Search Documents

By V. A. Preto

The Rexspar uranium deposit is located approximately 5 kilometres south of Birch Island, B.C. Three separate zones of commercial-grade uranium mineralization mineable by open pit have been outlined. Uranium and fluorite-celestite mineralization occur in a trachytic member of alkali-feldspar porphyry, lithic tuff, tuff breccias and pyritic schist conformably interlayered with a succession of strongly deformed greenschists and fragmental rocks that are, in large part at least, of volcanic origin. The age of these strata is not precisely known, but they are considered as part of the possibly Mississippian Eagle Bay Formation. Commercial-grade uranium mineralization is always associated with fluorphlogopite-pyrite replacement of the trachytic unit and is contiguous to, but separate from , a zone of ore-grade fluorite mineralization. In all zones, ore occurs in lenses of variable thickness and lateral extent, which lie parallel to the schistosity of the trachytic rocks and surrounding greenschists. The principal radioactive minerals at Rexspar have been identified by other workers as uraninite, uranothorite, bastnaesite, torbernite and metatorbernite. Considerable amounts of thorium oxide and widespread rare earths have been reported from all three radioactive zones. The geology of the deposit suggests that the trachytic rocks represent a highly differentiated intrusive-extrusive system in which fluorphlogopite, pyrite, fluorite and uranium-bearing minerals were deposited late in the evolution of the system by deuteric, volatile-rich fluids. The considerable amounts of thorium and widespread rare earths associated with the uranium tend to support the thesis that this element is of primary origin rather than secondary.

Jan 1, 1978

By James E. Norman

[The flotation of mica is mentioned frequently in the literature, but must of the references have dealt with the recovery of mica by the old anionic collectors. The first use of the new cationic reagents indicated their superiority- as collectors in the flotation and a. agglomerate tabling of micas, feldspars, quartz, clay, and other acidic mineral, but the separation n of these minerals from each other necessitated study of the flotation of each mineral.]

Jan 1, 1941

By Keithe J. Merl, Brendan FitzPatrick, Gregg Piazza

Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges while also balancing the practicality of implementing solutions within site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations. This paper highlights two projects for an international shipping company where mezzanine level additions within active shipping facilities required construction of new foundations. Construction requirements included low vibration levels, as well as rapid and clean installation to limit impacts on the active shipping operations. The selected system also needed to adjust to both variable ground conditions and differing overhead clearances. This paper describes the installation, design and performance of Ductile Iron Piles used to meet the project challenges. The low vibration, driven pile system offered the ability to work within restricted overhead environments while successfully delivering working compression capacities ranging from 45 to 75 tons (41 to 68 tonnes) as well as lateral and tension resistance. The paper also presents the results of site-specific load testing (and pile capacity) for various termination criteria. INTRODUCTION Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges associated with the new construction. Foundation solutions must also balance the need to achieve design requirements with the practicality to be installed within the particular site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations.

Jan 1, 2019

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By John R. Marks

The first 0.7 m3 (1 cu yd) diesel load- haul-dump vehicle (LHD) arrived at the Homestake Gold Mine in Lead, SD in I969 to muck a ventilation drift. Others soon followed. Mechanization has subsequently changed stoping methods, manpower requirements, ventilation practice, the definition of minable reserves, and it has impacted safety and health. These have all had a direct bearing on the economics of producing gold ore from deep underground. Mechanized mining Before mechanization, production quotas at Homestake were met by several open cut-and-fill (OCF) mining methods. OCF mining relied on jackleg and wagon drilling, electric and compressed air slushing and cribbed raises brought up through the fill. Even square- set stoping was used until about eight years ago. The mine became 100% mechanized in 1988. The two current stoping methods are mechanized cut-and-fill (MCF) and vertical crater retreat (VCR). In 1992, MCF accounted for 54’S, VCR for 44% and development/uphole for 2% of the 1.4 Mt (1.55 million st) of underground ore produced. These methods are typically ramp- based and use diesel-powered LHDs, trucks, pneumatic drill jumbos and utility vehicles. Electric LHDs and rubber-tired compressed air muckers have also been used in VCR scrams. Pfarr (1991) and Mitchell (1980) provide good overviews of current production methods.

Jan 1, 1993

By J. R. Jutras, C. Brissette, J. Champagne

"Pure cadmium sulphide was leached by the action of the bacterium Thiobacillus thiooxidans in the presence of finely divided sulphur. The influence of time, temperature, pH and concentration of inoculum on the extent of the cadmium extraction was studied. Under optimum conditions, up to 72 per cent of the cadmium could be dissolved over a six-week period. A cursory study of the role played by elemental sulphur seems to indicate that its presence is essential but that the sul1>huric acid produced through its oxidation is a minor factor in the cadmium extraction."

Jan 1, 1971

By Stephen C. Tadolini

The Bureau of Mines conducted field investigations in two underground mines to determine the actual loads to which bearing plates were subjected when installed in conjunction with full-column resin-grouted bolts and the roof movements generated by the applied loads. Measured loads indicate that the bearing plate is an integral part of the support system. Vertical displacement gauges installed to monitor roof displacements in the test sites show that the highest degrees of loading occur in conjunction with the largest amounts of movement.

Jan 1, 1986

By G. M. Potter, S. J. Hussey, R. Havens

The Artillery Peak manganese ores , from one of the largest known manganese deposits in the United States , present a difficult problem in concentration because they are low-grade and the association of manganese and gangue minerals is intimate and complex. The known size of this deposit has justified investigation of processes such as leaching, wherein preliminary enrichment of the original feed might be advantageous .. Therefore , the ore-dressing studies on Artillery Peak ores were carried on with the object not only of making directly marketable manganese products but also of removing acid-consuming calcite and raising the grade of ore for leachingplant feed . Owing to the extent of the deposits , test work was carried on at the Salt Lake laboratories in considerable detail on several lots of ore of varying composition . This paper summarizes the results obtained from laboratory testing of four samples obtained by engineers of the Mining Branch from the Maggie Canyon area of the Artillery Peak deposit . Also included are results obtained from testing one sample of Chapin Group ore , which was considered representative of numerous very low-grade ores submitted from the Artillery Peak district . During the course of the investigations , many data were obtained and compiled , but for the sake of brevity , data of secondary importance have been omitted or condensed and only those tests giving the more pertinent results are discussed in detail ...

Nov 1, 1947

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982

By P. Rosario

The application of high pressure grinding rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits supporting this trend are better energy efficiency, improved grinding capacity, and higher metal recovery in downstream processes such as heap leaching and flotation. In general there is limited quantitative knowledge on the true benefits of HPGRs relative to SAG mills in comminution, and about which situations one deals with better than the other. This paper will present a structure for comparison of the energy requirements for HPGR versus SAG mill considering complete circuits for comminution of precious and base metals hard ores. The work presented is from the design of four complete circuits based on ore data from two sites.

Jan 1, 2010

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By Rafael César de Souza

A distribuição de gás de Aciaria, gerado no processo de produção de aço, tem como finalidade que a energia térmica recuperada seja utilizada nos seguintes processos da TKCSA: - Aquecimento dos regeneradores dos Altos Fornos e Planta de PCI através do fornecimento de um Mix Gas composto de gás de Alto Forno, gás de Aciaria e gás natural; - Fornecimento de gás combustível associado ao gás de Alto Forno para as turbinas a gás da Termoelétrica, para que a energia térmica seja convertida em energia mecânica e finalmente em energia elétrica; - Fornecimento de gás combustível para o forno de ignição da Sinterização e os fornos de aquecimento de panelas da Aciaria. - Fornecimento de gás combustível associado ao gás natural para uma caldeira que tem como finalidade a produção de vapor de processo. Sendo um processo extremamente importante dentro do sistema de distribuição de Utilidades e termos como diretriz a redução de custos operacionais e obtenção de benefícios ambientais, foram desenvolvidas várias ações para aumentar a capacidade de distribuição do gás de Aciaria, sendo que tais ações proporcionaram um incremento de 20% na capacidade de distribuição do gás de Aciaria.

Aug 17, 2017

By Jared Ball, Darren Snashall, Paul Telford, Pengfu Tan, Ben Hogg

"The foamed converter charges were up to 3 8 per month in Xstrata Copper Smelter at Mount Isa. The issue of high converter foamover frequency had remained unsolved for many decades in Mount Isa. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow, in order to understand the mechanism of converter foamover. The model predicts the chemistry and viscosity of slag during slag blow and copper blow. The effects of oxygen potential, charge of dirty reverts, slag carryover, under-blowing, over-blowing, and temperature on the foamover and viscosity of slag in copper blow have been discussed. A theory has been developed to understand the mechanism of converter foamover. The practical solutions have also been developed and implemented in Mount Isa Copper Smelter. Some improvements of the industrial operations have been presented. After a series of improvements, the number of foamed charges per month in the converter operations has been decreased significantly from 35 in Aug 2008 to only one per month in 2009/2010.1. IntroductionThe Copper Smelter in Mount Isa receives the concentrate containing about 25% copper and produces anode copper that contains about 99% copper. There are several stages in the process. The first stage carries out in the ISASMELT™ furnace. The ISASMELT™ process produces a molten copper matte containing about 60% copper. An iron-silica slag and a sulfur dioxidebearing off-gas are the by-products of the process. The slag is taken to the slag dams for cooling before it is recycled through the Mount Isa Copper Concentrator.The matte is sent to Peirce-Smith converters. The converters further remove iron and sulphur to produce blister copper which contains about 97% copper. The anode furnaces remove any remaining sulphur and oxygen to produce anode copper that is about 99. 7% pure. This is cast into anodes and sent to the Xstrata Copper Refinery in Townsville for final refining.In the copper pyrometallurgical industrials, slag foaming is an important phenomena which occurs when the gas bubbles have stability and not rupture. Foaming greatly increases the interfacial area between matte, slag and gas and is essential for the operation of high intensity smelting processes. However, foaming or foamover is undesirable in P-S converter since it can damage the equipment and injure the operators. Figure 1 shows that the whole process of a foamover development in a converter."

Jan 1, 2011

By J Penman, N Turner, H Liu

This paper aims to present a snapshot of the risk profile for tailings storage facilities within Western Australia by comparing the spatial distribution of known facilities against common geohazards such as cyclonic activity, climate, and peak ground accelerations from earthquakes. The analysis also includes an assessment of proximity to populations at risk including towns and sensitive receptors including significant river systems and wetlands.

Jul 1, 2021

By R. E. Brewer

Published investigations show that many different chemical reagents have been used in determining the constitution of coals , but only a few studies have been applied directly in evaluating the effects of such reagents on the carbonization products of coal , Most of the treatments have been so drastic that any permissible conclusions that may be drawn are inferential in respect to any favorable effects on the yields and composition of the usual carbonization products .

Sep 1, 1943

By M P. Sandy, R M. Stephenson

Portals to access underground mines are important infrastructure and their design requires careful consideration. Portals are generally expected to last for the life of the mine. Typically, the exposure of personnel and equipment is high, with many hundreds of movements through the portal per day. Consequently, the risk associated with geotechnical instability must be extremely low. Portals are often established from a boxcut. In areas where the weathering profile is well developed, the design and execution of the boxcut can involve significant effort, with the objective of minimizing the volume of the boxcut, whilst ensuring that conditions at the design depth are suitable for establishing a stable portal. Properly designed site investigations are a critical part of this process. Currently available portal design guidelines have not been updated for decades, however the equipment and ground support systems have changed significantly in recent years. Many mine portals have since been constructed in a relatively short time frame with success, often in challenging ground conditions using some of the more modern approaches to ground support. This is beneficial because delays in establishing a portal will generally delay other critical path activities, and lead to cost overruns.

Mar 15, 2021

By L. M. Southwick

"The history of extractive metallurgy is replete with examples of commercializing new processing technologies. The successes are widely reported, but failures seldom are. This is unfortunate, for usually we can learn more specifics on how to succeed in technology development by studying and thoroughly understanding their failures. Frequently one encounters a red herring that caused the whole effort to fail. A thorough and objective due diligence up front would have identified those red herrings and prevented the pursuit of a bad idea and the resulting destruction of capital. Due diligent analyzes performed before construction of three such bad ideas will be discussed. One is an EAF dust process, which pursued the red herrings of a poor understanding of the business, a naïve view of past experience, and false confidence in the technology. Another will examine the effort to commercialize a new pressure copper leach process that followed the red herrings of inadequate testing of the raw material, application of processing conditions that were inherently unsafe, and an improper assessment of the inherent advantages of past developments. The last is an alternative iron-making process, where the red herrings were incomplete and superficial assessment of prior pilot plant and demonstration plant tests, an assumption that the commercialization model of “build it and we will make it run” was viable, and a technology whose technical fatal flaws had already been identified. Unfortunately, capital destruction often also closes the window to more intelligent pursuit of technology development. TECHNOLOGY COMMERCIALIZATIONThe development and commercialization of new technology is a vital part of keeping industry profitable, able to deal with new sorts of feed stocks and current with economic, product, operational and environmental requirements. This is a difficult task in the best of times, and can be compounded when the developers become enamored of a particularly favorable characteristic of the project or of the product. These “red herrings” divert project focus away from the arduous path to success and, in the end, result in project failure."

Jan 1, 2012

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By Joseph Javes Aramburú

El presente texto describe la optimización del circuito de molienda y clasificación de la planta de hierro, el cual comprende un molino de barras y de bolas. El proceso se inicia con la exploración geológica, se determinan las reservas probadas y probables, y se establece la forma de explotarloLa eficiencia de la molienda está en función del volumen útil del molino a diferentes volúmenes de llenado que permite determinar los parámetros óptimos de la operación.

Apr 1, 2013