Search Documents

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920's in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Nikkam Suresh

Dense medium cyclones have been in use for washing coarse and small coals for more than 50 years. There have been modifications in its design and today these units have become indispensable for washing of Indian coals possessing difficult washing characteristics. About 53 percent of the Indian coals (coking and non-coking) are being washed in jigs, about 38 per cent are washed in dense medium cyclones while the remaining 9 per cent is treated in other units like Barrel Washers, Heavy Media Baths and Drum Separators etc. The present paper deals with the attempts made for design of industrial Dense Medium Cyclones for enhanced coal recovery. Two industrial units of 500 mm diameter and 650 mm diameter were designed with their washing capacities being 200 m3/hr and 350 m3/hr, respectively. The results of the pilot tests conducted on 500 mm cyclone treating very high Near Gravity Material coals crushed to -3.0+0.5 mm gave an ash reduction of up to 19.5 percent with the new design i.e., from a feed ash of 34.5 percent to 15.06 percent in clean coal with an appreciable yield of 45 percent in one stage.

Sep 1, 2012

By Viswanadham B. V. S., Babu K. V

Wind energy is one of the most economical renewable energy sources. In order to support wind turbines onshore or offshore open-ended monopile foundations are widely used. Unlike conventional structures, wind turbine foundations experience a large magnitude of lateral loads in the order of 20 % to 30% of total vertical loads. The presence of soft clayey layers at shallow depth along the coastal region, offers lesser lateral load resistance to monopile foundations. One option to enhance lateral load capacity is by introducing fins to the outer surface of the monopiles. Studies pertaining to lateral load response of finned piles in clayey soils are very sparse. This paper presents some of the numerical model studies on the lateral load response of monopiles and finned piles in soft and stiff clay. In the present study, three-dimensional finite element analyses were performed on monopiles as well as finned piles. Analyses were performed in clay with different consistency varying from soft to stiff. Pile material is mild steel for all analyses. The pile section modeled as linear elastic material whereas soil was modeled as Mohr – Coulomb constitutive model with non-associated flow rule. Monopiles and finned piles having four and eight fins with different fin sizes and configurations are considered during the analyses. Finned piles advantage over monopiles to resist lateral load is highlighted in the present study. The results have shown that fins are effective to enhance the lateral load carrying capacity of monopiles and also it reduces the bending moment in monopiles for a given design load.

Sep 1, 2022

By J de Witte

When used in suitable ground conditions, rock bolts can have advantages over other permanent tunnel lining solutions. Permanent rock bolts offer flexibility in tunnelling profile and rapid rock bolt installation can enable time and cost savings. There are also disadvantages when considering the suitability of rock bolts for permanent support installations. These generally concern achieving the specified durability requirement over the specified design life. By investigating alternate approaches to rock bolt installation, quality assurance (QA), monitoring and design life it may be possible to alleviate some of these concerns.The design and construction benefits that can be realised through the use of rock bolts are primarily related to reducing project program time. This time reduction could be realised if rock bolts are considered as a permanent solution, with the installation being completed as a part of the primary excavation cycle. Any reduction of the program could allow direct and indirect cost savings and in the case of a major project, allow the revenue stream to be realised earlier.Currently ambiguity exists where the treatment of rock bolts as permanent support components is inconsistent with that of (often identical) ground anchors, as utilised in stabilising cut and cover structures. The ground support design process, implementation and testing are generally similar, though the acceptance of rock bolts as long-term support elements is treated differently to ground anchors in technical specifications.This paper discusses some of the benefits available through the use of rock bolts. It offers different solutions to the concerns surrounding durability, including alternate approaches to installation, Quality Assurance practices and monitoring solutions. The selection of an alternate design life is also investigated as another means of alleviating concerns around long-term durability. The paper will also provide an indication of savings that could be expected through the use of rock bolts as part of a long-term support system.

Mar 8, 2011

By C J. Greet, J Kinal, C Hitchen

Following the successful completion of a marked ball test defining the potential wear benefits the high chrome alloys may offer against forged steel, as well as laboratory test work investigating changes in pulp chemistry and improvements to metallurgical performance, a plant trial was commissioned at NewcrestÆs Ridgeway concentrator. The paper briefly describes these results.Newcrest decided to convert their media charge by the top-up method. To monitor the trial a sampling protocol was put in place whereby the pulp chemistry was monitored before, during and after the purge. The metallurgical shift data was analysed using various statistical methods to determine if the metallurgical performance had improved with the change in grinding media. While the analysis indicated that the metallurgy had improved, not all of the benefits could be assigned to the change in grinding media alone. However, the combination of reduction in media wear and the increases in copper and gold recoveries suggested that it was economically viable to operate with high chrome grinding media.As with many trials of this nature the prevailing economic conditions are fluid and a decision was made to revert back to forged steel grinding media in an effort to reduce operating costs. It was further agreed that Magotteaux could monitor the pulp chemistry and metallurgical changes in this reverse trial to confirm the results observed in the earlier conversion to high chrome grinding media.CITATION:Greet, C J, Hitchen, C and Kinal, J, 2012. Conducting high chrome grinding media trials at NewcrestÆs Ridgeway Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 56-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By E Philippa, J Vitanza, C Hawtin, B Miller

B Miller , E Philippa , C Hawtin and J Vitanza

Mar 22, 2022

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By G. L. Pedroti

With the development of industrial processes and the consequent emergence of numerous products that quickly become necessities, industrial activity has acquired an essential character today. Although its importance is unquestionable, industrial activity is responsible for generating quite a large number of residues, with different shapes and characteristics. It has been observed, in particular the grits (Kraft process in the cellulose industry) and the residue from the processing of granite. And, given the importance of Portland cement as a building material, its vast employment and waste properties that resemble components of the clinker, it was decided to produce cementitious compounds from these industrial wastes. The residues were subjected to mineralogical, chemical, physical and morphological. And, the mixing ratio between the residues in the 70% and 30% grits residue granite was sintered at 1250 ° C furnaces to burn threshold of 6 hours forming new compounds observing tri-calcium aluminate and di-calcium silicate that are compounds found in portland cement.

Jan 1, 2015

By W. M. Weigel

Langley is about nine miles north of Augusta, Georgia., on the Sou them :l;.ilv1ay. According to the South Carolina. Geological Survey, tr.e district is known a.s tr. Horse Creek and Town Creek sub-areas of the Aileen or Savannah River Area f the South Ciil.Z'olina Coastal Plains. The geology and origin of the clays 3l"e Jscribea in a bulletin of the South Carolina Geological Survey (Series 4, Bull, l; "A Preliminary Report on Cl.:.ws of South Carolina.-), According to this report, i.he clays are sedimentary kaolins, in the Mid.dendor! and Hamburg series of the Cretaceous Age.

Aug 1, 1922

By F Pirajno

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. China’s mineral deposits are the result of metallogenic processes associated with the geodynamic evolution of tectonic plates and eventual amalgamation into their modern configuration. The principal tectonic provinces of China comprise the North China Craton, Yangtze Craton, Cathaysia Craton, Tarim block, Altay-Tianshan-Hinggan orogens (part of the Central Asian Orogenic Bel), Central China orogens, Songpan-Ganze orogen and Alpine-Himalayan fold belts, which are part of the huge Tethysides. These tectonic elements are testimony to a complex geological history spanning more than 3000 million years. This contribution will focus on selected areas of the Altay-Tianshan, the fold belts surrounding the North China Craton and Yangtze Craton and the mineral systems along the Ailaoshan-Red River fault zone. Mineral deposits in these provinces include gold, copper, molybdenum, tin, antimony, nickel, platinum group elements, lead and zinc.CITATION:Pirajno, F, 2015. Metallogeny and related tectonic settings in China , in Proceedings PACRIM 2015 Congress, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Turgut Yalcin

"Recent years have seen a resurgence of interest in flotation cell design, and one of the areas where attention is being focused is flotation in centrifugal fields which aims at increasing the flotation rates by forced bubble-particle contact.A new cycloflotation device was developed at Laurentian University and tested on the nickel ore of Falconbridge Limited in Sudbury. In comparison with conventional flotation, cycloflotation yielded at least seven times faster flotation rates in terms of the mass of solids floated per unit time per unit flotation volume, while producing concentrate grades similar to those of conventional flotation. These results, which were obtained with a bench-scale ""cyclofloat cell,"" suggest that cycloflotation has the potential of setting a new direction in flotation technology.IntroductionFroth flotation is no doubt the dominant separation technique in the mineral processing industry. Since its inception early in this century, much research effort has been and is still being expended on this process. Until recent years, emphasis seems to have been placed on the chemical aspects of flotation, but there is now an increased awareness for the need to improve flotation machine performance and more and more attention is being directed towards this area. In a 1982 article on ""Flotation Machines"" (Young 1982) it is stated that "" ... by now the design of the machines used would have reached a high level of perfection, ... In fact, this is not the case ... "".The process of flotation in a flotation device may be considered to take place in several distinct stages as follows:"

Jan 1, 1994

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By D. Bienstock, J. H. Field, M. J. Lempel

A computer program is presented to perform the detailed and numerous calculations required for determining the interface temperatures and steady - state heat flow through a furnace wall composed of several refractories in layers . A method is developed that will allow the designer to determine the various thicknesses for each refractory layer to minimize either the total wall thickness or the cost of the wall per unit of area . A sample problem is presented and analyzed to illustrate the techniques involved .

Jan 1, 1964

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By T. S. Lundy, R. A. Padgett

The fact that cobalt diffuses in silver at a much slower rate in a region near a free surface than in bulk material has been demonstrated in a variety of experiments. Various possible mechanisms of this near-surface effect (NSE) are examined in light of experimental evidences. The tendency for surface segregation of some solute atoms appears to be a likely mechanism to explain the effect. UNIDIRECTIONAL and isothermal diffusion from a plane source of radioactive tracer into an isotropic, homogeneous medium follows the Gaussian solution to Fick's second law, or: where A(x,t) is the position and time-dependent concentration of the diffusing species, M is the quantity of diffusant per unit area initially at x = 0, and D is the diffusion coefficient. For a given time, say t = tl, one can easily see that: d In Aixji)_____1_ r2] d(x2) 4Dti Thus, if diffusion data obtained by serial sectioning are plotted as In A(x,tl) vs x2, the diffusion coefficient is obtained from Eq. [2]. The ideal behavior seldom is observed in real systems. Deviations from ideality generally occur either at small or large values of penetration distance. The overall picture is shown schematically in Fig. 1 where Regions I, 11, and 111 are due, respectively, to some near-surface effect or effects (NSE), volume diffusion, and short-circuiting effects. For different systems and conditions of specimen preparation and analysis, the relative importance of Regions I, 11, and I11 may be drastically different. Region I is completely absent in many systems and there is no NSE. In others, however, there may be considerable difficulty in determination of volume diffusion coefficients due to the overshadowing influences of Region I. Such is particularly true when indirect techniques such as the surface concentration decrease or the Gruzin method' are used to find D. In this paper several experiments which had as their goal a better understanding of near-surface effects are reported. Specifically, it is well-known that unusual penetration behavior results for the diffusion of several impurities in ilver- and that considerable controversy exists with regard to interpretation of the published diffusion data. We chose to examine those unusual results which occur for cobalt diffusion in monocrystalline silver395 primarily because knowledge of experimental procedures and materials were readily available. Both radioactive co60 and co5' could be utilized to offer a wide range of available concentration of the diffusing species. Experiments were also performed on the diffusion of AgnO in silver. They gave base-line data for the system—both for technique evaluation and for examination of the vacancy distribution near the surface. I) PROCEDURES Cylindrical-shaped specimens 1.25 cm diam and 1 to 1.25 cm long were cut from 99.999 pct Ag single crystals obtained from Monocrystals Co., Cleveland. One end surface of each specimen was polished flat and etched with a mixture of 20 ml saturated Cr03 solu-tion-20 ml H20-3 ml concentrated HC1. Radioactive tracer (co60 or co5' or Ag'lO, each having a radio-chemical purity of greater than 99 pct) was deposited onto the prepared surface either dropwise with evaporation to dryness of the solution containing the tracer (0.5 N HC1 solution for the co60 and co5' and 0.6 N HNO3 solution for the A"'), by electroplating, or by evaporation from a tantalum or tungsten filament in an evacuated bell jar. The amount of deposited cobalt was varied from many atomic layers of cobalt containing the co60 to approximately one co5' atom per lo6 surface atoms of silver. This large variation in amount of deposited cobalt yielded information about both the influence of a thick-source layer of tracer and solubility effects on the NSE. Such variations were possible because of the large differences in half-lives,

Jan 1, 1969

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By AIME AIME

A COMMITTEE, representing a number of the larger oil companies in California, met in San Francisco on Nov. 12, 1919, for the purpose of discussing the depletion deductions to be allowed in computing the Federal income taxes under the Internal Revenue Act of 1918. It was the general sense of the committee that a system based on sound engineering principles should be formulated for estimating the value of oil properties, so that better and more uniform results might be obtained by the various companies in filing their returns with the' Bureau of Internal Revenue. A subcommittee, consisting of five petroleum engineers, was thereupon appointed to collect information and draft a report. The committee consisted of G. C. Gester, Carl H. Beal, J. H. G. Wolf, E. G. Gaylord, and E. D. Nolan; this report is the work of that subcommittee.

Jan 1, 1920

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017