Search Documents

By J. E. Wilson

A bench-scale expansion tester using 71 grams of coal was developed to determine the practicability of an apparatus of this size to investigate the effect of variables such as oxidation, blending, bulk density, inerts, size consist, petrographic differences, and rate of heating on the expanding properties of coal. The value of this tester is shown by the correlation that exists between its results and those of the larger scale sole-heated oven expansion apparatus used in commercial plants. From tests on 32 coals the standard error of estimate for predicting sole-oven results from bench-scale results is ± 5.3 percentage points. A standard deviation of the difference between pairs of tests in the latter apparatus of ± 2.1 percentage points was determined for 31 samples. In the sole-heated oven test the expansion of a coal at constant pressure is directly proportional to the dry coal bulk density. Tests in the bench-scale tester show a similar relationship between expansion and bulk density. When the blending ratios of high-and low-volatile coals are varied, similar changes in expansion are observed in both the sole-heated oven and the bench-scale tester. Therefore, the effect of other variables on expansion should be similar in the latter apparatus.

Jan 1, 1960

By Ankit Jha, RICHARD AMOAKO

In this paper, we examine the challenges associated with the use of empirical rock fragmentation models. We highlight key parameters omitted by these models, and propose a machine learning approach that incorporates these parameters, leading to a simple, yet more accurate approach to blast design.

Feb 1, 2020

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By Jay J. Burns

TWO zinc concentrating mills are operated by the St. Joseph Lead Co. in St. Lawrence County, N. Y. The Edwards mill is operating at present only sixteen hours a day treating 400 tons daily. The metallurgy at Edwards presents no unusual problems therefore this discussion is mainly limited to the metallurgy of the Balmat ore. The Balmat mill has a capacity of 1,250 tons per day and the operating crew consists of three shift bosses each with five millmen per shift. Two crusher operators work on each of two shifts and one cleanup man on day shift. The repair crew is made up of a foreman and three repairmen, one of the repairmen being capable of taking over any operating job in the mill from shift boss down. Each millman is capable of handling the next job in line and several men in the yard crew are broken into handling the start-off job in the mill so that temporary shortages of men do not cause extensive overtime. Sphalerite, pyrite, and galena, the principal ore minerals, occur in a gangue of calcite, dolomite, and silicates, especially diopside, plus tremo-

Jan 1, 1947

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978

By L. Avramovic, B. Han, R. Jonovic, Z. Stevanovic, K. Haga, S. Dimitrijevic, A. Shibayama, L. Godirilwe, Y. Takasaki

Pyrite (FeS2) and chalcopyrite (CuFeS2) which could not be recovered, are present in mine tailings discharged from Bor copper mine. About 0.3% of copper (Cu) is contained in these tailings, therefore it can be considered as a useful copper resource. At the same time, pyrite is known to promote acid mine drainage, therefore it is necessary to detoxify the tailings. An efficient method has been proposed to recover copper and reduce the environmental impacts of tailings by a combined hydrometallurgical process of high pressure leaching (HPL), solvent extraction (SX) and electrowinning (EW) process. HPL process yielded high copper leaching rate (>95%) when water (H2O) was used as a leaching media. On the other hand, pyrite contained in the tailings was converted to iron oxide by high pressure leaching. Stability evaluation of the residue obtained from high pressure leaching, confirmed almost no elution of metal ions. The percentage of copper extracted and stripped from the Cu-loaded organic phase reached 97.4%. Moreover, it was confirmed that a low iron concentration in the electrolyte of copper electrowinning, resulted in the improvement of current efficiency of copper electrodeposition. INTRODUCTION Mine tailings are a by-product obtained from the flotation process and there are billions of tons of already existing tailings all over the world. Moreover, several billion tons of additional copper tailings will inevitably be produced in the coming years (Onuaguluchi & Eren, 2012). With the declining average copper ore grade, alternative sources of copper are highly sought, mine tailings have a comparable copper grade to that of low-grade ores (0.2–0.3%) therefore, it can be said that copper mine tailings present a very important source of secondary raw material for copper production (Antonijevi´c et. al., 2008). Consequently, it is necessary to confirm the possibility of the valuable metals (such as copper) recovery from mine tailing in which copper content is about 0.2–0.3%. Our group investigates the flotation and high pressure leaching processes for recovering of copper from mine tailings. Previous work on related samples include copper and nickel flotation tailings from Botswana, and a low–grade copper ore sample from Chile. Impurities, which are associated metals in mine tailing such as iron (Fe) and aluminum (Al) co-dissolve into the solution during the HPL treatment process. Therefore, separation of copper from impurities is necessary for selective extraction of copper from mine tailings and upgrading the copper concentration in the leachate to enable further purifying of Cu by electrowinning. Thus, it is important to investigate the possibility of applying solvent extraction for concentration of copper from leachate solutions of mine tailings (Onuaguluchi & Eren, 2012; Antonijevi´c et. al., 2008). In this study, LIX-84I was used as an extractant of copper from the leachate of high pressure leaching of mine tailing. As a fundamental solvent extraction investigation, the extraction behavior of copper was studied using a simulated solution of the leachate from the high-pressure oxidative leaching of mine tailing. The effects of; solution pH, extraction time, extractant concentration and phase ratio on copper extraction and sulfuric acid (H2SO4) concentration on stripping were investigated.

Jan 1, 2019

By William C. Cooley

[ ]

Jan 1, 1975

By E. Pizarro, A. Videla, G. Compan

One of the main problems related to mining investment decisions is the use of accurate prediction models. Metallurgical recovery is a major source of variability, and in this regard, the Chuquicamata processing plant recovery was modelled as a function of geomining-metallurgical data and ore characteristics obtained from a historical database. In particular, the dataset gathered contains information related to feed grades, ore hardness, particle size, mineralogy, pH, and flotation reagents. A systemic approach was applied to fit a multivariate regression model representing the copper recovery in the plant. The systemic approach consists of an initial projection of the characteristic grinding product size (P80), based upon energy consumption at the particle size reduction step, followed by a flotation recovery model. The model allows for an improvement in the investment decision process by predicting performance and risk. The final geometallurgical model uses eight operational variables and is a significant improvement over conventional prediction models. A validation was performed using a recent data-set, and this showed a high correlation coefficient with a low mean absolute error, which reveals that the geometallurgical model is able to predict, with acceptable accuracy, the actual copper recovery in the plant.

Jan 1, 2015

By Margaret E. Egan

Reliable fire detection is essential for both safe evacuation and containment or extinguishment. In order to increase reliability by reducing the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Experiments were conducted by the Bureau to compare the smoke detection capabilities of the DDD with those of conventional fire detectors in response to smoldering coal and conveyor belting. A comparison was made among the alarm times of a carbon monoxide (CO) detector with an alarm threshold of 5 ppm, a smoke detector with an optical density alarm threshold of 0.044 of', and the DDD with an alarm threshold of 0.025 V. The results show that the DDD will reliably detect developing coal and conveyor belt fires. The average time delay separating the DDD alarm from the first detector to alarm was 76 s for smoldering conveyor belt and 65 s for smoldering coal. The longest time delay between the response of the DDD and the first detector to alarm was approximately 120 s.

Jan 1, 1993

By Charles B. Carpenter

When a drilling well strikes a horizon in which there is a large volume of petroleum or natural gas under high pressure, danger of a blowout with disastrous results is imminent unless proper precautionary measures are taken. The history of oil-swell drilling has been marked by many blow-outs and wild wells, some of which-have caught fire and burned for long periods. Such incidents nearly always make headline news, but ordinarily few persons realize that what to them is an interesting newspaper item may entail great financial loss to the operator and frequently loss of life or personal injury to members of the drilling crew and others in the vicinity of the well. The blow-out, wild well, and crater are dreaded specters to every thoughtful person in the oil industry because of danger to life and property, underground damage to surrounding wells, dissipation of reservoir energy, and waste of irreplaceable natural resources that blow to the air or migrate to barren formations. Every operator drilling in high-pressure fields must be on the alert always to forestall any conditions that may lead to a blow-out, and his vigilance must not cease until a well is completed and oil, gas, or both are flowing to storage or market.

Jan 1, 1937

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By D. W. Carson, R. J. Trembley

Thoron daughter WL&apos;s measured by alpha-spectroscopy and the Kusnetz method are about one-half those of radon daughter WL&apos;s in a uranium mine in Canada.1 A diffusion model can account for the relative concentrations.l Since the Kusnetz technique is most widely used for measuring radon daughter WL&apos;s in uranium mines, a general procedure is derived to extend this method to measurement of WL&apos;s of radon and thoron daughters in air containing their mixtures. Coté P. and Townsend M.G., 1981. A procedure is also suggested for counting radon and thoron daughters by 3-channel [a]-spectroscopy. Errors in WL(Rn) are calculated for standard radon daughter counting procedures when a-decay of both thoron and radon daughters is attributed to radon daughters alone. Providing overall counting times are short, [<]30 min, these errors are generally small. The precision of ß -counting methods is also investigated. A portable 3-channel alpha spectrometer for measurement of radon and thoron daughters in uranium mines or homes is described, Carson D.W., 1979. The computer programs for analyzing the data to give, depending on the mode employed, some or all of the concentrations RaA, RaB, RaC, ThB, ThC and WL of radon and thoron daughters by alpha spectrometric, modified Kusnetz, Rolle and Tsivolglov methods are presented.(l) A commercial apparatus, based on the above prototype, incorporating a microprocessor and built under contract to EMR is now available.(2) A number of personal radiation dosimeters for miners are now being tested in mines. One of these is the CEA dosimeter which uses the track-etch film method, Duport P., Chapuis A.M. and Pradel J., 1979. An apparatus for rapid reading of track-etch films by the spark technique has been described previously, Cross W.G. and Thomasino L., 1970 and Huang V.F., 1975. We have developed such an apparatus for rapid semi-automatic reading of films exposed to radiation from mixtures of radon and thoron daughters in CEA dosimeters. The films used, Kodak LR 115 Type II Strippable, may be stripped rapidly and easily, for counting after irradiation and developing, by use of a special punch and suction technique. The method promises to provide an inexpensive and rapid technique for reading large quantities of personal dosimeter films. However, the present CEA dosimeter has faults in design, leading to a contamination problem. Those films that show contamination cannot be read by automatic means. A commercial apparatus based on the above prototype spark counter and built under contract to EMR is now available.3 1. These computer programs are available on request. 2. Pylon Instruments, Ottawa 3. Bondar Clegg, Co. Ltd., Ottawa. REFERENCES Carson, D.W., 1979, "Canalph-3, a Portable Three-Channel Alpha-Spectrometer for Measuring the Daughter Products of Radon and Thoron", CANMET Division Report MRP/MSL 79-108 (TR). Coté, P. and Townsend, M.G., 1981, "Mixtures of Radon and Thoron Daughters in Underground Atmospheres", Health Physics, Vol. 40, pp 5-16. Cross, W.G. and Thomasino, L., 1970, "Rapid Reading Technique for Nuclear Particles Damage Tracks in Thin Foils", Radiation Effects, Vol. 15, pp 85-89. Duport, P., Chapuis, A.M. and Pradel, J., 1979, "Appareil Individuel pour lu Dosimetrie des Descendants du Radon", Advances in Radiation Protection Monitoring, IAEA Vienna, pp 435-443. Huang, Y.F., 1975, "Determination of Uranium in Minerals using Fission Tracks", M. Sc. Thesis, University of Toronto, 48 pp.

Jan 1, 1981

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By Thomas A. Giordano

Portable communications equipment is becoming increasingly important in underground mining. Proper selection of microphones and hearing devices to be part of these communication systems is essential if the messages are to be transmitted intelligibly. In this program a thorough study of the requirements for these transducers was made with respect to intelligibility, mechanical configuration, human factors and safety. A computer analysis was made to predict how several combinations of transducers would perform at typical mining noise levels. A survey has been made of those microphones and hearing devices on the market today that might be applicable to the miner communication system. Several systems are proposed and evaluated.

Jan 1, 1976

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By John W. Graham

To start my talk, I thought it might be helpful for us to define the term "aggregate", so I went to the dictionary. Webster has several listings under "aggregate", and I found the following: "1. A mass or body of units or parts somewhat loosely associated with one another." Well, I didn&apos;t like that term "loosely" so I read on. "2. Crystals of one or more kinds of mineral or rock fragments." That sounded better, but I still read on. "3. Any of several hard inert materials used for mixing with a cementing material to form concrete or mortar." That sounded even better, but it should be a little broader. So I would like to define "aggregates" for you as follows: "Hard, inert fragments of rock or minerals used alone or with cementing agents to form products essential to nearly all types of construction." Usually aggregates are sand, gravel, or crushed stone, but other minerals such as clay or shale can be heated and become aggregates. What are some of the construction uses? Well, we&apos;ve already mentioned concrete, as used in streets and highways, sidewalks and parking lots, airports and all kinds of building construction, not to mention bridges and swimming pools, and docks and breakwaters, just to list some of the uses. Our way of life couldn&apos;t exist without concrete. And you can&apos;t have concrete without aggregates,

Jan 1, 1977

By C. J. Chindgren

Upgrading of commercial red cake and recovery of vanadium oxide from uranium-vanadium mill solutions were investigated by the Bureau of Mines. Alternative procedures potentially useful for manufacture of high-quality vanadium oxide at the mill site were explored and developed. The simplest and best procedure for converting commercial red cake containing about 10 percent combined sodium and potassium oxides (Na20) (K20) into a 98- to 99-percent vanadium pentoxide (V205 product appeared to be a metathesis in an ammoniacal solution of ammonium sulfate. Molybdenum, as well as the alkali metal oxides, was removed from the red cake by this procedure at a modest expenditure of labor and reagents. When preparing vanadium oxide of higher grade, it was necessary to dissolve the red cake and reprecipitate the vanadium as ammonium metavanadate. Calcination at 450° C, decomposed the metavanadate and yielded oxide of about 99.5 percent V205. By recyrstallizing the metavanadate before decomposition, an oxide product approaching 99.9-percent purity was obtained.

Jan 1, 1962

By J. Olsson

Introduction Stainless steel has by tradition been a common construction material for hydrometallurgy processes and the most common grades can be found amongst the ASTM 300-series, i.e. austenitic grades of type 304L, 316L and 317L. However, there are a number of new grades available today, which imply more cost effective solutions for those designing plants where good resistance to acids, containing the desired metal ions, often contaminated with chlorides and other halides, is the key issue. There are austenitic-ferritic or duplex grades having the same or even better corrosion resistance than the austenitic grades and approximately twice the strength, which enables design in thinner gauges, which in turn implies less weight and less cost. They have also excellent engineering properties, enabling fabrication of process equipment, machinery and different types of tanks. On top of that, they contain less nickel and molybdenum than their austenitic counterparts, which implies not only lower cost for alloying elements, but also a more stable price when considering the price fluctuations for these alloying elements during the last years. This paper describes briefly the family of duplex stainless steel and it presents a number of relevant corrosion tests where duplex grades have been compared with austenitic grades. The results have in several cases been verified by in-plant exposures in zinc and copper production plants. It also describes applications and experience of duplex grades within a variety of hydrometallurgy plants. Installations of highly alloyed austenitic grades will be described as well. The corrosion tests and service experience reported cover hydrometallurgical processes based on sulphuric acid.

Jan 1, 2007

By Feng Wang, Guojing Shi, Yangyang Xie, Zizong Zhu, Qiang Wu

The coal chars from northwestern part of China are characterized with high reactivity and low strength after reaction. Four type of coke-making coals selected from northwestern part of China were studied by proximate analysis, ultimate analysis, vitrinite reflectance analysis, and FTIR with curve-fitting analysis to obtain information on their chemical composition and chemical structure. The results show that the studied coals have relatively high values of final contraction of coke residue index (x) and relatively low values of maximum thickness of plastic layer (y) and average vitrinite reflectance. Based on the curve-fitting analysis of FTIR spectra, the aliphatic carbon (Cal), the aromatic carbon (Car), and the molecular structural parameters such as CH2/CH3, fa, Hal/Har, and (R/C)u are determined. The results of curve-fitting analysis indicate that the studied coals are characterized by a large amount of oxygen-containing functional groups and aliphatic side chains.

Mar 1, 2018