Search Documents

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

By R. Strandahl

As one of the largest private utilities globally, E.ON currently operates hard coal fired power stations in with a total installed capacity of some 20.000 MW: These thermal power plants consume domestic coals but are increasingly dependent on imported seaborne traded coal (in 2009 approx. 17 million t). Knowing that the company’s reputation and credibility depends in part on how E.ON lives up to the responsibilities along the entire energy value chain, E.ON takes a collaborative approach with the various suppliers. Hence, E.ON’s responsible policy also applies to the procurement of coal; the utility launched in 2009 a comprehensive Corporate Responsibility program with special focus on supply-chain audits. One of the first coal audits focussed on the Cerrejón coal mine in North Eastern Colombia. The authors will share the key learning’s and experience from the Colombian audit jointly conducted with an independent auditor and E.ON experts from the Corporate CR and E.ON Energy Trading.

Jan 1, 2011

A Seismic Hazard Scale (SHS) has been developed to provide a practical seismic hazard assessment tool applicable to mine site personnel. It has been applied to seismic data sets from numerous Western Australian mines. The SHS is applicable when quantifying seismic hazard on a mine wide scale, on a mining block scale, and on a local cluster-by-cluster scale. Spatial mapping of variations in seismic hazard is a particularly powerful application of the scale. The SHS is sensitive to temporal increases in seismic hazard. It has also been shown that the SHS can be applied to estimate seismic hazard when seismic monitoring data are not available. The SHS is a simple derivation of the Gutenberg-Richter relation. There are assumptions and limitations to the SHS that need to be considered when applying it to mine seismicity data.

Jan 1, 2004

By S Dunbar, S Harrison, J Cilliers

‘Those who cannot remember the past are condemned to repeat it.’George Santayana (16 December 1863 in Madrid, Spain to 26 September 1952 in Rome, Italy). Philosopher, essayist, poet and novelist.The minerals industry requires specific technical expertise in mining and mineral process engineering, geoscience, environmental science and social sciences to maintain and operate its current business and to develop future projects. A steady supply of new graduates is essential to replace not only retirees, but also those who left the industry during the recent downturn. The supply of trained graduates is however not instantaneous, and there is a four-year lag from entry into university to graduation. It is essential that this lag in human resource supply and a likely shortage of knowledgeable, qualified talent is taken into account when considering risks to the business of mining. The shortage of skilled professionals has in the past resulted in unsustainable salary expectations and is likely to pose financial and execution risk to new projects. This paper will review some recent statistics of students in training from around the world and explore what action is required to not only sustain the training courses that provide future ready talent to the mining industry, but also ensure that graduates from these courses are equipped to create change and be leaders in the industry. The future prosperity of the industry is dependent on delivering sustainable stakeholder returns through the cycle. This will be achieved by developing capable individuals that can respond to the complex, adaptive challenges facing the industry.*This is an abstract only. No full paper was prepared for this abstract.*CITATION:Plint, N, Cilliers, J, Dunbar, S and Harrison, S, 2018. Back to basics: resourcing the mining industry, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 33–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"In this study pertaining to the electrochemistry of chalcopyrite, the active/passive behavior of a chalcopyrite electrode in 0.5M sulfuric acid solution was investigated. Potentiostatic and potentiodynamic polarization and multi-cyclic voltanunetry were conducted to analyze the electrodissolution parameters of the electrode.The potentiodynamic and potentiostatic polarizations of chalcopyrite revealed the formation of a passive film on the surface of chalcopyrite. From the potentiostatic study in the passive potential region, a decrease in the dissolution current density by increasing the potential was observed. From this, it was concluded that the passive film is an n-type semiconductor and cation interstitial defects or anion vacancies are the charge carriers. From multi-cyclic voltammetry studies, four cathodic peaks at - 0.37, 0.30, -0.10 and-0.20 YsHE were detected on the surface of a passivated chalcopyrite electrode. The cathodic peaks at 0.37 and 0.30 V were connected to ferric to ferrous reduction and copper sulfide formation, respectively. The peaks at -0.10 and - 0.20 were related to chalcopyrite reduction. The products of the chalcopyrite reduction reactions were suggested to be Cu2S, Cu9fesS16 and Cu5feS4 and evolution of hydrogen sulfide gas (H2S).IntroductionChalcopyrite is the most abundant copper bearing mineral in the world and its dissolution behavior represents the most important technological consideration in the hydrometallurgical extraction of copper [I]. Since the current pyrometallurgical methods for copper extraction from chalcopyrite have environmental issues, many studies have considered the leaching and dissolution of CuFeS2 in different aqueous media [2-5]. The main problem associated with leaching processes is the slow dissolution rate of the mineral [6]. During the dissolution process, increasing the potential of the chalcopyrite in the anodic direction will cause the formation of surface layers which hinder the dissolution rate of the mineral [7]. The precise composition of the layers is in dispute. Previous studies have concluded that these layers could be sulfur [8-9], precipitated iron compounds [8], a solid electrolyte interphase (SEI) - which slows the rate of electron transfer- [10], a metal deficient sulfide [ll], or polysulfidic in nature [12-13]. In order to increase the leaching kinetics of chalcopyrite, the characterization of the layers formed during dissolution is essential and electrochemical methods are important to this end. Studies by Biegler [14] show nucleation and growth of a thin two-dimensional sulfide phase on the surface of chalcopyrite during the exposure of a polished sample in HzS04 solution or air. More studies by Biegler and Swift [15] have shown evidence for nucleation and growth of a 3-dimensional phase at low anodic potentials (around 200 mV vs. OCP). The current-time behavior of the dissolution process in this potential area has the characteristics of expansion and overlap of localized dissolution centers."

Jan 1, 2012

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985

By Leroy O. Gieseke, John B. Begley

If the particles produced and transported in your plant are as chunky as rough crushed coal or as fine as cement, there are probably several conveying and elevating systems suitable for your operation. The problem is deciding which is most suitable in terms of space, energy cost, allowable product degradation, productivity, and angle of movement. Each conveying and elevating method should be fit to the products it can handle successfully, to desirable economics, and to suitability for the overall operating scheme. Matching along these lines will result in selection guides that should be useful for many years, although design evolution is expected for the materials handling equipment involved. There are several common bulk material handling devices for moving solids: belt conveyors, screw conveyors, bucket elevators, chain conveyors, and en-masse conveyors/ elevators. En-masse conveyor/elevator equipment is commonly compared and contrasted with the other devices. These comparisons often involve en-masse versus all others. En-masse has developed into a versatile technique because the machines can move materials horizontally, vertically, or in closed circuit. Such machines unload, elevate, store, reclaim, and distribute materials-all without ancillary equipment except for chutes and gates. Bulk material can be carried, as with a belt conveyor or bucket elevator; pushed, as with a flight or screw conveyor; bumped, as with a vibrating conveyor; blown, as with a pneumatic conveyor; fluidized, as with a dense phase pneumatic conveyor; or by applying internal forces to it to induce "en-masse" flow. Conveying en-masse is analogous to the flow of a fluid in an open channel, and elevating en-masse is analogous to the flow of fluid in a pipe. In the case of a fluid, flow is caused by a differential in pressure. With en-masse movement, flow results from resistance to shear induced by the movement of chain and flights.

Jan 12, 1980

By Fábio de Oliveira Braga

A descoberta de óleo e gás no Pré-Sal transformou o Brasil em um dos grandes possuidores de reservas de petróleo no mundo e aumentou as expectativas de produção em águas profundas. Apesar da euforia, alguns desafios têm o potencial de inviabilizar a exploração do Pré-Sal: a complexa logística offshore, as dificuldades de acesso ao reservatório, as condições físico-químicas do poço e de subsuperfície. As condições impostas pelo ambiente são relevantes, devido aos altos teores de contaminantes, alta temperatura e pressão, que exigem materiais de alto desempenho. O objetivo deste trabalho é revisar os avanços que podem contribuir para superar as condições físico-químicas do Pré-Sal. Verificou-se que a solução deste problema pode envolver três tipos de abordagem: O desenvolvimento de ligas resistentes à corrosão (LRC), a adição de agentes modificadores do meio corrosivo (inibidores) e modificações no projeto dos equipamentos. Espera-se, portanto, que a utilização conjunta das diferentes abordagens proporcione a viabilidade de longo prazo da produção no Pré-Sal.

Aug 17, 2017

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

GENERALTHE coal deposit, where it is being worked, consists of a bed of brown coal varying in thickness from 120 ft. to 200 ft., covered by an overburden of clay, drift, loam, etc., of a thickness of 22 ft. to 40 ft., and averaging 28 ft.The overburden is first entirely removed from the coal, and then the coal is excavated by. large revolving shovels which work at the bottom of the hole or open cut in the coal and deliver it in shovel bucketfuls to the transport system. The shovels owned by the Commission and available for this coal excavation are two Bucyrus steam revolving shovels, one being type 150B, weighing 150 tons, having a 21-cub. yd. bucket, and capable of digging a 47-ft. face; and the other being type 175B, weighing200 tons, having a 31-cub. yd. bucket, and capable of digging a 61-ft. face.In addition to these two steam shovels, the Commission has recently obtained a No. 250 Ruston electric revolving shovel weighing 340 tons, and having a bucket of 10 cub. yd. capacity, and capable of digging a 75-ft. face. When this electric shovel has been erected it will replace the steam shovels on the coal excavation, and the permanent transport system has been designed to take delivery of the coal from its bucket.The duty to be performed by the transport system is to take the coal from the shovels, elevate it out of the open cut, transport it to the screening house, deliver it iuto the hoppers at the top of this building, then to take the coal after it has passed over the screens and distribute the required grades to the power house and to the briquetting plant.

Jan 1, 1924

By Carolina Machado de Castro Amaral

A necessidade de treinamento é uma realidade nas indústrias. A qualificação de operadores é importante para garantir segurança e prevenir perdas econômicas. Nesse contexto, o objetivo desse trabalho é desenvolver e avaliar um simulador de treinamento de operador. O estudo de caso é um moinho vertical, comumente utilizado na indústria de cimento. Nessa direção, passou-se pela construção de um supervisório, pela modelagem e simulação dinâmica de um moinho vertical e, por fim, pela elaboração e execução de um treinamento. Para tal, foram construídos três cenários de situações anormais, além da consideração da operação normal. Ainda em relação à metodologia, treinaram-se dois grupos de alunos com métodos distintos de ensino: o primeiro recebeu apenas um treinamento teórico, através de uma apresentação multimídia; e o segundo, após esse treinamento teórico, recebeu um treinamento prático, ou seja, do tipo aprender fazendo, a partir do contato direto com o simulador de processos. De modo geral, percebeu-se que o contato com a prática possibilitou um maior entendimento da operação do moinho vertical, do grau de dependência entre as variáveis de entrada e de saída, e das variáveis utilizadas para a recuperação do processo à operação normal, contribuindo ainda para uma maior fixação do conhecimento teórico. Esse trabalho é resultado de uma parceria UniversidadeEmpresa, cujas atividades foram desenvolvidas por um grupo de alunos de graduação em Engenharia Química.

Aug 17, 2017

IN 1949 the Government Printing Office issued Bureau of Mines Bulletin 468 3 and previously (in 1948) Bulletin 467 4 as part of the program under the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C., 321-325, and amendments). The two bulletins, relating to oil shale and its products, were published to present abstracts of all patents in this field from 1845 to 1945 5 or before the Synthetic Liquid Fuels Act was passed. Also, as part of this program, bulletins were published on patents relating to the pressure hydrogenation of coal e and the Fischer-Tropsch synthesis.7 The Synthetic Liquid Fuels Act was not extended beyond April 1955, but it inspired much increased activity in the field of oil-shale research, and many patent applications were filed. It is the purpose of this bulletin to abstract the patents issued in the United States, the United Kingdom, and Europe from 1946 to 1956, inclusive. A few older patents omitted in the previous bulletins have been included.

Jan 1, 1959

By Walter W. Kaufman

The braking performance of underground, rubber-tired, non-coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are included as well as related aspects of roadway construction and runaway vehicle protective devices.

Jan 1, 1977

By Lon Santis, Dale Ramsey

The use of aircraft to support blasting operations in mines, quarries and construction sites goes back to the early days of aviation. Invaluable at times, aircraft use has been limited by cost, the unpredictability of weather impacts and other factors. Recently several technologies have matured to open up a new way to acquire aerial data with unmanned aircraft systems (UAS), commonly called drones. Equally important, the U.S. Federal Aviation Administration has recently implemented an exemption process and rulemaking to implement the commercial use of UAS into the United States’ National Airspace. The skies are opening for many applications of UAS. The most notable may be photogrammetry, which is the science of making measurements from photographs, especially for determining the exact positions of surface points.

Jan 1, 2016

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

By James Wm. White

Calculation of consistent steady-state mass balances in operating metallurgical plants and pilot plants is of interest for many reasons. In general, enough data can - and should - be collected to overdefine the system, i.e., permit calculation of nonmeasured quantities via more than one path. In such cases, resulting steady-state metallurgical mass balances rarely close due to sampling, analysis and/ or instrument error. Indeed, determination of a valid calculational sequence for complicated process flowsheets with multiple recycle streams can prove quite difficult. Here we present and discuss a method that has proven useful in analysis of numerous grinding circuit flowsheets of varying-degrees of complexity our technique requires only a consistent process flowsheet with appropriate associated data and arbitrary numbering of streams and equipments. Process topology and user data are decoded to yield a set of "search" or base variables and a set of "calculated" variables in solids, water, particle size and splitter parameter space. This procedure greatly speeds subsequent actual mass balance adjustment calculations since perturing certain variables (e.g., a solids value) does not require recalculation of other variables (e.g., the water balance). Finally, internal search and calculated variables are back converted to User units and used in a Sum-of-Squares criterion. Global minimization of this performance functional then yields a consistent mass balance in a least, squares sense. Weighting factors of choice can be used. Examples illustrate application of these methods.

Jan 1, 1979

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003