Search Documents

By Dany Pelletier, Yeves Breau, Ahmed Bouajila, Claude Gagnon

"In flotation circuits, direct measurement of the volumetric flow rate delivered by electromagnetic flowmeters is often difficult to obtain particularly due to piping and flow constraints. However, on-line material balance calculation could offer a reliable alternative to flow rate sensing. This paper describes an on-line material balance software package as applied to a copper flotation circuit for mass flow rate estimation mainly based on the output of an x-ray fluorescence onstream analyser. Rule-based procedures for the management of the main calculation modules are designed and integrated to a Comdale expert system. Attempts to diagnose the flotation process from mass flow rate data are also discussed.INTRODUCTIONThe need for improved process diagnosis, control and optimisation has become more evident for the mineral processing industry in the last decade. Therefore, new process variables need to be inferred or measured particularly in highly multivariable processes such as flotation. This process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and chemical characteristics of the ore and due to some irregularities in manual process operating procedures.A flotation circuit scheme is always a complex network counting more than two dozens of slurry streams. Information about those streams (%solids, metal content analysis, and flow rates) are important for process diagnosis, performance evaluation control and optimization (1,3).On-line sensing instruments such as x-ray fluorescence (XRF) on-stream analysers (OSA), gamma density gauges and electromagnetic flowmeters have been developed for the measurement of those variables. Unlike the other variables, stream flow rates could be determined by different ways:"

Jan 1, 2000

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By Gregory M. Rumbaugh, Christopher Mark

"The proliferation of unconventional gas well development in the Northern Appalachian coalfields has raised a number of mine safety concerns. Unconventional wells, which extract gas from deep shale formations, are characterized by gas volumes and pressures that are significantly higher than those observed at many conventional wells. The gas is composed largely of methane as well as other hydrocarbons. Hundreds of planned and actively producing wells penetrate protective coal pillars or barriers within active mine boundaries, including chain pillars located between longwall panels. Gas released from a well damaged by mining-induced ground movements could pose a risk to miners by flowing into the mine atmosphere. The mining-induced ground movements that may cause well damage include conventional subsidence, non-conventional subsidence (e.g., bedding plane slip), pillar failure, and floor instability. This paper describes the known risk factors for each of the four failure mechanisms. It includes a framework that can guide the risk assessment process when mining takes place near gas or oil wells.INTRODUCTIONSouthwestern Pennsylvania has served for centuries as a producer of coal, oil, and natural gas. Coal mines were first developed in the Pittsburgh Coal Seam in the 1760s, with the first recorded mine in 1761 being the Fort Pitt Mine (Edmunds, 2002). Natural gas was introduced to the region when the Haymaker Well in Murrysville, Pennsylvania experienced a blowout on November 3, 1878. Although it was originally drilled prospecting for oil, it produced an estimated 30 million cubic feet per day of natural gas. Without well controls or pipeline infrastructure in place, it burst into flames and lit the night sky for over a year. Soon after, the Penn Fuel Company continued development of the Murrysville gas field and is credited with making Pittsburgh, Pennsylvania the first major city in the U.S. to have natural gas supplied for home and industrial uses. “Natural gas is king in Pittsburgh,” proclaimed an October 18, 1885, article in the New York Times headlined “Value of Natural Gas, Its Use Clarifies the Atmosphere at Pittsburgh” (AOGHS, 2018). By the early 1900s, coal, oil, and natural gas production had reached the southern extents of Pennsylvania in Greene County. The county had first produced oil in 1886, and shortly after began producing natural gas in 1890. By 1906, over 1,300 wells had been drilled (Stone and Clapp, 1906)."

Jan 1, 2019

By M. Maldonado, J. A. Finch

"A flotation bank consists of a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three strategies for optimizing bank performance: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data is analyzed in respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.INTRODUCTION Flotation is used to separate valuable minerals from each other and from gangue. To reach a target metallurgical performance, usually assessed in terms of concentrate grade and recovery, feed is passed through stages such as roughing, cleaning and scavenging. All these stages comprise serial arrangements of flotation cells known as banks, lines or rows. Although a bank is the simplest interconnection of cells in a circuit, i.e. the tails of one cell is the feed to the next cell down the bank, how to operate each flotation cell in a way that the whole bank performance is optimized remains a challenge. Significant efforts have been made towards understanding the effect of operating variables on the flotation performance of an isolated cell (Lynch et al., 1981; Finch and Dobby, 1990; Gorain et al., 1998). However in the case of banks the variables that can be manipulated increase with the number of cells in the bank and the problem of how to manipulate them to achieve optimum performance is difficult even disregarding variation in ore characteristics (Lynch et al., 1981, p. 16). In general, the more manipulated variables available the better for optimization purposes, however without clear guidance how to effectively use them it becomes an “embarrassment of riches”."

Jan 1, 2012

By AIME AIME

WILLIS McGERALD PEIRCE-"Jerry" to his host of friends, and on that account a hit of a puzzle to those who have known him only as "W. 14."-a native of Buffalo, educated at Penn State College, Illinois: and Yale universities, has bee11 associated throughout all of his professional career with the New Jersey Zinc Company. Jerry has served successively as investigator, section chief, and division chief in the research department of the company and has just been promoted to chief of research.

Jan 1, 1937

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By Charles Jones

Discussion of the paper of CHARLES COLCOCK JONES, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1887 to 1898. D. A. LYON, Salt Lake City, Utah.-For some years I have been interested in the iron-ore deposits of the Pacific Coast, and I feel very much indebted to Mr. Jones for the information he has given us on this subject. I think that we are also very much indebted to him for having presented this paper, as he has given us reliable data in shape of facts and figures, which is just what we need in considering whether or not it would be commercially feasible to attempt to establish an iron and steel industry on the Pacific Coast. Personally, due to lack of market, I do not think it is a commercially feasible proposition at the present time. Mr. Jones states that pig iron can be produced on this coast as cheaply as it can be produced in Pittsburgh. Even. so, what can be done, with it after it is produced? To begin with, iron produced on the. Pacific Coast has to compete with iron produced in China. Last year I had occasion to investigate the subject of the market for iron and, steel on the Pacific slope, and found that it was possible for the producers of Chinese iron to sell it for much less than the price for which iron can be produced in the West, and also for less than eastern pig iron is now sold for, even when shipped through the Panama Canal. I was informed that the agents for Chinese iron had instructions to sell it for $1 or $2 less per ton than that asked for other irons on the market. Of course, I realize that the competition of Chinese iron may not be important, but even if it is not, and even though pig iron ,can be produced at the cost given by Mr. Jones in his paper, I do not see any immediate chance of its being so produced, due to lack of market. C. C. JONES, Los Angeles, Cal.-Mr. Lyon is right. It is a fact that Chinese pig is being sold in San Francisco on some large contracts at $18.50 a ton, while $19 is the usual price. We ought to produce iron. on this coast at $14. Personally I do not think Chinese iron is ever going to be an important factor. It is a bugbear out here now. You are not going to have much Chinese pig iron in .this country. Our little friend Japan is going to absorb everything it can. The price of Chinese pig iron at $18 is about as low as it will ever get. If we can show you that we can produce this iron here at the same price as at Pittsburgh, I. think you will have a good opportunity to compete with anything China or India can ever do. Costs there are very low now. They are going to come up by leaps and bounds in the next few years. The labor cost over there may be very low now, but I. have seen some men from there quite recently

Jan 12, 1915

By Nilson Nedes de Paula

Este trabalho visa apresentar os resultados de um estudo de correlação envolvendo concentração magnética nas escalas bancada-piloto e piloto-industrial. Os testes que sustentam este estudo foram realizados no CPT (Centro de Pesquisas Tecnológicas da Vale). A correlação entre as escalas piloto-industrial tende a ser direta, uma vez que, concentradores magnéticos piloto possuem os mesmos mecanismos de atuação de um industrial. Por outro lado, entende-se que a correlação entre as escalas bancada-piloto não seja tão direta assim, necessitando de um entendimento/conhecimento maior para descrevê-la. Aproveitou-se este trabalho também para estudar uma forma de melhorar o modelo atual utilizado pelo CPT em interpretações mineralógicas voltadas para concentração magnética. A metodologia deste trabalho foi dividida em seis etapas distintas: escolha das amostras, amostragem industrial, caracterização das amostras, interpretação mineralógica, testes piloto, testes de bancada e análise de correlação. Em relação aos resultados, este trabalho confirma a interpretação mineralógica como uma boa ferramenta para estimar recuperação mássica e qualidade de concentrado em processos de concentração magnética, e que modelo utilizado atualmente pelo CPT apresenta melhores resultados em relação à modificação proposta neste trabalho. Os testes piloto apresentam resultados praticamente idênticos aos resultados da industrial, confirmando que a correlação entre as escalas piloto-industrial é direta. Por fim, este trabalho confirma que é possível correlacionar os resultados de bancada com os resultados da piloto. Os gráficos de correlação apresentam R2 superior a 0.77, podendo se basear na utilização de equações de regressão para estimar resultados piloto, a partir dos resultados de bancada. Entretanto, entende-se que é necessário realizar teste complementares, uma vez que, o espaço amostral (número de amostras estudadas) foi pequeno.

Aug 1, 2018

By Jesus P. Manzano

The report of which this paper is a summary was made in 1890 for the Compania Investigadora Mexicana y Americana. Since the region examined covers 900 sq. kilom., chiefly of wooded arid rocky hills, almost without roads, and for the most part uninhabited, While the examination had to be made in two months, of which period more than 15 days were continuously rainy, I need not say that this account is not complete and thorough. I. Geography and Topography. The center of this zone, 19 kilom. SW. of San Luis Potosi, is situated in lat. 21° 24' N., and long. 2° 3' W. of Mexico City. The altitude ranges from 1866 m. (that of San Luis) to . 2816 m. (that of the Realito mountain), in the Sierra de Sail Luis. The topography is hilly—partly wooded, partly bare. The principal more level areas are the Bledos valley on the south, and portions of the haciendas of Tepetates, San Fran cisco and Santiago, on the west. The water-supply is scanty. The two streams that cross the Zone, the Santiago and Bledos rivers, carry water nearly the year through, though much reduced in the dry season. Other streams are torrents of less importance. All the waters of the valley and Sierra of Sail Luis arc absorbed or sink, not passing beyond Soledad de los Ranchos. The Continental di vide is within the Zone, some waters going west to the Pacific, others east to the Gulf of Mexico. II. Geology. Concerning the geology of this district I condense the fol lowing from the memoir, Las Minas de Guanajuato, prepared for the Minister of Fomento by Senor Pedro Lopez Monroy, mining engineer, with which I am entirely in accord. He says, ill substance:

Jan 1, 1902

(This list includes only those who have entered military service within the past month, or whose entry has only recently become known to us; it also includes a few names of those whose titles or assignments have been changed within the month. The last complete list was printed in Bulletin No. 131, November, 1917. A complete Honor List is maintained in the reception room at the office of the Institute.) BANKS, HAROLD P., 2d Lieutenant, Ammunition Train, 2d Division, U. S. A. BARKER, L. M., Co. B., 62d Infantry. BENHAM, W. M., Sergeant, Co. H, 158th Infantry. BOUDWIN, WALKER J., Co. C., 25th Engineers, Camp Devens, Ayer, Mass. BOWLES, MARTIN F., 2d Lieutenant, Co. B., 355th Infantry. BURG, ROBERT S., Instrument Sergeant, Headquarters Co., 340th Field Artillery, N. A. CHALMERS, JOHN W. P.; Signal Depot, Royal Engineers. CHETNEY, P. C., Corporal, 340th Field Artillery, Headquarters Co. CLARK,. WILL L., Federal Fuel Administrator for Arizona. COFFEY, George W., Lieutenant, Engineer Section, Officers' Reserve Corps.

Jan 1, 1918

By D. A. Riva

"The Line Creek Project is located in southeastern British Columbia, approximately 25 kilometres north of Sparwood. The design is to produce a total of2.7 million tonnes of coal annually. This is made up of1.4million tonnes of thermal coal and 1.3 million tonnes of metallurgical coal.Construction commenced in the spring of 1980 and mining operations began in July 1981. The thermal processing plant, maintenance and dry facilities, as well as extensive road and bridge construction, were completed in early 1982. A collective agreement was signed with the International Union of Operating Engineers, Local 115, in June 1981.The first unit train left Line Creek on February 18, 1982 with a load of thermal coal bound for the Ssangyong Corporation in Southern Korea. It was the start of a ten-year contract to supply 350,000 tonnes annually to fire their cement kilns. Additional contracts for 750,000 tonnes will fuel the boilers of Korea Electric Company's San Chon Po and Go-Jeong power stations. Metallurgical coal shipments are scheduled to leave the Roberts Bank port in Vancouver in April 1983.Tracking an introductory presentation given at the 1981 CIM Annual General Meeting in Calgary, this paper highlights the salient developments by which ""The Line Creek Project"" has progressed during the past year to the"" Line Creek Operation"". Line Creek has com e on stream as scheduled and will meet all contractual commitments pertaining to timing, volumes and quality for thermal coal. The first train load left the plant in mid-February, and the first boat load to Korea departed Roberts Bank in mid-April. Metallurgical coal deliveries will commence in April 1983."

Jan 1, 1982

By Juan Mayta

Dada la situación actual y escenario post COVID-19, es fundamental adoptar estrategias de Gestión Colaborativa e Integrada de Proyectos, este artículo es el resultado de la aplicación de Virtual Design Construction (VDC) y Building Information Modelling (BIM) en la etapa de Diseño de un proyecto de reemplazo de Equipos Críticos en la Parada de una Planta concentradora de Cobre (Cu) para Sociedad Minera El Brocal, operación minera ubicada en Cerro de Pasco, Perú.

Sep 29, 2023

By Fernando Altamirano, Karim Batallanos

El presente trabajo técnico es el resultado de la visión integral del negocio donde es prioridad la seguridad de las personas. El sistema de control preventivo de ingeniería Stockpile Safety, minimiza la probabilidad de un accidente grave por el hundimiento de tractores que realizan labores de movimiento de material sobre la ruma de gruesos. El sistema puede indicar en tiempo real la zona de riesgo dentro de las cabinas de los equipos auxiliares y además genera una alerta e la sala de control principal (doble aseguramiento).

Sep 29, 2023

By A Hamanaka

EGAT Mae Moh Lignite Mine in Thailand produces about 16 Mt of lignite annually from open-cut mining. The coal is used to generate 2400 MW of electricity. In the near future, however, the coal must be extracted from underground at 400 - 500 m deep from the surface. The problem is the thickness of the coal seams. There are two coal seams that are about 25 m thick with 20 - 25 m of interburden between them.In order to investigate thick seam mining systems and propose a new mining system in ultra-thick coal seams in Thailand, a joint research group was established by Japanese and Thai researchers and mining engineers in early 2009. This paper describes conventional underground mining systems and underground coal gasification for thick coal seams and discusses the applicable coal mining systems to this mine. Then, this paper proposes an innovative underground coal mining system for thick coal seam, ‘eco-friendly underground coal mining system which consists of the utilisation of flyash and CO2 storage’.

Nov 22, 2011

By Linneas W. Laage

The purpose of this report is to document the fire experiments conducted at the Waldo Mine, NM during March 1990. The U.S. Bureau of Mines is concerned with improving and validating the predictive capability of the mine ventilation and fire simulator, MFJRE. To accomplish this, fire experiments were conducted at the Waldo Mine and temperature profiles were developed as functions of time and distance from the fire. These tests then provided data for verifying the heat transfer model in the MFIRE mine ventilation and fire simulator. An initial analysis of this data indicates that it will serve this purpose well. This report summarizes the data obtained during six fire tests at the Waldo Mine.

Jan 1, 1994

By Gregory B. Poole

As part of a $3.5 billion program to improve the antiquated waste water system in the city of Atlanta, the Nancy Creek Tunnel is being constructed across the northwest portion of the city. This tunnel is over eight miles long and is being constructed using Tunnel Boring Machines (TBM) for the majority of the tunnel and conventional drilling and blasting for three shafts, starter and tail tunnels and four connecting tunnels, totaling 2400 feet in length. An extensive public relations program was developed for this project. A group effort by the owner, engineer and contractor produced a public relations program that both informed and educated the public of the anticipated perceptions and effects of the blasting and TBM activities.

Jan 1, 2005

By K. Zeidler, T. Schwind

The Fort Canning Tunnel, Singapore, is an approximately 50 feet (15m) wide vehicular tunnel under shallow ground cover that has been constructed according to the principles of the NATM. Its shallow location in soft ground combined with a high groundwater elevation in close vicinity of historically important features called for special design considerations combined with a rigorous monitoring scheme. Surface, sub-surface and in-tunnel instrumentation was installed to monitor the performance of the ground and tunnel support during construction. Comparison of actual reading data with the results from the computer modeling carried out during the design phase is provided in this paper.

Jan 1, 2007

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

Discussion of the paper of A. P. WATT, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 130, October, 1917, pp. 1476 to 1563. THE CHAIRMAN (0. M. _BILHARZ, Miami, Okla.).-Mr. Watt's reference to sorting or hand-picking of the ore in the lead district, which is being introduced at Mine La Motte, is especially interesting. I believe, from my former experience in the district, that hand-picking should be practised to some extent by all the companies in the Lead Belt. I know that a great many thousand tons containing only very small amounts of lead are passed through the mills, which, of course, is not to the advantage of milling machinery. That procedure may be Warranted at times of high prices, but I think that hand-picking should ordinarily be adopted to some extent: ERNEST GAYFORD, Salt Lake City, Utah.-On page 1525, speaking of the settling of slime previous to treatment either on slime tables or by flotation, Mr. Watt states: "The settling area allowed per ton of dry slime varies from 11 to 16 sq. ft.-an average for the district would be about 13 sq. ft. of settling area per ton of dry slime. This figure applies when the, discharge contains 20 per cent. solids." Mr. Ramsey, of the Dorr company, is here and I would like to ask him whether a settling area of 13 sq. ft. per ton of dry slime per 24 hr. is not considerably above the average area of Dorr settling tanks, and whether 20 per cent. solids is not above the general dilution for that' capacity? I should also like to know what is the general average on slimes of that character. E. R. RAMSEY, Denver, Colo.-An allowance of 13 sq. ft. per ton does seem rather large. I am not familiar with the settling characteristics of the dolomitic gangue, but as an average over the country, I should say that 6 or 7 sq. ft. would be nearer correct for discharge at that consistency. L. A. DELANO, Bowie Terre, Mo.-We have had an opportunity to try our tanks at the highest capacity, and-find that by thickening the slime to 30 per cent. solids we average 12 sq. ft. per ton of dry slime. ERNEST GAYFORD.-DO you find any definite ratio between the thickness of the discharge and the settling capacity of the tank? Do you consider that the tank has a larger capacity if the discharge is 3 to 1 than if it is 50 per cent. solids? L. A. DELANO.-I think it has greater capacity with the thinner discharge. It depends a good deal on the density of feed to the tanks; in our case the feed contains 2.5 per cent. solids.

Jan 1, 1918

By E. L. McHugh, R. T. Mayerle, J. M. Girard

Ground control problems at surface mining operations can occur for a variety of reasons. Stress, gravity loading, rock strength, geology, pore pressure, weather effects, underground workings, and many other factors contribute to slope instabilities that range from small rock falls to massive slides of material. While some of these failures can be predicted or controlled by preventive measures, each year many completely unexpected failures occur. Current methods for monitoring generally involve measuring displacements at a few, selected points in and around the suspected area of instability. While most of the displacements along these points will be in a downslope direction, freeze-thaw cycles of water-filled joints, horizontal stresses or pressure, buoyancy in saturated soils, human measurement errors, or other situations can produce deformation in almost any direction, even without any instability in the slope. Determination of which, if any of the observed movements represents a potential hazard is essential. Because of the enormous surface area of many large open-pit mines, several varieties and scales of instability can occur. Small, unexpected rock falls may indeed be more hazardous than a massive failure that involves slow displacement of material over a longer period of time. Complete vigilance to detect all small potential falling blocks is neither feasible nor economical and certainly is not attainable using today's most common point displacement monitoring techniques. As part of an on-going study at the Spokane Research Laboratory, several new methods for monitoring slope instabilities are being investigated. This paper describes the potential adaptation of systems such as interferometric synthetic aperture radar, imaging spectroscopy, and time-domain reflectometry, to slope monitoring and design.