that the. Mammoth mine of East Tintic was located in 1870 and that the ores yielded a large percentage of copper, silver and gold. It is also stated that shipments had been made to Swansea, England, which assayed between $200 and $300 per ton. The Mammoth-Copperopolis mine was located in, 1870 and sold the year following to an English syndicate. Some copper was shipped to. England and in 1873 there was constructed a 15-stamp mill and two copper smelting furnaces; these were operated a few months and before the end of the year were closed down and the property sold for debt. . This property -vas reorganized in 1879 and is at the present day a producer, though its principal product now is lead and silver. While a certain amount of copper has always been coming from the various lead-silver camps of Utah, the real history of copper in Utah should start with the discovery of the mines in Bingham Canyon, located about 25 miles to the southwest from Salt Lake City.

Jan 1, 1925

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn' observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,' Houska and Averbach,' and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.' cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.' Finally, the possibility of stress-induced order at dislocations, schoeck locking,' must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-' mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

By R. A. Burton, J. T. Hansford, D. A. T. Donohue

Substantial evidence indicates that many petroleum producing horizons contain naturally occurring, ordered fracture systems and that within a particular geologic zone, vertical fractures induced in wellbores often will be directed along a particular compass direction. Both conditions will seriously alter the fluid displacement behavior within reservoirs. In this study the effect of induced fracture orientation and length on sweep efficiency is determined for a five-spot pattern. In general, it is assumed that all wells are fractured and directed along the same compass direction. Using the electrical analog to steady state, two-dimensional fluid flow in porous media, boundary conditions are obtained from which flood fronts are tracked numerically. The numerical computations require a particle tracking routine for approximating flood front histories. It is shown that recovery is sensitive to the length and orientation of fractures for the pattern studied. with the proper design of fracture-pattern systems, recovery can be enhanced considerably. INTRODUCTION Hydraulic fracturing introduced in 1949l gave the industry a rather inexpensive means of increasing the fluid injection or production capacity of wells. It has been used with particular success to increase the production rate of wells completed in tight formations, such as in western pennsylvania2 where producers have fractured in depleted or near-depleted fields and observed economic responses. Once the natural energy declines in such a reservoir where all wells have been fractured, waterflooding is generally suggested as means of further increasing recovery. Of the dual objective sought in waterflooding — high injectivity and high breakthrough sweep efficiency — the former condition can be obtained if all wells in the flood pattern are fractured; the latter condition should depend on the nature of the fracture system. Considerable theoretical work has been published on the nature of fractures induced in boreholes.3-5 Although discussion persists concerning the possibility of forming a horizontal fracture at a given point within the wellbore, it is generally conceded that only vertical fractures will develop below a given depth, i.e., where the fracturing Pressure is less than the overburden load. Given the fact that fractures will be vertical in most cases of interest, it is also important to know whether there is order to fracture orientations within a given geological region. Kehle has suggested that in tectonically relaxed areas of uncomplicated geology, the stresses are fairly uniform and all fractures in the region should be parallel.5 Dunlap arrived at a similar conclusion in a theoretical investigation of localized stress conditions surrounding the borehole.6 He concluded that most vertical fractures are propagated in a preferred azimuthal direction. Fraser and Pettitt, in extending these theoretical suggestions to a specific field case, used an impression packer to record both a vertical fracture and the orientation of this fracture in the wellbore of a well in the Howard Glasscock field, Tex.7 Use of this information enhanced the waterflood recovery of the field. Anderson and Stahl also used impression packers on three fractured wells in the Allegheny field. N. Y.. and found that the fractures were oriented more or less along the same compass direction.8 Orientation of the fractures in this manner depends on the stress condition within the formation during fracturing. Elkins and Skov have demonstrated that a natural, oriented, vertical fracture system exists within the Spraberry field? Heck suggests

Jan 1, 1969

By Mark J. Klein

An internal-friction profile induced by nitrogen in Cr-35 at. pet Re was studied as a function of nitrogen concentration and heat treatment. From these studies, the solubility of nitrogen in this alloy was deduced. The equilibrium solubility of nitrogen in chromium does not appear to be substantially changed by the addition of 35 at. pet Re to chromium. However the precipitation kinetics of nitrogen from solution are significantly decreased. IT has been found that rhenium has a beneficial effect on the low-temperature ductility of Group VI-A metals. As part of a study to investigate the mechanism of this increased ductility, it was of interest to compare the concentration of interstitials retained in solution in one of these ductile bee alloys with the concentration retained in solution in its base metal. In this regard, a study of the solubility of nitrogen in ductile Cr-35 at. pet Re was selected for this phase of the investigation because the solubility of nitrogen in the base metal, chromium, has been determined over a fairly large temperature span.1-3 In addition, nitrogen is known to have an embrittling effect on chromium,4 but does not appear to have a comparable embrittling effect on Cr-35 at. pet Re.5 The experimental method selected for this study was the measurement of internal friction. This technique allows interstitial-concentration measurements to be made in bee metals that are sensitive to small changes in the concentration of a particular interstitial, even when other interstitials are present. When subjected to a cyclic stress, interstitial atoms in solid solution give rise to an internal-friction peak whose origin is the stress-induced ordering of interstitials into preferred lat- tice sites. These internal-friction peaks signify a dissipation of elastic energy which is greatest when the period of oscillation is comparable with the relaxation time for the attainment of an equilibrium interstitial distribution. For dilute interstitial binary alloys, the height of the internal-friction peak is proportional to the concentration of interstitial atoms in solid solutions. snoek8 has shown that the internal friction, Q-1, may be expressed by the equation where A is the relaxation strength, ? is the angular frequency, and 7 is the relaxation time. The relaxation strength, A, is proportional to the concentration of interstitials taking part in the relaxation if no interaction occurs between solute atoms. Thus values of peak height, which can be determined as a function of temperature, give a measure of the relative concentration of interstitial atoms in solution at various temperatures. If equilibrium has been attained, the peak heights will be proportional to the interstitial solubilities. The constant that relates A to the interstitial concentration can be determined experimentally from peak-height measurements as a function of concentration for specimens of constant crystallographic orientation. When this has been done, Q-1 measurements can be used to determine solubilities according to the equation C - KQ-1 where C is the soluble interstitial concentration and K is a constant that can be experimentally determined. It is possible, however, that lattice imperfections may bind interstitials to certain lattice sites. Internal friction does not measure these interstitial~, but does measure interstitials which are free to move in the normal lattice sites when subjected to an applied oscillating stress. On alloying the pure metal with a substitutional

Jan 1, 1965

By Y. C. Liu, W. R. Hibbard

Based on pole figure data and microstructural observations, the re-crystallization orientation found in a copper strip previously cold-rolled 99.5 pct from a single crystal with an initial (110) [112] orientation may be described as: a 30° rotation, clockwise and counterclockwise, about octahedral poles of the cold-rolled texture such that all four poles function at a low annealing temperature (400°C) and only three of them function at high temperatures (500' to 1050°C). The relative intensity of deformation stresses on various slip planes can be correlated with the choice of poles affecting the rotations found in the recrystallized orientations. ROTATIONAL reorientation about the poles of densely packed crystallographic planes is an important characteristic of secondary recrystallization" in face-centered cubic metals. Some evidence has also been interpreted to show that such a rotational relationship also exists in the primary recrys-tallization process." In an investigation of the crystallographic relationships in the recrystallization process, several aspects of the experimental procedure should be considered. With cold-rolled poly-crystalline metal as the initial material, pole figure analysis leaves many ambiguities as to whether or not simple indices can be assigned to adequately represent its orientation. The rolling texture does not consist of a single texture. Minor deformation textures are usually present. In all cases, twin textures are present. The presence of both minor and twin deformation textures influences the recrystallization texture. In order to study the recrystallization mechanism, a more precise knowledge of the history of the material before recrystallization is necessary. Tensile deformation of a single crystal usually produces residual stresses which are concentrated at slip bands. Since the exact nature and orientation of these potential nuclei sites cannot be experimentally evaluated, the tensile deformation of a single crystal was not considered adequate. From the work done by Barrett and Steadman6 n copper, it appeared that cold rolling of a single-crystal specimen with an initial (110) [112] orientation would yield a specimen which fulfills the conditions required for the present investigation, namely a highly preferred single rolling texture with relatively homogeneous stress distribution. By investigating the recrystallization texture of this material, additional details of reorientation during recrystallization might be obtained. The purpose of this paper is to describe such an investigation. Experimental Procedure Copper used in the present investigation was cathode sheet with a purity of 99.94 to 99.97 pct. A copper single-crystal specimen, 1.15x0.8720x0.5322 in. (thickness) was cut from a cylindrical crystal which was grown in a Bridgman furnace.' The cutting was accomplished on a horizontal milling machine operated at a very slow speed to obtain a (110) plane in the rolling plane and a [112] direction in the rolling direction. The disturbed surface was removed by electrolytic polishing in dilute orthophos-phoric acid (H3PO4) with a specific gravity of 1.14, and a current density of about 1 to 2 amp per sq cm. A 3-min polishing was needed to eliminate the disturbed surface causing Debye-Scherrer rings and a 45-min polish produced a surface which yielded sharp rounded Laue spots. It was estimated that about 1/16 in. of metal was removed from the original cut surface. The final orientation of this specimen before rolling was about 2" from the (110) plane in the rolling plane with a [112] direction aligned in the rolling direction. It is possible that a small amount of strain was still present in the cube despite the fact that the Laue spots seemed very sharp. It is doubtful, however, that this would be an important factor after a subsequent rolling reduction of 99.5 pct. This copper specimen was rolled on a laboratory rolling mill with two highly polished rolls 37/8 in. in diam in the following manner: 0.010 in. per pass to 50 pct reduction, 0.005 in. to 70 pct, 0.002 in. to 85 pct and, finally, 0.001 in. per pass to a 99.5 pct reduction. Specimens, about 1 in. sq with the rolling edges intact, were cut from the rolled strip by the electrolytic method previously described, after the strip

Jan 1, 1954

By Charles Stein

The effects of several different prior treatments an the creep behavior of 99.9995 pct aluminum at 260°C and 1000 psi canstant stress are compared with annealed specimens. Quenching from 538oC, irradiation with 2 mev electrons, and tension-compression room temperature fatigue damage were used to change the substructure of the specimens prior to their creep testing. The quenched and the irradiated specimens showed a larger primary and transient stage contribution to the creep curve than those specimens which were only annealed prim to creep testing. The specimen receiving prior fatigue damage at room temperature showed no first stage or transient creep when tested under identical conditions as the above specimens and had an average creep rate seven orders of magnitude lower than that of either the annealed, the quenched or the irradiated creep specimens. In a previous electron transmission microscopy investigationl of the substructure developed during the creep of pure aluminum at 0.57 Tm, it was noted that a large concentration of vacancy loops and dislocation loops were present in and near the subboundaries while the interior of the subgrains contained few of these defects and had a low dislocation density, see Fig. 1. Yim and Grant2 and Hazlett3 have shown that the presence in nickel of a substructure developed by prior cold work effectively reduces the primary and transient contributions to the creep curve. Hultgren,4 McLean,5 Gervais, Norton, and Grant,6 Chang and Grant,7 and others have shown the same effect with the higher stacking fault energy material, aluminum. However, the specific defect responsible for the change in the creep behavior developed by the prior cold work was not established. Specifically, what effectively interfered with dislocation motion in these materials at elevated temperatures? Was it jogs on dislocations produced by their interaction with other dislocations or with vacancy or dipole loops, see Fig. 1, or did the subgrain walls determine the mean free path for glissile dislocations? This would be a realistic possibility only if subgrain boundaries are effective barriers to dislocation motion. The ability of a subgrain boundary to act effectively against glissile dislocations depends on the number and the arrangement of dislocations in the subboundary,8 which in turn is a function of the creep strain.' This paper compares the creep rate of specimens possessing a large vacancy concentration to that of annealed specimens and with specimens having a stable subboundary wall containing Lomer locks produced by prior fatigue damage. EXPERIMENTAL PROCEDURE Vacancy Loops. Aluminum creep specimens, 99.9995 pct pure, were machined from zone refined rod to a 2-in. gage length and a cross-sectional area of 0.025 in. These specimens were annealed at 538oC, 1000°F, for 10 min and quenched into ice water. They were then reheated to the creep test temperature of 260°C, 500°F, and held at this temperature for 18 min to al-low for vacancy condensation and loop formation. The specimens were subsequently creep tested at 1000 psi constant stress at 260°C. The temperature along the gage length was monitored by three Pt-Pt, 13 pct Rh thermocouples, two embedded in the upper and lower shoulders of the specimen and one attached to the mid-point of the gage length- The temperature gradient was held to ± l°C or less throughout the Creep test. Elongations were measured by two LVDT's 'connected in an averaging 'On-figuration, with quartz extension arms placed against the specimen at the extremes of the 2-in. gage length. i K 3J?--' * *H - >^> - ' ^L r 77 . *y J OJL, J Fig. 1—Transmission electron micrograph of pure aluminum strained 8.2 pct at 260°C and 1000 psi constant stress. Note the presence of numerous loops near the light dislocation tangle

Jan 1, 1970

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

By D. L. Sikarskie, B. Paul

A theory is presented for the static penetration of a single rigid wedge into brittle material. The material considered is one which exhibits both crushing and chipping phases in the penetration process. If the wedge angle and three parameters are specified, the theory predicts forces and associated penetrations during both the crushing and chipping phases. For certain ranges of the parameters agreement with the limited experimental data available is promising, except for the initial phase of the penetration process where refinements on the proposed theory are required. The theory also predicts that for certain values of the wedge angle and other known parameters, the chipping process does not occur and penetration is due entirely to crushing. When viewed in detail, the drilling of rock by percussive means involves, among other things, system dynamics, actuating forces, dynamic stress levels and the actual penetration mechanism of the bit into rock. If rock drills are to be significantly improved, a thorough understanding of the entire system would be highly desirable. In this paper, one aspect of the system, namely the mechanism of penetration of the bit, will be studied in detail. It has been found1 that for the velocities encountered in percussive drilling (of the order of 20 fps) a static analysis adequately describes the penetration process, at least for some rocks. Hence, we will only be concerned with describing analytically the static penetration of a single wedge shaped tool. It will further be assumed that the wedge is long enough to permit a two-dimensional analysis. Numerous authors have studied the static penetration of a wedge into rock. The following papers give some of this work and provide additional references to other work. Cheatham2,3 has assumed the rock to behave plastically and has obtained force-penetration equations for both Coulomb-Mohr and parabolic yield criteria. Evans and Murrell4 have studied the penetration of two types of coal and have found equations relating the penetration characteristic (P/dSc) to wedge angle for the various strength coals tested. race&apos; attempted to find a correlation between hardness as determined by indenting the material and other mechanical properties and concluded that the results of such a test are generally inconclusive. His paper however contains a very extensive bibliography on the indenting of many different materials. Gnirk6 also has a fairly complete literature review on the static penetration of rock, of which he makes use in his indexing studies. A wide range of behavior is found in the wedge penetration of different rocks under different external conditions. For example, a rock that is essentially elastic-brittle at standard pressure may become elastic-plastic at a high confining pressure.7 It has also been observed4. " that some rocks will merely be crushed and indented by a wedge, whereas others will crack and form chips, furthermore the existence or non-existence of chips depends in great measure on the geometry of the indentor, type of rock and the depth of penetration. Hence, to attempt a theory which embraces all possible behavior is not practical at present. We, therefore, confine our attention to predicting the force-penetration characteristic and volume removal behavior for a type of rock which exhibits both crushing and chipping phases in the penetration process. Such behavior is characteristic of the harder rocks such as granites and represents a more difficult problem than the behavior of softer rocks such as coal and certain sandstones. In this preliminary study an attempt will be made to describe only the essential features of this complex penetration process. A qualitative description of these essential features is obtained with the aid of Fig. 1.1, where a wedge of vertex angle 28 is shown at some intermediate stage of the penetration process. As the wedge advances, the rock is fragmented (i.e. crushed) in some local region surrounding the wedge, the shape of this region being unknown. Simultaneous with the fragmentation in this local region, essentially elastic stresses are assumed to be building up in the surrounding rock. When a certain penetration level, di+1, is reached, the stresses along some surface are sufficient to cause failure and a chip is thus formed. The process now repeats, i.e., a crushing phase followed by the formation of a chip.

Jan 1, 1965

By W. G. Bearden, P. P. Scott, G. C. Howard

This paper concerns the rupture or breakdown of rock formations as related to drilling, completing, and stimulating production of wells, and comprises data compiled from a study of literature and records of treatment of oil and gas wells. and from tests conducted in bores drilled into rock cores and outcrops of rock. Results of the investigation indicate that the internal pressure to rupture cylinders of rock and to breakdown rock formations surrounding a bore in the earth is dependent upon the extent of intrusion of fluids. the position of bedding planes. the ratio of internal to external diameter, the tensile strength of rock, and magnitude of confining pressure, and is independent of the size of bore, degree of fluid saturation. and temperature of rock within practical limits. It is concluded that the mathematical relationship of pressure in bores and stresses in the surrounding rock must not be limited by the simplifying assumptions of homogeneity. isotropy, and impermeability; that the incidence of lost circulation of drilling fluids to induced fractures may be reduced by preventing intrusion of fluids into the small intrinsic fractures along weak bedding planes; and that the magnitude of the breakdown pressure of wells to be treated may be lowered by removal of mud cake. INTRODUCTION The purpose of this paper is to present and discuss the results of tests which may serve to broaden the understanding of the phenomena of rupture or breakdown of rock and thus contribute to the improvement of the techniques for drilling and completing wells. including such operations as preventing lost circulation, stimulating production, and placing cement. Since the early recognition of the possibility of rupturing rock adjacent to a well by fluid pressure, the distribution and magnitude of stresses around a well and the internal pressure to cause failure have been expressed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of a homogeneous. isotropic, impermeable material. In either the elastic or plastic state, if the conditions of homogeneity. isotropy, and impermeability were the normal characteristics of rock. there would be no reason to question the validity of the above principles when applied to rock. However. since most rock formations are characteristically permeable to some degree, contain bedding planes and small intrinsic fractures. and are heterogeneous, rendering invalid the assumptions of homogeneity, isotropy, and impermeability, the application of the thick-walled cylinder theories to the behavior of rock formations penetrated by a bore appears illogical. Also the failure to consider the effect of the properties of the drilling fluids, which certainly intrude in various degrees into most rock formations. is further cause for questioning the application of these principles. Even in the case of cylinders of hardened chrome-nickel steel, which would he considered relatively homogeneous isotropic. and impermeable, as compared to rock, it has been observed that the internal pressure capable of being withstood by the cylinders varied with the sizes of molecules comprising the rupturing fluid used. Because of these apparent weaknesses in the theories of the behavior of thick-walled cylinders when applied to bores in rock, and the importance of knowing the true behavior of rock under the influence of fluid pressure when planning drilling and completing procedures for wells, tests were undertaken to determine by observation the actual rupturing pressure of cylinders of rock and the effects of such variables as environmental conditions and characteristics of rock formations, fluid properties, and bore dimensions. It was intended that by these tests the validity of the thick-walled cylinder theories when applied to rock would be determined and, if found invalid, mathematical expressions would be derived for predicting stress and rupturing pressure of rock formations under various conditions. Since the derivation of mathematical expressions has been only partially completed, all of the results of the latter phase are not included in this paper. PROCEDURE The investigation was initialed with a study of the theories pertaining to the rupturing of thick-walled cylinders of homogeneous. isotropic, impermeable material and a study of the

Jan 1, 1953

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown&apos;s paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).&apos; Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

By A. K. Bhasin

A. K. Bhasin, (Development Engineer, Marcona Corp., San Francisco, Calif)-The author suggests the use of the term "consistency" for apparent viscosity and accordingly calls his viscometer a "consistometer." However, he goes on to refer to "consistency" as a combination of plastic viscosity, yield stress, and stability (p. 104, col. 2, line 6). Unfortunately, such conflicting terminology is encountered too often in rheological

Jan 1, 1973

By K. P. Sinha, J. F. Schatz, T. F. Borschel, S. Demou

Triaxial creep behavior of oil shale was investigated in the laboratory at simulated in-situ conditions. A range of temperature and stress conditions were chosen to represent those within the inter-chamber pillars of a modified in-situ retorting operation. Oil shale in grades up to 60 gallons per ton have been tested. Experimental data and a constitutive model have been presented here.

Jan 1, 1982

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By Lawrence A. Shepard, Richard H. Krock

A series of ductile, two phase W-Ni-Fe composites, sintered in the presence of a liquid phase, were tested in tension. Identical room temperature stress-strain curves were obtained for specimens containing from 80 to 92 wt pct W (58 to 75 vol pct W particles). The composites exhibited a maximum elongation of 29pct at room temperature, and 10.7 pct at 77 °K. The tungsten particles in the composite elongated by the same amount at these temperatures. Single-phase alloy specimens matching the composition of the composite matrix showed about one half the flow stress of the composites. The test results demonstrated that the mechanical properties of W-Ni-Fe composites are determined by the tungsten particles alone and are independent of matrix volume fraction or mean free path over the composition range studied. A general prediction of the plastic behavior of two-phase alloys or composites from a knowledge of the properties, size, shape, and dispersion of the individual components is not, at present, possible. The excellent theoretical and experimental exposition of the dispersion-strengthening problem applies only to cases where the stronger phase is present as fine particles and in volume fractions of a few percent. Materials in which the stronger phase constitutes a significant fraction of the volume, although of broad engineering interest, have received comparatively little analytical attention. This important group of materials is the concern of the present study. The degree of deformation of each phase during the plastic working of a ductile two-phase alloy has been established by Boas and Honeycombe,1 Clare-brough,2 and Clarebrough and berger.3 These workers empirically correlated the recrystallization temperature of the individual phases with the degree of cold work sustained by each. It was shown that the deformations of both phases are equal and therefore the same as that sustained by the composite whole when the volume fraction of the stronger phase exceeds 35 pct. At yielding, however, deformation begins in the weaker phase. A direct correlation of composite strength, as a function of deformation, with the strength of the individual components cannot be made. In the presence of stronger phase particles, the flow stress of the weaker matrix phase is enhanced by an additional hydrostatic component. The development and potential magnitude of matrix strength promotion upon straining has not even been experimentally established. Quantitative work in this field has been confined to ceramic-metal composites. These materials fracture at strains considerably below 1 pct by cracking of the ceramic particles.4-6 An indication of the potential constrained matrix strength capacity is given by the observation by Nishimatsu and Gur-land4 that the maximum tensile strength of a WC-Co composite is almost double the bulk strength of the cobalt matrix. The relationship between composite strength and geometry is ordinarily expressed in terms of the mean-free matrix path (referred to subsequently as MFP) between the stronger particles.* This factor takes into account both the volume fraction of matrix phase and the average size of the particles. unke17 concluded that composite strength varied directly with the decreasing log MFP, following the Gen-samer8 relationship. However, Gurland and ~radzil~ reported a strength maximum at an MFP of the order of 1 p in WC-Co composites. A ductile two phase metallic composite was chosen for the present investigation of composite mechanical properties with the view of avoiding the difficulties and ambiguities noted above. The W-Ni-Fe heavy alloy of Green, Jones, and pitkin9 contains 80 to 94 wt pct W, and nickel and iron in a weight ratio

Jan 1, 1963

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By E. Teghtsoonian, E. M. Schulson

The tensile behavior of bcc ordered P&apos; AuZn single crystals (CsCl structure) has been investigated under varying conditions of temperature, composition, and orientation. Between -0.2 and 0.4 T, multi-stage hardening occurs fm stoichiometric and nonstoichio-metric crystals oriented near the middle of the primary stereographic triangle. At higher and lower temperatures, parabolic type hardening occurs, followed by work - softening at the higher temperatwes. Deviations from stoichiometry give rise to increased flow stresses. Multi-stage hardening was observed for most orientations, except along the [loll-[lll] boundary and near the [001] corner of the stereo -graphic triangle, where parabolic type hardening occurs. Along two slip systems, (hk0)[001] and (, operate simultaneously while in the [001] comer, slip occurs mainly on the system. Electron microscopy of deformed crystals revealed bundles of edge dislocations forming walls approximately Perpendicular to the glide plane. In general the plasticity of 4&apos; AuZn closely resembles the plasticity of bcc crystals. In recent years, considerable interest has arisen concerning the mechanical properties of the CsCl type intermetallic compounds Ag Mg,&apos;- Fe co,&apos; and Ni Al.&apos;-&apos; The compound P&apos;AuZn is structurally similar. It has a low and congruent melting point of 725"~,&apos;" remains ordered up to the melting point,16 and pos-esses a range of solid solubility from 47.5 to 52.0 at. pct Au at room temperature.15 The present paper reports the results of an investigation on the general tensile behavior of material in single crystal form. Some dislocation configurations characteristic of the deformed state are also reported. The results of a detailed study of the slip geometry in AuZn are presented in a separate paper.17 PROCEDURE Alloy preparation, crystal growing techniques, and the procedure followed in selecting specimens of minimum composition variation are reported elsewhere.17 Dumb-bell shaped tensile specimens were prepared by carefully machining single crystals in a jewellers&apos; lathe to a gage length of 0.80 in. and diam of 0.090 in. Back-reflection Laue X-ray patterns and room temperature tensile tests revealed that machining damage could be eliminated by electrochemically polishing 0.005 in. from the machined surface followed by annealing at 300°C for 1 hr. Specimens were polished in fresh 5 pct KCN solution (40°C, 12 v). Experiments were performed by gripping specimens in a self-aligning pin-chuck and threaded collet system, then straining in a floor model Instron tensile machine. All tests were performed in duplicate. Experimental variables included temperature, composition, and orientation. Unless otherwise stated the strain rate was 2.5 x 10"3 per sec. Liquid testing environments included nitrogen (WOK), nitrogen cooled petroleum ether (133" to 293"K), and silicone oil (293" to 488°K). Resolved shear stress-shear strain curves were electronically computed from autographically recorded load-elongation curves. Stress and strain were resolved on the macroscopic noncrystallographic (hkO) [001] system operative under the specific test conditions of temperature, strain rate, and orientation reported earlier.17 RESULTS The temperature dependence of the work-hardening curves is shown in Fig. 1 for gold-rich crystals of 51.0 at. pct Au oriented near the center of the stereo-graphic triangle. Over the range of intermediate temperatures from -200" to 400°K, they are very similar to those classically observed for fcc metals (reviewed by Nabarro et al.).&apos;&apos; The beginning of deformation is characterized by a region of decreasing hardening rate, stage 0, which is followed by a region of low linear hardening, stage I, and then a region of higher linear hardening, stage 11. At the higher temperatures, stage 111 is observed, a region of decreasing hardening rate. Over the intermediate temperature range, the extent of stage 0 and of the slow transition between stages I and I1 decreases with increasing temperature. Total ductility is large, often greater than 300 pct shear. As the temperature is either increased or decreased, the extent of stage I is decreased, giving rise to parabolic type flow and reduced ductility. Similar temperature effects have been reported for bcc ~r~stals.~~-~~ Below -14O°K, hardening is terminated in brittle fracture while above -400°K. initial hardening is followed first by work-softening and then by chisel-edge type ductile fracture. Stoichiometric (50.0 at. pct Au) and Zn-rich (51.0 at. pct Zn) crystals were also tested from 77" to -500°K. The effect of composition on the flow behavior is illus-

Jan 1, 1970

By P. R. Bradley

NO thought had been given to deep level mining at the Alaska Juneau mine prior to 1930, but in that year a prospect winze was started and continued for 1000 ft. vertically below the main haulage or adit level. The point at which this winze was started was selected entirely by the prevailing physical conditions, such as proximity to established workings, convenience, and the presence overhead of a substantial pillar of dimensions sufficient to lo¬cate the sheave wheel and loading pocket. It was, therefore, with some surprise that the unusually high-grade ore found just below the collar of the winze persisted, with certain vari¬ations, to a full depth of 1000 ft. vertically. Likewise this unusually high-grade ore was found to persist on the various crosscuts driven on levels at 200-ft. vertical intervals. To be brief, this deep level work found richer ore than any yet found in the mine over like areas, and inasmuch as the area was sufficient to plan for extensive deep level mining, plans for such work were given extended consideration.

Jan 1, 1936

By R. H. Tien

Temperature distribution as well as position of the solidified front is solved by means of "heat balance integral", for the case of freezing a slab with time-dependent surface temperature. Numerical solutions for the cases of linear variation and exponential decay for surface temperature are given. Application also includes solidification of casting. An increased interest in the heat-transfer problem involving a change of phase has been developed in recent years. Practical problems include solidification of a casting, freezing and thawing of soil, ice formation, and others. Despite the importance of the topic, a literature search reveals relatively few solutions which may be extended to practical problems. Due to mathematical complexity, which comes from the nonlinearity of governing differential equations, exact analytical solutions which have been published are limited to a few cases with simple boundary conditions. Although numerical solutions of these problems have become available after highspeed digital computers were introduced, lack of simple and general methods of programming for computation makes this approach impractical. The case of the semi-infinite slab with constant surface temperature was solved in the 19th century. In honor of Neumann, who first found an analytical solution, this kind of problem is generally referred to as the Neumann solution. As has been shown in Fig. 1, the problem to be analyzed is the freezing of a semi-infinite region (x > 0) which is initially liquid at the melting temperature with the surface (x = 0) maintained at time-dependent temperature. This analysis can be applied to the study of many casting processes where most of the heat removal is essentially unidirectional. "Heat balance integral" which has been used by Goodman1 is employed in this analysis. The concept of "heat balance integral" is to define a quantity, d(t), called the thermal layer. Beyond this thermal layer, for all practical purposes, there is no heat transfer, and the region is at the equilibrium temperature. "Heat balance integral" is obtained by integrating the conduction equation with respect to the space variable over this thermal layer d(t). Choosing some plausible temperature distribution, usually a polynomial or a finite trigonometric series in the space variable, this integral equation becomes an ordinary differential equation, with time as the independent variable, which can be solved by classical methods. The thermal layer and "heat balance integral" are equivalent, respectively, to the boundary-layer thickness and the momentum integral in hydrodynamics. A modern account of Prandtl&apos;s concept of the boundary layer and von Karman&apos;s momentum integral may be found in Ref. 2. Although the problem considered here has been limited initially to uniform melting temperature, the present method is equally applicable to the case with arbitrary temperature distribution in the liquid. STATEMENT OF THE PROBLEM The physical situation and coordinate system used in the problem to be analyzed are shown in Fig. 1. Notations used are listed in the table of nomenclature. Let us assume a semi-infinite region extending over positive x, initially at the uniform melting temperature. At the surface x = 0, a time-dependent temperature, which has a numerical value

Jan 1, 1965