Search Documents

By Baker G

The detailed mineral composition of the lead-zinc ores at Captain's Flat was first studied in 1942 (Edwards, 1943).At that time the workings did not extend far below the 750ft. level. Since then development has been extended to the 1,390ft. level, and -at the request of the management of Lake George Mines Ltd., an examination of the ore from the deeper levels has been made as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.This account is. based on that examination (Mineragraphic Rept. No. ,537, C.S.I.R.O.)GENERAL GEOLOGYThe geology of the Lake George Mines has been described briefly in The Geology of Australian Ore Deposits (1953), and in much greater detail in an unpublished report by K. Glasson (1952). The area consists of fossiliferous Upper Ordovician sediments overlain by volcanics (Kohinoor VoJcanics), and by fossiliferous Silurian sediments. The volcanies comprise a series of· flows ranging in' composition from dacite to rhyolite, with interbedded tuft's and shale lenses.The region has been strongly folded. The regional strike is from 340° to 355°, and dips are from 75°W. to 75°E, A major syncline, pitching 200 N., occupies the centre of the area. The Kohinoor Volcanic'l outcrop as two bands which represent the east and west limbs of this syncline.The Volcanks in the western limb, with whIch the orebodies are associated, are more strongly sheared than those in the eastern limb.

Jan 1, 1953

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By Yago Rodrigues de Moraes, Carlos Bruno Eckstein, Gabriela Ribeiro Pereira, Clara Johanna Pacheco, Matheus Campolina Mendes, Laudemiro Nogueira Junior, Iane de Araújo Soares, Luiz Henrique de Almeida

Os aços austeníticos HP são empregados na fabricação dos tubos de fornos de reforma a vapor, sobretudo pela manutenção de sua elevada resistência mecânica e à corrosão, a temperaturas superiores à 700°C. Contudo, intercorrências durante a operação podem causar o bloqueio do fluxo interno de matéria-prima, gerando um aumento rápido de temperatura na parede do tubo, muito superiores àquelas de projeto. Este tipo de falha é conhecido como surto de temperatura, e pode levar à formação de grandes trincas longitudinais no equipamento. As caracterizações das transformações ocorridas no surto são importantes para determinar os parâmetros de detecção dessa condição através de ensaios não destrutivos. Por isso, com a finalidade de analisar a resposta magnética de amostras que sofreram surto, foram avaliados dois casos. O primeiro corresponde a análise de uma amostra proveniente de um tubo de reforma a vapor que sofreu surto de temperatura durante operação. O segundo caso, corresponde a amostras com estado V de evolução microestrutural, que foram submetidas a um ciclo térmico para simular o surto. A análise foi realizada via microscopia de força magnética. Os resultados obtidos mostraram resposta magnética no contorno dos carbetos da amostra surtada em serviço e na amostra com simulação a 1050°C.

Oct 23, 2019

By Chas. E. van Baraeveld

"The information presented in this report is a by-product of studies concerning zinc, and is published in response to various inquiries for information as to the suitability of zinc for roofing. It parallels a previous report of the Bureau of Mines on slate roofing.Available Forms of Zinc RoofingZinc is available for roofing in three forms: 1. As sheet zinc which may be used advantageously on roofs with as flat a pitch as 1 in 4; laid with standing seam construction for small roofs and with batten construction for large roofs. 2. As corrugate sheets, in widths up to 40 inches and in lengths up to 8 and feet, available for siding and roofing in industrial buildings (with certain re¬strict ions) and or farm buildings (without restrictions). 3. In the form of shingles.Advantages of Zinc Roofing1. Zinc is a permeant roofing material; that is, when suited to the conditions, and properly applied to a roof designed with the right purlin spacing it will outlast the building and still have a salvage value equal to a least half the original material cost. It is applicable to a wide range of conditions, from the most expensive to the cheapest type of construction, and is not greatly above the cheaper materials in first cost. A permanent roof of simple outline need not cost over $15 to $25 per square (100 square feet), depending upon the method of construction required a corrugated sheet roof for industrial purposes or for farm use need not cost over $15 per square for ordinary conditions. 3. Corrugated zinc sheets have the distinct advantage of being available for re-use and re-construction if handled with ordinary care. 4. Zinc oxidizes to a certain point, building up a strong protective coating which in time effectually checks further oxidation; thus it does not oxidize to the point of destruction as steel does, 5. It is light and easily handled."

Nov 1, 1924

By Joe Komadina

DOUG HALBE: Our next topic is one that I would think everyone might want to contribute to. I'm sure everyone here has had some experience in this area. If you haven't, I'd suspect you've never really run a mill. This is what we call "Horrible Spill Areas We Had When We Started Up the Plant and How We Fixed Them." Our next speaker has had a really great operating career. He had many years with Newmont in the Carlin area, and now he's executive vice president and chief operating officer of Independence Mining Company: Jim Komadina. I don't have to be nice to the speakers anymore, do I? [laughter] You may wonder why we picked Jim Komadina to give this talk. I was involved many years ago in the start-up of Newmont7s Gold Quarry plant. Jim held quite a responsible position there. I'm not going to say anymore, but I have in the back of my mind this picture of the pump floor and a rowboat and a guy rowing around on the pump floor. [laughter] Jim, was that you? [laughter] JIM KOMADINA: Probably. I wasn't responsible for the design. [laughter] Actually it's amazing. I've seen a lot of these plants and actually had the opportunity to walk around them, so when I say this, "Horrible spills I have seen and done," it's because I've been responsible for more than my fair share of them. But having seen a lot of spills, I will present a little bit of wisdom about how to prevent them.

Jan 1, 1998

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report The inherent suitability of coal for metallurgical purposes depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, Be well as the amount of available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Harlan County, Ky., for coking tests was based, in part, on recent studies of coal reserves by Wallace,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in tons, as follows:

Jan 1, 1956

By Wolfgang Pietsch

DR iron') is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949

By A. C. Johnson

The Bureau of Mines explored the Three Kids deposit in 1941 as part of a strategic minerals program. Earlier mining and exploration had established the presence of a substantial tonnage of medium-grade wad ore, and drilling and sampling by the Bureau of Mines, in collaboration with the Federal Geological Survey, indicated an additional tonnage such that development and exploitation became more clearly feasible. Private interests, with Government support, undertook to produce metallurgical-grade manganese. The present paper describes the Bureau of Mines exploration and subsequent development. Manganese in the Three Kids area is found in one of the lower members of the Muddy Creek formation in a bed of fine sandstone and silt, which outcrops around the north edge of the River Mountains and generally dips 20° to 40° away from the hills. There is considerable variation in the thickness and grade of the ore. The ore is light weight, having a density of 1.2 to 2.

Jan 1, 1956

By R. J. Hundhausen

This report describes the exploration and recent utilization studies the Bureau of Mines conducted on the Iron King, Chambers, and Dry Camp chromite deposits in the John Day district, Grant County, Oreg. The field investigations were undertaken during parts of 1939 and 1942 to determine the tonnage and grade of chromite in the district that could be utilized as a war reserve for the steel industry. As a result of the Bureau's field work, which included construction of 9 miles of access road, 6,204 feet of diamond drilling, 195 channel samples, and 1,020 linear feet of trenching, an ore reserve of 208,000 tons of 22-percent chromic oxide was indicated in the 3 deposits. Less than 1,000 tons of this ore has been mined since the field work was completed because the 2 largest deposits are submarginal in grade and there is as yet no incentive to develop and mine the ore. Since the war, however, the Bureau has been seeking means of utilizing the ore. Two methods of utilization that show promise are direct smelting of the ore in an electric furnace and use of the chromite for making refractory brick.

Jan 1, 1956

[IRVING, JOHN D. :-(Continued.) Some Features of Replacement Ore-Bodies, and the Criteria by Means of Which They May be Discovered, XLII, [xlvii]. Discussions: on A Concise Method of Showing Ore-Reserves, XLIII, 714; on The Iron Deposits of Daiquiri, Cuba, LIII, 65; I on Recrystallization of Limestone at Igneous Contacts, XLVIII, 214; I on To What Extent is Chalcocite a Primary, and to what Extent a Secondary, Mineral in Ore Deposits, XLVIII, 194. minerals of gold deposits, Homestake belt, Black Hills, S. D., XLII, 54.]

Jan 1, 1918

By Marcial Medina

El presente texto describe la reología de la Pulpa a nivel de química de superficie y así sugerir las alternativas a los problemas que impiden poder operar en forma continua y su capacidad de diseño la Planta de Flotación Diferencial de Cobre – Molibdeno. Asimismo, es necesario definir una solución a escala de laboratorio, la cual debe ser validada con pruebas industriales e implementarla en planta. La estrategia debe garantizar la continuidad de la operación de la Planta de flotación de Molibdeno con cualquier tipo de mineral y que no presente compactación la pulpa. Finalmente, se devbe agarantizar el procesamiento de toda la producción de la planta de cobre en la planta de flotación diferencial de cobre molibdeno.

Sep 12, 2011

By P. R. Jones

A computer program was written for the design of a shell and tube type heat exchanger on a price optimum basis. The program was designed to meet the following requirements: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; and (4) no change in phase. Price optimum design was obtained for four standard tube sizes and standard pitch. Pressure drop both inside and outside were computed and the nearest standard shells having at least the required area were listed. With this information, the estimator can select the heat exchanger best suited for the need. The program was made adaptable to various fluids and to various tube sizes and spacing by reading in much of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1967

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985