Search Documents

The individual or company director who ignores his or her obligations under the Resource Management Act 1991 and under the proposed hazardous substances legislation, ignores them at their peril. Two recent cases in Canada and the United Kingdom concerning environmental offences under similar legislation illustrate the risks well.

Jan 1, 1993

Jan 1, 1934

By E. H. Wells, A. Andreas

New Mexico retained its position as the sixth largest oil-producing state for the year 1937 with a total production of 38,484,630 bbl. This was an increase of 11,680,184 bbl. over the 1936 production of 26,804,446 bbl., or a gain of 43 per cent. The production for Lea County during 1937 was 35,961,056 bbl.; for Eddy County, 2,136,251 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 387,323 bbl. The average daily non-marginal well allowable for Lea County on Jan. 1, 1937, was 92 bbl.; at the close of the year it was 67 bbl. The average daily pipe-line runs were less than the allocations of the New Mexico Oil Conservation Commission, but slightly in excess of the state allowables recommended by the United States Bureau of Mines. The average daily production for the year was 105,437 barrels. The total number of completions in the state was 742, of which 638 were oil wells; 19 hydrocarbon gas wells; 5 carbon dioxide gas wells and 80 dry holes. Of the dry holes, 46 were in proven fields. Of these 46 dry holes, 13 were in the Artesia-Grayburg-Jackson-Maljamar area, Eddy County, two in the Getty Extension field, Eddy County, 11 in the Red Mountain field, McKinley County, three in the Rattlesnake field, San Juan County, and nine in the Aztec-Bloomfield area, San Juan County. There were only eight dry holes in the proven fields in Lea County. Southeastern New Mexico Lea County.—The Monument field was the largest producing field in Lea County, with 10,945,788 bbl., closely followed by the Eunice field with 10,927,929 bbl. The Hobbs field, formerly the largest producing field in Lea County, was relegated to third .place, with 7,292,522 barrels. Drjlling during the year closed the gap between the northern part of the Eunice field and the southern part of the Monument field. The wells in this area were relatively small, because of decreased porosity in the lime. The greatest activity in Lea County was in the Monument pool, with 199 completions, 197 being oil wells, one a gas well and one a dry hole.

Jan 1, 1938

By Persifor Frazer

The ore property of Mr. Augustus bop is situated about one and a half miles south of the New Windsor Station of the Western Maryland Railroad and is connected with the town of New Windsor by the Liberty and New Windsor Turnpike. It is about forty miles distant from Baltimore, and about seven miles west from the county town of Westminster, and a little more northeast from the celebrated Liberty Copper Mines. (See accompanying Map I and 2.) The property comprises about 140 acres, lying principally

Jan 1, 1881

By V. V. J. Sarma

Interpretation of earth resistivity data involves not only obtaining depth to interfaces but also determining the nature of formations from their resistivity characteristics. Moore's method of interpretation envisages obtaining depths to the interfaces alone. A simple method of estimating the true resistivity values of formations by applying Hummel's formula of average resistivities is proposed. The method would increase the interpretative value of Moore's method as originally proposed. For most of the earth resistivity measurements, the four-electrode configuration developed by Wennerl is employed. In principal, the method consists of energizing (Current I) the ground through two outer electrodes and measuring the resultant potential (v) between the two inner electrodes. The configuration is such that the separation (a) between any two successive electrodes is equal. The apparent resistivity (pa) for such a configuration is given by 2p- a (V/I). By increasing the electrode separation (pa vs a) curves are obtained. Ideally, a homogeneous isotropic formation underground has a characteristic resistivity. However, the field conditions do not present such ideal cases. Almost invariably, even in the same geological bed, the physical conditions are widely different at different parts in the bed. It is further shown that the penetration of the current into the ground for a given horizontal electrode separation, a, is roughly down to a depth, equal to a. It is therefore, evident that the apparent resistivity calculated from the field observations is a weighted average of the resistivities of the materials present down to this depth. With some prior knowledge about the relative dispositions of the geological formations and their physical conditions, it would be possible, by resistivity surveys, to obtain characteristic resistivities for these formations. It is, thus, that the apparent resistivity-electrode separation curves enable one to decipher the resis- tivity distribution at various depth levels and therefore the nature of the geological formations present. Both empirical and theoretical methods have been developed for determining resistivity characteristics of the various formations. The theoretical methods proposed by Tagg2 and Roman3 are derived from studies of the potential distribution on the surface due to the presence of layers of widely differing resistivities underground. The more recent methods of Wetzel and McMurry4 and Wetzel and Mooney5 are but extensions of the original Roman method of superposition. These methods suffer from lack of similarity of the actual field conditions with those of assumed conditions in developing the theory. The empirical methods such as the one developed by Gish and rooneY6 depend purely on personal observation and local peculiarities, and are applicable only for those limited areas. Out of the empirical methods, moore's7 cumulative resistivity method is still found to be applicable in several localities of differing conditions. While Reudy in 1945 adduced some theoretical justification for the method (Eve and Keys),8 Muskat9 and Mooney 10 tried to show the lack of theoretical basis for the same. It is, however, observed that the method in practice "forms a valuable means of successfully attacking the apparent resistivity curves which fail to respond to the Gish-Rooney, the Tagg or the Roman logarithmic methods" (Ramachandra Rao). 11 Comparatively good results are also reported by Melbyel2 by employing Moore's method in interpreting the resistivity results obtained for ground water in the city of Gunnison, Colo. MOORE'S METHOD As has already been pointed out, the application of the theoretical methods is time-consuming, laborious and sometimes not applicable for quick and accurate interpretation of the field data. moore7 has developed a quick method for obtaining depths to interfaces by plotting the cumulative sums of resistivities, against the corresponding electrode separations a instead of plotting the usual Pa — a curve. In this process of continuous integration, corrections for small variations in resistivities, arising due to local surface conditions or adjacent layers, are made, while large consistent variations are brought out

Jan 1, 1963

By K Ehrig, J Griffith

An extensive suite of elements are routinely assayed on all resource drill core samples to assist in deposit scale resource definition, local mine scale delineation of ore zones, and ore characterisation for the planning and scheduling of mining and processing of ores at Olympic Dam. This paper discusses a deposit scale geochemical relation that can be used by mine geologists to find more high-grade ore at the local mine area scale at Olympic Dam.A 3D grade shell representing 0.8 per cent Cu was created for a mine area using drill hole assay data. This defined the geometry of the ore zone. The Cu-grade shell was then overlain onto the existing resource block model to evaluate the relationships between the Cu-grade shell, copper and other elements. The strongest correlation was between copper and manganese. The block model showed a dramatic decrease in the concentration of manganese just below the below the Cu-grade shell.Several drill holes that intersected the Cu-grade shell were selected to evaluate the copper manganese relation at the drill hole scale. As expected, the individual drill holes displayed a strong inverse relation between copper and manganese. A geochemical footwall was then modelled representing 0.1 wt per cent Mn. Using both the Cu– and Mn-grade shells, several drill holes were designed/drilled and all hit high-grade copper.For the vast majority of the deposit the inverse relation between copper and manganese is valid; however, in areas with intense chlorite alteration (related to amounts of mafic to ultramafic rocks) this relation is not as strong, due to increased manganese in the rock mass. Even though using the copper manganese relation as a drill targeting method was not always as reliable in a few small areas of the deposit, it demonstrates the value of using existing assay data integrated with the resource block model to discover local mine scale geochemical relationships which can be used to more effectively design drill holes to discover high-grade ore at Olympic Dam.CITATION:Griffith, J and Ehrig, K, 2017. Using existing data to improve the delineation of ore at the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit, in Proceedings Tenth International Mining Geology Conference 2017, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Gwynne

McArthur River Mine is located approximately 50 km south-east of the NT township of Borroloola and approximately 120 km from the Gulf of Carpentaria. The mine hosts a series of layered shallow dipping tabular orebodies, with current reserves of approximately 22 Mt, grading 13.6 per cent zinc, 6.3 per cent lead and 65 g/t silver. Owing to economic considerations, the lower most orebody (No 2 orebody) has been selected for initial mine production. Following the completion of the No 2 orebody, mining will transfer to the lower grade and metallurgically more complex No 4 orebody. The mine employs a total of 235 people throughout the underground and surface areas. The majority of the workforce work a fly-in/fly-out, seven-day- on/seven- day- off roster with 12-hour shifts. Presently, a further 18 contractors are involved in trial mining areas. An apparent dip room and pillar technique has been selected as the primary mining method. Officially opened in September 1995, the current production rate of 1.2 Mt per annum will eventually escalate to 1.5 Mt per annum. Though most production is achieved through the use of conventional loaders, trucks and jumbos, the recent development of methods utilising scrapers, hand held machines and modified jumbos has produced encouraging results in steeper dipping areas of the mine. Initial production has been hindered by several factors including extensive and largely unpredictable faulting, worse than expected ground conditions and difficulties with some mining equipment. Compounded by the relatively thin 3 m ore seam, initial mining resulted in high dilution and poor production. This paper describes the development of unique planning and production systems that were evolved in order to overcome these problems and achieve the targeted production rates and head grade.

Jan 1, 1998

By R G. Jeffrey

The Northparkes, Endeavour 26 orebody is a porphyry copperûgold deposit and comprises a moderately to well jointed rock mass characterised by gypsum veining, the intensity of which decreases with depth. The top 480 metres of the orebody is currently being mined by block caving, the undercut dimensions measuring 196 metres in length by 180 metres in width. Continuous caving was never achieved after the completion of the undercut thus cave inducement techniques were sought to maintain caving so as to safely sustain production. The use of hydraulic fracturing as a cave inducement tool was successfully trialled in December 1997 using existing exploration boreholes located midway up the current lift. Subsequent fracturing campaigns have enjoyed various degrees of success and have yielded in excess of seven million tonnes of ore at a significantly lower cost than conventional cave inducement techniques. Monitoring of both the hydraulic fracture system and the rock mass response has provided considerable insight into the geometry, growth and influence of hydraulic fracture networks above the Northparkes block cave, and has initiated additional research into the use of hydraulic fracturing in other mining methods.

Jan 1, 2000

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

By Byron A. Baker

The Bureau of Mines used a windowed cell to measure the phase-boundary pressures of two related series of gas-condensate fluid mixtures. Normal butane was added to the mixtures incrementally to determine its effectiveness for lowering phase-boundary pressure. All the experimental data were correlated, so that the pressure required to maintain light oils mixed with natural gas in the single phase may be computed for secondary recovery applications. The heavy hydrocarbon parts of the mixtures were distillation fractions of a Gulf Coast condensate. Intermediate normal hydrocarbons in the butane-heptane range and natural gas were added to the fractions in selected proportions, so that phase-diagram pressures of 26 fluids were actually studied. The experimental range of temperatures was 50° to 280° F. Two correlations were developed to represent phase-boundary pressures by means of a polynomial. Independent variables represent natural gas content, disparity of properties of components comprising the mixtures, and temperature. A fourth variable, for one correlation only, was the quantity of normal butane added to the original mixtures. The latter correlation with four independent variables contains 15 coefficients and is estimated to be accurate to 135 psi.

Jan 1, 1973

By Huimin Lu, Zhijiang Gao

Reduction reaction can happen among Al, V2O5 and TiO2 powders. Al can deoxidize metal V and Ti from the metal oxides. The electric igniter can be used to trigger the reduction. The reaction between Al and V2O5 is very intense and release large amounts of heat, but the heat which is needed to initiate the reaction between Al and TiO2 is not enough. These two reactions have been initiated first and V-Al and Ti-Al alloys can be obtained with a higher metal recovery percent. Through adjusting the ratio of Al, V2O5 and TiO2 powders, the system which combines these two reactions can ensured enough heat to react. KClO3 is added to the system, as the ignition agent, in order to make the reaction much complete. Finally, Ti-Al-V alloys can be obtained and need remelt to adjust the constituents.

Jan 1, 2016

By Daniel T. Eyde

The U.S. Geological Survey (USGS) estimates world production of natural zeolites to be 2.7 Mt (3 million st) in 2013. China ranked ?rst with 2 Mt (2.2 million st), followed by the Republic of Korea at 230 kt (253,000 st) and Turkey at 50 kt (55,000 st). Japan?s production is reported to have increased as a result of zeolites, reportedly low grade local mordenites, being used to treat the low-level radioactive contaminants in the areas surrounding the damaged reactors at the Fukushima Daiichi power plant. China and other countries? high-volume, low-value construction applications, which include dimension stone, pozzolans and lightweight aggregate, are also included in production. This means the production data does not accurately indicate the quantities used in high-value added specialty applications. Consumption in the United States, according to USGS estimates, increased slightly, to an estimated 71.3 kt (78,400 st). Domestic uses for natural zeolites were, in decreasing order by tonnage, animal feed, pet litter, cement (primarily down-hole cement applications by the drilling industry), water purification, odor control, waste water cleanup, fungicide or pesticide carrier, gas absorbent, fertilizer carrier, oil absorbent, desiccant, catalyst and aquaculture. The six leading uses accounted for more than 70 percent of the domestic natural zeolite sales tonnage.

By Eugene T. Sheridan

The 25th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, disclosed that 79 companies produced and sold peat from 81 operations in 21 States in 1958. Peat is a carbonaceous deposit, formed under water or in a water-saturated environment from plant material. It is the first stage in the development of coal and, when properly dried, can be used as fuel. Although 98 percent (estimated) of the total world production is used for energy purposes, the status of peat in the United States is somewhat unique in that none is used for fuel, and practically all is consumed as an agricultural product, chiefly for soil improvement purposes. The domestic peat industry has expanded rapidly since World War II, and production in 1958 was 327,813 net tons valued at $3,445,767. More than one-half million ton of peat was consumed in the United State in 1958, however, as 269,096 tons was imported.

Jan 1, 1959

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development.

Jan 9, 1953

By H. X. Yan, J. X. Zhang, F. S. Niu

"The analysis on influencing factors of hydraulic conditions in fine hematite flocculation, such as stirring speed, stirring time and axial distance of particle size and fractal dimension of floc was investigated. Furthermore, response surface methodology(RSM) has been applied according to the Box-Benhnken center-united experimental design principle to optimize parameters of hydraulic conditions as a response index to indicate the fractal dimension of floc. The results show that when the agitation speed is 900r/min, the axial distance is 2.0cm, and the stirring time is 3.0min, the particle size reaches the maximum value of 35.44µm and the fractal dimension is 1.6594. The interaction between the axial distance and the stirring speed is highly significant, but the interaction with the stirring time is not obvious. The experimental data and model predications match well, which indicates that the established model has high accuracy and practicability. INTRODUCTION With the exhaustion of iron ore resources that are easy to be mined and the vigorous demand for iron and steel, the exploitation and utilization of fine-grained embedded iron ore resources have drawn attention from the industry and the government [1~2]. Flocculation flotation is one of the effective methods for separation and recovery of fine granular minerals. In 1975, the method was first applied and succeeded in Tilden Concentrator, USA. Flocculation and desliming became the key technology of the Tilden to raise its annual treatment capacity from 4 million tons to 8 million tons at that time [3 ~ 4]. In 2008, the selective flocculation and desliming-reverse flotation technology was successfully used to treat 2.8 million tons of Qidong iron ore. Under the conditions of 28.36% raw iron grade and 98% grinding fineness -0.038 mm, the ideal index of 62.5% iron concentrate grade and 68% recovery was obtained [5]. Dr Kitchenner of the Royal College of Mining and the Ore Processing Research Group of Wallenstein Laboratory first proposed the use of flocculation to separate minerals. After that, many scholars conducted a great deal of theoretical and practical researches, but mostly they focused on chemical theories, mathematical models and selectivity differences in the flocculation process, while the research on the influence of the pulp flow state on the separation effect in the flocculation process started later [6~9]. The results show that the motion of the agitated flow field has a significant influence on the formation of flocs. The fluid morphology will change with the change of hydraulic conditions. The change of fluid morphology will not only affect the movement behavior of particles, but also change the action of chemical agents on the surface of mineral particles[10~12]."

Jan 1, 2018

By E. H. Denny

A most interesting safety record has been made by the Colorado Fuel and Iron Co. s. Robinson ho. 1 mine located at Walsen, Cola. Mr. J. L. McBrayer has been superintendent of the Robinson No. 1 and 2 mines for the past 2 1/2 years, and Mr. David Muir has been foreman of the Robinson No. 1 mine since June, 1913. The last fatal accident at Robinson No. 1 mine occurred on July 27, 1915, and the tonnage produced at this mine since July 28, 1915, has been as follows:.

Jan 1, 1929

By Stuart Ratcliffe, Denis Kidby

The development of Vitrokele™ Technology over the last 10 years is reviewed with reference to mine site piloting and com­mercial applications. The first mine site piloting was conducted in Australia in 1989 followed by a further six continuous site trials in Australia, Canada and the USA. These major pilot plant studies are complemented by over 50 laboratory scale batch and pilot testwork programmes. The first commercial plant using Vitrokele™ Technology was the Connemara project commissioned in Zimbabwe in 1995. Subsequent to this, three commercial scale projects have been designed using Vitrokele™ to recover precious metals, base met­als and cyanide. The various projects are discussed with relation to the differ­ing flowsheets applied to each particular case.

Jan 1, 1998

By David Keys

THE object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abun-dant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer,- but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite. No trace of magnetite was found. Fig. 2 is a photo-micrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titanium, 19.26 per cent; iron 45:41 per cent.

Jan 1, 1936

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013