Search Documents

By R. G. Stickney

INTRODUCTION The Basalt Waste Isolation Project, conducted by Rockwell Hanford Operations under contract to the U.S. Department of Energy, is assessing the feasibility of the disposal of commercial radioactive spent fuel/high-level waste in deep geologic formations in basalts beneath and within the Hanford Site in southeastern Washington State. The Basalt Waste Isolation Project mission is to identify and characterize a potential geologic repository site in basalt and to develop associated facilities and technology required for the potential permanent isolation of radioactive wastes in basalt formations. In support of the Basalt Waste Isolation Project, a laboratory testing program was conducted to evaluate the performance of the Council for Scientific and Industrial Research's "Doorstopper" biaxial strain cell. To support site characterization studies and the design of repository openings, in situ stress measurements will be conducted within the reference repository horizon (~970 m). The Doorstopper is one of the instruments being considered for use in these measurements. It was selected because it requires only a small volume of work to achieve stress relief, which is important in a closely jointed basalt. Also, test durations are short, permitting a large number of measurements to be made within a given time to increase confidence in the results. Within the reference repository horizon, temperatures are expected in the range of 40º to 60°C with a humidity of up to 100%. For this testing program, test conditions were selected to closely resemble those expected within the repository horizon. The Doorstopper test, mainly developed by Leeman (1964), is a strain rosette relief method of measuring rock stress in situ. The Doorstopper consists of a four element, 45º strain gage rosette

Jan 1, 1984

By Meng-Cherng Sun, Fun-Den Wang, David M. Ropchan

A proposed technique for improving coal-mine roof stability by softening parts of coal pillars along the sides of entries developed from structural analysis is presented. This technique is based on the transference of the high stress concentration in the roof near the upper corners of a rectangular opening to the roof rock and coal over the solid away from the opening. This transferral is accomplished by softening parts of the coal pillars by drilling a series of parallel holes into the coal in the ribs and face of the entry prior to advance. The effectiveness of the pillar softening in terms of reducing the opening width (so that the stress in the roof near the corner is equivalent to that of a narrower opening) ranges from 3 to 5 ft for a 16-ft entry using a series of 4 to 5-ft-deep parallel drill holes of 3 to 6-in.-diam on a 1 to 2-ft spacing for a particular geology. Pillar softening should be highly effective in controlling roof where cutter-roof cave conditions exist, because this technique reduces the high stress concentration in the roof at the upper corners of the opening. It may also be effective for reducing tensile roof failure and coal rib sloughing for certain specific geological conditions. This technique appears to be a simple, effective, and practical method that can be used to supplement conventional roof support methods of roof bolting, timbering, roof truss, and other existing methods in underground coal mines. The authors consider the technique feasible and believe that it merits underground trials.

Jan 1, 1975

By W. Rostoker, H. Nichols

The embrittlement by mercury of aluminum alloys in various states of anneal, cold work, and aging has been studied. It is shown that single phase and non-precipitation hardened structures irrespective of de,pee of prior cold work demonstrate some small measure of yielding before fracture occurs. Sub-yield-stress failure is confined to the aged state, and embrittlement is accentuated by small plastic prestrains. With large plastic pyestrains, embrittle~nent is progressively reduced. In previous work' it was shown that the propensity of commercial aluminum alloys for embrittlement when wetted with mercury seems to be related primarily to the intrinsic strength in the normal un-wetted condition. The data from a large number of commercial alloys in various states of anneal, cold work, and/or aging gave a generalized relationship. At low strength levels, the wetted fracture strength increases proportionately to the increase in tensile strength; but above 65,000 psi normal ultimate strength, the trend is abruptly reversed, and the wetted fracture stress decreases proportionately to the increase in tensile strength. This paper will demonstrate that the simple character of this relationship between normal tensile strength and wetted fracture strength is fortuitous. It will be shown that structure and thermal-mechanical history are clearly relevant factors. The term brittle fracture has been used to connote the geometry of the fracture surface (transverse vs shear plane) or the negligible extent of preceding plastic strain. At its maximum effectiveness, liquid metal embrittlement can satisfy both criteria—fracture transverse to the axis of tension and without observable plastic strain. In this paper, brittle fracture will signify failure at stresses below the engi-

Jan 1, 1962

By Leo L. Van Sambeek

An understanding of the creep and yield behavior of salt is required for the rock mechanics design aspects of solution mining. Most previous studies of salt behavior have been performed on small specimens of salt under homogeneous stress conditions; i.e., uniaxial and triaxial tests on specimens <0.002 m3. The corejacking test is a larger scale test (-0.75 m3) with inhomogeneous stress conditions that provides data on the structural response of salt. Interpretation of the responses from eight such corejacking tests provides verification of the requisite constitutive parameters required to predict salt behavior at different levels of stress and temperature. These constitutive parameters are not those studied in the usual laboratory test. Corejacking test results show almost inseparable elastic and plastic closures simultaneous with the corejack pressurization. Very rapid closure (on a relative basis) continues for a period of time after the pressurization. This rapid closure is shown to be both continuing yield deformation and creep deformation. After the period of rapid closure, the closure rate approaches a constant value. Numerical modeling of the corejack tests using a creep law containing both transient and steady-state creep functions does not provide results that agree with the responses measured in the corejack tests. Using an experimental design technique plus additional numerical modeling that includes yielding of the salt, results in identification of the significant parameters which allow agreement. The significance of the results from the study is demonstrated by comparing the postulated stability and creep response of a solution-mined cavern using the previous understanding of salt behavior and the understanding developed from this study.

Jan 1, 1985

By Leonard E. Wood, Yeghishe M. Avedissian

Knowledge of the basic properties of rocks-strength, structure, and permeability-is prerequisite for the success of foundation work for masonry dams, large bridge piers, and tunneling as well as for excavation in rock and special underground construction. Strength of engineering materials depends upon texture and structure as well as the environmental conditions to which they have been subjected. Failure in its widest sense implies the transition of a material from elastic to plastic state (yield strength), from continuous to discontinuous state (rupture strength). The compressive strength of a material such as rock is the stress at which a sample, loaded and unconfined at the sides, fails by rupture. Some of the external factors that control strength of rocks are the nature and type of stress, whether uniaxial or triaxial, compression, tension, or torsion. Another important factor is the rate of stressing-whether constant, impact, or gradually increasing. Of the internal factors, the effect of texture upon strength is obvious. Generally, fine-grained rocks have higher compressive strength than coarse-grained prototypes. Among metamorphic and igneous rocks those with better and higher degree of interlocking of their crystals are generally stronger than the ones with poor or lower degree of interlocking. In sedimentary rocks, the degree and type of cementation has a great influence upon their strength. Structurally, the existence of fissures, cracks, and seams of argillaceous or organic materials in a rock specimen will greatly reduce its strength. Because most rocks are characterized by bedding planes, laminations, or foliations, they are anisotropic in their physical properties and hence compressive strength depends on the orientation of the bedding planes to

Jan 1, 1972

By Richard F. Miller, W. E. Milligan

Work was undertaken two years ago at the Hammond Laboratory for the purpose of determining the magnitude of the elastic range in single crystals of pure metals by means of creep tests, the assumption being made that if a true elastic range exists, the elastic limit represents the maximum stress for no creep. A sensitive extensometer was constructed, and creep tests were made on zinc single crystals at a variety of loads and temperatures1. It was soon discovered that there is no measurable elastic limit in ductile zinc single crystals at, or above, room temperature. The inference that pure metallic single crystals may not possess a definite elastic range was not justified, however, since zinc had been tested in creep only above its recrystallization temperature, and several investigator2,3,4 had already shown that above the recrystallization temperature polycrystalline metals will flow under very small stresses, while below that temperature stresses of a much larger magnitude are required. For that reason, it was decided to extend the study of the elastic limit to other metals having a higher recrystallization temperature than zinc. Aluminum and silver were selected, because of the ease of obtaining pure materials and of preparing large single crystals, and because the crystallo-graphic glide system of these metals is well known. Owing to the limited time available, the elastic range was investigated by slow tensile tests rather than by creep tests. Production of Specimens A luminum Recrystallized single crystals were prepared from 99.95 per cent aluminum supplied by the Aluminum Company of America. The ingots were melted in an Acheson graphite crucible in a gas furnace, and cast

Jan 1, 1937

By Michael A. Devane, Neil Duncan

Inclines and tunnels can extend from ground surface to considerable depths traversing a wide range of lithologies. The strata encountered may be affected by loosening and induced stresses at different locations along the route. It is suggested that Phase I of the pre- driving assessment process should include study of the geology, hydrogeology, rock material and rock mass characteristics. A rock mass disruption factor is used to express the ratio of the unconfined strength of intact rock material to the unconfined strength of in situ rock mass. It is suggested that there is a relationship between in situ (secondary) permeability values and the disruption factor, since the permeability of the rock mass is governed by parameters which influence strength. In Phase I1 of the pre-driving assessment, consideration should be given to the prediction of primary loosening which results largely from disturbances to the rock mass arising from the driving process. Also in Phase 11, preliminary assessments are made of the effects of induced stresses and of the geodurability characteristics of the rocks. In Phase 111, the mechanics of various secondary loosening pro- cesses are considered along with their relevance to estimates of stand up time and support requirements. Yield-line analysis is introduced for the study of plastic and brittle type bending deformations. Stand up time and support characteristics are also assessed. In Phase IV, the effects of induced stresses are analysed. It is suggested that even for broken rock in the Yield Zone, the rock mass disruption factor may not often increase above lo which is equivalent to an in situ permeability of 10-1 m/s.

Jan 1, 1983

By Harry A. Lipsitt, Attwell M. Adair

A number of papers have appeared in the past several years concerning the nature of the fatigue limit. The hypotheses presented in those papers fall into three groups. Some authors attribute the fatigue limit to the distribution of interstitials prior to testing (static group). Others consider the fatigue limit to be due to dislocation-interstitial reactions during testing (dynamic group). Still other propose that the fatigue limit results from a characteristic peculiar to the iron (bee) lattice (inherent group). This communication is an attempt to digest the salient features of each of the hypotheses, discuss them, and present some constructive criticism. It is shown that each of the extant ideas has some merit, and that each of the mechanisms thus far proposed is necessary, but individually insufficient, to provide the desired level of understanding of the fatigue-limit behavior of metals. Static Group. The data of Oates and wilson1 on finegrained (=0.022 mm diam) low-carbon steel indicate that the fatigue limit exists in the absence of sufficient plastic deformation for any dynamic strain-aging mechanism to be operative. Specimens tested just below the fatigue limit showed yield-point behavior typical for unstrained material when removed from the fatigue machine and tested in tension. These results led them to the conclusion that initial dislocation locking controls the fatigue limit in this material, which has a yield stress higher than the fatigue-limit stress. Prestraining this material just prior to fatigue testing would be expected to lower the fatigue-limit stress; this they observed experimentally. Yoshikawa and sugeno2 are of the opinion that the sharp fatigue limit in fine-grained iron is caused by

Jan 1, 1967

United Engineering Trustees, Inc. GEORGE D. BARRON ARTHUR S. DWIGHT R. M. ROOSEVELT The Engineering Foundation H. C. BELLINGER E. DEGOLYER J. V. N. DORR

Jan 1, 1932

By R. A. Graham, R. W. Rohde

The effect of hydrostatic pressure upon the austenite start temperature of a commercial Fe-28.4 at. pct Ni-0.5 at. pct C alloy has been determined. For pressures to 20 kbar, the austenite start temperature decreased from its atmospheric pressure value of 380°C at the rate of about 4°C per kbar. These data are analyzed by two different thermodynamic approaches; first, considering the transformation as an isothermal process, and second, considering the transformation as an isentropic process. It was found that both these approaches fit the experimental data equally well. The effect of hydrostatic pressure upon the austenite start temperature is best described by considering the mechanical work done during the transformation as that work obtained by multiplying the applied pressure with the gross volume change of the transformation. It is widely recognized1 that strain has an important effect on the initiation of martensitic transformations.* For example, the martensite start tempera- *In this paper, use of the term martensitic transformation implies the reversal of martensite to austenite as wen as the formation of martensite from austenite. ture, M,, may be increased by plastic deformation. Similarly, plastic deformation is observed to lower the austenite start temperature, A,. The effect of uniaxial stress on the M, of iron-nickel alloys has been studied by Kulin, Cohen, and Averbach.2 They found that the martensite start temperature was significantly changed by stresses well within the elastic region. Moreover, the effect of tensile and compres-sive stresses differed. These effects were explained in terms of the interaction of the applied stress with both the dilational and shear components of the transformation strain. The magnitudes of the influence of uniaxial tension, compression and hydrostatic pressure on Ms were measured in 30 pct Ni 70 pct Fe by Pate1 and Cohen.3 Their thermodynamic calculations and similar calculations by Fisher and Turnbull4 predicted the experimental results when the transformation was assumed to occur isothermally at some fixed driving force. This driving force was assumed to be supplied by a combination of the chemical free energy difference between the austenitic and martensitic phases and the work performed during transformation by the applied stress. More recently, Russell and winchel15 reported the effect of rapidly applied shear stress on the reversal of martensite to austenite in iron-nickel-carbon alloys. They performed a thermodynamic analysis of this transformation based upon the assumption that the re- versal occurred adiabatically. They concluded that the applied shear stress did not significantly interact with the transformation strain and thus did not assist in inducing the reversal. Rather they concluded that the reversal was effected by localized strain heating which resulted from the gross local shear deformation of the experiment. In either the adiabatic or isothermal analysis it is necessary to compute the work performed by the interaction of the applied stress and the transformation strains. In the case of hydrostatic pressure this interaction has been treated by two different methods. In either case the applied pressure is assumed to remain constant during the transformation. In one treatment the applied pressure is assumed to interact directly with the dilatational strain associated with the formation of an individual martensite plate.3&apos;4 This local strain has been measured at atmospheric pressure in iron-nickel alloys by Machlin and Cohen.6 In the above treatment this local strain is assumed invariant with temperature and pressure changes. In the other treatment the applied pressure is assumed to interact with the gross volume change of the transformation.7,8 The usefulness of this latter treatment has been demonstrated by Kaufman, Leyenaar, and Harvey7 who calculated the effects of pressure upon the martensite and austenite start temperatures of Fe-10 at. pct Ni and Fe-25 at. pct Ni alloys. Excellent agreement was obtained between their calculations and their experimental data on an Fe-9.5 at. pct Ni alloy. However, this treatment suffers from the fact that the data required to calculate the volume change of the transformation (i.e., the initial specific volumes, the thermal expansion and compressibility data for both the austenitic and martensitic phases) is, in general, not available for any material except pure iron. Thus the calculations of Kaufman et al.7 were necessarily performed by assuming that the volume change of the martensitic transformation in the iron-nickel alloys was that same volume change occurring during the a-? transformation in pure iron. While this approximation may suffice for very dilute alloys it is likely to be inaccurate in high nickel alloys. We have performed measurements of the effect of hydrostatic pressure to 20 kbar on the A, temperature of an Fe-28.4 at. pct Ni-0.5 at. pct C alloy. The composition is similar to the alloy used by Pate1 and Cohen3 to determine the effect of pressure upon the M, temperature. The present measurements permit calculation of the interaction between the applied pressure and the transformation strain. Additionally, measurements have been made which allow precise determination of the gross volume change of the transformation. The data allow direct comparison between the alternate hypotheses of the interaction between the applied pressure and a dilatational transformation strain characterized by either the formation

Jan 1, 1970

By R. R. Spencer, C. A. Campbell, R. J. Marcotte, A. S. Kromer, P. H. Ostlender

Calumet Div. of Calumet & Hecla Inc. is engaged primarily in mining, milling, and smelting the native copper ores of northern Michigan. The copper occurs in fragmental tops of lava flows and in certain interbedded felsitic conglomerates of Pre- Cambrian age. The most famous native copper ore- body in world history is the Calumet conglomerate, which outcrops between the villages of Calumet and Laurium for a distance of about 2 miles. The Osceola lode parallels the conglomerate lode and is mineralized for about 3 miles. Horizontal distance between the two is 750 ft. In 1932 the price of copper dropped to 54 per lb. Coupled with the high cost of obtaining copper from extreme depths, this low price made the venture un- profitable, and the mining unit was abandoned. After the shaft pillar copper was removed from several of the conglomerate shafts in a retreating operation, the mine was allowed to fill with water. In post-depression years, when the price of copper stabilized at about 12¢, Calumet Div. found it profitable to operate its remaining mines on other lodes, as well as its tailings reclamation plants.

Apr 1, 1956

By K. R. Carson, J. Weertman

THE fatigue-hardening curve has received much attention in recent years. This curve is obtained by plotting the peak stress required to maintain a given plastic strain per cycle vs the number of cycles. It

Jan 1, 1969

THE committee in charge of arrangements for the meeting of the Institute in September has com-pleted its program. The headquarters of the meeting will be at the Palace Hotel, San Francisco, and the registration committee will be at the hotel all day on Sunday, Sept. 24, and from 8 a.m. until noon on Monday. On Sunday afternoon, automobiles will be available for sightseeing trips around the city. Monday will be devoted to technical sessions. In the morning, there will be sessions on Mining and on Iron and Steel; in the afternoon, sessions on Mining and Milling. At these sessions, in addition to the papers mentioned in the tentative list printed in August, there will be presented three papers on the geology, mining and milling of the Comstock lode; one on the Aztec mine, Baldy, N. M.; one on the Colombian oil fields; and one on charcoal precipitation of cyanide solutions. The luncheon on that day will be Dutch Treat, for men only, at the Engineers Club. On Monday evening, there will be an informal buffet supper at the home of F. W. Bradley. On Tuesday morning, a party of 50 men will leave for Hetch Hetchy. During the four days of the trip, the party will see the Priest tunnel and earth dam under construction by steam-shovel and hydraulic-fill methods, the Big Creek shaft and tunnel, early intake power plant and tunnels and the Hetch Hetchy dam under construction. For those who remain in San Francisco, Tuesday will be "San Francisco Day." There will be motor trips to the Presidio, Cliff House, Golden Gate Park, and other points of interest, and shopping trips to Chinatown. On Wednesday, "University of California Day," the party will be guided through the university by members of the Mining Association, the affiliated stu-dent society, and will see the Greak Theatre and not-able buildings. Thursday will be "Leland Standford, Jr. University Day." Automobiles will leave the Palace Hotel at 10 a.m., and will return from the university at 4.30 p.m. Friday has been reserved for trips to the Selby Smelter, to Mt. Tamalpais, or to other points of interest. Arrangements will be made to visit the mines or gold dredges in California, if members desire to do so, but such trips must of necessity be considered special trips and arrangements will have to be made to suit the convenience of the individual or party. The Golf Committee will make arrangements for those who wish to play golf.

Jan 9, 1922

By W. O. Hotchkiss

RECOVERY and profits in the mining business do not go hand in hand. Some part of an orebody can usually be recovered at a lower cost per ton than the whole orebody or a higher proportion of it. Similarly, the total of the profits that may be made from mining an orebody is in itself not a true measure of the value of the business. The yardstick for money value should be present worth, and this is particularly so for purposes of com-parison. A simple example, well within the bounds of practicability, illustrates these points: Assume a mine to have known ore reserves of 4,000,000 tons. The ore is of uniform grade but is so situated that 1,000,000 tons could be mined more cheaply than the remainder. Present operations are on the basis of complete recovery of the ores. Output is 100,000 tons per year at a profit of $1 per ton. It is estimated that the 1,000,000 tons of readily accessible ore could be mined at the same production rate but at a profit of $2 per ton. For an output of 100,000 tons each year at a profit of $1.00 per ton, the mine will have a life of 40 years; will produce $4,000,000 of total profit, and, at Hoskold rates of 8 and 4 per cent, will have a present value of $1,104,690. If only the easy one-quarter of the ore is considered, with an output of 100,000 tons each year, at a profit of $2.00 per ton, that part of the mine will have a life of 10 years, will produce total profits of $2,000,000, and at rates of 8 and 4 per cent will have a present value of $1,224,800. . Under conditions such as these, then, one-quarter of the reserve ore promptly mined is worth some 10 per cent more than the entire reserve would be on an average basis extending over the longer period. Assume further that one-half, or 2,000,000 tons, of the reserves could be promptly mined at the same yearly rate of 100,000 tons at a profit of $1.50 per ton. Then this part of the mine would have a life of 20 years, would produce total profits of $3,000,000, and would have a present value of $1,320,630; approximately 20 per cent greater than for the whole ore-body on an average basis for the longer period.

Jan 1, 1936

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley&apos;s paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley&apos;s formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881

By P. R. Hanes

A description of the methods used in driving two tunnels, 2 miles long each, one a 9-ft. and the other a 19-ft. diameter section, for the Owyhee Irrigation Project, Oregon. One heading of the smaller tunnel was driven 1315 ft. in 73 shifts in one month and 10,966 ft. of this section completed in ll½ months using two shifts for eight months and three shifts the rest of the time. This is a good illustration of the proper use of a mechanical shovel and the importance of careful selection of supplernentary equipment to secure best results. Large cars, speedier and heavier locomotives, 36-in. gage track of 45-lb. rail, and a good switching method increased actual shoveling time and cut down muck removal period about 45 minutes from average. The larger tunnel, after trying out standard electric revolving shovels of both the rail mounting and caterpillar tread types, was excavated with a mechanical mucker. This is the first time that a tunnel of so large a section has been handled this way. This record work was accomplished without drill carriages.

Jan 1, 1934

Masjid-i-Sulaiman Field.—During the past year, drilling activities have been limited to repair work. No new developments of importance can be recorded in production technique. Fall of dome pressure is maintained at the 1 lb. per sq. in. per annum rate mentioned in previous reports. Acid treatment of wells is being increasingly used and for wells in fissured areas has been very successful. Such wells have been converted into first-grade producers with substantial drops in bottom-hole differential pressures. The effect of acid treatment has been to increase the flowing lives of wells so treated. The normal procedure consists of threo treatments of 500 gal. commercial acid diluted 100 per cent but success has been met with fewer applications. The policy of returning products to the resorvoir has been continued. The total quantity of products returned since the policy was commenced in 1929 now amounts to approximately 30 million barrels. Haft Kel Field.—The drilling of the main Haft Kel structure for production purposes has now been completed. Production and control wells have been completed to meet the rate of production anticipated over the next few years.

Jan 1, 1937

I. N. KNAPP, Ardmore, Pa. (written discussion*).-Captain Lucas has made an important contribution to our, knowledge of Belle Isle, especially as to the outline of the sulphur deposit, and the pronounced irregularity of the salt surface. I agree with his view, that the elevation or mound that constitutes Belle Isle may consist of several salt domes formed at different periods. It may be interesting to note the high gas pressure encountered in pockets in the salt by my No. 1 Belle-Isle well. While drilling a dry hole with cable tools, we sometimes struck. pockets of gas which would float the tools, so that drilling had to be suspended sometimes for several hours at a time, until the head of gas was exhausted, and this with a string of tools, 5-in. (127 mm.) stem 36 ft. (10.9 m.) long, that weighed complete about 3500 lb. (1587 kg.). At about 1800 ft. (548 m.), we struck the largest gas pocket and the string of tools was thrown up and nearly out of the hole. When it dropped back it made several loops

Jan 1, 1918

By W. M. Morris

THE volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrell1 measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0° to 130° F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70° to 250° F. The specific volume in the gas and liquid region was determined at pressures up to 3000 lb. per sq. in. ? throughout this temperature interval. In addition, the vapor pressures were measured at 30° intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0° and 250° F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100° and 460° F. was carried out with apparatus that has been described in another paper (A.I.M.E. Tech. Pub. 1127).

Jan 1, 1939

By Arthur F. Taggart

The following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.&apos; Screen apertures used are the average apertures of testing screeps of the meshes given. i . Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill, Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversise reground in pebble mill, see Card 113. Feed to mill through 2-in. mesh. Mesh Feed, Per Cent. Discharge, Per Cent.. + 1in. 5.50 ....... + 3/4. 28.00 + in. 30.00 ...... + 1/4in. 19.72 ....... + 10 10.87 2.10 + 20 2.42 8.00 -20 3.51 .....,. + 40 ....... 22.68 + 60 ...___ 10.50 4-80 ....... 11.80 + 100 ....... 3.90 -100 ....... 40.15

Jan 1, 1916