Search Documents

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By F. Roelofse, D. Grobler, and M. Purchase, C. Gauert, E. Kotze

Scandium is an important industrial metal for which demand is projected to increase in the future. Although many Sc deposits are secondary, Sc is scavenged by clinopyroxene during fractional crystallization of primary, mafic-ultramafic magmas. Sc may thus occur in sub-economic concentrations in mafic-ultramafic intrusions. In this work, we present new data on the concentration of Sc in the Bushveld Complex (BC) of South Africa. The eastern and western limbs of the BC are considered to be largely pristine, primary magmatic deposits, whereas the northern limb shows evidence of largescale, localized crustal contamination. Samples from the primary magmatic cumulates of the eastern limb, from the mineralized Flatreef of the northern limb, and from the crustal-contaminated Footwall Assimilation Zone (FAZ) of the Flatreef were analysed for Sc. Despite the FAZ containing abundant clinopyroxene, interpreted to have recrystallized from the original cumulates in the presence of melted sedimentary rocks, no significant differences are seen in the concentration of Sc compared to other cumulate rocks of the BC containing less-abundant clinopyroxene. The concentration of Sc in the analysed samples is mainly controlled by mineralogy, with anorthosites, chromitites, and harzburgites containing under 20 ppm, and norites and pyroxenites containing 20–40 ppm. The parapyroxenites of the FAZ are less enriched in Sc than expected, suggesting that Sc may have been lost during alteration and recrystallization.

Sep 1, 2022

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By B. Grinbaum

The solvent extraction of Cu from acidic leach solutions is carried out using oxime extractants. The mechanism can be described as liquid ion exchange, where a labile H+ in the oxime replaces Cu++ ion from the pregnant leach solution. The process is reversible and, at high acidity, the copper is stripped back to the aqueous phase. As the extraction proceeds, the acidity of the aqueous phase increases and the equilibrium may shift against the extraction reaction. This phenomenon may become significant in leach solutions with high copper concentration, where large amounts of acid are transferred from the solvent into the aqueous phase. An efficient way to increase the recovery of copper consists of splitting the extraction into two circuits, and either neutralizing with lime or extracting the excess acid of the intermediate raffinate. In the second case, the acid can extracted using a solvent, which can be stripped with a base, e.g., NaOH or ammonia. A third option is direct neutralization with soluble basic salt, e.g., Na2CO3, within a single extraction battery. The choice of the preferred process depends on the specific process demands and on the relative availability and price of the raw materials and by-products price.

Jan 1, 2007

By L. Byszynski

The results of a three month evaluation of the application of EMEW® technology at the KGHM Glogów II Smelter tank house bleed stream are presented. The current, conven¬tional electrolyte decopperization process has some limitations, including: only a fraction of its production is commercial grade cathode copper, significant operating costs, low current efficiency, low current densities resulting in low copper depletion rate, and arsine gas and sulphuric acid emission. The EMEW® cell technology developed by Electrometals Technologies Ltd. can overcome many of these limitations. Tests were performed on a pilot EMEW® installation comprising 30 cells at ambient temperature on electrolyte bleed, using current densities between 100 and 600 A/m2 , with copper concentrations between 45 and <1g/dm3. Results showed that a high grade copper can be obtained to the level of 7 g/dm3 of copper concentration in electrolyte. The use of EMEW® technology allows the direct and efficient recovery of over 85% of the copper contained in the bleed electrolyte. Glue & thiourea addition were tested in order to improve the parameters of the copper depletion process. The behavior of Arsenic and Bismuth was observed and a means for their elimination from the system proposed. On-line copper concentration monitoring is proposed to improve control and performance.

Jan 1, 2007

By A Garvie, D Kentwell, J Chapman

"Most new mining projects require an initial assessment of the locations and volumes of potential acid forming (PAF) waste that is likely to be moved and dumped in surface waste stockpiles. This requires sampling of the waste rock zones and submitting the samples for a series of tests. Key to the outcome of the waste characterisation process is obtaining sufficient samples that are representative of the various rock types both in number and spatial distribution.Various regulatory bodies throughout Australia and the rest of the world are currently struggling with how to define minimum amounts of sampling to achieve realistic estimates without imposing excessive costs and time constraints on a project.This paper addresses two aspects of the process: what constitutes a æsufficientÆ number of samples how to use those samples in determining volumes of likely PAF material.Geostatistical methods of characterising orebodies with large numbers of samples are routinely used in the mining industry by geologists and geostatisticians to estimate and classify Mineral Resources. In theory exactly the same methods can be used to estimate PAF waste locations and volumes.In practice the number and spatial distribution of dedicated PAF waste samples at feasibility stage is typically so small that it is almost impossible to estimate the spatial distribution of PAF material with any degree of confidence at all. Consequently, the common approach is to characterise a few samples from a lithological unit and then assume that they represent the unit as a whole. This approach, however, can be fraught with risk.This paper describes some of the findings of SRKÆs evaluation of several coal projects with respect to PAF waste evaluation and highlights some common misconceptions held by people working in this area that do not have a knowledge of statistics or geostatistics.CITATION:Kentwell, D, Garvie, A and Chapman, J, 2012. Adequacy of sampling and volume estimation for premining potential acid forming waste evaluation using statistical and geostatistical methods, in Proceedings Life-of-Mine 2012, pp 79-88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964

By Diego Marquina, Jorge Terrones, Jose Morales

Si bien los incendios en el sector minero representan apenas el 1 % del total en todos los sectores, sus consecuencias son potencialmente críticas, por lo que resulta necesaria una evaluación constante de riesgos de incendio. En una evaluación de riesgo de incendio convencional (FRA, por sus siglas en inglés) se detallan los escenarios de riesgo de incendio a los cuales está expuesta una unidad minera, considerando las condiciones de la instalación, el análisis de los procesos, identificación de actos y condiciones subestándar, equipos u operaciones, reportes de incendio o amagos, entre otros factores que permitan identificar y analizar los escenarios de riesgo de incendio para definir su nivel de criticidad y aceptación del riesgo. Este enfoque diferenciado de FRA busca priorizar la inversión en protección contra incendios, al tomar en cuenta una tolerancia específica al riesgo de incendio, vida útil de la mina y la continuidad de procesos o recursos críticos para la operación en un nivel mínimo tolerable.

Sep 20, 2019

By J. L. Eakin

A method was developed by the Bureau of Mines in the laboratory and in the field to relieve capillary waterblocks in gas wells. Impaired gas permeability was improved by this inexpensive chemical treatment which lowers the surface tension of the water held in the capillaries of the formation. Effectiveness of the alcohol-surfactant treatment was tested with a variety of chemicals and with sandstone cores cut from rocks having relatively low permeability. Field tests on 20 gas-producing and storage wells demonstrated the effectiveness and limitations of the method. The productive capacity of some wells was doubled by the treatment. The final test was evaluated by the neutron logging technique for measuring changes in apparent liquid saturation. Maximum apparent liquid saturation was reduced by 52 percent; gas production rate increased from 2.3 to 3.5 MMcfd (million cubic feet per day).

Jan 1, 1965

By E. D. Gardner

This is one of a series of papers written for the consideration of operators of small gold and silver mines in the West. The paper discusses smelting schedules, general smelting practices that have a bearing on rates, and the reasons for penalties or credits for certain constituents of ores. Crude gold and silver ores generally are shipped to smelters only when milling facilities are not available; however, high tailing losses in milling a high-grade or refractory ore or low smelting rates because of the fluxing value of an are may make direct smelting more economical.

Jan 1, 1936

By G Britton, P Moynagh

As more than a few mines gradually sink under the weight of emails, whiteboards, notice boards and ever more complex spreadsheets, the holy grail of effective short-term interval planning and control in underground mines is as far away as ever. Despite the mining industry investing ever greater amounts in planning and Enterprise Resource Planning systems, short-term plans become ever more complex and rigid. What the industry desperately needs are not more ‘disembodied voices down the speaking tubes’, but flexible and effective planning systems that encourage people to make reasonable commitments to each other so that everyone can work as a coordinated team to complete the work required each shift.One solution to the challenge has emerged. This paper describes the ‘Fewzion’ shift planning and short interval control system which has been developed at Anglo American’s Moranbah North and Glencore’s Oaky Creek coalmines in Central Queensland. Fewzion has drawn on management theory embodied in Management Operating Systems, Lean and Theory of Constraints approaches to continuous improvement to play a key role in both mines achieving record breaking tonnages.In addition to explaining the Fewzion approach, a case study is presented describing how Anglo American’s Moranbah North improved production by 39 per cent in 2014/2015 and won ‘Coalmine of the Year’ two out of the last four years and how Glencore’s Oaky Creek sustainably improved monthly development meters by 34 per cent within two months of implementing Fewzion.CITATION:Moynagh, P and Britton, G, 2017. How a frontline planning and commitment system improves trust, commitment and results in operations, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 235–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By W. T. Millar

Field reconnaissance and laboratory tests on clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

By Carlton E. Brown

Sand, which is used widely under the wheels of mine locomotives to prevent slipping, is an important source of silica dust breathed by some employees of certain mines, such as those having appreciable grades on haulageways. The sand, as received, contains dust, and other dust is produced by passage of wheels of the train over the sand. Dust is disseminated into the air by such means as handling during unloading, drying, transporting, underground, sprinkling on the rails, passage of trains over Sections where sand is being or has been used, and walking over deposits of sand (or the dust thereof) on the haulageway. The disseminated dust is inhaled not only by persons in the immediate vicinity but also by others to whom the contaminated air travels. The inhalation of this must should be prevented to eliminate any possibility of the material causing silicosis (sometimes referred to as miners&apos; consumption, miners&apos; asthma, miners&apos; phthiris, or miners&apos; lung) and defined by the American Public Health Association4/ as: A disease due to breathing air containing silica (Si02), characterized anatomically by generalized fibrotic changes and the development of miliary nodulation in both lungs, and clinically by shortness of breath, decreased chest expansion, lessened capacity for worm, absence of fever, increased susceptibility to tuberculosis (some or all of which symptoms may be present), and by characteristic X-ray finding.

Jan 1, 1944

By P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mining and exploration properties have a unique set of technical risks. Privately-owned companies considering investing in the resources sector can optimise their investment decisions by adopting a systematic technical assessment of acquisition assets, similar to the approach commonly adopted by public financial institutions and publicly-listed companies.Technical due diligence provides a process to identify key geological, mining, geotechnical, metallurgical, environmental and social risks and opportunities and determine the most likely business case and valuation of assets. Technical due diligence is commonly carried out in parallel with legal, commercial and financial due diligence, often involving the acquirer, to maximise the understanding of the investment.There are significant advantages in investors conducting a comprehensive technical due diligence, which typically involves site visits and project assessment to international standards by an independent, multidisciplinary team of experts. The outcomes provide the opportunity for the investor to make early, informed decisions and to understand and manage risks.Technical due diligence may be carried out at several stages: when considering and weighing up a number of investment options, prior to and during a transaction or immediately post-transaction. In the first stage, the outcomes will inform the choice of investment and, more particularly, whether there are any fundamental flaws in the projects being considered. In the second stage, due diligence outcomes can inform the level of investment and approach to risk management and planning. In the third stage, risks and opportunities can be investigated in more detail, allowing the investor to consider the best options to reduce risk and maximise the benefit of the investment.This paper presents a summary of the technical due diligence assessment process, its benefits to investors, common risks in mining and exploration projects known to cause mining asset write-downs and principal technical due diligence approaches.CITATION:Keogh, A, Stoker, P and Thomas, M, 2015. Benefits of due diligence in private equity mining investments – maximising value and unearthing common risks , in Proceedings PACRIM 2015 Congress, pp 115–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Charles Smeal, Robert J. Schafer, Max Quantinetz

Normally metal powders cannot be ground to sub-micron sizes because of welding and agglomeration phenomena. Through the use of selected grinding aids and grinding fluids, nickel and other metal powders have been ball-milled as fine as 0.1 It was found that certain inorganic salts are more effective grinding aids for metal powders than conventionally used surfactants. METAL and alloy powders are used to produce reagents, pigments, coatings, solders, brazes, and parts for industry by powder metallurgy techniques. They are also combined with refractory compounds to produce cermets and dispersion-hardened products. One of the interests at the Lewis Research Center has been to explore the potentialities of the dispersion strengthening process. Since the work of Ir-mann, many investigators have shown that the strength of dispersion-hardened products may increase with decreasing interparticle spacing.24 One approach to achieving small interparticle spacing is to combine fine refractory compounds and metal powders, preferably below 1 in size. In attempting to obtain fine metal powders, it was found that until very recently the best that could be obtained from commercial suppliers, particularly of ductile metals, was about 1.0 . Interest was therefore developed in providing finer metal powders for dispersion-hardening studies. Information obtained from the literature, from others working in the field, and from prior experimental work performed at NASA, led to a consideration of ball-milling as a technique to produce the desired materials. Some of the variables associated with ball-milling are the size, material, and nature of construction of the grinding container; the nature and amount of the grinding material and material to be ground; and the nature and amount of the grinding liquid and grinding aid, if employed, and the grinding time. In all ball-milling, welding and agglomeration can oc- cur as well as grinding. Because of the tendency of ductile metals to weld together, they are difficult to grind.5 The ultimate particle size obtained on grinding is generally the one at which the rate of grinding becomes equal to the rate of welding. To help delay welding and thus obtain smaller particle sizes, grinding aids are often employed. The principal objective of this investigation was to produce submicron metal powders by ball-milling the powders with selected grinding aids and grinding fluids. A secondary objective has been to attempt to explain the variations observed in grinding behavior by considering possible grinding mechanisms and correlating various parameters with grinding effectiveness. Three groups of ball-milling experiments were run; one in which the grinding aid was varied, a second in which the grinding fluid was varied, and a third in which the material being ground was varied MATERIALS, APPARATUS, AND PROCEDURE In the first group of experiments in which the grinding aid was varied Inco Carbonyl Grade B nickel powder initially 2.5 (all sizes refer to average particle size as measured by Fisher Sub -sieve Sizer) was used as the material being ground and 200-proof ethyl-alcohol as the grinding fluid. Surfactants, representative of typical organic structures, were selected as grinding aids. Inorganic salts used as grinding aids were chosen on the basis of the size and valence of their ions. Water soluble salts were used in order to facilitate their removal from the slurry after grinding. In the second set of experiments, grinding of the 2.5- Ni powder was tried in four different grinding liquids; water, cyclohexane, n -heptane, and methy-lene chloride. In this study seven grinding aids selected from those tried in the first group of experiments were employed. In the third group of experiments 200-proof ethyl alcohol was again used as the grinding fluid to mill Cu, Cr, Fe, Ag, and Ni powders of various initial particle sizes&apos; All mill charges contained 300 ml of grinding liquid and 3000 g of 1/2 in. stainless steel balls. When inorganic salts were used as the grinding aid, 70 g of salt and 210 g of metal powder were employed, and with surfactants 6 g of grinding aid and 300 g of

Jan 1, 1962

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By F. Grant

"General *The mining experiences of the coal mining industry in Western Canada have been extremely varied, with the mining companies having to adjust their operations or fail due to the harsh economy of the country in the first part of the century. The bituminous or mountain mines had the railways as main consumers with, at times, optimism that potential steel producers would require metallurgical coal. The prairie and foothills mines mainly provided household fuels, with the fine coal sold to local thermal power plants at discounted prices. In practically all cases fuel competition was very keen, and the less successful mines ceased operations in short-time spans. Knowledge of the parameters that governed the success or failures of the past coal operations should be of value to the present and future mining companies. The initial coal mines were small and were started to supply local demand. These mines had little in the way of capital machinery, engineering, or transportation equipment; therefore the mining methods and mine plans were very simple. The first industrial-sized mines imported most of their management and mining methods from other mining areas, mainly Great Britain. It took time to change the bias of management and mining methods to the requirements of strata characteristics, with rapid closure to those mines that were slow to adapt working methods. The main markets for coal were for household fuel, thermal power plants and railways, with very few other industrial markets developed. The economy of the period was harsh and cyclic and the coal mines were affected more than most industries by these boom and bust periods. It led to the survival of the fittest or the most efficient. Due to the economy, mechanization was introduced to the mines very slowly, with the inability to sell coal fines at a profit being another reason for the delay. Manual labour with hand tools was the main means of production. The work was heavy and arduous, and the pay was based on contract coal tonnage; therefore both men and management paid close attention to details so that nonessential work could be eliminated. Mine openings were dimensioned so that coal could be loaded easily by hand and support requirements were kept to the minimum. Transporting and handling the timber supports required heavy labour; thus the most efficient dimensions were chosen to suit the strata. On the other hand, during the main production seasons the mines tried to make the strata stress work for them so that the pressure was kept on the coal face to keep the coal loose while the strata, a short distance back, was induced to cave to minimize the abutment stresses. This caused mining to be an art, using skills developed by experience with the strata. This led to the development of efficient mine layouts with the openings dimensioned to the strength of the strata and the type of support available. The lack of capital and mechanization, and the manual labour, induced the mines to correlate their service and haulage systems with their mining methods. This caused many innovations that proved very practical."

Jan 1, 1985

By H. A. Schrecengost

Information presented herein was gathered by examination of 29 fluidized- bed thermal coal dryers and by conferences with manufacturers and users of such equipment to determine what safety features could be incorporated in design, installation, and operation to minimize fire and explosion hazards. Fire and explosion hazards are inherent in certain types of coal dryers in that high temperatures are employed; the sizes and volatility of material handled are capable of propagating explosions; and drying gases are seldom, if ever, low enough in oxygen content to prevent ignitions of dust clouds, distilled gases, or their combinations. This is especially true for fluidized- bed dryers in which the coal is dried in air suspension and in which atmospheric air is constantly introduced to temper the heated furnace gases. Occurrence of fires on heated bedplates, in dust collectors, and in hot gas inlets was common in nearly all the dryers examined. Forceful explosions which produced external effects had occurred in 11 (39 percent), and internal "puffs" or "bumps" had occurred in at least 24 (79 percent) of the plants examined in the study.

Jan 1, 1965

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015