Search Documents

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By Hongjie Yang

The No. 10 metro line of Shanghai city is 36 kilometers in length and will pass through the operating airport runway by using tunnel boring machine with earth pres-sure balance mode. Although there are examples through world that tunnels pass through airport runway and tunnelling underground is not a difficult undertaking technically, there is rare experience in China for the similar projects especially in Shanghai saturated soft soil region. Shanghai soft earth is famous for its high compressibility, high rate of water content, weakness in strength, large deformation and different characteristics in earth strata. Besides, the whole construction process will be under ultra-large airplane dynamic load on the surface ground over the tunnel, which increases the risks of construction process. This paper evaluates the feasibility of building the metro tunnel under such an extremely serious condition, especially the subsidence of ground surface caused by advancing of tunnel boring machine, which also is the most important control target for the safe operating of the runway. Furthermore, this paper discusses the effective measures to keep the settlements in the permissible level during the whole working period for the tunnel from aspects of plan, design and construction.

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

Longwall mining originated in the early 18th century in the county of Shropshire in England, where it was known as the longway method. Its name implies the extraction of the seam over a long continuous length or wall of exposed coal. Until the late 19608 and early 1970s the use of the longwall system with a few exceptions was confined to the United Kingdom and Europe. It was not until the early 19708 that the highly productive longwall faces we now know, were developed and the application of the longwall system extended to Australia, South Africa, United states of America and other parts of the world. The modern longwall face has three major components, namely: +         the machine to break and load the coal +         the face conveyor; +         and a system of roof support.   This paper reviews the development of longwall mining technology. The parameters directly influencing the production 'of a modern longwall face are considered, as are the possible constraints to the further development of the longwall system.

Jan 1, 1991

By Mike Lovitt

New Gold Inc. had commissioned Orica to assist with the design of the drawbell blasting at New Afton Underground copper/gold block cave at Kamloops, British Columbia, Canada. Orica have had much success in developing the single-shot drawbell method at Freeport Indonesia in 2001 in the Deep Ore Zone and they will be using it exclusively in their new Grasberg Underground Operation. RioTinto Northparkes have also used the single shot drawbell blasting in their Second Lift E26 Project and even in the E48 orebody which is a post undercut block cave, realising the safety and operational benefits of this blasting method.

Jan 1, 2013

By Frederico Muylaert Margem, Jarbas Bravo Neto, Sergio Neves Monteiro

"The mechanical behavior and the fracture characteristics of composites with DGEBA/TETA epoxy matrix reinforced with up to 40% in volume of continuous and thinner ramie fibers were evaluated by tensile tests. Specimens with selected thin fibers aligned along the tensile axis were room temperature tested to rupture. The fracture surface was analyzed by scanning electron microscopy. The results showed significant increase in both the ultimate tensile strength and the elastic modulus. The fracture analysis indicated the possible mechanism for the fiber/matrix interaction, which could be responsible for the composite performance.IntroductionThe fiber reinforced polymer composite emerged in the middle of last century as a versatile engineering material for applications requiring mechanical resistance in association with lightness. Its most commonly used example is ""fiberglass'', i.e., a thermoset polymer matrix composite reinforced with glass fiber. Indeed, ""fiberglass"" has a specific strength of the order of 500 MPa.cm3/g, which is the double of the strongest steels like the maraging. This motivated, at earlier times, ""fiberglass"" to replace many conventional materials including wood and natural fiber composites. Today, ""fiberglass"" has a wide range of uses from aerospace systems and appliances to sport and leisure components. However, its fabrication as well as those of any synthetic fiber such as carbon and aramid composites, requires a relatively large amount of energy. Presently, a growing concern exists regarding the consequences to the environmental by gases like C02 associated with both the energy consumption and the processing of synthetic fibers and their composites. These gases are well known responsible for global warming [1]."

Jan 1, 2011

By I M. Platten, S C. Dominy

The Clogau St DavidÆs gold mine has a recorded production of around 81 000 oz Au and it is the largest mine in the Dolgellau gold-belt and BritainÆs most prolific historical producer. The original mine was first worked for copper, however; in 1854, gold was found in waste material from the St DavidÆs section. In recent times the mine has operated intermittently between 1983 - 2007. The principal black shale-hosted gold-bearing reef (Main Reef) can be traced for about 3 km, striking approximately NE-SW and dipping steeply between 60¦ - 90¦ SE. The reef system pinches and swells, changes strike and splits into a number of smaller branches. Reef width is variable, ranging from over 6 m to a few cm and in places reducing to small irregular blobs. The reef is internally complex and composed of swarms of narrow (1 - 300 mm) subparallel veins separated by country rock sheets. The gold-bearing veins within the reef package are discontinuous; though generally possess bonanza grades running 10s - 100s oz/t Au. It has historically been shown that some gold-rich vein segments can grade up to 300 oz/t Au. The predictability of the gold-rich segments is poor, but has been shown to be related to presence of the Clogau (black shale) Formation, and/or the mechanical interactions of the reef with greenstone sills, reef branching and splitting and/or cross-fractures to form ore shoots. The mine is currently being re-evaluated as a potential small-scale selective operation.CITATION:Dominy, S C and Platten, I M, 2012. Geology, mineralisation and potential of the Clogau St DavidÆs mine, Dolgellau gold-belt, Gwynedd, Wales, in Proceedings Narrow Vein Mining 2012 , pp 101-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

ecent work on decoppering lead is reviewed; CuS is formed rapidly even from dilute solutions of copper in lead. he mechanism of decoppering is discussed, and an explanation for the retention of metals such as silver in lead is dvanced. As decoppering tin appears to be an analogous process, the Cu-Sn-S system is studied at 300¦C. CuS, hich is not, an equilibrium product, is found in decoppering drosses. In the removal of nickel from lead, Ni3pb2S2 formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by tirring in sulphur. Decoppering bismuth is thermodynamically favoured, but is complicated by the occurrence of uBiS2. The Cu-Pb-S system is the only one of the four studied where the equilibrium can be calculated simply, as ' resence of ternary sulphide or other phases invalidates calculations based on binary data.

Jan 1, 1970

By Y. C. Kim

One-quarter of a century has passed since the "theory of regionalized variables" (geostatistics) was introduced by G. Matheron (1962, 1963) in France. Yet, only during the past decade has geostatistics found broad acceptance in the mining industry. Foremost among the reasons for this time lag was ignorance. The first English treatise on geostatistics was not written until Matheron (1971), and the first published text accessible to mining professionals did not appear until David (1977). Other significant reasons for the slow acceptance of geostatistics included the conservative nature of management in the 1970s minerals industry, and the fact that conventional ore reserve estimation performs reasonably well when confined to massive deposits of base metal and iron deposits having relatively low coefficients of variation in grades. In short, mine engineers and geologists were not willing to accept a new set of tools for problems that they did not see.

Jan 1, 1989

By F. F. Aplan

INTRODUCTION The production of coal is a major part of the mining industry. In recent years the production of clean coal has exceeded 600 million tons per year and is reported to have reached 660 million tons in 1977. Some data on the magnitude and utilization for the year 1975 is given in Table I. In that year 648 million tons of soft coal were produced and of this 267 million tons or 41% approximately was produced by mechanical cleaning. Of the 374 million tons of raw coal sent to the preparation plant, 28.6% or 107 million tons was discarded as refuse. In the same year approximately 6 million tons of anthracite were produced and nearly all of this was cleaned. Table I also gives coal utilization statistics for 1975. Excluding the approximately 20% that goes to the coke ovens or to export, the vast bulk of our production is used for steam power generation and a lesser amount for captive production of industrial power and process steam. While much of the nation's coal (e.g. strip mined western, sub-bituminous coal) may be removed from the ground in relatively pure form by modest selective mining techniques, other coal requires preparation in order to remove ash and sulfur constituents and produce an acceptable steam or coking coal. Preparation is often a valuable adjunct to mining in that rather non-selective, low cost, bulk mining techniques may be used underground while the preparation plant is used to reject refuse at low cost above ground. The principal reason for the use of coal preparation is to convert raw coal into an acceptable commercial product by removing the high ash and high sulfur refuse material.

Jan 1, 1979

By Sidney M. Cohen

[Portland cement is a product made from a combination of limestone and argillaceous material which would supply the necessary amounts f calcium, silica, alumina and iron to form cementious compounds when fired at high temperatures. The resulting mixture, usually around 80% limestone and 20% argillaceous, is ground nine (80% -200 mesh), blended and then fired1 (2600-2700°F) to produce a cement clinker from which the final cement product is produced by grinding. The argillaceous component can be shale, clay, slate or other sources of the individual components of silica, alumina and iron. This paper deals with a case where a clay component was under consideration. The planned Plant site was to be located at a well defined limestone deposit. When it came to the argillaceous component, the nearest uniform deposit of clay was over 50 miles away and would require purchase of land or clay from the owner plus the daily delivery costs to the plant site. This situation made the plant site economically questionable. It was decided that a local clay deposit, which was available at the plant site but was orginally not considered due to lack of chemical uniformity and its high free silica content, would be reconsidered.]

Jan 1, 1983

By L. H. Adami, E. G. King

The heats of formation of four sulfides --MnS ( alabandite ) , FeS ( hexagonal pyrrhotite ) , ZnS ( wurtzite ) , and CdS ( greenockite ) -- were determined by hydrochloric acid solution calorimetry . The heats of formation from the metals and rhombic sulfur at 298.15 ° K are , respectively , -51.01 ± 0.19 , -23.81 ± 0.24 , -45.86 ± 0.20 , and -35.70 ± 0.30 kcal /mole . The corresponding free energies of formation were calculated from the heats of formation and the pertinent entropy values .

Jan 1, 1964

By Albert L. Toenges, Theodore R. Jolley

"INTRODUCTION The construction of frame houses (fig. 1) in recent years instead of the conventional sod hut (igloo) (fig. 2) by the Eskimos in the villages along the Arctic Ocean has increased the demand for fuel in these villages. The frame houses, which are not insulated against extreme cold and are difficult to heat, are equipped with Goal stoves. The well-insulated sod huts were heated comfortably with whale-oil stoves. In some years whaling is Door, consequently there is a demand for solid fuel.The Eskimo villages usually are on the sand spits at the mouths of rivers and points of land near the best fishing and hunting grounds. These narrow necks of land usually are sand bars that are not underlain with coal, and coal must be transported to the villages. Lack of development of coal deposits in the Arctic has made it necessary to import coal from the States, generally from 'Washington, to supply these villages. This coal is imported by boat and is received once a year. Its cost is, high, and development of coal deposits in the Arctic to supply these native villages should result in a considerable saving to the Government-operated schools and hospitals as well as to the natives.Early traders attempted to establish coaling stations in the Arctic, and the Eskimos generally know where the coal deposits are situated. A. reconnaissance of a number of deposits in the Arctic was made in the summer of 1946 by engineers of the Coal Division, Fuels and Explosives Branch, Bureau of Mines, and this report describes the areas investigated and suggests plans for the development of some of these deposits."

Dec 1, 1947

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By J. A. Innes

"""The oxygen, next uniting with the carbon, sent up an ever-increasing stream of sparks and a voluminous white flame. Then followed a succession of mild explosions, throwing molten slags and splashes of metal high up into the air, the apparatus becoming a veritable volcano in a state of active eruption.""IntroductionHenry Bessemer F.R.S(An autobiography, 1905)Thank you Mr Chairman for the opportunity to speak: at this, the opening session of your International Symposium on the subject of ""Injection in Pyrometallurgy"". Judging from the list of papers to be presented over the next three days, the Symposium promises to provide a most valuable addition to our existing knowledge base in what is now an extremely active area of R&D investigations. Whilst we have obviously come a long way since Sir Henry Bessemer's pioneering experiments of the mid-19th century, there is still much for us to learn.Most importantly, the Symposium offers a further opportunity to acknowledge the many significant technical contributions made in this field by the Organising Committee's special guest, Professor Howard Worner - one of this country's most respected research leaders.When first approached to give this talk I had two areas of concern. Firstly, I was not entirely clear just what injection metallurgy was meant to cover. How should the overall scope of this particular subject be defined?My second concern related to Howard Worner himself - a man for whom I have the highest personal regard and who, in fact, played a most influential role in respect of shaping my own career. Having already spoken about Howard's achievements on earlier occasions, I wondered what I could sensibly add.Notwithstanding these personal reservations, I am delighted to be here with you this morning. If my thoughts on the meaning and scope of injection metallurgy appear to be slightly off-course, and if Howard should perhaps recognise some repetition in my remarks, then I hope I can be forgiven."

Jan 1, 1996

Contribution by F.S.A. de Frey The authors are to be congratulated on a job well done by making, in their paper, such a pool of information available to mining engineers. I would like to comment on the following statement: 'As an alternative to the commonly used deep-level mining methods, consideration should also be given to pillar mining at great depths as a logical extension of the current methods. For example, a 75 per cent extraction Or Ryder's discussion The moderate levels if average pillar stress (APS) (320 MPa) are consistent with pillar stability. Squat 10:1 pillars should never 'fail' in themselves, and foundation strengths are also not exceeded (the stresses are well below the 2 ½ x UCS rule-of-thumb provided the foundations comprise normal strong 200 MPa quartzites). Authors' reply We thank Dr de Frey for his contribution to our paper on shallow hard-rock pillar systems. To considerable extent, we share his enthusiasm the potential role of squat pillars in deep-level mining, although we harbour reservations concerning strata control, mining economics, other issues. We agree wholeheartedly that further research, together with carefully planned field trials, is warranted in pursuit of this potentially highly rewarding concept. .

Jan 1, 1995

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Arthur V. Corry

GOLD was discovered in Alder Gulch, Virginia. City, Mont., on May 26, 1863. In a short time some 6000 people flocked to the new discovery, and on the banks of Alder Gulch six settlements sprang into existence, the principal one, Virginia City, alone surviving. This town today has a population of 800, and is the county seat of Madison County. It is estimated that between forty and fifty million dollars in gold was produced up to 1904. Virginia City is situated at the mouth of Alder Creek where that stream leaves the narrow canyon that cuts the steep foothills flanking Old Baldy Mountain, elevation 9572 ft., 12 mi. south. Virginia City itself is 5700 ft. above sea level.

Jan 1, 1936

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952