Search Documents

By Jeff Whyatt

Deformation of underground salt, trona and potash mines is generally time dependent, providing for gradual adjustment of strata to mining induced stresses. Time dependence can allow for higher extraction ratios provided eventual failure can be tolerated. However, this eventual failure can be violent if creep deformation can shift stress and potential energy to strong, brittle geologic units. The mine failure case studies reviewed here illustrate this process. Yield pillars and defects in bridging strata figure prominently in these cases. Yield pillars provide local and temporary support to the roof, temporarily delaying the cave; and allowing extraction ratios and overburden spans to increase beyond the long term capacity of overlying strata. Defects (faults, voids, thinning) of strong overburden strata reduce the critical span, sometimes to less than panel width. Analyses of many of these cases have focused on a cascading pillar failure mechanism, but recent work and this review point to failure of strong overburden strata as the essential element. The suddenness of failure and attendant seismic events pose hazards to miners and, in some cases, to those on the surface. Characterizing these failures is a first step towards recognizing and managing the risk of catastrophic collapse in underground mines.

Jan 1, 2008

By L. S. Darken

IN the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be repre-sented satisfactorily by the simple equilibrium expression K - (p1)p1 (p2)p2 . (R1)r1(R2)r2 . where (P) denotes the concentration of a product and (R) the concentra-tion of a reactant in the reaction r1R1 + r2R2 + . . . Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a com-ponent is not proportional to its true mol fraction, But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple com-ponents and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satis-factorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature as ionization or the occurrence of polar and nonpolar molecules-are presumably less effective in metal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

By T. P. Dolley

Domestic production of industrial sand and gravel in 2004 was about 29 Mt (32 million st), a 6-percent increase from 2003. This increase was buoyed by a robust construction sector of the U.S. economy. U.S. apparent consumption was 30.3 Mt (33.3 million st) in 2004, an in-crease from 2003. Imports were about 490 kt (540,000 st) in 2004, an 11-percent increase from 2003. Imports of silica are generally of two types. They include small-quantity shipments of very-high-purity silica or a few large shipments of lower grade silica that were shipped only under special circumstances (such as very low freight rates).

Jan 1, 2005

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999

By Keith S. McIntosh

The fire assay process for the quantitative recovery of platinum group elements (PGE?s) prior to subsequent analysis traditionally is a time-consuming process. Samples derive from various ore types and contain PGE?s at the ppm or ppb levels, making concentration of the elements mandatory before assaying. Traditionally sample turn-around times are of the order of 24 hours. The whole sequence of sample preparation, fire assay and subsequent analysis of PGE?s have been automated by Anglo Platinum. Some of the major challenges on the road to automation will be discussed and the novel solutions that were implemented. The engineered solution included robotic automation of the whole sequence, from sample preparation, up to the final element by element assay. The final system allowed for rapid (less than one hour) and accurate analysis of PGE?s even in streams containing very low levels, such as flotation tailing streams and drill core samples.

Jan 1, 2006

Application of Natural Zeolite for the Removal of Diethylenetriamine (DETA) and DETA-Metal Complexes from Flotation Process Water

Sep 13, 2010

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,' by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By H. Matsuoka, M. Kawata, K. Mitsuhashi, C. Tokoro, T. Kato

Copper sulfide minerals such as chalcocite, bornite, and chalcopyrite exhibit high floatability, thus they can be recovered as a froth product by adding only a collector in flotation process. However, when their surface is oxidized, the floatability decreases and the simple addition of collectors is no longer effective. In this case, flotation activators are required to improve the floatability. Sodium hydrosulfide (NaHS) acts as an activator for chalcocite and bornite by re-sulfurizing their oxidized surface portions. Nevertheless, the flotation conditions still require optimization in order to achieve a satisfactory recovery of copper minerals. This work addresses the study of the effect of pH and NaHS dosage on the flotation of a complex Chilean copper ore containing chalcocite, bornite, and chalcopyrite. Flotation experiments were conducted using a Denver-type flotation cell and by investigating the effect of two NaHS dosages (50, 100 g/t) and three pH values (8, 9, 10). Following this process, the surface interaction between the minerals and NaHS were analyzed using zeta potential measurements. INTRODUCTION In recent years in the mining area of metal resources, the complexity of ores and the fineness of grind required to liberate minerals have become serious problems. When ores are complex, several valuable minerals may interact with each other and reactions may become more complicated compared with an ore containing only one valuable mineral. Therefore, more processing steps may be required than for a simple ore. When the valuable minerals exist as fine grains, it is difficult to liberate them and more grinding time is required. Furthermore, the probability of collision of fine particles with bubbles in the flotation process declines and it takes much time to recover them. Flotation is one of the most applied methods to separate valuable minerals from unwanted ones using the difference of hydrophobicity (or hydrophilicity). In the flotation method, the air is fed to a cell filled with the pulp of the mineral of interest and agitation is implemented to introduce air and generate bubbles. The hydrophobic particles attach themselves to the bubbles and float along with the bubbles while the hydrophilic particles remain in the pulp. Copper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are widely known abundant copper resources. Generally, flotation is used to recover and concentrate these minerals. Copper sulfide minerals usually have high floatability. However when their surfaces are oxidized, their floatability becomes lower. When the sulfide surfaces are oxidized, activators are added before flotation to modify the surface property of the Copper sulfide minerals so that they can be floated. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao (2018) reported that NaHS is often used as a sulfurizer for oxidized sulfide minerals (Becker (2014), Clark (2000), Newell (2006), and Newell (2007)). In earlier work, the authors performed flotation tests on a sample of Chilean copper ore which contained chalcocite, bornite, and chalcopyrite using a Denver-type flotation apparatus. The sample was ground to P80 70 µm with a rod mill and ball mill. In these tests, the following conditions were used: natural pH (about pH 8.5), flotation time of 45 min, 60 g/t AP3477 (sodium diisobutyl dithiophosphate) as collector, and MIBC (methyl isobutyl carbinol) at appropriate dosage as frother. NaHS was applied at the dosage of 0, 67, and 120 g/t, respectively at the conditioning. The concentrates were collected at 6, 18, 30, and 45 min. The weights of the concentrates and tailing were measured and they were assayed for copper by ICP-AES (Optima 5300 DV, PerkinElmer Inc.). The flotation recoveries of the copper minerals were calculated from the results of MLA (mineral liberation analyser) (MLA 650, FEI) measurements.

Jan 1, 2019

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By Breno Totti Maia

Metalurgistas e pesquisadores de aciarias a oxigênio buscam dia após dia o desenvolvimento de parâmetros operacionais com reflexos diretos em ganhos metalúrgicos e no desempenho dos equipamentos, visando aumentar a produtividade e evitando interrupções para manutenção. O principal requerimento para um converterdor a oxigênio é o conjunto de lança com bico de cobre. Recentemente a Lumar Metals apresentou cartuchos com a tecnologia Slagless que podem ser usados para substituir os bicos convencionais de cobre com expressivos resultados de processo. Alguns pontos são fundamentais para se obter um projeto de bico que tenha satisfatória vida útil, como por exemplo, a estrutura do material utilizado, o correto dimensionamento do circuito de refrigeração e o correto dimensionamento dos lavais de saída do oxigênio. O objetivo do presente trabalho é avaliar os efeitos dos parâmetros de processo: pressão e vazão e suas influências no desgaste do bico de lança devido ao mau dimensionamento dos lavais ou quando operando em condições abaixo da especificada. Os resultados mostram que para cada conversor com um perfil operacional único, o projeto do bocal específico é o que garante os melhores ganhos metalúrgicos e aumento da vida útil do bico.

Aug 16, 2017

[W. R. Abbott, 11o8 First National Bank Bldg., Denver, Colo. L. E. Adams, 817 Newhouse Bldg., Salt Lake City, Utah. Herbert Addison, Big Horn Colliers Co., Denver, Colo. Richard V. Ageton, Brighton Mich. John Alexander, Dacona, Colo. C. A. Allen, 448 Capitol Bldg., Salt Lake City, Utah. David Allen, Lafayette, Colo. John Allen, Ludlow, Colo. Thomas Allen, Mt. Harris, Colo. Gerald Alley, C. F. & I. Co., Pueblo, Colo. Archie Allison, Box 562, Walsenburg, Colo. D. S. Allison, 56 W. 6th South Street, Salt Lake City, Utah. Park Allison, Box 94.0, Rock Springs, Wyo. Howard R. Allonier, care Lunkenheimer Co., Cincinnatti, Ohio. J. B. Ambler, care Ambler & Riter, Engineers, Salt Lake City, Utah. A. F. Anderson, 403 Ideal Bldg., Denver, Colo. W. K. Anderson, 4.23 East Yampa Street, Colorado Springs, Colo. Sam Andrews, 503 Pike Avenue, Canon City, Colo. Jos. Angster, Farr, Colo. William Angus, Somerset, Colo. Joseph Appleton, Ironton Engine Co., Ironton, Ohio. Victor Arnoldi, Ideal, Colo. John Arnott, Crested Butte, Colo. R. M. Atmore, Swastika, N. M. W. H. Backman, 1601 Alcott Street, Denver, Colo. Edward E. Barrett, Roberts & Schaefer Co., Chicago, Ill. G. F. Bartlett, 311 Ernest & Cranmer Bldg., Denver,, Colo. C. S. Beach, Kemmerer, Wyo. Thos. Bertram, Box 134?, Oak Creek, Colo. Charles Beuchat, Pryor, Colo. John Bevan, 1625 North Corona Street, Colorado Springs, Colo. James L. Bisch, Van Houton, N. M. Jos. Bodner, Oak Creek, Colo. A. H. C. Boissier, 302 E. & C. Bldg., Denver, Colo. John M. Bopp, 1615 Walker Bank Bldg., Salt Lake City, Utah. Edward Bottomley, Carneyville, Wyo. James V. Bowen, Union Coal and Coke Co., Denver, Colo. Alex R. Bowie, Bowie, Colo. John S. Bowie, Bowie, Colo. Wallace D. Bowie, Bowie, Colo. W. J. Bowns, Castle Gate, Utah. L. Brandenburger, 59 West Broadway, Salt Lake City, Utah. James Brennan, Primero, Colo. W. D. Brennan, Dawson, N. M. Burt B. Brewster, 704 Kearns Bldg., Salt Lake City, Utah. A. L. Brockman, Sugarite, N. M. Alex. J. Brooks, Supt. Hastings No. 5 Mine, Hastings, Colo. Edward Brooks, Sweetwater, Wyo. E. S. Brooks, Rock Springs, Wyo. D. W. Brown, Rocky Mountain Fuel Co., Denver, Colo. L. E. Brown, 1212 Walker Bldg., Salt Lake City, Utah. Mark Y. Brown, 629 East Main Street, Trinidad, Colo. H. H. Bubb, Carbon Coal and Coke Co., Cokedale, Colo. W. H. Bullock, 1052 Gas and Electric Bldg., Denver, Colo. Thomas B. Burnite, 523 Boston bldg., Denver, Colo.]

Jan 1, 1921

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008