Search Documents

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By V. Canby

Introduction Located in Russia’s Chukotka Autonomous Region near the Arctic circle and 425km from the seasonal port of Pevek (population approximately 4600), Peschanka (or ‘Anyui’) is perhaps the world’s most isolated CuMoAu porphyry deposit of significant grade and tonnage. In addition to its extreme remoteness (66°36'N/164°30'E) and lack of developed infrastructure, Peschanka is located in one of the world’s coldest regions, with annual average temperatures well below freezing. Soviet exploration up to 1985 defined four zones with inferred resources of roughly 940Mt @ 0.51% Cu, 0.42 g/t Au, 1.4 g/t Ag and 0.019% Mo (1).

Jan 1, 2007

E. A. Peretti (University of Notre Dame, Notre Dame, Ind.)—Mr. Deitz and Professor Halpern are to be congratulated on a fine piece of work which adds to our knowledge of precious metal—cyanide-solution reactions. I should like to offer the following comments: The authors state, "the rate plots were always linear, indicating a zero order reaction rate." This appears to conflict with the data of Fig. 6 which clearly show the rate to vary with the NaCN concentration. It seems to me that the rate curves are linear because of the experimental setup. The volume of solution is so large that over a three-hour period the change in NaCN concentration is very small. A rough calculation for the experiments of Table I where the initial NaCN strength was 0.0096 mol per liter show a change of NaCN concentration of about 0.0009 mol per liter at the end of three hours. In short, over the period of time that the experiment was in progress, the NaCN strength was practically constant; hence the rate of dissolution remained practically constant. Eq. 10, as written, specifies that 1 mol of H202 and 2 mol of hydroxyl ion are formed when 2 mol of silver react. Is this true? The effect of H,O2 on the rate was made in solutions having an oxygen pressure of 4.8 atm. Were any tests made in solutions containing hydrogen peroxide, but no oxygen? G. M. Willis (University of Melbourne, Melbourne, Australia)—The authors have shown that, under their experimental conditions of high O2 concentrations, the rate of solution of silver in aqueous cyanide solutions is controlled by diffusion of O2 or CN- to the metal surface. With diffusion control, it is generally not possible to obtain further information about the mechanism of a process.

Jan 1, 1955

By H. Kasaini

Batch wise adsorption tests for platinum (Pt) on the surface of activated carbon pellets (Norit RO 0.8 BET surface area 1100 mg/g) were carried out in mixed chloride solution. The purpose of this study was to assess and compare the adsorption performance of amine-treated activated carbons (AACs) and native activated carbons (NACs) in terms of adsorption capacity and selectivity. The effect of pH and temperature on adsorption capacity and selectivity was established. The amine- treated ACs were prepared by anchoring the amino groups (butyl amines) on the surface of AC pellets in aqueous media and the UV-Vis was used to determine the amount of amine sequestered from solution by ACs. The dosage of butyl amine on the surface of ACs averaged 0.15 g/g, carbon. The adsorption mechanism was described by the ionization and complexation model whereby interaction between the protonated AAC surface and the anionic chlorocomplex ions (PtCl5 [H2O]-, PtCl62-) proceeded by either electrostatic attraction or/and by covalent bonding [(NH3)2PtCl6 or (CH2COO)2PtCl6]. By comparison, the adsorption capacities of Pt on amine-treated ACs and native ACs were 53.8 mg/g and 33.03 mg/g, respectively which highlight the benefits of anchoring functional molecules on ACs. The selectivity of AACs was influenced by solution pH. Pt adsorbed selectively on the surface of amine-treated ACs at pH<1.5. The highest separation factor that was recoded pertained to Pt and Fe species (ßPt/Fe = 90) then followed by Pt and Ni species (ßPt/Ni = 30) or Pt and Cu species (ßPt/Cu = 15). The lowest separation factor was recorded for Pt and Cr ions (ßPt/N= 5). Adsorption kinetics of Pt on amine-treated AC surfaces, according to the first and second order reactions, were investigated and results showed that rates were in the order 10= 5). -4 min-1 and 102 g?min/mg, respectively. The pseudo 1st order kinetics predicted the adsorption capacity of 51.81 mg/g which was almost similar to the experimental value (53.8 mg/g) while the second order rate equation predicted Pt adsorption capacity of 40.1 mg/g. Both The Langmuir and Toth isotherm fitted the Pt adsorption at pH < 1.0. The Freundlich isotherm tended to underestimate the adsorption capacity of AACs.

Jan 1, 2014

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By Vinícius Cardoso da Rocha

Frente ao cenário industrial competitivo, o emprego de fluxantes em lingotamento contínuo de aços permitiu o aumento da produtividade e a redução das perdas metálicas por defeitos superficiais. Neste estudo, avaliou-se a aplicabilidade de dois tipos de fluxantes para produção do aço SAE 1046 Mod. Os fluxantes foram testados quanto ao desgaste da válvula submersa, frenagem (atrito) na interface metal/molde e rejeição dos produtos de lingotamento devido à presença de defeitos superficiais. O fluxante teste apresentou taxa de desgaste de válvula submersa de 2,2 mm/corrida, frente ao fluxante padrão com 0,8 mm/corrida. Entretanto, o fluxante teste demonstrou bons resultados quanto à lubrificação do molde, reduzindo a frenagem (atrito) entre o metal e molde e, consequentemente, melhorando a qualidade superficial do produto de lingotamento. A rejeição dos produtos por defeitos superficiais reduziu 47% com o fluxante teste.

Aug 16, 2017

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999

JAMES DOUGLAS Dr. James Douglas, twice President of the American Institute of Mining Engineers, and one of its principal benefactors, died in New York on June 25, 1918, at the age of 81 years. After a life of extraordinary activity, failure of his health compelled him to retire about 2 or 3 years ago, and in view of his advanced years his death was not unexpected. His funeral was held at the Church of the Mediator, on June 26, and was attended by representatives of the American Institute of Mining Engineers and of the Canadian Mining Institute. His body was then taken to Quebec for burial in the family plot. An extended notice of Dr. Douglas, prepared by Dr. R. W. Raymond, will be presented in the September issue of the Bulletin. LEWIS NEWTON BAILEY Lewis Newton Bailey died of pneumonia at Camp Merritt, N. J., April 30, 1918, at. the age of 34 years. He was Master Engineer, .Senior Grade, in the Fourth Regiment, U. S. Engineers; and although he was offered a commission as First Lieutenant shortly after enlisting, he preferred not to accept it until he had reached France. By those who knew him well, this lack of eagerness for promotion will be recognized as consistent with his whole character.

Jan 8, 1918

By Edgardo Fogli, Mario Lampiano, Antonio Nicola

The project is located in the northern region of the People’s Republic of China and was awarded to Impregilo, as sponsor of the Wan Long Joint Venture, in September1997. The project consists of four tunnels for a total length of 88,700 m, with an excavation diameter of about 4.9 m. The lining is made of honeycomb pre-cast segments, connected by PVC dowels and the joints are sealed with elastomeric gaskets. The geology is mainly Limestone, Dolomite and Sandstone. Karst cavities are abundant and are often in-filled with plastic red clay. This has adversely affected the TBM’s progress. Four double shield telescopic TBMs were mobilized to cope with the very tight construction schedule and, at the end of November 2000, more than 80% of the tunnel has been bored. The article analyses the TBMs’ productions in the various geological conditions and the results of different technical solutions adopted at the project.

Jan 1, 2001

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

By C. H. Vivian

En el arte de las voladuras, la pólvora negra o de fúsil era el explosivo más usado. Posteriormente, las voladuras industriales experimentaron un cambio radical, forjado no por un nuevo material, sino por uno ya conocido. Se trata del nitrato de amonio, constituyente de la dinamita, que sólo puede hacerse explotar después de gran dificultad como uno de los principales fertilizantes. Por ello, a este componente se le añadió petróleo combustible, denominada comúnmente AN-FO. Dicha composición permite vender a razón de 5 a 6 centavos de dólar por libra en E. U. A y realiza la labor de dinamitas de 20 centavos de dólar por libra en muchas aplicaciones. En ese sentido, el presente texto señala la revolución, elaboración, historia, teoría, detonación, agujeros pequeños y los trabajos en túneles de las voladuras.

May 1, 1964

By C. S. Smith

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Dr. Gerhard Derge; Editorial Assistant, M. A. Redmyrski; Staff Coordinator, James J. Burke. THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Post-President; John Chipman, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretory. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman- Dennis Carney John Chipman J. C. Fulton J. H. Hollomon H. H. Kellogg, A. E. Lee, R. Moddin, J. D. sullivan, and D.&apos; Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. lnstitute of Metals DM lion: Robert Maddin, Chairman. F. Lincoln Vogel, Jr.. Vice chairman. W. A. Backofen R. W. Boliuffi J. H. Bechtold&apos; M. B. Bever R: S. Busk C 6. Goetzel poul Gordon C. D. Grobom, Jr., Robert F. Hehe-mann R. I. Joffee F. i. Joumot Jr. lrvin R. Kromer, A. J. Leno. Horold Morgolfn, C. J. McHargue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alon U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman. T. B. King, F. C. Laogenberg, W. O. Philbrook, and T. 0. Winkler. Publishod bimonthl by the American Institute of Mining Metollurgicol and Petroleum Engineers Inc., 29 West 39th Street, New York 16, N. Y. Telephone: PEonylvanie 6-9220. Subscription $20 par yew for non-AIME members in United States and North, South and Control Americo $25 foreign; $5 for AIME members. Single copies, $4.00, single copios foreign $5,00. The AIME is 1958 by the Amarican mode or opinion axpressed in it* publications ... Copyright by the Amarican lnstitute of Mining, MataIlurgicol, and Petrolum Engineers, Inc,. . . Reg. istered cable address AIME New Yark ... Indexed in Engineering Inderx, Industrial Arts ...Index and Chemicol Number5. Absrtracis . . . Second class postage paid at New York,Indor. N. Y., Industrialond Ann Arbor, Mich.

Jan 1, 1959

By Paramguru R. K, Jena P. K

Increasing demand for copper, lead and zinc with continuous depletion of good grade ore reserves, warrants the need for utilization of lean and complex ores of these metals. There is worldwide effort to develop suitable processes for these purposes. The present paper deals with the chloride leaching of complex base metal sulphide concentrates of two Indian deposits. A two stage leaching process is suggested keeping selectivity of metal dissolution in view.In the first stage most of the lead and zinc are reacted with dilute FeCI3 (0.3M) solutions at a temperature ono&#176;c where major portion of the lead remains in the residue and zinc reports in solution. After taking out lead chloride by brine leaching, the residue has been treated for copper dissolution. A concentrated FeCI3 leaching at boiling temperature as well as ambient aqueous chlorine leaching have been separately tried to dissolve out the copper from the residue. Based on the results obtained, a flowsheet for the proposed process is presented.

Jan 1, 1981

By Michael Rieber

Among the principal gathering/distribution systems for coal is over-the-road trucking. Where alternative trunk line modes such as barge or rail links are weak or nonexistent, trucks may, particularly for relatively short line hauls, act as substitutes. Their major application, however, appears to be in connection with smaller mines or coal users particularly where terrain problems are significant. Truck use has increased as rail lines have been abandoned or suffered neglect. For example, in 1956 about 38 percent of the coal transported in eastern Kentucky and about 8 percent of the coal moved in western Kentucky went by truck. By 1975, the percentages were almost 77 percent and 26 percent, respectively [4,U-11]. While rail route .limitations and deterioration played a part in the change, increased emphasis on road building, particularly during the 1950&apos;s and 1960&apos;s, and improved truck load capacity and efficiency were also important.

Jan 1, 1977

During the last 125 years, the steel industry has witnessed revolutionary changes in the process of steelmaking. The Bessemer process was the predominant steel production technology during the last two decades of the 19th century. The open hearth process accounted for the lion&apos;s share of world steel production for six decades from 1910 to 1970. With the appearance of the LD process on the industrial stage in 1952, the importance of open hearth process declined and currently the basic oxygen processes are contributing more than 60 per cent of the world steel production. The LD process also led to the development of several other oxygen blown processes such as LDAC, OLP, OBM, QBOP, EOF, Clc.

Jan 1, 1999

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By S. Peterson, E. C. Westman, P. L. Swanson

Coal bumps are brittle, violent failures associated with high stresses and competent host strata. To study bump mechanisms, conditions in the vicinity of a deep longwall mining face in bump-prone strata were monitored using three discrete systems. First, a microseismic monitoring network recorded mining-induced seismic events throughout the mine and surrounding strata. Second, pressure variations and distributions on the longwall shield legs across the face were recorded. Last, tomography surveys imaged seismic transmission properties ahead of the face. Results from the three systems were correlated in an effort to increase understanding of mining-induced stress redistribution and bump potential. An initial, one-week study showed that the correlation between averaged tomogram values and seismically active areas had a coefficient of correlation (R) of 0.89. Further results of these studies demonstrate that the tomography system is capable of imaging heavy shield-leg loading and bump-prone conditions prior to them disrupting the face operations.

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By V. Labiouse, B. Heidenreich

The rebound phenomenon, which occurs during rockfalls when a rock block impacts with a slope surface, is influenced by several parameters related not only to the slope material but also to the block and the kinematics. The paper presents a small-scale testing campaign undertaken at the LMR (EPFL) to better understand and quantify the bouncing of blocks on granular slopes. The influence of some factors related to the ground material, the block and the kinematics is examined. Bei Steinschlägen wird die Flugbahn eines stürzenden Felsbrockens maßgeblich durch den Abprall vom Hang bestimmt. Der Rückprall hängt von verschiedenen Parametern ab, wobei nicht nur das Hangmaterial sondern auch Blockeigenschaften und Kinematik eine große Rolle spielen. Zum besseren Verständnis dieses Phänomens und seiner Quantifizierung werden am LMR (EPFL) kleinmaßstäbliche Versuchskampagnen auf granulären Materialien durchgeführt. Der vorliegende Artikel stellt die Versuche vor und untersucht den Einfluss verschiedener Boden-, Block- und kinematischer Parameter. Le phénomène de rebond qui se présente lors de l’impact d’un bloc rocheux sur la surface d’un versant dépend non seulement des caractéristiques du terrain, mais aussi de facteurs relatifs au bloc et à la cinématique. L’article présente une campagne d’essais sur modèle réduit entreprise au LMR (EPFL) afin de mieux comprendre et quantifier l’impact de blocs sur des matériaux granulaires. L’influence de divers paramètres relatifs au sol, au bloc et à la cinématique est mise en évidence.

Jan 1, 2003