Search Documents

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By J. E. Quinn, S. Wolstencrof, K. H. Soldenhoff

Ion Exchange (IX) using Strong Base Anion Exchange (SBA) resins is conventionally used to purify uranium from sulfuric acid pregnant leach solutions (PLS), particularly when uranium grades are relatively low. However, the presence of chloride in the PLS interferes negatively with conventional SBA based IX processes, by reducing the uranium loading on the resin. Chloride can be present in the PLS due to the use of saline bore or seawater in leaching, or chloride containing leach/IX reagents. ANSTO has been examining strategies to combat this problem for several years. ANSTO previously reported that a recently developed high-capacity SBA resin was capable of extracting uranium efficiently from saline leach liquors produced at Boss Resources’ Honeymoon in-situ recovery mine in South Australia. The resin was tested successfully in a 2017 Field Leach Trial carried out onsite in the existing wellfield area. While the piloting was extremely promising, the elution was more challenging, with eluate tenors limited to 2 g/L U3O8 using NaCl. This is due to the resin’s strong affinity for the uranium complex, which makes it difficult to elute efficiently by standard methods. In this paper, we describe a novel elution process developed for strong base resins that significantly improves upon conventional methods. The process, developed by ANSTO, is based upon conversion of the extracted uranyl sulfate species to uranyl carbonate, followed by elution with sodium chloride. The loading and elution process was demonstrated in continuous locked-cycle piloting conducted at ANSTO in 2019. The results were excellent, with eluate tenors of 8–9 g/L U3O8 achieved from Honeymoon PLS containing 50 mg/L U3O8, with very little transfer of impurities. In subsequent test work, the eluate was shown to be amenable to uranium peroxide precipitation. The results represent a huge step forward for the purification of uranium from saline leach liquors.

Jan 1, 2020

By Larry A. Shiprnan

DEMANDS upon power plants by the war program in 1941 intensified problems of coal utilization. It was an outstanding year in that field. The domestic heating stove witnessed outstanding development; the research folks progressing so rapidly that the design of the "perfect" stove is just around the corner. Use of colored motion pictures in analyzing fuel-bed performances has reached a new high with the colored pictures taken at minute intervals and projected at sixteen frames a second as shown by the Koppers Coal Co. and the Anthracite Institute (on domestic stokers) and the Consolidated Edison Co. (industrial stokers). Continued efforts of this kind will be beneficial in analyzing further some of the "Code for Testing Coal" problems confronting Subcommittee No. 2 of the Joint A. I. M. E. - A. S. M. E. Committees.

Jan 1, 1942

The Clyde Power Project, and its Clutha Valley Development forerunner, has taken widespread investigations for various hydroelectric purposes both along the valley floors upstream from Alexandra and on the higher schist terrain. As part of this work the nature and extent of many of the alluvial deposits have been resolved and the ages established with varying precision. Gold values have been approximately appraised in some areas as an element of environmental assessment.

Jan 1, 1992

By H. Huang, R. N. Gow

"The reactivity of an enargite mineral electrode was investigated spectroelectrochemically under conditions typically found in alkaline sulfide leach solutions, with pH 11-13 and Na2S additions of 50 and 250 gL-1. A bulk enargite electrode was cycled between 0 and -1,000 mV for each set of solution conditions. Raman spectroscopy was used to determine and compare surface formations against species in mass-balanced EH-pH diagrams generated using STABCAL. Previously, it was determined that arsenic could be selectively leached under alkaline conditions at an average solution potential of -300mV, across the pH range 11-13. Operating under such conditions allowed for the selective leaching of arsenic with elemental sulfur formation. From several of the voltammograms obtained during this current testing, the formation of elemental sulfur appeared at increasingly reducing conditions with increasing sulfide concentration. At high concentrations, copper started to dissolve, possibly as a bisulfide complex, reducing the selectivity of the leach, unlike previous studies. However, the presence of the higher sulfide concentration is also anticipated to prevent passivation by consuming any surface formation of elemental sulfur. This study provides insight into the operating parameters of alkaline sulfide leaching in regards to the selectivity of arsenic leaching, as well as guidance for control of reagents and solution potential and, of course, the need for water treatment afterwards.IntroductionEnvironmental limitations on the pyrometallurgical processing of arsenic-bearing concentrates have forced operations to consider other solutions. Attempts to hydrometallurgically process enargite (Cu3AsS4) fall into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under basic conditions. The authors believe that the selective leaching of arsenic is more amenable because it produces a solid copper phase, preferably chalcocite (Cu2S) or covellite (CuS) that could then be processed using conventional methods already in place in the copper and gold industries. Potential leaching methods include alkaline sulfide leaching (Achimovicovica et al., 1999; Anderson and Twidwell, 2008a,b; Tongamp et al., 2009 and 2010), hypochlorite leaching (Vinals et al., 2003; Curreli et al., 2005; Mihaljovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and acid leaching (Gow et al., 2014b) with or without fine grinding to mechanically activate the enargite surface and increase normally slow leach reaction kinetics (Achimovicova et al., 1999; Balaz et al., 2000; Balaz and Achimovicova, 2006). In this study, the reactivity of enargite under alkaline sulfide leach conditions was examined."

Jan 1, 2015

By M. Feely, W. G. O'Keefe, C. O'Reilly, M. P. Holdstock

A petrographic and microthermometric study of fluid inclusions in the Kentstown Granite, crosscutting quartz (VI) and calcite+quartz (V 2) veins in the granite and calcite+quartz (V 2) veins in the overlying sediments was performed on samples taken from the borehole. Comparisons of the type 1, type 2 and type 3 fluid inclusion populations recorded in the present study with those from other Irish Caledonian granites strongly suggest a similar fluid evolutionary history. Furthermore, the low-temperature CaC12-rich brines (type 5) of this study, which must be syn- to post-Lower Carboniferous in age, have correlatives both in Irish Caledonian granites and in the Lower Carboniferous base-metal deposits of the Irish midlands

Jun 19, 1905

In attempting to vegetate pnob!em sites some basic pn.i,ne%ptes, namely the phys.ica.e and chemi.ca2 pnope/ti;es og the problem mateni.al and the selection oU hu.itab.2e p!antts {cor pnopagati.on, have to be considered. Pnobtem sites such as tai ing dams, mined-out atteas, and areas which have been genehaUy advehse2y a46eeted by mining activities, are not only o~ten located in a divehs.ity o4 climatic regions, but they also usuaUy dL64en substantially in theAjt .int' Lns c phys.ica2 and chem.i cat pnopen t i.es . To estabP.ish vegetation on such sites 6requent2y requites: .%) The ame Lonaton oU adverse {yaetors in onde t to exeate a hoot env.utonment suitable Uon "satis1actony" plant growth. .%i) These.2eationo4 plant species suited to the improved Hoot env.utonment, and eompat%b&e with the e2imate o{y the site, and the ultimate Land use o4 the site. iii) The estabL shment o{y a Laboratory and p-LLot scale testing programme to aeeomptizh the above.

Jan 1, 1976

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

Preparation of MgO Nano-Particles with Magnesite

Sep 13, 2010

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By Joseph J. Feiler

Historical mining operations in Colorado and other western states have resulted in thousands of remnant mine openings. Many are sources of metals loading and acid water generation in surface and ground waters. It is estimated that more than 965 km (600 miles) of streams in Colorado have been impacted by past mining activities. The Animas River watershed in southwestern Colorado is one of the most heavily affected areas in the state. Abandoned mine features pose significant safety hazards to those who enter them. These hazards can include bad air, unstable rock or falls into open shafts, stopes and winzes. Backcountry skiers and snowmobile enthusiasts are particularly vulnerable to falls into snow covered mine openings.

Jan 1, 2006

By Robert Rautenberg, Paul McDermott

This paper will discuss the construction of 15.9 km (9.88 mi) of tunnels on a project in Chicago, Illinois. The tunnels were driven utilizing two rock and four soft ground TBMs ranging in sizes from 7.39 m (24.25 ft) in rock down to 1.95 m (77 in) in soft ground. In addition to the mining, there are 63 upper level structures and 16 dropshafts averaging 61.5 m (202 ft) deep included on this project. Many diverse mining, excavation, support and lining techniques were employed on this project.

Jan 1, 1997

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By Mônica Aline Magalhães Gurgel

O presente trabalho estudou a evolução microestrutural durante o recozimento no campo intercrítico de um aço baixo carbono com micro-adição de nióbio e molibdênio, laminado a frio, destinado a indústria automobilística, sendo este material da classe dos aços bifásicos. Com o intuito de verificar se os parâmetros utilizados no processo de fabricação (laminação a quente e a frio em função de uma determinada composição química) foram definidos de forma eficaz para obtenção da microestrutura esperada para um material “Dual Phase”. Os estudos foram suportados pelas análises da evolução microestrutural durante o processo de recozimento em escala laboratorial e análise dilatométrica, com o objetivo de determinar a faixa de temperatura no tratamento de recozimento em que as melhores propriedades foram atingidas. As caracterizações microestruturais e mecânicas foram avaliadas por Microscopia Óptica, Microscopia Eletrônica de Varredura (MEV) e ensaios de dureza Vickers.

Jul 30, 2018

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

By W. Bryszewski

As a result of strategic analysis in respect of the needs for air quality management a new advanced and holistic approach to air quality management process was introduced in the North West Province (NWP) of South Africa. The process is based on the principle of co-operative management. It involves both active participation of all Interested and Affected Parties (I&AP) and the holistic approach to solving problems with the underlying principles of shared ownership and sustainable development. The process consists of the followings phases: ? Industrial process quantification ? Quantification of impacts ? Formulation of the required control measures ? Definitions of certificate conditions ? Implementation of an adequate compliance management system at company level ? Ongoing co-operative air quality and system management with the strategic objective of continuous improvements The system has been successfully introduced in the North Province and proved to be an effective management tool and aids assurance of sustained environmental ability to cope with the pressure of industrial developments. The benefits and effectiveness are discussed using Hernic Ferrochrome as an example. Hernic Ferrochrome is one of the first companies, which successfully implemented this system.

Jan 1, 2004

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

Esso-BHP have installed a production supervisory control system that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control.The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexibility to handle future variations in operating conditions.The system will be extended to the Halibut platform late in 1970 and to the Kirlgfish platforms during 1971.

Jan 1, 1971