Search Documents

By T. Tanaka, H. Kiuchi

The combination of the following two exothermic reactions was studied with the purpose of recovering H2 from H2S formed in acid leaching of sulfide ores, direct reduction of metal sulfides with H2 or desulfurization of crude oils: In the kinetic study of the recovery of H2, the reaction rate was measured by the two methods of single-stage and circulation blowing of H2S through molten Pb in the temperature range of 550 to 750°C. The experimental results showed that the rate determining step is in the chemical reaction itself and also that this reaction is accelerated markedly by the addition of a trace of Ni, which may be responsible for the catalytic action of Ni dissolved in molten Pb. In the experiments where Pb metal was produced, PbS was oxidized in a stream of atmospheric N2 containing 0.5 to 20 vol-% 02 or in the same 02 partial pressures as in N2 though under reduced pressures in the temperature range of 400 to 800°C. It was found from these experiments that the formation of PbSO4, basic sulfates and PbO are suppressable to yield Pb metal alone above 750°C and for 02 concentrations of less than 1 vol-%. Vapor of PbS was thought to take an important part in the Pb formation mechanism, and the probability thereof was demonstrated thermodynamically.

Jan 1, 1978

By G. Kolosay, J. Rajala, G. Deschênes, A. Romanov

ABSTRACT: The Kupol project, located in Far East Russia, treats a high-grade, free-milling ore containing 25.5 g/t Au, 298.3 g/t Ag, and 0.5% pyrite,with a P70of 53 microns. Most of the gold occurs as elec-trum and the silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite, andproustite. The mill reached the design throughput of 3,000 tpd six months after start-up. AKnelson con-centratorrecovers10.4% gold and 0.5% silver. Leaching (14.5 hours pre-treatment and 116 hours cyanidation)of gravity tailings is performed with the CANMET Enhanced Leach Process (CELP),using only 490 ppm NaCN (cyanide consumption of 1.1 kg/t). The precious metals are recovered by counter-current decantation and the Merrill-Crowe process. Calcium hypochlorite destroyscyanide and thiocyanate. Overall, gold and silver recoveries for 2008 were 95.4% and 85.6%,respectively (2.8% and7.5% higher than targets). In the first eight months of 2009, gold and silver recoveries were 95.0% and82.6%, respectively. By August 2009, the mill processed 1.42 million tons of ore with production of 1.1 million ounces of gold and 11.3 million ounces of silver. CELP performance was not affected by changes in feed grade and ore mineralogy. Additional modifications to the leaching strategy allowed further reduction in cyanide consumption and effluent treatment costs.

Jan 1, 2011

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

By R. Blickensderfer

Maintaining an adequate supply of minerals and metals to meet national economic and strategic needs is the overall goal of the Bureau of Mines, U.S. Department of the Interior. One method of achieving this goal is to conserve scarce metals by cladding a plentiful base metal, such as iron, with a scarcer metal. To investigate cladding, a vacuum-rolling mill capable of rolling bimetal specimens at temperatures to 1,300° C in a residual gas pressure of 2 x 10-5 torr was established. Metals that were successfully bonded to iron included stainless steels, chromium, nickel, nickel alloys, copper, and several refractory metals including molybdenum and titanium. The effects of the rolling temperature, reduction in thickness, rolling speed, and residual air pressure on bonding strength and bend ductility of the bimetals were determined. Optimum rolling conditions produced bimetals with bond shear strength essentially equal to that of the iron base metal.

Jan 1, 1980

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By Alan D. Hartman

Standard metering of electric arc furnaces usually uses root mean square (RMS) or true root mean square (TRMS) measurements for determining power. Only sinusoidal signals are accurately described by RMS meters, and dc or high-frequency components normally are lost in standard TRMS metering. This can lead to inaccuracies when electrical signals are not sinusoidal, contain dc components, or include fast risetime perturbations, as is the case with the electric signals from an electric arc furnace. Electric arc furnace electrical waveforms, observed in research carried out by the U.S. Bureau of Mines, show high-frequency components and significant deviations from sinusoids. These perturbations and distortions make metering difficult for standard power meters. The inaccuracies in metering can cause further problems if those sensors are used in control systems. For control strategies requiring rapid response, any averaging scheme loses information that can be used in control decisions. In order to obtain better signals for both monitoring and control, a study of instantaneous, RMS, and TRMS power monitoring devices was conducted. From this study it was concluded that precision integrated circuits should be used to obtain instantaneous power with a bandwidth of at least 25 kHz. The information from these devices is more representative than that of standard meters and can be used in predictive control.

Jan 1, 2010

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By H. J. Lechtenberg

Preliminary results are given of solvent stimulation of two wells producing viscous oil (14°-17° API) from the Tar zone in the Wilmington field, California. The solvent (coker oil, an intermediate refinery product) was injected into the formation, and after a soak period, the well was returned to production. Data are given on crude oil properties, solvent properties, determination of volume of solvent in the produced oil, rate of oil production before and after stimulation, volume of additional oil produced, and volume of solvent recovered. Although further study and improvement of the method arcs needed, cyclic solvent stimulation appears to be an unqualified success in one well and a moderate success in the other.

Jan 1, 1972

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By The Staff

BEFORE going into detail on the subject to be presented, a brief outline of the Company's earl y history would not be out of place. Prospecting and mining on a small scale was started in 1876 on the site of the present open pit at Thetford Mines. The property was purchased from the Crown in 1878 and Johnson's Company was incorporated in 1885. It is owned and operated today by descendants of the original shareholders. Many employees, through their fathers and grandfathers, have service records dating back three generations. The principal asbestos deposit at Thetford Mines is pear-shaped, with surface dimensions of about 2,200 feet in length by 1,300 feet in maximum . width. Its long axis strikes northeast and the dip is nearly vertical, but irregular in detail. It is known to extend to a depth 1,200 feet below the original surface, but its area at that depth has not been determined. Ownership of this deposit is divided among three active Companies: the Asbestos Corporation, Limited; Bell Asbestos Mines, Limited; and John-son's Company. Johnson's Company owns a section about 1,000 feet in length and 500 feet in width, bounded on the northeast by the King mine of the Asbestos Corporation and on the northwest by the Bell pit. On Johnson ground, there was originally a large outcrop o~ asbestos rock which dipped toward the south below overburden. This was mined until recently by open pit, the overburden being stripped off as far southward from the original outcrop as was economically possible. As the. pit was deepened, within side walls maintained at a maximum safe slope, its floor area, of course, became progressively smaller, and eventually the pit would have wedged out against the Bell property line. It became necessary, there-fore, to introduce some other method of mining before production became seriously curtailed by a shrinkage of the pit area.

Jan 1, 1941

Coal mining legislation makes frequent reference to æSafety Management SystemsÆ but there is a chronic shortage of useful guidance material as to how these might be applied to hazardous exposures. Several studies have indicated that for each death that is reported as a result of an industrial æaccidentÆ, there are five deaths that caused by occupational exposures. Because the deaths from occupational exposures do not occur on site and often well after employment has ceased, they are generally unreported. Improved access to mortality data from coroners, the Australian Institute of Health and Welfare and superannuation service providers (early claims from death and total permanent disability), has given rise to some analysis of death and disability data that provides evidence that there are emerging opportunities to develop and improve safety management systems for hazardous occupational exposures. Issues explored include how safety management systems might be developed in relation to dusts and chemicals and other hazardous exposures to ensure the risk of disorders with long latency periods are reliably assessed and the exposures effectively managed. The current standards and guidelines which refer to safety management systems in general or to management of exposure related hazards are examined. Many standards are based on dose-response studies that provide for an acceptable percentage of workers to suffer adverse health outcomes. An alternative management system might be to apply dose-response relations to health surveillance to identify æat riskÆ individuals and effectively manage health and related safety risk at an early stage.

Jan 1, 2005

By A. Noble

"Linear circuit analysis (LCA) is a fundamental tool that may be used to evaluate, design and improve the performance of mineral separation. The traditional LCA methodology provides a comparative evaluation of circuit designs purely from the unit interconnections. The quantitative approach uses the analytical circuit solution to evaluate the slope of the circuit’s partition curve at the midpoint. Since the partition slope is often associated with a separation’s general selectivity, this numeric value is used to compare and rank alternative configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. By itself, this value does not account for the relatively high unit dollar value of pure material or the gains and losses in mass yield associated with alternative circuit configurations. Realizing the value in the LCA methodology, but respecting the limitations of the partition slope valuation, the authors have derived two new performance indicators that quantitatively address pure particle misplacement (the Partition Moment of Inertia) and circuit mass yield (the Yield Score). Together, these parameters provide a better indication of separation economics in typical mineral and coal separation systems. Since the two parameters provide independent information on circuit selectivity and circuit yield, a Pareto efficiency, multi-objective function selection approach is proposed for preliminary circuit selection.IntroductionOver the past 30 years, numerous scientific and industrial studies have proposed various mineral processing circuit design methodologies that attempt to optimize the allocation of separation resources within the processing plant. Over this period, the methodologies have undergone various transitions, including the increased inclusion of process models and computationally intensive algorithms, as well as a general shift from a purely technical solution (Lauder and McKee, 1986) to partially economic solutions (Abu-Ali and Sabour, 2003; Cisternas et al., 2014). Today, circuit design is largely driven by flowsheet simulation; however, no consistent design methodology is used across the industry.One intriguing approach for circuit evaluation is linear circuit analysis (Meloy, 1983a). This method evaluates the separation potential of the circuit solely considering the unit configuration and stream interconnections. No preliminary data other than the basic circuit configuration is required to use the approach."

Jan 1, 2015

By F. T. Havard

(Canal Zone meeting, November, 1910.) I. INTRODUCTION. THE present truce in litigation between Western smelting and ranching interests gives opportunity for a summary of the results achieved by metallurgists in condensing fume and de-acidifying furnace-gases. In the absence of complete records of past experiments, there has been a good deal of unnecessary duplication of attempts and' failures. Yet, especially under the recent policy of our large corporations, looking to the economic recovery of the values of by- and waste products, original and, in some cases, effective measures have been developed by American metallurgists. In the case of Bliss vs. the Anaconda Copper Mining Co., the Montana Supreme Court, recognizing the progressive efforts made to render the flue-gases innocuous, and the value to the community of the smelting company's operations, refused to hamper its work, and returned a verdict in favor of the defendant. In the trial, the experimental firms of the company in the so-called "affected region" were proved to be thriving perfectly, showing that immunity was guaranteed to vegetation and stock by the wide distribution of the sulphurous acid gas in the dry air of Montana. Indeed, L. S. Austin has proved that by the time the fume is 4,000 ft.. distant from the stack, the percentage of sulphurous acid has been diminished from 2.28 to 0.00045; and Angus Smith has shown that rain must contain 40 parts per million of free acid before vegetation is affected. The arsenic in the stack-gases is but a very small part of the original content of the ore, of which 80 per cent. and over is rejected in the concentrator and furnace waste-products or recovered in the flues. Nevertheless, neither the peace in Montana nor the armistice

Aug 1, 1910

THE object that the writer has mainly in view in presenting this paper is to draw the attention of those connected with the technical side of the industry to the unsatisfactory and by no means up-to-date methods employed in estimating the tin contents of an ore. At the same time, what is regarded, from the writer's personal experience, as a satisfactory and reliable method is explained in detail. It is a curious fact that for the last 25 years tin·assay methods have made little or no advance, while those now in general use ill connection with copper and lead ores can scarcely be compared with those then obtaining, so greatly have they been improved upon. Though it. is not altogether expected that the method herein advocated will at once meet with general approval, the writer hopes the resultant discussion may bring out points that have hitherto escaped detection.FIRE METHODSThe old Cornish method of smelting with anthracite is now obsolete. The cyanide assay, although unreliable, is still much used because of its simplicity. In the Malaya many buyers of tin ores use the cyanide assay, the smelting being carried out generally in a benzine furnace. It is essential that the smelting with cyanide be performed at a low temperature. Even then, impurities, such as Sb2S3 and...

Jan 1, 1912

By Richard T. Newcomb

Federal and utility industry research has largely ignored coal beneficiation techniques in the implementation of SOx control. This paper accepts the hypothesis that beneficiation cum scrubbing is the cheapest way for the vast majority of seams in the eastern coal provinces to comply with standards. Comparisons are based on point estimates of average beneficiation costs from a model of coal preparation (COBET) designed to simulate four levels of cleaning. The paper describes how economic theory can be applied to derive econometric supply functions from actual data on the geology of minable seams, washability and technical constraints. West Virginia is taken as an example of a producing region. Spatial supply functions are derived empirically from the engineering model simulations.

Jan 1, 1977

By L. S. Jen

Canadian copper, nickel, zinc, lead and molybdenum mines are characterized by the mining of ores from which more than one metal is recovered. During the 1980s, approximately 15% of the gold, 25% of the zinc, 30% of the copper, 55% of the molybdenum, 80% of the silver and 90% of the lead produced from Canadian mines were produced as co-products and by-products of base metal mining operations. This trend is not expected to change significantly in the near future. The presence of co-products and by-products affects the level of production and the level of revenue from base metal mines in several ways: (I) in general, production of one base metal cannot be expanded or cut back without affecting the amount of production of another metal;(2) the commercial success of certain base metal mining operations depends on the substantial bonus revenues from co-products and by-products; (3) the quality and economic viability of many ore deposits are significantly improved by the presence of co-products and by-products; and (4) while coproduction is critical to the survival of some mines, bonus revenue from by-products can also be life saving to others during economic downturns. For these reasons, deposits with significant co-product or by-product values are likely to continue to be significant targets for exploration and for acquisition.

Jan 1, 1992

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

By J. Chupak, D. J. Salley, G. L. Simard

Radiotracers were demonstrated to be of considerable value in a study of the interaction of dithiophosphate with galena. The interaction had characteristics of both chemisorption and chemical reaction, being complex because of the nature of the galena surface. Sorption was rapid and markedly reversible, and flotation occurred at relatively small amounts of dithiophosphate sorbed.

Jan 1, 1950

By M. R. Geer

Coal washing assumed an important role in the mining industry of the Pacific Northwest long before washing practice became firmly established in the Appalachian field. A Scaife washer was operated in the state of Washington in 1887; and by 1927, the fist year for which complete statistics were compiled, nearly a third of the state's coal production was washed, in comparison with only about 5 pct for the country as a whole. Mechanical preparation was adopted in Alaska in 1922 in a plant constructed by the United States Navy at Chickaloon to provide bunker coal for naval forces operating in northern waters. Many of the coal beds mined in Washington and Alaska contained more impurities than those mined elsewhere, and this circumstance contributed to the early interest in mechanical cleaning. A much more important factor, however, was the inclination of the coal beds. With steeply pitching beds, hand sorting by the miner at the face is impossible; consequently, all material must be loaded and dealt with on the surface, just as is now proving the case with mechanical mining of flat beds. Thus "full-seam" mining afforded the same stimulus to the early development of coal washing in the Northwest that - it is providing under mechanization in the rest of the country today.

Jan 1, 1949