Search Documents

By W. Vickers

SALKOVITZ1 has given a number of useful angles between planes for use with the Laue method in determining the orientation of bismuth single crystals. Bismuth is usually considered as having a face-centered-rhombohedra1 structure with its axial angle 87°34', Fig. 1. A similar figure given by Sal-kovitz appears to be in error in that the angle there marked as 87°34' should be 92°26. The primitive cell is a single rhombohedron of axial angle 570 14. The structure is almost face-centered-cubic and hence high accuracy in measurements is essential if there is to be no confusion in indexing poles or zone axes. It is easier to get this accuracy if zone axes are plotted on the stereogram because they will lie near the basic circle where the net has a more open scale. The zone axes can be read from the film, using a Greninger chart, and can be plotted more accurately than poles. Also, the angles between points near the basic circle can be read more accurately than those between poles near the center. In order to use the zone axes the angles between directions have been calculated from a formula given by Niggli,2 and are given in Table I. Miller indices

Jan 1, 1958

By C. R. Fast

In order to evaluate the ability of a Hydrafrac treatment to effect a sustained increase in well production, data were accumulated on the first 65 wells in 26 fields treated by Stano-lind. Since these data were obtained from such a large number of fields, it is felt that individual well or reservoir characteristics do not affect the overall picture, as might be the case if the study were made in one field or one group of wells in a field. These data are tabulated in Table I and plotted on Figs. 1 and 2. An analysis of Fig. 1 shows that at the end of six months, 75 per cent, or 45, of 60 wells on which data were available showed a sustained production increase. At the end of two years, data were available on 25 wells. Of these, 15 wells, or 60 per cent, showed a sustained production increase. At the end of three years, 55 per cent, or 10, of 18 wells had a production rate greater at that time than before Hydrafrac treatment. The lack of information on additional wells at the end of the third year is primarily a result of the small number of treatments conducted in the early stages of field application

Jan 1, 1952

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By G R. Ballantyne, M S. Powell

A comprehensive Australia-wide survey of comminution energy consumption at copper and gold mines was presented by the authors at the 11th AusIMM Mill Operators’ Conference 2012. The database has been extended to include major overseas mines and used to benchmark comminution energy consumption across the industry. The mines included in this study now represent 15 and 24 per cent of the total global gold and copper production respectively, and almost all Australian production. The comminution energy intensity per unit of saleable metal has been presented in a graphical form similar to a cost curve used in economics. The graphical method has been developed to assess the competitive advantage that can be achieved by reducing comminution energy intensity.This benchmarking tool has been applied to three published case studies to assess its applicability. The first case study indicated that a large reduction in size-specific energy (kWh/t -75 µm) was achievable by converting standard semi-autogenous and ball mill circuits to include high pressure grinding roll and stirred mills. The second case study investigated the metal-specific energy reduction historically achieved by Bougainville with the addition of a preconcentration screening plant. The final case study was conducted by Barrick Gold Corporation and involved incremental efficiency upgrades at three of its gold mines: Cortez, Cowal and Mara North. The application of the benchmarking tool to each of these case studies successfully demonstrated the scale and competitive advantage that was achieved by reducing energy intensity.CITATION:Ballantyne, G R and Powell, M S, 2014. Benchmarking comminution energy consumption for improved efficiency, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to iroth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkinsl reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon-hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group. In this paper, a surface components hypothesis is Proposed to explain the different floatabilities of coals, carbons, and hydrocarbon minerals. The validity of the hypothesis is experimentally supported by the actual floatability, natural floatability, wettability, and adsorbability for neutral oils of coals, carbons, and hydrocarbon minerals tested. The combustible recovery of the flotation results, as used in this paper. was calculated from Eq. 1: P (100-Ep) 100 RWCP Rc= [1] F (100-E,) C, where R, is the percent combustible recovery; F and P are, respectively, the weight of feed and the weight of concentrate or product; E, and Ep are, respectively, the total percent of ash plus moisture in feed and in concentrate; Ru. is the percent weight recovery: and C, and C, are, respectively, the percent of combustible in feed and in concentrate. Except for ash and moisture content, all chemical components of a coal are assumed combustible. The experimental work included studies on flotation, ultimate and proximate analyses, contact angle tests, extractions of bitumen-A with benzene, adsorptions for liquid hydrocarbons, and wetting tests. Most of the flotation experiments were performed in a laboratory Fagergren machine; others were tested in a small Denver machine. The solid feed for the former was 300 g and for the latter was 30 g. The solid materials used for flotation were crushed to —48 mesh. After the mineral pulp in the flotation cell was agitated for 6 min and the pH was adjusted to 7.5 & 0.2 with sodium hydroxide or hydrochloric acid, a petroleum light oil having a viscosity of 5.73 centipoises at 77 °F was added and conditioned for 2 min. Finally, pine oil was introduced and the froth was collected for exactly 3 min. The weight ratio of petroleum light oil to pine oil was kept constant at 1.5 to 1. Tap water was used for all flotation tests. Contact angles were measured with a captive bubble machine. For each coal sample, three specimens were mounted in transoptic mounts and polished with levigated alumina, first on a sheet glass, then on a cloth-covered metal polishing wheel. The polished specimen was first washed with distilled water and wiped thoroughly on a cleaned linen pad, then transferred into the pyrex cell of the captive bubble machine and conditioned for 6 min., and finally measured for contact angles at three or more points. Except where otherwise stated, the induction time for each measurement was 1 min. The contact angle representing each material was obtained by averaging the measurements of three specimens. The linen pad was first washed with warm distilled water, then boiled 30 min in a 2N sodium hydroxide solution, and finally washed with distilled water until no trace of sodium hydroxide could be detected in the decanted solution. The cleaned linen pad was stored under distilled water. Immediately before using, the pad was rewashed and transferred into a clean pyrex petri dish partly filled with distilled water. The glassware and rubber gloves used were cleaned by soaking in sulphuric acid-potassium dichromate cleaning solution, followed by rinsing with distilled water. The polished specimens were handled only by glass forceps. The ultimate and proximate analyses were made in accordance with the ASTM standard procedures for coal and coke. The extractable bitumen-A was determined by weighing 1 g of —100 mesh sample and placing it in a desiccated and weighed ASTM aluminum-extraction thimble. The thimble was placed in condenser hooks and inserted into an extraction flask containing 100 cu cm of benzene. The flask was heated and the benzene vapor was condensed by water coils. At the end of 24 hr of percolation, the thimble was removed, desiccated, and weighed. Loss in weight of sample was taken as bitumen-A and calculated to dry and ash-free basis.

Jan 1, 1955

By James M. Fragomeni

"The mechanical behavior of an Al-Li alloy was studied and related to the extrusion processing parameters, the plastic metal flow during defonnation, the anisotropy, and the microstructure. The extrusion temperatures, strain rates, extrusion ratios, billet temperatures, and extrusion geometries were varied during processing and correlated with the microstructure and properties. The extrusion processing variables were related to the mechariicar behavior, anisotropy, and microstructure through the ZenerHollomon parameter i.e., the temperature compensated strain rate. Based on optical and electron microscopy studies it was found that regardless of the extrusion conditions, the various microstructures for the most part were unrecrystallized for both the as-extruded and the solution heat-treated conditions. Smaller grain sizes were correlated to larger Zener-Hollomon parameters. The extrusion temperature and ratio did not significantly affect the strength or ductility as did the section geometry, which had a large affect on these mechanical properties. The anisotropy of the properties varied substantially when comparing the extruded longitudinal versus transverse grain orientations.IntroductionThe extrusion process also has a substantial influence on: the microsfructure and mechanical properties of a material that is Athens, Ohio, 45701 fonned The plastic defonnation that occurs during the extrusion process alters the grain size, crystallographic texture, anisotropy, subgrain size, dislocation density and various other microstructural features. Often the material being extruded is not homogeneous, therefore variations in the microstructure and properties occur across the cross-section of the final extruded product. The mechanical properties and microstructure can also vary with length since it is hard to maintain a constant temperature throughout the extrusion process. The extrusion temperature often varies from the heat generated during the extrusion process. The demonstration material that was extruded for this .study was an aluminum alloy containing 2.6wt, % lithium and 0.09wt.% zirconium. This alloy was strengthened by heat treatment causing nucleation, growth, and coarsening of coherent metastable o' (Al3Li) precipitates in the microstructure. The ? precipitates which are a consequence 9f artificially aging the AlLi alloy, are spherical, ordered, and coherent with the aluminum matrix and impede the dislocation glide inotion during plastic defonnation. Theo particles grow homogeneously in the matrix, and have the Cu3Au (L 12)"" superlattice crystal structure. Aluminum-lithium alloys are used primarily for aerospace structural applications since they have attractive properties such as a lower density and higher elastic modulus than conventional 2XXX and 7XXX alloys."

Jan 1, 2000

By K. Hasselwander, K. Knabel

"A significant area of Outotec’s business involves fluidized bed roasting. With several decades of experience, more than 300 reference plants and strong R&D capabilities, the company provides several industries with optimum processing solutions. Applications include oxidation and sulfation of sulfides found in copper, pyrite and zinc concentrates. Gold production and de-arsenifying roasting are also within this scope. This paper describes the latest furnace developments and includes novel trends. Moreover, hot and wet gas cleaning systems are examined focusing on unit operations related to the removal of components such as dust, SO2 for sulfuric acid production, fumes, halides, Hg, hydrocarbons, nitrous oxides and metals.INTRODUCTIONGenerally, when defining roasting processes, it can be stated that the respective primary pyrometallurgical reaction is exothermic, of gas-solid nature and relates to a value solid product. These processes are a key focus within Outotec’s scope and include: (i) dead roasting (ii) sulfating roasting (iii) partial de-arsenifying roasting and (iv) two-stage, de-arsenifying roasting.Dead roasting involves the oxidation of a given sulfide, thus allowing for a subsequent leaching process, and has been applied to producing ZnO. Dead roasting of pyrite has also been extensively utilized with a primary goal of producing sulfuric acid. In contrast, sulfating roasting involves converting a sulfide to its sulfate, enabling a selective sulfation of components, such as Cu or Co, and their separation from ferrous components during leaching (produced sulfates are soluble). Partial roasting involves partially oxidating the metal sulfide to its oxide with the simultaneous production of gaseous As4O6, which is handled during gas cleaning. The solid product, containing hardly any As, is rich in S and can be fed to a respective smelter (e.g. in the case of Cu). Alternatively, if the production of oxide is required, a dead roasting step is added after the partial roasting step, with the overall process considered as two-stage roasting."

Jan 1, 2012

By J. Alfred Berger, O. M. Katz

The Zv-Hf-H ternary system was studied between 500° and 900°C at pressures less than 1 atm of hydrogen gas between 1 and 60 at. pct H. A new and unique microgravimentric apparatus was used. Cizanges of slope on pressure-hydrogen composition isothernis delineated phase boundaries. These boundaries separatecl the three regions, a, 0, and y—so designated to correspond to the regions of the Zr-H binary system—from the multiphased areas between them. A eutectoidal decomposition was found with the ß region phase or phases decornposing into a lamellar product on quenching to rool ter,zperatuve. Reproducible decomposition-pressure hysteresis occilrved lnainly at lower hydrogen cornpositions and at lower temperatures across multiplzase vegions between a and 0 and a and y. Tire effects of hqfniur7z on the hydriding charactevistics of zirconiurrz weYe as follows: 1) stabilization of the a and y vegions while destabilizing the 0 region; 2) a/?preciable elevation of the decomposition pressrkres in the multiphase region between the a and /3 field; 3) ~nouenzent of the eutectoid reaction to high te~nperatures; 4) reduction in the total qiiantity of hydrogen absorbed under one atmospheve of Hz p7-essure; and 5) introduction of a split deconzposilion at the eiitectoiclal poinl in pa?? of the ternavy. Assuru~ptions based on an ir-2terstitial vandonl-solulion rtioclel 0.f hydrogen in metals slzowed that the bindit~g energy between solute sites prednnzinatecl at low /i?!dvogen concentrations. However, at high hydrogen contents the entropy was the predorninatlt factor in determining the stability of the Zr-Hf-H al1o.s. This was interpreted to mean a scarcity of filrtlzer itltevslilinl solute sites caused by hydrogen-hydvogen intet-actions in the metal lattice. INTEREST in the reaction of hydrogen with metals has increased in the past few years for the following reasons: 1) the formation or use of high hydrogen potential environments in nuclear reactors; 2) the reaction of hydrogen with alloys in nuclear reactors with the accompanying deleterious effects on the mechanical and corrosion properties; 3) the theoretical implications of thermodynamic data on the theory and rules of alloy formation in the metal-hydrogen systems; 4) the use of hydrogen-containing fuels in rocket engines; 5) the need for a process of making fine metal powders of high-melting reactive metals; and 6) the beneficial impregnation of superconducting alloys with hydrogen. In nuclear pressurized-water reactors, the problem exists of limiting the hydrogen pickup of zirconium alloys which are utilized as fuel cladding, heat shields, and support members. In general, zirconium alloys have good mechanical and corrosion-resistant properties in high-temperature water. However, hydrogen is absorbed from the corrosion reaction between metal and water, greatly accelerating the formation of the corrosion product ZrOz as well as mechanically embrittling the underlying metal. In addition, recent observations1 at zirconium to hafnium welds showed that secondary elements in zirconium can have an appreciable, and somewhat unexpected, effect on hydrogen absorption. This paper lists the thermochemical data in the range 500" to 900°C for the equilibrium reaction of four high-purity Zr-Hf alloys with hydrogen. Phase boundaries and thermodynamic functions are determined while the structural data will be presented in a future paper. In general, the Zr-Hf-H system approximates the well-known, eutectoidal, Zr-H diagram2,3 with modifications introduced through the behavior of hafnium.4,5 The Hf-H system,' published while this work was in progress, provided a consistent trend with the Zr-Hf-H data. PREPARATION OF Zr-Hf ALLOYS Table I presents a complete flow chart of the preparation procedure. The zirconium and hafnium crystal bars were completely immersed in high-purity kerosene and slowly cut into thin wafers. Wafers were then cold-sheared into approximately 1-g pieces, thoroughly cleaned, weighed, and inserted into the furnace. The alloys, B-2, B-4, B-6, and B-8, were then nonconsumable arc-melted under 500 mm of purified argon. Additional purification of the argon was accomplished by melting a large titanium button each time an alloy was re-melted or a different alloy melted. Each alloy button, which weighed 25 g, was remelted four times in an approach to complete homogeneity. Material losses were less than 0.02 wt pct. Alloy buttons were alternately cold-rolled and vacuum-annealed into 10- and 20-mil sheets. Table I1 gives the composition of the four alloys used. Very little elemental segregation existed be-

Jan 1, 1965

By Angela Lorena Cardenas Manosalva

Este trabalho investigou o efeito do hidrogênio nas propriedades do aço 2,25Cr-1Mo-0,25V. As amostras foram envelhecidas a 600°C por 100h e 600h. Uma parte dos corpos de prova foi deixada somente na condição envelhecida e conduzidas ao ensaio de tração. Outras partes dos corpos de prova foram carregados com hidrogênio, sob tensão elástica e sem tensão aplicada, antes de serem conduzidos ao ensaio de tração. Análises microestrutural e fractografias foram realizadas via microscopia eletrônica de varredura (MEV). Os corpos de prova envelhecidos por 600h não apresentaram significante diferença entre as tensões de escoamento e máxima, entre os corpos de prova carreagados com hidrogênio e não carregados (envelhecidos). Os corpos de prova envelhecidos por 100h e carregados com hidrogênio, no entanto, apresentaram uma queda nas tensões de escoamento e máxima quando comparadas com os corpos de prova somente envelhecidos.

Oct 30, 2017

By P. D. Chamberlain, R. M. Nadkarni, D. J. Kinneberg

Introduction The relationship between precious metal miners and gold refiners has been uneasy over the years. Reasons for this uneasiness and lack of trust include technical factors, economics of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates, and sponge produced at the mine site are notoriously difficult to sample. A nonrepresentative sample can be the cause of misunderstanding and distrust. Dote, however, is relatively homogeneous and can be correctly sampled and analyzed with greater reliability. Second, the technology and chemistry of fine gold and silver production is complex and quite different from dote production. Most mining companies are content not to be involved with additional processing steps. From the standpoint of process economies, it is easy to see why miners and refiners are separate groups. Mine location is dictated by the natural occurrence of ore bodies. Heavy capital investment requirements for infrastructure in remote locations usually limits companies to produce the first marketable product from a mine. Beyond that point, the economies of scale and large capital investments for refineries generally dictate that the outputs of several mines be combined to feed a single refinery. The refin¬ing process is so complex that refineries are generally built in larger cities with a skilled labor pool. Therefore, only the largest mines can afford to refine their own output. Lastly, there are cultural differences between the miner and the refiner. The miner, particularly the small gold miner, is by definition a risk taker in a risky business. Refineries, on the other hand, have historically been operated under legal or implied monopolies approved by the government. The government is interested in owning gold, either for currency reasons or because many national mints are major users of gold coins. It is not surprising, then, to find that miners may regard refiners as part of an unresponsive government bureaucracy or, worse, as "city slickers." It is easy for the two groups to distrust each other with these different backgrounds. The interface between miner and refiner does exist and affects nearly all precious metal mining companies and most refineries. This paper discusses the technical and economic aspects of the interface. It points out how both parties can improve the relationship. Technical interface Precious metals selectively dissolve to produce a pregnant solution. They are then recovered from solution by zinc precipitation (Merrill-Crowe process) or by absorption onto activated carbon. This is followed by stripping and electrowinning. At this point, the mining company must decide whether to ship precipitates (or sponge) to refiners or to produce a dote. Some factors the company must consider are the ability to sample precipitates, concentrates or sponge, security of storage, and production rates. An important factor is the incremental cost (capital and operating) of converting precipitates or sponge into dote at the mine. Generally, mines prefer to melt precipitates or sponge to dote to avoid prob¬lems associated with sampling them. There are three types of fur¬naces used by mining operators to melt precipitates to dote. The first and most widely used is a sil¬icon carbide crucible heated ex¬ternally with a gaseous liquid fuel. The crucible is easy to use and slag can be skimmed before pouring dote. This simple system is capable of handling 1 t/a (32,000 oz per year) gold. It could cost as little as $20,000. More complex systems could cost up to $200,000. The second type of furnace is the gas- or propane-fired rever¬beratory furnace. This is usually used only by large-scale opera¬tors in the silver business. Precip¬itates in reverberatory furnaces come in direct contact with the flame. The large volumes of flue gas can carry significant amounts of dust and fume that must be re¬moved from the gas before dis¬charging it to the atmosphere. In the days when the Rand re¬finery in South Africa used reverberatory furnaces, the silver leaving the furnace in the form of vapor and fume was estimated at 2.2% of the total silver charged to the furnace. The gold in the gases was about 0.03% of the gold charged. Most of this silver and gold was recovered in the exhaust gas scrubber system. These scrub¬ber systems can be more costly than the furnace itself.

Jan 10, 1986

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Robin J. Hickson

El Abra is one of the world’s premier copper de-posits. The project is located in northern Chile, 140 km (87 miles) inland from the Pacific coast. It has the same geologic age and structural setting as the world-class Chuquicamata copper mine located 42 km (26 miles) to the south. The current development plan for El Abra extracts798 Mt (879 million st) of high-quality oxide ore. This will require building a solvent extraction/electrowinning(SX/EW) facility that can produce 225 kt/a (248,000stpy) of cathode copper. This will make El Abra the largest SX/EW copper operation in the world, and the world’s seventh-largest copper producer.

Jan 1, 1996

By Dale R. Spangenberg

This Bureau of Mines Information Circular on phosphate is one of a series of minerals availability commodity directories. Nonconfidential information from the Minerals Availability Program data base covering 148 domestic and 103 foreign phosphate properties and deposits has been abstracted for use in this directory. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operational information.

Jan 1, 1983

By Jay S. Gunasekera

Metal parts are traditionally processed by either filly-liquid (e.g., casting) or filly-solid (e.g., forging) state. Semi-solid metal forming incorporates elements of both casting and forging. In 1991, Gunasekera(5) developed a model illustrating the influence of flow stress by the liquid fraction. The result fits Kiuchi's (1979)(7) experimental data quite well. This model assumed the liquid part is surrounded by solid as small pockets inside the material, which is opposite to the real practical situation. Since the melting usually first happens at the grain boundary, it is better to treat the semi-solid material as small metal crystal surrounded by liquid.

Jan 1, 1997

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By William R. Jones, Robert M. Hernon

This report on the Central mining district of New Mexico is the partial culmination of an intensive U.S. Geological Survey effort dating back some 30 years. Robert M. Hernon went to Silver City in 1948 to finish a detailed restudy of the district that had been started in the thirties by Samuel G. Lasky. He was joined by William R. Jones in 1951, and Jones took over as project chief when Hernon resigned to do consulting work in 1953; it was under Jones' guidance that most of the work was brought to completion or nearly so ( 17, 22-24, 26-30). Hernon returned to the Survey in 1958 to work in .the southern Appalachians. Early in 1965 Jones urged that Hernon be reassigned to the Silver City project to help complete the Professional Paper report on the ore deposits of the Santa Rita quadrangle as well as to take over preparation of the report on the Central district for the Graton-Sales volume. This reassignment was approved, and Hernon began work on the present report. By late June he had completed most of it in draft form, and on June 28 Jones and Hernon left Denver for a short trip to Silver City to fill in a few gaps and to reacquaint Hernon with activities in the district, which he had not visited for 12 years. Late in the afternoon of June 29, 1965, as Bob and Bill were 85 miles short of their destination, their jeep collided head-on with a truck that was attempting to pass another vehicle in a cloud of dust. They both died instantly. As the most recent surviving member of the Silver City project (1958-1962), I was given the honorable though rather sorrowful task of putting the Hernon-Jones report "in shape" for publication. Fortunately the manuscript was already in good shape, so that the task has consisted of little more than minor reorganization and editing, and of preparation of the illustrations, abstract, and bibliography. The sections on wall-rock alteration had been left for Jones to complete in the light of his recently intensified interest in alteration geochemistry (25), and it is in these sections only that. the report may fall short, for they have been filled in from a 1958 manuscript by Jones on the ore deposits of the Santa Rita quadrangle that he intended to revise considerably. The shortcomings, however, are largely in the interpretation, not in the field data. As a brief but accurate summary of what was known about the geology of the Central mining district in 1965, this report stands as a fitting testimonial to the scientific dedication of two exceptional men.

Jan 1, 1968

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

By E. C. Truesdale, W. K. Waring

The Research,Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kids of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein' some years ago: ZnO + CO = Zn + CO2 [i] C + COj = 2CO [2] Each of these reactions is dependent upon the other for the supply of CO and COz, respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + He = Zn + HZO 13] C + Hz0 = CO + He U3 While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse Ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction is still the faster. He also says (p. 48), "At temperatures . . . be- -tween 1100' and 1300°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates.'' In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier's statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of ' a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented.*

Jan 1, 1944

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946