Search Documents

By Richard T. Newcomb

This paper considers the many problems involved in estimating rates of technical change via productivity indexes. In mining, declining ore grades complicate the measurement of progress considerably. The estimates discussed in this article were made for the United States iron mining industry by means of two techniques: a simple model of production with two inputs, and multiple regression. The results can be used to explain the relation existing on U.S. iron ranges between rates of exhaustion, technical change, output per man and the increase in capital proportions observed since World War I. Similar ob-servations can be made on the mining sector trends in the United States, Canada, and Japan. Formidable problems confront the economist attempting to estimate the influence of technological changes on the progress of mineral industries. Peculiar to these industries is the problem of how to adjust any measure of technological progress for the offsetting influence of exhaustion. Exhaustion has long been recognized in the mining industry as a critical dimension. Empirically, it is usually treated as a problem of declining grades of ore either in production or in reserves. There are studies of the trends in mining industries attempting to relate changes in input requirements to changes in grade and technology over time. Most frequently, the measure used to indicate technological progress is average labor productivity, e.g., output per man-hour. However, although such an approach has the merit of being simple and direct, it ignores the influence of other important factors of production such as capital. Without defining both the nature of technological change and of production, it can be very misleading to identify increases in labor productivity with tech-

Jan 1, 1969

By Forrest T. Moyer

Injury experience in the coal-mining industry was worse in 1965 as both the frequency and severity rates of injuries increased 2 and 6 percent, respectively, over comparable data for 1966 (tables 1-8). The retrogression in the safety record during; 1965 resulted frog the less favorable record at bituminous-coal mines, which more than offset the improved injury experience at anthracite mines. The 259 fatal and 11,138 nonfatal injuries occurred at a rate of 45.77 per million man-hours of exposure and resulted in a severity rate of 8,960 days lost per million man-hours. Although the number of fatalities was the second lowest annual total in the recorded history, it was 17 higher than in 1964. At anthracite operations the total of 6 fatalities in 1965 was the lowest annual figure in statistical history. The annual numbers of nonfatal injuries at ill coal mines and the resulting rates of occurrence have varied little in the past 5 years (table 1). The total days lost from all injuries rose from 2.1.3 million in 19b4 to 2.23 million in 1965 (table 5). Fatal and permanent total injuries, with a standard time charge of 6,000 days each, accounted for 1,650,000 days; Permanent partial injuries, 191,932 clays; and temporary total disabilities, 383,911 days. The severity rate for fatal injuries was 6,241, 8 percent higher than in 1964, and the nonfatal severity rate of 2,718 days lost per million man-hours was 2 percent higher than in the preceding year. The average severity of permanent partial injuries ire; 730, or 48 days fewer per injury than in 1964. The average days lost for each temporary total injury was 36 days in each year.

Jan 1, 1968

By Budiselic C, Hefter G

The uptake of gold by activated carbon from acid chloride solutions involves the reduction of gold(IIl) to metallic gold. Deposition occurs only on the surface of the carbon at localized active sites at first, and subsequently at less active areas. The rate of uptake depends on the surface area of activated carbon, which confirms results from a recently published study (de Siegel and Soto, 1984). Increased rates of uptake were observed at higher temperatures and lower chloride concentrations due to the decreased stability of AuCI4-, the major gold(IIl) species present. Recoveries of gold approached 100 per cent for a contact time of 60 minutes at 20°C in a well stirred solution initially 5 ppm in gold(III) and containing 0.5 per cent w/v coconut-shell carbon. The presence of 0.25 Mnitric acid or 100 ppm iron(IIl) had no detectable effect on either rate or efficiency of gold uptake.

Jan 1, 1985

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0·5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

By A. Basçetin

Equipment selection in mining engineering is one of the most important decisions that affects the mine design, production planning and economic parameters in open pit and underground mining. Mine planning engineers generally use their intuition and experiences in decision making. Mostly, linguistic variables (the weather is raining, soil is wet, etc.) come into question and decision-makers may not know how these variables are computed. Since the advent of the fuzzy set theory, these uncertainties are easily interpreted in the decision-making process. The development of computer technology and programming of colloquial language with expert systems have considerably reduced decision-makers? burden. This paper reviews the development of a computer programme software called EQS (EQuipment Selection) that automates equipment selection in mining engineering using fuzzy set theory. The EQS with an introduction of the concepts and theories of multiple attribute decision-making, the fuzzy set theory, and EQS applications to mining industry problems with case studies are presented

Jan 1, 2006

By Joan T. May

Federal Bureau of Mines studies showed that some organic amine hydrochlorides can be used as dehydrating agents for producing anhydrous magnesium chloride from hydrates and brines. Laboratory-scale tests showed that double salts are formed by reacting 35 percent magnesium chloride brine or spray-dried magnesium chloride with pyridine hydrochloride. Heating decomposed these double salts to anhydrous magnesium chloride and recycle pyridine hydrochloride. Pyridine hydrochloride also chlorinated any magnesium oxide in the spray-dried magnesium chloride. The anhydrous magnesium chloride obtained by the method described contained less than 0.8 percent oxygen. More than 98 percent of the organic amine hydrochloride was recovered.

Jan 1, 1978

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By S A. Steyn, P Terrett

Air decking has become a widely practised method internationally for modifying fragmentation results and providing cost savings from reduced explosive consumption. Duvha has been applying air deck technology to overburden and midburden blasting for a few years. A thorough evaluation of air decking at Duvha has been made by instrumenting a number of blasts and analysing costs from direct savings in reduced explosives costs to savings in improved dragline productivity.

Jan 1, 1995

By Tracy Brettmann

In recent years the Augered Cast-In-Place (ACIP) Pile industry has seen a substantial increase in the quality control options available to Contractors, Engineers, and Owners. Quality control methods range from the simple, manual techniques that have been used for years to new computerized installation monitoring equipment and nondestructive testing methods. Our ability to monitor and test ACIP piles has grown to such a degree that the industry is struggling to determine how much quality control is enough. This paper reviews the many options available and describes the pros and cons of each. The various nondestructive testing methods, in particular, have been difficult to apply reliably due to misapplications of methods and misinterpretation of the results. ACIP piles have unique properties that require the various nondestructive testing methods available be considered very carefully in determining the method most appropriate for a particular use. Some nondestructive testing methods, as well as automated monitoring equipment, potentially can be applied effectively to increase the level of quality control for ACIP piles. The experience gained on real projects using these new methods, in conjunction with the old procedures, provides valuable information for future applications.

Jan 1, 2000

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By Samuel A. Goldberg

The Federal Coal Mine Health and Safety Act of 1969 delegated to the Bureau of Mines a yearly program of health inspections. Respirable coal mine dust concentrations are measured by Bureau inspectors. Samples of respirable coal mine dust are weighed to determine dust concentration and then analyzed for ash and quartz content. This paper describes the laboratory procedure for determining the percent quartz in the respirable coal mine dust samples.

Jan 1, 1972

In preparation for the 118th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS, Chairman. W. S. DICKSON, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. H. C. PARMELEE. FOREST RUTHERFORD., P. G. SPILSBURY. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP. Committee on Patriotic Meeting H. C. PARMELEE, Chairman

Jan 9, 1918

By S. Heusermann, S. Fahland, J. Behlau, A. Schäfers, J. Hammer

In the course of the deep subsurface use, the Federal Institute for Geosciences and Natural Resources has been carrying out extensive geological and geomechanical research and practical project work on domal salt structures, to prove their suitability e.g. for the disposal of radioactive wastes. Recent work on disposal sites has been taking into account the 3-D geological and geomechanical modelling of the underground structures. The geological models are generated using the special-construction openGEOTM code to improve the visualisation and interpretation of the geological data basis, e.g. borehole, mine, and geophysical data. For the geomechanical analysis of underground structures the JIFE finite-element tool has being developed to analyze large 3-D structures and to consider coupled THMC processes. The results of finite-element calculations, i.e. stresses, strains, displacements, and dilatant zones, are basic values for the evaluation of the stability of the structures and the long-term integrity of the geological barrier. As an example, the results of geological and geomechanical investigations of the Morsleben repository are presented including three-dimensional modelling of the entire geological structure of the central part of the mine as well as three-dimensional geomechanical model calculations to provide the necessary results for a long-term safety prediction.

Jan 1, 2015

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

Jan 1, 1962

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr2O3. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 16 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, stope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider stopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

In preparation for the 118th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS, Chairman. W. S. Dickson, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. P. G. SPILSBURY. H. C. PARMELEE. FOREST RUTHERFORD. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE. FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP. Committee on Patriotic Meeting H. C. PARMELEE, Chairman

Jan 10, 1918

By Bern Klein, Malcolm Scoble, Justin Widdifield, Andrew Bamber

"It has been suggested that the pre-concentration of ore underground can bring positive economic and environmental benefits to underground mining, particularly at extreme depth. The integration of mineral processing systems for coarse waste rejection and disposal into the underground mining environment has a substantial impact on the economics and operation of the mine. A case study for the integration of underground pre-concentration at Falconbridge’s Thayer Lindsley and Fraser Copper operations in Sudbury, Ontario is discussed, with particular focus on ore evaluation, system design, integration, and impacts on the operation. Conclusions as to the overall feasibility and potential impacts of underground pre-concentration are presented.INTRODUCTIONObjectivesA scoping investigation has been conducted for Falconbridge Ltd on the Fraser Copper Zone and Thayer Lindsley mines in order to develop a better understanding of the operations, and to do a preliminary evaluation of the potential for pre-concentration of the ore underground. The objective was to develop a conceptual design and evaluation of a pre-concentration system for each site. The results are to be used as the basis for a more detailed future study.Underground Pre-ConcentrationThe pre-concentration of ore to reduce the quantity and improve the quality of material transported to the processing plant is not a new concept and has been in practise at several mines including the American Zinc Company in Mascot Tennessee (Munro et al, 1982), the Sullivan Mine in British Columbia and presently at Xstrata’s Mt Isa lead-zinc mine in Australia, as well as at several PGM mines operating in the South African Bushveld. For each of these mines, a high degree of waste rejection was achieved at a coarse particle size with good metallurgical recoveries. The benefits arising from the surface pre-concentration of ore are well documented in the literature (McCullough et al, 1999; Miller et al, 1978; Munro et al, 1982; Schena et al, 1990; Sivamohan & Forssberg, 1991)."

Jan 1, 2006