Search Documents

Papers presented at a U.S. Bureau of Mines (USBM) technology transfer seminar describe the causes of violent material failure in U.S. mines, measurement techniques for monitoring events that result in violent failure, and mitigation techniques for controlling failure. Specific factors contributing to violent failure are identified on the basis of geotechnical monitoring in 16 U.S. hard-rock and coal mines and on statistical analyses of 172 coal bump events. New monitoring and analysis techniques developed as tools for assessing violent failure; geotomographic methods that provide new capabilities for the study of material failure and stress changes over large areas; and seismic methods for determining source locations, calculating energy release, and determining source mechanisms are described. Fair correlations have been established among seismic parameters, elastic stresses, face support load, and violent events. USBM studies have identified the advantages using both yielding and stable pillars for coal bump control. A computer program has been developed as an aid for selecting room-and-pillar layouts. The practical aspects of implementing a destressing program is outlined for coal mines, while the importance of mine orientation and timely support installation in controlling buckling-type failure is identified for hard-rock mines.

Jan 1, 1995

By R. A. Busch, R. R. Backer, R. W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slur- ry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton sample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol- ids). The resultant friction-pressure gradients ranged from 0.06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposi- tion tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, ad- ditional water was released; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitabil- ity for use as backfill material in active mines.

Jan 1, 1965

By M. Rafie, M. Rinne, F. Samimi Namin

"SynopsisRock mass classification systems constitute an integral part of empirical underground excavation design. One system that is commonly used to classify rock mass is the Rock Mass Rating, or RMR, system. The RMR system has evolved over time to better reflect the perceived influence of various rock mass factors on excavation stability. While the introduced modifications have enhanced the applicability of this classification system, there are still areas that cause potential ambiguity. The RMR system cannot deal with input data ambiguities, uncertainties, and vagueness. To deal with the uncertainty, a Fuzzy Rock Mass Rating (FRMR) has been developed. This study aims to describe the main concept of the fuzzy approach, which is implemented in the FRMR to classify rock mass. The FRMR considers the uncertainty associated with the input data (uncertain variables) used in rock mass classification. The Gol-e-Gohar (GEG) area 3 iron ore deposits in the south of Iran were chosen as the case study for investigating the applicability of FRMR. The results of this study show that the FRMR software tool can easily be used for rock mass classification, even if uncertain input parameters have been used. FRMR consists of three parts, each of which is suitable for certain conditions.IntroductionNowadays, rock engineering classification systems, which constitute the backbone of the empirical design approach, are widely employed in both civil engineering and mining engineering. Rock mass classifications have recently been quite popular and are being used mostly for the preliminary design and planning purposes of projects. According to Bieniawski (1989), a rock mass classification scheme is intended to classify the rock masses, provide a basis for estimating deformation and strength properties, supply quantitative data for support estimation, and present a platform for communication between the exploration, design, and construction groups."

Jan 1, 2015

This publication is the fourth in a series of miners? circulars covering various phases of accident prevention in bituminous-coal mines; these circulars constitute a text hook for courses of instruction on accident prevention in bituminous-coal minim. To these may be added material of particular interest in the field where the course is presented. Other circulars in the series are: Accident Statistics as an Aid to Prevention of Accidents in Bituminous-Coal Mines (Miners? Circular 47). Accidents from Falls of Roof and Coal in Bituminous-Coal Mines (Miners' Circular 48). Accidents from Hoisting and Haulage in Bituminous-Coal Mines (Miners' Circular 49).

Jan 1, 1946

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By Felipe das Dôres Machado

No processo de fabricação de aço, o distribuidor possui grande importância na questão limpeza inclusionária, principalmente, quando se trata da produção de aços limpos (clean steel). As inclusões podem afetar negativamente as propriedades mecânicas e metalúrgicas do aço. Estudos realizados em modelos físicos e/ou matemáticos vêm sendo aplicados com intuito de propor medidas que melhorem a capacidade do distribuidor na remoção de inclusões presentes no aço. Este trabalho tem como objetivo principal qualificar o escoamento de um distribuidor e quantificar a remoção de inclusões do mesmo. Um modelo físico de um distribuidor de lingotamento contínuo de tarugos construído em acrílico e que respeita a similaridade de Froude e Reynolds é utilizado para os ensaios. A quantificação das inclusões é realizada por meio de um ensaio que envolve um sistema de injeção de partículas de polietileno na entrada no distribuidor e outro sistema de coleta dessas partículas na saída do distribuidor no qual as amostras coletadas, posteriormente, são secadas e pesadas. Com os resultados obtidos pretende-se compreender o efeito dos parâmetros propostos sobre a remoção de inclusões e permitir a utilização de uma ferramenta capaz de avaliar a qualidade de aços no que se refere à passagem de inclusões na saída do distribuidor.

Jul 30, 2018

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By Luís Carlos da Silva

Apresenta-se uma revisão das características e propriedades do nitreto cúbico de boro (cBN) bem como de diferentes tipos de processamento. A influência da adição de ligantes e a formação de compósitos com outras cerâmicas são também revistas. Finalmente, destaca-se a grande importância prática do cBN como cerâmica de elevada dureza na substituição do diamante em ferramentas de corte.

Oct 30, 2017

By T Davids, B J. J Botha

The presence of an extensive soft siltstone layer in the middle of the inter-burden sequence of rocks at Syferfontein Colliery in South Africa prompted tests to determine the effect of different mid-column decks of inert material in the siltstone layer. The objective was to achieve significant cost savings in explosives use whilst not degrading dragline productivity. An important factor that had to be considered was that the initiation systems available in South Africa are not accurate enough to ensure simultaneous initiation of explosives decks in a hole.

Jan 1, 1994

By W. H. Zieman

"THIS IS THE THIRD of the consecutive Annual Forums on Grinding that were instituted by Mr. L. E. Djingheuzian in 1957. The first was on the subject of Ball Milling (Transactions, Volume LX, 1957) and the second on The N on-Cataracting Ball Mill (Trans-actions, Volume LXI, 1958). From the discussions at these forums it was evident that one of the most important factors affecting the efficiency of grinding is the shape of the liners. In order to make a study of liners in use, it was •decided to seek the co-operation of operators across the country by sending out questionnaires requesting basic information. Additionally, these operators were urged to set down briefly any pertinent information on the subject acquired through experience and experiments at their own particular plants. A compilation and analysis of these data were to form a basis for discussion at the Forum on Liners at the Annual Meeting in Montreal, April, 1959. The response of the milling fraternity to this solicitation was most gratifying, and clearly indicated the importance attached by the operators to the effect of liner design upon overall grinding performance."

Jan 1, 1959

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush's work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By Noel N. Moebs

This report summarizes a U.S. Bureau of Mines study on the application of geotechnology to identify and minimize ground control hazards in talc mining operations in northwest Georgia. The major ground control hazard is pillar sloughing attributed to the steeply dipping orientation of a pronounced foliation in the talc ore body. The sloughing problem, which gradually reduces the effective support area of a pillar through attrition, can be minimized by appropriate artificial support, as determined by a rock classification system, and by a more uniform pillar design. A boundary element model confirmed the advantages of using a uniform pillar design to avoid excessive loads on portions of irregular pillars. Instrumentation to measure roof convergence and pillar loading was installed at selected locations in an active talc mine but failed to detect any significant changes, suggesting that the gneiss hanging wall constitutes a strong roof that probably can support large spans between pillars and permit high extraction ratios. This interpretation also is supported by a rock classification of the hanging wall gneiss.

Jan 1, 2010

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By Lars-Kristian Trellevik, Jan Arvid Ingulfsen

Swire Seabed is dedicated to being at the forefront of the Autonomous Subsea Revolution. The company is currently working along and developing operational, technical and market strategies where autonomous technology is the driving force. Swire Seabed’s vessel Seabed Constructor is currently mobilized and operating eight Hugin AUVs and 6 Surface going USVs. This significant and revolutionary spread is owned by Ocean Infinity. Ocean Infinity and Swire Seabed is currently involved in the search for the missing MH370 – in about 3 months the vessel and autonomous spread have fine combed an area of deep sea floor spanning over more the 100 000 km2 . With such a considerable spread with a depth rating of 6000 meter – Swire Seabed and Ocean Infinity is challenging long held paradigms in subsea mapping and resource surveys. Highly accurate and precise data can be acquired for large areas in record time, and at a comparatively much reduced cost. As one earlier required several vessels and associated crews and logistical support – Swire Seabed and Ocean infinity are now able to operate a large number of AUVs and USVs, through technological advances in automatic data-processing and interpretation, from a single offshore vessel. This opens up vast possibilities for emerging markets such as subsea-minerals. Swire Seabed is also developing strong collaborative relationships with academic institutions. Along with UIB Swire Seabed is developing methodology for deep sea geological and geophysical resource searches applying AUVs at an industrial scale – this work is based on UIBs groundbreaking work and significant experience in the same fields. In particular Swire Seabed and K.G Jebsen Centre for Deep Sea Research (UIB) have developed methodologies for conducting detailed Seep-Searches at a large geographical scale. UIB and Swire Seabed is further pursuing a formalized long term relationship for academic and industrial cooperation and exchange in AUV operation and methodology development. Whilst K.G Jebsen Centre for deep sea research have been involved in basig deep sea research for years, Swire Seabed have specialized in cost-effective heavy duty operations in water depths greater the 3500 meters. This collaboration affords the subsea mining community a unique pool of both insight and operational capacity.

Jan 1, 2018

By Hossein Aminian, Daniel Hodouin, Claude Bazin, Claude Jacob

"Solvent extraction followed by electrowinning (SXEW) is an economical option for the processing of low grade and oxidized copper ore. Phenomenological models were developed to simulate the copper solvent extraction and the electrowinning processes. The two models were linked together to make a SX/EW simulator. The simulator is used to predict the operation of the mines Gaspe pilot plant put in operation in 1996. Results confirm the potential of the simulation that would subsequently be used for student training, process optimization and to assess the performances of control strategies.INTRODUCTIONSolvent extraction followed by electrowinning (SXEW) has become in the last two decades a key process for the recovery of copper from solution obtained by leaching low grade copper ore. Several operations have been commissioned in North and South Americas in the last decade (Arbiter, 1994). In Canada, Gibraltar Mine (Scott, 1991) operates a SX plant followed by electrowinning (EW) to produce copper cathode from leached low-grade ore dumps. From 1996 to 1997 Mines Gaspe operated a pilot plant to test the economical feasibility of leaching an oxidized copper ore, followed by solvent extraction and electrowinning of copper. Despite copper SX/EW processes have the reputation of being low cost operations, plant engineers should always look at way to make the plant more efficient. Process models provide an economic platform to learn, control and ultimately optimize the operation of a plant.Several models have been independently proposed to simulate the SX process (Cadman and Hsu, 1970; Medina Gomez, 1980; Wilkinson and Ingham, 1983; Garcia et al., 1988; Aminian et al., 1997) and the EW process (Bryson, 1981; Barton and Scott, 1992; Barton and Scott, 1993). However few papers, if any, deal with the integration of the two process models into a single simulator of a SX-EW plant. This paper describes the development of an integrated simulator for the SX-EW process and shows some steady-state simulation runs of an actual SX-EW pilot plant. The paper consists of four sections. The first section shows the general layout and principles of operation of a SX-EW plant.The second section describes the SX model while the third section deals with the process model used for the copper electrowinning process. The last section shows how the two process models are linked to simulate the operation of the Gaspe pilot plant."

Jan 1, 1999

By G. E. Wittur

"The twenty-one members of the Organization for Economic Cooperation and Development, comprising eighteen western European nations plus Canada, the United States and Japan. account for two-thirds of world steel production. The Special Committee for Iron and Steel was formed by the OECD to study trends and problems in the steel industries of member countries. The paper begins with a summary on the Organization, including an historical sketch, its structure, member-ship and objectives. The steel industry of the entire OECD is briefly described before proceeding to a more detailed discussion of various aspects of the steel industries of European OECD members, emphasizing practices and conditions that differ from those in North America. Benefits to Canada of representation at meetings of the OECD Special Committee for Iron and Steel are described."

Jan 1, 1967

By L. A. Conley

This report, covering the period January through December 1976, contains abstracts of articles related to cost engineering and economics for chemical and petroleum plants, mining, and other mineral industries from the following periodicals: 1. Air Pollution Control Association Journal 2. Chemical Engineering 3. Chemical Engineering Journal 4. Chemtech 5. Coal Age 6. Coal Mining and Processing 7. Combustion 8. Drilling-DCW 9. Electrical World 10. Engineering and Mining Journal

Jan 1, 1977

By Rudá Grossi Coimbra Martins

A estruturação organizacional da gestão da informação em Central de Serviços já está consolidada no ambiente de Tecnologia da Informação. O ambiente de Tecnologia de Automação compartilha características semelhantes, já que também fornece serviços para seus clientes. Entretanto, serviços de automação possuem particularidades derivadas, em grande parte, do fato de que são mais críticos para a atividade fim da empresa, já que visam manter a operação. Implantar uma Central de Serviços em ambiente de Tecnologia de Automação de uma empresa já existente demanda uma série de modificações em termos de Tecnologias, Processos e Pessoas para trazer os retornos desejados em termos de gerenciamento, organização da rotina e disponibilidade dos ativos. Este trabalho apresenta alternativas para atuar sobre os três componentes supracitados durante a implantação de uma Central de Serviços, com foco em sua operação através de uma Gestão Compartilhada (Cosourcing). Experiências adquiridas em projetos de especificação e operação de Central de Serviços também são apresentadas para embasar a estruturação da gestão da informação em ambiente de Tecnologia da Automação de indústrias de Metais e Mineração.

Jul 30, 2018

Generation and Attachment of Submicron Size Bubbles to Colloidal Solids

Sep 13, 2010