Search Documents

By Carl Heinrich

I HAVE read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: Horn Silver Slags Oxygen(b) Oxygen(b) Average of I and. II Slag I percentage Slag II percentage Oxygen Si02 33.9 18.1 .35.0 18.7 34.50 18.40 FeO 26.8 6.0 25.4 5.7 26.10 5.80 CaO 26.1 7.5 24.9 7.1 25.50 7.30 BaO 3.2 (a) 0.3 3.2 0.3 3.20 0.30 A1203 10.8 5.1 9.3 4.4. 10.05 4.75 100.8 37.0 97.8 36.2

Jan 10, 1916

By N. Brown

From the theories of flow and fracture it is shown that the difference in reciprocals of the transition temperatures (OK) is a quantitative measure of temper ernbrittlement. Experimental data are given which support this conclusion. STUDIES of temper embrittlement have been made with various viewpoints; some involved a study of the kinetics of the reaction,',2'" others were concerned with changes in the mechanical properties," . and still others investigated the structural differences between the embrittled and unembrittled states by means of the microscope," -ray ,' measurements of electrode potential," and electrical resistivity." In all these studies, the difference in impact properties was the criterion for distinguishing between the embrittled and unembrittled states. By common agreement the difference in transition temperatures is now taken as a measure of the degree of embrittlement, and this measure is used as the quantitative measure upon which studies of the phenomenon are based. Vidal and Jolivet"' suggested that the degree of embrittlement was the same whether measured by impact or by a slow bend test. Their conclusion was based on tests at constant temperature. Jaffe and Buffum" using the impact and slow bend test showed that, for a given degree of embrittlement, the difference in transition temperatures varied with the method of testing. Hultgren and Chang" showed that the difference in transition temperature produced by the V-notched Charpy impact test was not the same as the value produced by the keyhole-notched impact test. This is a very fundamental point because there can be no true measure of temper embrittlement unless it is invariant with respect to the test method. Theory The purpose of this analysis is to show how the transition temperature depends on the stress distribution and the state of the material. The criterion for fracture may be stated as follws: where iF is some function of the principle stresses and F is a critical condition depending on the state of the metal. Similarly yielding occurs when Where is another function of the prin-ciple stresses and Y is a critical value depending on the state of the material. There is some controversy as to the exact form of the function f,.(u,, u,, us) but most experimental data give the following criterion:= where 8, and 6, = 21 or 0. Combinations of 6, and 8, give the various criteria such as the normal stress, the hydrostatic tension, and the maximum shear stress laws. Agreement is general that the octahedral shear stress law adequately describes the yield condition. where the bracketed factor will be called the design factor and depends on the stress distribution. Whether the metal decides to yield or fracture is given by the condition that The effect of temperature and strain rate upon Y has been studied by various investigators, It has been shown by MacGregor and Fisher" that

Jan 1, 1955

By Robert Bell

THE " Tar-Sands." is the name which has been given to the extensive horizontal deposit of fine Cretaceous sand, blackened by tarry petroleum, which forms the banks of the last or lowest 130 miles of the Athabasca river before it terminates in Athabasca lake. The Cretaceous strata, to which these sands belong, extend northwesterly from Dakota all the way to this lake and for 500 miles beyond it. The Athabasca river forms the uppermost section of the Athabasca-Mackenzie, one of the great rivers of the world. It rises on the Pacific side of the Rocky mountains, westward of Edmonton, and flows north of east to a point called Athabasca. Landing, 100 miles north of Edmonton, where it turns northward and runs about 280 miles before it falls into the west end of Athabasca lake. The section of this river-system which discharges the lake just named into Great Slave lake, is called Slave river, and below the latter lake it becomes the Mackenzie river. Along the section of 280 miles of the Athabasca river above mentioned, the Cretaceous strata consist of bluish-gray and drab-gray marls, on top, from Athabasca Landing to Drowned rapid, 110 miles down stream; then heavily bedded gray sandstones, 225 ft. in greatest thickness, underlying these, form the banks for about 40 miles further. The strata appear to be horizontal, but they really clip very slightly to the southward. At Drowned rapid, we see the first of the tar-sands resting on almost horizontal beds of bluish-gray limestone of Devonian age. In some places the limestone is associated with shaly or marly bands. Notwithstanding the great hiatus between the two series, the horizontal tar-sands lie conformably upon the almost level upper beds of the limestone wherever the two formations are seen together, all along the river, throughout a

Mar 1, 1908

Seattle offered sunny, dry weather to about 2500 mining men who assembled September 10 to 14 for the 1961 American Mining Congress. The impact of snappy sessions on national mineral policy, state of the industry and foreign competition (to name only a few) was somewhat overshadowed by enthusiasm of conventioners for salmon fishing. This lordly fish, which mysteriously runs to its hatching place to spawn and die at this time of year, was not cooperating with the anglers in Puget Sound. However, this did not prevent consuming ample amounts of the deliciously prepared Quinault salmon at the "Potlatch" celebration.

Jan 10, 1961

By F. J. Radd, R. L. McGlasson

The mechanisms of corrosion and corrosion fatigue damages to sucker rods are examined from a fundamental electrochemical viewpoint, and the relationships of sucker rod microstructures to these damaging effects are defined. The common corrosive agents in crude oil production and storage are discussed as to types of attacks that they cause. The variations of fatigue strength with alloy content, surface preparation, and stress ranges are analyzed. Finally, conclusions are drawn as to how microstructures largely influence and control sucker rod performance. INTRODUCTION Greater than 90 per cent of the crude oil produced by artificial lift methods is produced through sucker rod pumping systems. In the USA each year more than $14 million is spent for sucker rods in new and old pumping installations. It is important to make this investment a wise one. Essentially, the sucker rod system is a long series of steel rods, operating under alternating stress loadings and under mechanical vibrations, which connect the surface power source with the subsurface pump. These rods often operate in a variety of corrosive media, including water, brines, carbon dioxide, hydrogen sul-fide, and air. Basically, this paper is concerned with the problem of the behavior of certain steels in various corrosive media under high and dynamic stress patterns. The main objective of this paper is to show how, once the stress effects and the corrosive environments are defined, one can still realize structural control and beneficial influence upon corrosion and corrosion fatigue. FUNDAMENTAL DEFINITIONS AND ANALYSIS In the corrosion and stress behavior of this solid state mixture of iron and iron carbide called steel, one must analyze upon what major factors does its service life depend and of what, exactly, is steel composed. The former question can be referred to two external factors and two internal factors. The two major external factors are: 1. the nature of the stress patterns — size and range of stresses present 2. the nature of the corrosion — erosion environment — the corrodent and/or wear involved The two fundamental internal factors that govern the strength and useful life of a steel both in normal duty and in heavy-duty corrosion service are: 1. the nature of the steel volume properties 2. the nature of the steel surface properties For the latter question normal steel is defined as a solid mixture of iron and iron carbide particles, generally with certain accidental and intentional elements present. (The amount of iron carbide present is determined by the carbon content of the steel.) These additional elements generally dissolve into either the iron (ferrite) or the iron carbide (cementite) components.

Jan 1, 1955

By James R. Aggson, John C. Curran

In a cooperative research effort, the US Bureau of Mines Denver Mining Research Center and the Pittston Co. investigated floor heave ground control problems that have plagued underground coal mining of the Beckley coalbed in southern West Virginia. Floor heave is accompanied by a redistribution of stresses and loads that are associated with underground openings, causing roof and pillar problems. The floor and roof analysis techniques that were used in the USBM/Pittston investigation may have a wide range of applicability in the mining industry. Recommended orientations and geometries for mining operations are directed at floor problems, but may also enhance roof stability.

Jan 1, 1980

By E. D. Gardner

FIFTY years ago the Utah Copper enterprise at Bingham was just getting under way. An epic in metal mining was in the making. Throughout the West the bonanza deposits were approaching exhaustion and most ore still went direct to smelter. But concentrators were shortly to be constructed for treating milling grade ores, and most important, the pilot plant for the Utah Copper enterprise was being built that year at the mouth of Bingham Canyon. The same decade was to see development at the Inspiration mine in Arizona of the most important new mining method for 50 years to come—undercut block caving. Although the average grade of ore being mined has been declining for 50 years, and wage rates and prices of supplies have been greatly increased, the mining industry has continued to grow and to prosper. Technology has advanced to a point where minerals can be mined under the most severe conditions. The hardest rock can be drilled and broken and the heaviest ground handled. Large or small, an ore-body can be mined successfully, at any desired rate of production. It is possible to pump great volumes of water and to ventilate the most extensive workings; air conditioning has made practicable the mining of ore where the rock temperatures are beyond those that can be borne by man. Mining today in the U. S. is a huge earth-moving operation. In 1953 nearly 2 billion tons of material were mined for direct use or for processing. Stripping at open-cut mines totaled about 1.7 billion cu yd. Table I gives relative tonnages of the branches of the mineral industry in 1953. In addition to the solid materials moved, 350 million tons of petroleum and 340,000 tons of gas were produced in 1953. Fifteen million tons of salt and 5 million tons of liquid sulphur were pumped from wells. An appreciable amount of copper was recovered by leaching old mine workings and dumps. Total value of minerals produced in 1953 was $14.4 billion: oil and gas $7.6 billion, coal $2.6 billion, nonmetallics $2.4 billion, and metals $1.8 billion. Formidable problems face some branches of the industry today, especially pertaining to increased output tons per manshift. The time has come when these problems should be reappraised. With current wage rates, the industry no longer can afford to pay men to do manual labor. It should be recognized, also, that the miner is a skilled worker; efforts to promote the dignity of his calling and his pride of accomplishment have yielded beneficial results. Mineral deposits occur under widely varying conditions. In most instances the degree of support needed by the roof and walls is the deciding factor in selection of an underground mining method. The degree of support needed, in turn, is governed by natural physical characteristics of the ore and its enclosing rocks. Mine operators, of course, learn to judge ground by observation, and an experienced mine boss generally can anticipate what will happen following any given mining operation. A more scientific approach, however, would be advantageous in most cases. More should be known about the strength of the ore and the enclosing rocks, more about stresses set up in the ground when ore is removed, and more about the mechanics of moving ground. Better understanding would work both ways: first, favorable rock conditions could be fully utilized for more efficient mining, and second, hazards of rock falls could be minimized, loss of ore in mining reduced, and expenses caused by ground pressures and subsidence lowered. In general, mining comprises breaking the ore or rock in place, supporting the mine workings, and transporting the ore to the surface. This latter is a materials handling problem. Ventilation, of course, must be provided, and the mines must be kept free of water. Development work at some places is the most important cost item in extracting ore. Drilling and blasting remain the usual practice for breaking ore or rock from place except, of course, at block-caving mines. The drilling and blasting practice at a mine must fit the mining method. In laying out mining procedures attention is being given to

Jan 1, 1956

By Allen H. Rogers

THE need for coordinated effort on public problem by engineers has long been felt. Early in June there will assemble in Washington a conference composed of delegates from all the engineering organizations in the country. The call for this conference is issued by the Joint Conference , Committee of the four national societies as the completion of its work on the organization of a congress composed of delegates representing all the engineering organizations of the United States. The plan for this confederation was presented at a joint meeting of the administrative boards of the national founder societies on Jan. 23, 1920; and was unanimously approved in principle by that meeting. The work of the committee since that date has consisted in drafting a constitution of the organization to be presented at the conference for discussion and, after such amendments as may be adopted, acceptance.

Jan 1, 1920

By J. Kent Smith

VANADIUM is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal there from with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improvement of steel has been proved by rigorous scientific investigation.

Sep 1, 1907

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

By T. L. Joseph

S. T. Killian (Johnstown, Pa.)—This is one of the finest papers I have read. Tying in stoichiometric calculations with furnace performance and practice is a step which had to be taken sooner or later. The noteworthy difference between Dr. Joseph's type of calculations and regular blast furnace calculations is that the Ib mol system is used as a basis. With the Ib mol system, weights, volumes, and chemical reactions can all be expressed in the same equation. In the paper, wind, ore, flux, and fuel are all expressed as lb or lb mols. Probably Dr. Joseph does not realize it, but the vague word coke appears only twice in the entire paper. Lb of C and Ib mols of C are followed through reactions but the word coke appears only as 1560 lb coke per ton of pig and 1700 lb of coke per ton of iron. Obviously in order to understand furnace reactions, the coke should be expressed as lb or lb mols of C. Furnaces can also be compared more easily. In some respects the paper is too thorough and too complete. The effects of the metalloids reduced into the iron upon the top gases represents a difference of less than 3 pct of the CO formed in the bosh. Due to the completeness of the calculations in relation to the CO/CO2 ratio, this was included and was necessary. However, the exclusion might have enabled more furnace men to follow the lb mol system of calculations through the blast furnace to a better degree. By considering only irons of similar analysis, this part of the calculations might have been omitted. However, if this had been done, total rewriting of the paper later would have been necessary in order to make the work complete as it is now. It also would not have been nearly as authoritative. In the paper, there appears the reaction: H2O + CO ? CO2 + H2 [I] Dr. Joseph states that he did not take this reaction into consideration in any calculations pertaining directly to the paper. The piobable reason- for this is that although it contains all the main reacting top gases except N2, it is rather inflexible since it is monomolecular in relation to each of the reacting gases and does not tie in with the gasification of C. Actually the reactions: H2O + C ? CO + H2 [2] 2H2O + C ? CO2 + H2 [31 and the solution loss reaction: CO2 + c ? 2c0 [41 tend to assume an equilibrium through the reaction: H2O + CO ? CO2 + H2 [I] which should be considered a balancing or equilibrium reaction. Reactions 2, 3 and 4 permit furnace conditions to balance with the CO/CO2 ratio and H2 formation. They tie in with the solution loss. Reaction 1 unites them chemically. Probably the best calculation to make at this time would be to try to find the relative importance of the CO2 from the flux and the H2 in the dilution on an actual furnace gas analysis. For this purpose the Dob-scha-Carnegie-Illinois paper—"Effect of Sized and Sintered Mesabi Iron Ores On Blast Furnace Performance" is chosen. This paper was presented before the blast furnace section of the AIME in 1948. This represents the best large scale furnace operation available to me. Unfortunately the changes were brought about by beneficiation of the burden and not by changes on one burden. In choosing the basis for the calculation in relation to the furnace, 100 mols of dry top sgas is chosen. This leaves something to be desired inasmuch as the nitrogen basis is changing but I believe it will be better understood than any other type and it is the easiest to use.

Jan 1, 1952

By W. J. Babyak

The habit planes for hydride precipitation in large grains of alpha zirconium and Zircaloy-4 were determined in specimens containing 161 and 136 ppm hydrogen, respectively. In zirconium, the hydride platelets precipitated on various pyramidal planes inclined to the basal plane at angles ranging from 10 to 50 deg and 75 to 90 deg. Hydrides were most frequent at inclinations of about 20 deg and 90 deg. In Zircaloy-4, hydride plates were inclined to the basal plane at angles vanging from 5 to 25 deg with the predominant inclinatioiz equal to 12 deg; no platelets were found near the prism plane position. In both zircoinium and Zir-caloy-4, hydrides were principally, but not exclusively, parallel to (1011) type planes. When the Zircaloy-4 gmins were subjected to tension stresses of 12,100 psi and 19,400 psi during hydride precipitation, the hydride habit was unchanged except that precipitation favored those habit planes which were inore nearly perpendicular to the stress direction. The stress-orientatioiz effect increased with the magnitude of the stress. THE hydride habit plane in a zirconium has been determined by several investigators. Langeron and Lehr1 in 1956 found platelets parallel to (1010) slip planes. In 1962, Westlake and Fisher2 confirmed these findings and showed that hydride precipitation on twin planes, as reported by Kunz and Bibb,3 was probably due to incomplete removal of worked metal from specimen surfaces. Secondary habit planes, ( 1011) and (1015), were also found by Westlake and Fisher under particular charging conditions where a hydride layer may have existed at the hydrogenation temperature. Most recently, walters4 and westlake5 again observed the (1010) habit exclusively in zirconium. Louthan and hgermans have reported that hydrides precipitate on various ( 101l ) and (112l) planes positioned 31.5 to 90 deg to the basal plane in Zircaloy-2. The present investigation was concerned with the hydride habit in Zircaloy-4 in relation to that in zirconium and the possible change in habit when precipitation occurs under stress. The latter consideration was prompted by the stress-orientation phenomenon originally reported by Marshall and Louthan.7, 8 I) EXPERIMENTAL Materials and Specimens. Chemical analyses of all materials are given in Table I. The zirconium specimen was a 1 by 4 in. section cut from wrought crystal bar that was hot-rolled at 790°C to 0.300 in. and cold-rolled to a final thickness of 0.095 in. All surfaces were mechanically polished and then chemically polished with a solution of H2O, HNO3, and HF (10:10:l by volume) prior to annealing. Grains as long as 0.25 in. were grown by thermally cycling the specimen three times (in 10-5 mm Hg vacuum) between 825" and 1000°C at approximately 125°C per hr. The specimen was isothermally annealed at 825°C for 24, 40, and 120 hr after each cy-

Jan 1, 1968

By Charles W. Schwartz, Subash Kolluru

INTRODUCTION Creep of rock in situ, like most rock mass behavior, will be largely governed by the behavior of the natural discontinuities -- bedding planes, faults, and joints, in particular, Several past studies have investigated various aspects of the time-dependent deformation of rock discontinuities; examples include Amadei and Curran (1980), Engelder and Scholz (1976), Johnson (1975), Kaiser and Morgenstern (1979), Solberg et al. (1978), and Wawersik (1974). These studies have provided much insight into the general phenomenon, but they have also produced some inconsistent conclusions and left many unanswered questions. This paper will attempt to shed some light on one of these questions: What is the influence of stress level on the creep of unfilled rock joints? The discussion will follow a two-part approach to the problem: (1) laboratory creep experiments on small scale jointed specimens, (2) a simple theoretical mechanism to explain, at least in qualitative terms, some of the results from the experimental program. EXPERIMENTAL PROGRAM Uniaxial creep tests were conducted on intact and jointed samples of a specially formulated gypsum plaster "synthetic rock." Synthetic rock materials have several advantages over natural rock for long-term creep testing: (a) higher creep rates, (b) lower strength and therefore lower loading requirements, (c) simpler specimen preparation, and (d) more controlled and consistent properties. Gypsum based plasters have been used previously in studies of short-term strength and deformability of jointed samples (Patton, 1966; Einstein and Hirschfeld, 1973). Furthermore, Williams and Elizzi (1977) demonstrated that natural gypsum, at least, creeps in a manner similar to that of most other creep-susceptible natural rocks.

Jan 1, 1982

Jan 1, 1970

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By Spencer S. Shannon

This chapter is concerned with the uses, geology, exploration, evaluation, preparation for markets, and future of 90thorium and 39yttrium, along with 14 rare-earth elements. The rare-earth metals or lanthanides were divided into three categories by Berzelius. The cerium subgroup is comprised of 57lanthanum, 58cerium, 59praseodymium, 60neodymium, and 62samarium. 61Promethium does not occur naturally. The terbium subgroup includes 63europium, 64gadolinium, and 65terbium. The remaining lanthanides are placed in the yttrium subgroup. Strictly speaking, yttrium is not a rare earth. Because the properties of yttrium resemble those of heavy rare earths, its name has been used as a designating adjective. The yttrium subgroup includes 66dysprosium, 67holmium, 68erbium, 69thulium, 70ytterbium, and 67lutetium. Rare-earth elements, especially those of the same subgroup, tend to occur together rather than in discrete minerals.

Jan 1, 1975

By T. S. Lundy, J. I. Federer

Chemically purified Zr95and Cb95 have been used in determining self-diffusion coefficients in the bcc phase of iodide zirconium over the temperature range of 900o to 1750°C. The temperature dependence of the diffusion coefficients could not be described by the usual Arrhenius-type equation over the entire temperature range. Values of the apparent frequency factors (D0)a and activation energies (Q)A for ZR95 varied from 4.8 x 10-6 to 2.5 x 10-2 sq cm per sec and 20,700 to 46,900 cal per mole, respectively, between 900°and 1750°C. Similarly, for Cb95, values of (Do) a and (Q)A varied from about 2.4 x 10&apos;5 to 0.25 sq cm per sec and 26,500 to 56,800 cal per mole, respectively. The data may be described in terms of the a to ß transition temperature of 1136 °K and the absolute temperature of the diffusion anneals by the following eauations: SEVERAL studies on the diffusion of Zr95 in zirconium have been reported.1"5 The values of the constants contained in the usual Arrhenius-type equation for describing the temperature dependence of the diffusion coefficient, D = Do exp [- Q/(RT)], are summarized in Table I. The reported values of Do, the frequency factor, and Q, the activation energy, are seen to vary by factors of about 60 and 1.6, respectively. Examination of the data from any one study indicated reasonable consistency of measurements. The large discrepancies of over-all results, therefore, cannot be explained on the basis of experimental scatter. One possible explanation for the differences in results could be a varying impurity content of the zirconium. Another possibility is that the radioactive daughter, Cb95, influenced the values of some of the determined diffusion coefficients. Therefore, the first of the three purposes of this study was to reconcile the large differences in diffusion results that have been obtained. Several empirical relations have been proposed to relate the diffusion coefficients in solids with physical properties, such as the absolute melting point, the heat of fusion, and the heat of sublimation.

Jan 1, 1963

By Harold Margolin

The Ti-Al system certainly merits the investigative attention it has been receiving and this latest contribution by Blackburn is therefore to be welcomed. The titanium-rich end of the phase diagram shown here, as well as the diagram by crossley,17 Clark et a1.,18 and Tsujimoto and Adachi,29 reveal no other intermediate phase than Ti3A1, although a previous work by Ence and Margolin20 had reported an additional intermediate phase. Since then, Buerger Precession pictures of single crystals of 10.5, 11.5, and 12.5 wt pct A1 were made at New York university21 and the extinctions were found to be typical of a D6h a Ti structure. Some superlat-tice spots and/or streaks suggesting the presence of an Mg3Cd structure, i.e., Ti3Al, were also found. Since these specimens had been quenched from the y region20 and had revealed a Ti, it was concludedz1 that y does not exist and the structures interpreted as m + y could not be so considered. The absence of normal two-phase behavior in these structures had been indicated in the paper. Accordingly, the two-phase region y + 6 becomes a + Ti3Al and there is some agreement between the results of Blackburn and of Ence and Margolin20 as to both shape and existence above 900°C of an a + Ti3Al field. Crossley 17 proposed that Ti3Al is a line compound which decomposes congruently at 900°C. It is difficult to discount entirely the fact that clear two-phase structures, varying in amount with position in the two-phase field, could be detected above 900°C by Ence and Margolin.20 Precipitation during quenching could not have been so regular and the twin-phase syndrome17 does not apply. The heat treatment and quenching technique was essentially the same as was used by Crossley, whereas Blackburn, who used a rapid quenching procedure, also showed a two-phase a + Ti3A1 field above 900°C. If the two-phase field exists above 900° C, it is easy to picture a two-phase field which could account for the data of Crossley below 900°C without invoking a line compound existence of Ti3A1. All that would be necessary would be an 0 + Ti3Al/Ti3Al boundary which curved sharply to higher aluminum contents below 900° C. It is clear that the controversy must be solved by techniques which obtain data at elevated temperatures without quenching. It is conceivable that the difference in width of the a + Ti3N fields reported by Blackburn and by Ence and Margolin is due to the longer annealing times used by the latter investigators. The criterion for establishment of equilibrium in our work20 was the

Jan 1, 1969

By H. R. Stahl

FIVE mills are operated in Southeast Missouri by the St. Joseph Lead Co.; these have a total rated capacity of 24,300 tons per day divided as follows: Federal, 12,000 tons; Leadwood, 4800 tons; Desloge, 3600 tons; Bonne Terre, 2400 tons; and Mine La Motte, 1500 tons. These concentrators are similar in a general way, differing mainly in size and type of equipment and in minor variations in flow sheet. No attempt is made rigidly to standardize procedure in the various mills in spite of a general similarity in the ores. Each mill may be regarded as a separate laboratory in which new ideas and changes may be tried. A generalized description of the process is given, noting important differences in procedure at the various plants. The concentration process may be divided into five main stages: dry crushing, wet grinding, desliming and classification, tabling, and flotation.

Jan 1, 1947

By Carl Zapffe

THE object of the Bradley process is to free manganese oxide from its associated gangue and separate the contained iron oxide by dissolving the manganese and precipitating it from the solution. &apos;The fundamental features of the process are : making. both 1 a manganese ore and an iron ore; effecting a separation of manganese .and. iron by means of selective roasting; leaching- the manganese from the roasted ore by using &apos; ammonium sulfate; precipitating the manganese by using the ammonia gas generated during leaching; fixing the precipitate by oxidizing with air; breaking down and reforming the ammonium sulfate, so that daily very little additional ammonium sulfate beyond that originally charged into the system is required; washing the manganese precipitate and the iron-silica residue and evaporating the liquor to conserve the dissolved salts in the moistures of these two products and &apos;to reduce the sulfur content,; drying the precipitates; magnetic wet-concentration of the iron-silica residue; sinteriny the manganese-and .the&apos; iron-concentrates.

Jan 1, 1929