Search Documents

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By M. Y. Zhou

The paper elaborates on the significance of producing ultra-low-moisture ore concentrate, the operating principle and technical features of thermocompression- filtration process, the kinetics involved in the dewatering process, and the technological process system and equipment used. It is pointed out that it is possible to reduce the moisture of fine ore concentrate to a minimum. By way of example, the case of the treatment of flotation molybdenum (Mo) using the thermocompression- filtration process is cited.

Jan 1, 2014

Discussion of the paper of ALBERT SAUVEUR, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2439 to 2449 G. K. BURGESS, Washington, D. C.-This very instructive contribution by Professor Sauveur to our knowledge of that puzzling substance, Hadfield's manganese steel, should not only be read in connection with the paper of Messrs. Hopkinson and Hadfield referred to by Professor Sauveur (Bulletin No. 87, pp. 513 to 530, March, 1914); but one should also have in mind, as throwing much additional light upon the questions raised, two papers recently presented before the Iron and Steel Institute, the one by Sir Robert Hadfield (Journal of the Iron and Steel Institute No. II, 1913) on Heating and Cooling Curves of Manganese Steel, the other by Messrs. Hadfield and Hopkinson (ibid., No. I, 1914) treating of the Magnetic and Mechanical Properties of Manganese Steel. We then have brought together for this substance, the thermal, magnetic, and mechanical properties as well as the resulting microstructure, for the definite heat treatments described, and in particular after long annealing between 500° and 700° C. Sir Robert Hadfield and Professor Hopkinson see in the properties found for manganese steel (of C = 1.25 and Mn = 12.5 per cent.) a demonstration of the untenableness of the allotropic theory of iron, whereas Professor Sauveur reaches the contrary conclusion, that some of the facts observed can be explained only in terms of the existence of beta iron in steel of this composition. There is another possible hypothesis: namely, that these several series of experiments shed no light on the subject of the allotropy of iron, or at least as regards the existence of beta iron. However heretical it may sound, I am inclined to this last belief.

Jan 4, 1915

By J. A. Woolf, E. S. Leaver, N. K. Karchmer

"In the cyanidation of silver ore, the need of oxygen is well recognized. Various methods have been introduced for supplying the oxygen. In usual practice, air is the source of oxygen and the methods of application are mechanical.This article gives the results of touts made to show the rate of dissolution of silver from each of the common silver minerals in cyanide solution, under conditions similar to those used in the practical recovery of silver from its ores. The effect of oxygen in aiding the dissolution of the silver from each mineral is also shown by a comparison of the methods of supplying the oxygen. Oxidation by preliminary roasting (500°C.) of each mineral sample gives the maximum extraction of the silver by treatment with cyanide.Each silver mineral5 used in these experiments was as pure as could be obtained from the mineral dealer. In their natural occurrence, silver minerals are not usually free from mineral impurities. They are usually closely associated with other minerals often forming, a complex mixture. The form of crystallization, the proportions, and properties of the diluent that incases or has been dispersed with the silver mineral may decidedly affect the dissolution rate of the silver from each mineral. While the following results should aid in the cyanidation of silver ores, each ore should be studied from the basis of the form and condition of the silver that is to be recovered.All the tests reported in this article were made on synthetic samples, prepared by mixing the particular silver mineral with clean sea sand. Each mineral was ground in an agate mortar to pass 100-mesh before mixing with the sand which had previously been ground in a porcelain pebble mill to 100-mesh. Such proportions of each mineral and the sand were used as to give a head assay of approximately 20 ounces of silver per ton to the synthetic sample.Agitation was carried on in stoppered bottles approximately one-third full of pulp, method apparently supplied all the atmospheric oxygen that would be taken up by the solution under usual conditions, because tests conducted in open bottles did not show increased recovery,"

Jan 1, 1931

By NA NA

A round up of recent industry matters. Davis Derby acquisition of Safecom UEP Ltd. Record Output by Longannet Mine.

Jan 7, 1997

By W. W. Adams

The quantity of explosives sold in the United States in January, 1931, for domestic consumption, amounted to 368,100 kegs (9,202,500 pounds) of black blasting powder, 4,610;000 pounds of permissible explosives, and 16,533,000 pounds of high explosives 'other than permissible. These figures are based on reports received by the United States Bureau of Mines, Department of Commerce, from nearly all manufacturing companies, and include an estimate of sales by several companies that do not furnish monthly reports. Reports actually received from manufacturers showed soles of 365,977 kegs of black blasting powder (consisting of 220,892 kegs of granular powder and 145,085 kegs of pellet powder), 4,687,900 pounds of permissible explosives, and 15,496,152 pounds of high explosives other than permissible. Sales in January, 1931, were smaller than in January, last year, the decreases being 14 per cent for black blasting powder, 19 per cent for permissibles, and 17 percent for high explosives other than permissible. Sales in January 1931 when compared with soles in December 1930, show increases for all three classes of explosives as follows: 2 per cent for black blasting powder, 16 per cent for permissible explosives, and 7 per cent for other high explosives.

Jan 1, 1931

By Erik Melchiorre, M. Katherine Crombie, Dante Lauretta, Chris Gholson

Rich Hill, also known as Weaver District No. 2, is among the most productive placer gold locations in Arizona. Located near Congress, AZ (Fig. 1), this district hosted major placer rushes in the 1860s and1930s. Those rushes were followed by an electronic metal detecting rush that started in the 1980s and continues today. Thousands of ounces of gold have been produced by these modern amateur and professional metal detectorists. Many of them see more gold in an afternoon than Nevada mine workers will ever see outside of the mill. Rich Hill discovery Inspired northeastward by Spanish legends, a party of 10 men left Yuma, AZ on April 1, 1863. Included in the group were Pauline Weaver (Fig. 2), Henry Wickenburg and Abraham Peeples. Wickenburg left the group near the Hassayampa River and discovered the Vulture deposit. The rest of the group arrived at the base of Rich Hill in late May. While drying antelope meat on the first day, a few of the men prospected a nearby creek bed and immediately found gold. In a couple of hours they picked up more than 2.8 kg (90 oz) of gold. The next day, four members of the party went searching for their horses and returned with news that a nearby hilltop was literally graveled with nuggets.

Jan 1, 2003

This paper discusses the impacts that advances in metallurgy and process engineering have on minerals project execution. Ausenco's business is focused on integrating minerals processing technology and the delivery of cost effective processing plants that exceed client performance expectations. The metallurgical development is a small but critical part of this process. Metallurgical development and innovation outcomes need to be transformed into an engineered solution and that solution converted into an operating plant in a cost conscious and competitive environment. Including new or innovative processes in a project flow sheet increases a project's technical and commercial risk. However, it also gives the project, and/or the engineering company, a potential advantage over projects using mainline practices. Managing the balance between risk and opportunity has been a cornerstone of Ausenco's success in recent years. Some advances in "technology" that are discussed in the paper include: larger capacity equipment new flow sheet concepts simplification of process interfaces, and more effective project strategies The common theme is that having a new idea can be the easy bit, putting it into operation effectively involves numerous people, many interfaces and strong project management.

Sep 13, 2010

By B. S. Xakalashe, I. J. Geldenhuys, M. W. Erwee, Q. G. Reynolds, R. T. Jones, S. P. Tsebe

Aspects of the production of platinum group metals by reductive smelting in direct-current arc furnace processes are investigated using a computational modelling approach. The replacement of fossil carbon as a reductant by alternative reductants such as silicon carbide, ferrosilicon, and hydrogen is desirable for reducing direct greenhouse gas emissions from such processes, but the impact of these changes on the electrical operability of the process is poorly understood. This paper presents a study of plasma arc behaviour in the context of the ConRoast® reductive smelting process for Upper Group 2 ore as well as processes for recycling of automotive catalysts, using an integrated computational modelling workflow. It was found that the freeboard gas compositions, plasma properties, and arc behaviour were all affected by the choice of reductant, particularly in carbon-free smelting using ferrosilicon or hydrogen.

Mar 6, 2026

By Leandro Rocha Lemos, Guilherme Liziero Ruggio da Silva, Iara Patricia Vieira de Oliveira, Paulo Santos Assis, Lorena Cristina Amorim Moura

O coque fica exposto a diferentes solicitações mecânicas do tipo impacto, abrasão e compressão, desde o desenfornamento até o seu consumo no Alto-Forno. Para evitar que o coque sofra uma acentuada degradação, é exigido que o mesmo apresente uma elevada resistência mecânica a frio. Para monitorar tal parâmetro, utiliza-se principalmente o teste de tambor, porém este contempla apenas a degradação por impacto e abrasão. Neste contexto, este trabalho desenvolveu uma metodologia para avaliar a resistência mecânica à compressão, inicialmente em partículas individuais de coque, apontando quais seriam as granulometrias mais resistentes. Os coques foram transformados em corpos de provas e testados em máquina de ensaio universal. Os resultados apontam que a tensão média de ruptura cresce com o aumento da granulometria. Posteriormente, foi avaliado a resistência mecânica à compressão em leito de coque, onde foi possível simular em uma prensa hidráulica, a pressão que a coluna das cargas exerce sobre o leito de coque no Alto-Forno e, posteriormente, correlacionou a compressão com o teste de tambor e se obteve excelentes resultados.

Oct 1, 2019

By Daniel Antonio Kapper Fabricio

O módulo de tenacidade é um parâmetro que representa a energia absorvida por um material até a ruptura, e é uma variável importante para avaliar se o material sofrerá fratura quando em serviço. A tenacidade é determinada através da área sob a curva tensão-deformação de engenharia, a qual é difícil de ser calculada analiticamente. Assim, o presente trabalho propõe a utilização de métodos numéricos para o cálculo do módulo de tenacidade através de planilhas eletrônicas. Como resultados são apresentados o procedimento desenvolvido e os valores obtidos na estimativa da tenacidade de uma amostra, assim como a comparação do resultado com o valor calculado analiticamente e com o valor calculado através de um método simplificado. Conclui-se que o valor numérico calculado é tão próximo do verdadeiro quanto maior o número de pontos obtidos na curva tensão-deformação de engenharia, viabilizando a utilização desse método na estimativa da tenacidade de uma ampla gama de materiais. Além disso, o método numérico pode ser usado na determinação de outras propriedades calculadas através da área sob curvas.

Aug 7, 2018

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By N. R. Zehr

El presente texto describe los problemas de desague y ventilación que corresponden al túnel Graton en Casapalca. En ese sentido, Antonio Raimondi menciona que probablemente fue Gratón, el primer túnel de desagüe en Casapalca: «la veta de San Antonio es drenada mediante túnel socavado hace poco tiempo y recientemente terminado. Esta conecta con áreas de trabajo situadas por debajo de las ya inundadas de modo que, para efectuar el desagüe, solo tendrá qµe perforarse en plano inclinado. Los túneles Graton tendrán poco más de 11 km, los cuales pueden perforarse desde accesos en el Valle del Río Rimac, poco más arriba del pueblo de San Mateo, en un punto denominado "Carbonyacúpalabra" quichua que significa «agua de carbón». Asimismo, estos túneles gemelos se terminarán bajo el pozo de la mina Aguas Calientes de Casapalca. Una vez terminado, una perforación servirá para desaguar las áreas de trabajo y la otra, para la respectiva ventilación.

Jan 1, 1969

By E. W. Dewing

The solubility of A14C3 in cryolite melts has been determined by holding the melt with aluminum in a graphite crucible for 4 hr at temperature, quenching the crucible in water, and analyzing the frozen salt by CH4 evolution. The solubility is given by log(wt % Al4C3) = 1.298 -1.l74 (wt ratio NaF/AlF3) independent of temperature in the range 985" to 1080°C. Additions ofA1203, .NaCl, CaF2, or LiF up to 10 wt pct do not affect the solubility, provided that LiF and CaF2 are replaced by equivalent NaFin calculating the ratio. The variation with ratio can be accounted for quantitatively on the hypothesis that the Mechanism of solution is Al4C3 + 2AIF3 = 3Al2CF2 since the solubility varies as (aAIF3) 2/3; Mechanisms involving C", C2- , AlC- , A12C2+, and Al2CF+are re-jected. At ratios above 1.5 truces of c;- are also present. It was noticed some years ago in this laboratory that carbon specimens made cathodic in a cryolite bath decrease in diameter over a period of time.' It was also found that cryolite which had been melted with aluminum in a graphite crucible was sometimes yellow, and that A14C3 could be seen intimately embedded in the cryolite crystals. CH, could be recovered by acid attack. There was thus reason to believe that A14C3 had a genuine solubility in molten cryolite, and the object of this work was to measure it. EXPERIMENTAL AND RESULTS A graphite crucible, 2 in. ID and 2.5 in. deep with a close-fitting lid, contained about 150 g of cryolite (plus additives) and about 20 g of 99.99 pct pure Al. It was placed in a vertical Inconel furnace tube, covered with refractory brick to provide thermal insulation, and the top of the tube was roughly sealed with disks of asbestos paper. An alumina tube led argon down to the level of the top of the crucible to expel air, and an alumina sheath with a Pt-10 pct Rh ther-mocouple inside was positioned between the crucible and the wall of the Inconel tube. The tube was heated in an electrical resistance furnace for the desired length of time; the refractory bricks were then removed, and the crucible was lifted out with tongs and quenched in water. After such a crucible was broken open it could be seen that its inner surface was yellow owing to the presence of A1,C3, and sometimes needle-like crystals could be observed (at X75 magnification) growing out into the nielt. It was concluded that Al,C, had been present as a separate phase when the crucible was at tenlperature and that the melt had been saturated: in

Jan 1, 1970

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By R. Padilla, M. C. Ruiz, L. Salinas

Chloridizing roasting of bismuthinite (Bi2S3) with NaCl–O2 has been studied to remove the impurity Bi by volatilization from copper concentrates that contain bismuthinite. The study was conducted using mixtures of Bi2S3 and NaCl in a horizontal furnace and TGA apparatus. The variables were temperature, oxygen partial pressure, and NaCl concentration. The chlorination was analyzed by weight loss measurement method. XRD results of calcines reacted for short times in 21% O2, and 850–1000 °C showed the presence of Bi, BiOCl, and Na2SO4, while at longer times in the same conditions, Bi2O3 was identified as a stable phase. Thus, the chloridizing-volatilization of Bi2S3 proceeds through the formation of Bi and BiOCl. Temperature affected significantly the fraction of weight loss of samples. At 600 and 900 °C in 10.3% oxygen, the maximum weight loss was 4 and 20%, respectively. An increment in the partial pressure of oxygen in the range 1–21% affected negatively the Bi2S3 conversion. At normal roasting temperatures (550–700 °C), bismuth volatilization by NaCl roasting was found to be marginal.

Mar 1, 2017

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period June 10 to July 10: J. C. Ralston, Spokane, Wash. E. P. Ashmore, So. Porcupine, Ont., Can. William H. Yeandle, Jr., Mexico City, Stuart Croasdale, Denver, Colo. Mexico. W. E. Hopper, Houghton, Mich. W. C. Minsch, Mexico City, Mexico. D. W. Brunton, Denver, Colo. H. V. Winchell, Minneapolis, Minn. Fred Crabtree, Pittsburg, Pa. W. G. Swart, Denver, Colo. Robert S. Lewis, Salt Lake City, Utah. D. F. Schindler, Madison, Wis. Noel Cunningham, Timmins, Ont., Can E. R. Pettebone has just been elected a Trustee of the Pennsylvania State College, being supported by the votes of the delegates of the Pennsylvania Anthracite Local Section of the Institute and the Engineers' Society of Northeastern Pennsylvania.

Jan 8, 1914

By Wemerson Junio Gandra

Para a redução do minério de ferro no alto-forno é necessária a utilização de uma fonte de carbono, que pode ser encontrada no carvão mineral e/ou carvão vegetal. Diante do cenário atual, a busca constante por maior competitividade, associada ao atendimento da qualidade e aos requisitos ambientais, exige a implementação de várias ações alternativas no processo de fabricação de gusa. Dentre elas, destaca-se a utilização de combustíveis alternativos no sistema de injeção dos altos-fornos, como por exemplo, a substituição parcial do carvão mineral pelo carvão vegetal. Do ponto de vista ambiental, é altamente favorável a utilização de uma fonte renovável de carbono. O objetivo desse trabalho é apresentar a adequação do processo, desde o recebimento do material até sua injeção nos altos-fornos, bem como os resultados já alcançados e os desafios futuros. A utilização do carvão vegetal na mistura de carvão pulverizado resulta em flexibilidade na utilização de matérias primas e contribui para preservação do meio ambiente.

Oct 30, 2017

By Gary Almeraris, Vincent Jr Tirolo

Traditionally, “Means and Methods” were the sole responsibility of Contractors. However, because of a number of litigious projects in the 1970s, Owners and their Engineers began including Suggested Methods of Construction (SMC) in Contract Drawings. By the late 1990s these SMCs were becoming baseline “Means and Methods” with Contractor recommended changes often considered as Value Engineering proposals. By 2004, the word “Suggested” was sometimes changed to “Prescriptive.” Owners are also purchasing TBMs and other mining equipment for Contractors prior to bid. Is limiting the contracting community’s innovation in developing their own “Means and Methods” and selecting their own equipment in the best interests of the Owner? Does it reduce the Owner’s, Engineer’s or the Contractor’s risk? Are claims reduced and finally what is the impact on the bid? A questionnaire was sent to more than fifty senior engineering field and management personnel representing more than 30 heavy construction companies to ask their opinion on these questions.

Jan 1, 2005

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939