Search Documents

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described. The methodology has been used to measure strain resulting from blasting, and establish appropriate blast vibration limits on a brick sewer tunnel, an underground mine heading, brick veneer houses, a water pipeline, and transmission tower foundations. An outline is given of the use of the methodology to establish limits for the main entry heading of an underground coal mine, and transmission tower footings. The methodology that is described has reduced uncertainty factors, and permitted the specification of higher blast vibration limits than had been previously used.

By M. S. Miller

With prevailing assumptions that plentiful domestic coal reserves will be available for meeting our Nation’s expectations for on future low emission, coal-fired power plants, major government funding in Clean Coal Technology, and Carbon Sequestration Programs continues to be aggressive. However, after more than a decade of cutbacks in funding for domestic coal-related programs and personnel, there is a growing concern that adequate quantification and qualification of our Nation’s coal reserves is increasingly being compromised. This paper will define the growing concerns and dichotomies that continue to increase, and address the decreasing number of fossil fuel mapping and assessment programs by Federal and State programs.

Jan 1, 2004

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By T. C. Holmes

Introduction The Dome mine, in the Porcupine mining camp of northern Ontario, is one of the important gold mines of the country, having produced over 139 million dollars worth of gold from the commencement of production in '1910 to the end of 1944. The geology of the mine is complex and a number of types of ore are known, each occurring under particular conditions. The mine workings are very extensive and by far the greater part of them have been geologically mapped only in reconnaissance fashion. By 1940, when the writer joined the mine staff, the orebodies in the sedimentary trough and the 'nose' orebodies, the first types to be developed, were almost worked out and many workings were inaccessible, so the descriptions of these types are based largely on study of the plans and records. The same applies to a lesser extent to some other types. At various places in this paper, statements are made as to the mineralogical or chemical composition of the rocks. Most of these determinations are based on examinations made with a hand lens and cannot, therefore, be regarded as very reliable. General Geology As there are several types of ore in the mine, occurring under quite diverse conditions, a brief outline of the geology is given here, sufficient to provide a general picture into which the fuller descriptions given with each type of ore can be fitted.

Jan 1, 1947

The speed and internal accuracy of today's electronic calculators can be utilized to write an efficient slurry calculation program. The calculator's input/output printing feature offers additional benefits for data organizing and record keeping. This program allows slurry calculations to be performed without the urgency of immediately transferring a calculated result onto a process flowsheet or specification sheet. The number of flowsheets required for some hvdrometallurgical processes means the number of process stream blocks or ladder diagram entries can become substantial. Slurry calculations for such projects tend to become repetitious and tedious, and the chances for errors increase both in calculation and data entry onto process documents. Using this program has minimized both types of errors. Checking process flowsheets is particularly expedient with the program because you may "walk" through the flowsheet on a weight basis, i.e., solids rate and solids density, and have the program verify and/or correct the volume entries, gallons, and specific gravities. The program was initially used on a beneficiation project to check some 500 data entry values on ladder diagrams covering seven process flowsheets. Numerous hand calculation errors were determined and corrected, and the time for completely checking and correcting the flowsheet ladder diagrams was substantially reduced.

Jan 4, 1981

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982

Visit to the Modderfontein factory of A. E. & C. I. Ltd 23rd November, 1972 A full programme was arranged to suit both the mining and metallurgical sections of the Institute. After refreshments were taken and visitors welcomed by the factory management we were split into two groups, viz metallurgical and mining. Book review Stress-relief Heat Treatment of Vanadium Steels by Or G. O. Joy and Or A. M. Sage (21 pp, 77 references).

By H. L. Hartman

The past 15 years have seen rapid advances in the metallurgy of materials for drill machinery and bits, but rock drilling itself continues to be largely an art. Jet piercing, roller bit rotary drilling, and rotary percussion are all promising new techniques, but the percussion rock drill, still used for 90 pct of the blastholes in U. S. hard-rock mining, has undergone no major modification since pneumatic machines were first used successfully in the 1860's. This singular lack of progress stems directly from ignorance of the nature of impact failure of rock and the fundamentals of rock penetration in general. For nearly three-quarters of a century, mining engineers did not know what went on at the bottom of a drillhole. More and more, in recent years, investigators in the field have come to realize that to understand percussion drilling they must study the basic action of percussion bits penetrating rock—not the per- formances of commercial rock drills, with their many attendant variables that cannot be isolated or controlled. Using a vertical drop tester, the writer investigated the sequence of rock failure under the impact. of a simple, chisel-shaped bit when changes were made, singly, in significant variables. Results of this and other research are reported here. BASIC CONCEPTS The formation of a crater in rock under the impact blow of a bit can be observed experimentally. Directly beneath the edge of the bit the rock is crushed into fine powder; toward the sides of the crater it chips out into relatively large fragments. An explanation of these phenomena has been offered by Drilling Research Inc. on the basis of work sponsored by this organization at Battelle Memorial Institute (Ref. 1,1954, Summary, pp. 9-18). High-speed photography and force waveforms obtained from strain gages mounted on the bit near the cutting edges recorded the sequence of events in crater formation with a die-shaped or blunt, wedgc-

Jan 1, 1960

By R. L. Virta

Six companies mined fire clay in Missouri and Ohio during 2004. Production, based on a preliminary survey of the fire clay industry, was estimated to be 398 kt(438,700 st), valued at $9.81 million. This was slightly less than the production and value figures from 2003. Missouri was the leading producer state. It accounted for more than 70 percent of the U.S. production. Consumption Domestic producers sold or used fire clay primarily for refractory applications. This application accounted for 79 percent of the market. Refractory products made using fire clay include firebrick and block, grogs, high-alumina brick and specialties, refractory mortars and mixes, and saggers.

Jan 1, 2005

By Richard Rice

TURBO blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting. FIG. 1.-STEAM TURBINE DIRECT CONNECTED TO AIR COMPRESSOR. The first blast-furnace blowing engine of this type to be installed in America was built by the General Electric Co. and is installed at the oxford Furnace of the Empire Iron & Steel Co. This machine was put into operation March 8, 191.0. A duplicate unit is situated at the furnace of the Northern Iron Co. at Port Henry, N. Y., which unit was put into opera ion June 30, 1910 (Fig. 1).

Jan 5, 1914

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999

By W. E. C. A. B. Eustis

(Read at the Philadelphia Meeting, February, 1878.) IN September last I had my attention called by Mr. R. G. Leckie to a deposit of nickel in the township of Orford, province of Quebec. In many ways it has proved to be a subject of great interest. As this ore is, as far as I can learn, entirely new in mineralogy and metallurgy, it has seemed to me that it would be a matter of interest to the Institute to have laid before it, in a short paper, the peculiarities I have met with in studying it. This deposit of nickel was first described by Dr. T. Sterry Hunt, our President, in the Geology of Canada, 1863, p. 738, in the following terms : "The general diffusion of nickel throughout the magnesian rocks of the Quebec group has been already noticed. It has, however, never been met with in any considerable quantities in these rocks, although workable deposits of its ores may reasonably be looked for

Jan 1, 1878

By W. E. C. Eustis

In September last I had my attention called by Mr. R. G. Leckie to a deposit of nickel in the township of Orford, province of Quebec. In many ways it has proved to be a subject of great interest. As this ore is, as far as I can learn, entirely new in mineralogy and metallurgy, it has seemed to me that it would be a matter of interest to the Institute to have laid before it, in a short paper, the peculiarities I have met with in studying it. This deposit of nickel was first described by Dr. T. Sterry Hunt, our President, in the Geology of Canada, 1863, p. 738, in the follow ing terms: " The general diffusion of nickel throughout the magnesian rocks of the Quebec group has been already noticed. It has, however, never been met with in any considerable quantities in these rocks, although workable deposits of its ores may reasonably be looked for

Jan 1, 1879

When defining a ?megaproject,? one need only to look at Seattle, WA?s State Route 99 Alaskan Way Viaduct replacement project. This $3.1-billion project is one of the largest of its kind in the world, and includes the use of the world?s largest tunnel boring machine (TBM). However, for as large as the Alaskan Way project is ? especially given the size of the TBM being used ? there are several other megaprojects underway around the world. Each has its own challenges that require innovative design techniques and financing arrangements, as well as variations on established tunneling technologies. So it was that 266 tunneling and underground construction professionals ? owners, contractors and engineers ? convened in Seattle in November for the Cutting Edge Conference on Megaprojects. This was the second joint meeting between the Underground Construction Association of SME and the North American Tunneling Journal. The first joint conference took place in April 2012 in Miami, FL and attracted 238 attendees. A third joint conference, to be held in 2014, is in the planning stage. The key reason Seattle was chosen as the site of the megaprojects conference is the Alaskan Way Viaduct project. Before the conference began, many of the attendees were able to visit the project and get a close look at Bertha, the Hitachi Zosen earth pressure balance TBM that is boring the tunnel. In addition, the conference included an exhibit that attracted 20 industry suppliers, up from 10 the previous year in Miami. The 25 presentations during the two-day conference covered all aspects of the tunneling and underground construction of megaprojects. Topics included the Alaskan Way Viaduct project; considerations for procurement and contracting; political risk, financing and insurance; international megaprojects; risk and risk sharing and project delivery. Each session concluded with panel discussions.

Dec 1, 2013

John Langton, New York, N. Y. (communication to the Secretary*):—In Mr. Firmstone's discussion (Trans., xli., 912) the formula he gives for the periodical payment—his equation (2)—may be simplified in form. The expression given by Mr. Firmstone is : q=S(l+ r) 1-(1+r)-(1+r) r which is a simpler form to use in calculations. Where S= principal to bc extinguished. Q = periodical payment or charge for sinking-fund, r = rate of interest per period (i. e., interest on $1 per period). n = number of payments or periods. Kent's Mechanical Enyineer's Pocket Book, under the heading Annuities, equation No. 5, gives : " The annuity which $1 will purchase for any number of ytlars n is * Received Jiily 16, 1911.

Jan 1, 1912

One Hundred Sixteenth Meeting of the Institute, Monday, Feb. 18, to Thursday, Feb. 21, inclusive, 1918. Committee on Arrangements J. E. JOHNSON, JR., Chairman BRADLEY STOUGHTON, Vice-Chairman A. R. LEDOUX J. V. N. DORR L. W. FRANCIS F. T. RUBIDGE G. D. VAN ARSDALE MRS. S. J. JENNINGS E. M. SHIPP RALPH W. DEACON ARTHUR L. WALKER The program for the New York Meeting, in February, 1918, as planned by the Committee on Arrangements at meetings in the middle of December, and therefore subject to slight alteration in detail, is as follows: MONDAY, FEBRUARY 18 9 a. m. to 5 p. m. Registration at Institute Headquarters. 10 a. In. Technical Sessions. 12.30 p. in. Luncheon at Engineering Societies' Building. 2 p. m. : Technical Sessions. 8.30 p. m. War Smoker or Patriotic Meeting. TUESDAY, FEBRUARY 19 10 a.m. Annual Business Meeting, followed by Technical Sessions.

Jan 1, 1918