Search Documents

Development of the Greenvale orebody, containing 40,000,000 tonnes of nickel ore, began in 1971 and production commenced in 1974. Annual capacity is 2,800,000 wet tonnes. The variations in ore grade and physical characteristics which occur throughout the ore- body had a major influence on the selection of mining methods, grade control procedures, and equipment. After removal of overburden by scrapers, ore is excavated by draglines sidecasting into windrows. Feed to the crushing plant is .reclaimed by front end loaders into rear dump trucks according to a grade selection pro- gramme. After crushing, ore is stockpiled into blended units of ore of required quality. Ore is stacked and reclaimed for train loading using techniques designed to give maximum mixing of ore characteristics through Bach unit. These procedures are repeated on discharge at the plant site at Yabulu. The railway, constructed by Queensland Nickel Pty. Ltd. to Q.G.R. standard, and operated by the Q.G.R., is 216 km long and includes eight major bridges and three tunnels. Two trains per day, one of four locomotives and 92 waggons, and one of three locomotives and 69 waggons, haul crushed ore to Yabulu. Train loading is semi-automatic. A small township and associated services have been constructed for employees at Green- Vale.

Jan 1, 1974

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978

By Scott Tzcrner

WITHIN recent years people have begun to realize the importance and significance of the mining and allied industries. The leading part the engineer plays in civilization is becoming recognized. However accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business. It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization, but on the whole, the magnitude of the-industry is underestimated. In this paper I shall call attention briefly to the importance of mining in the United States, in Canada, and in the world. Ordinarily, the annual primary mineral production of the United States is about $5,500,000,000. The average for the last 5 years has been a little over that, but last year, sadly enough, it was less than 31/4 billion. Just now, we are on the decline, and have been for the last two years. In Canada, the 5-year average was about $268,000,000, and last year it was 227 million. Due in part to gold mines (in 1930, for the first time, Canada's gold production exceeded that of the United States), the Canadian average is holding up better than ours. Average world mineral production over the last -5 years has been estimated at about $12,000,000;000 whereas in 1931 it was less than than 8 billion.

Jan 1, 1932

By A Moreira, A B. De Souza, S Latchireddi, E Faria

Material transport plays a significant role in the efficiency of horizontal grinding mills - autogenous (AG)/semi-autogenous (SAG)/ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a greenfield milling operation at Mirabela MineratpoÆs SantaRita Nickel operation located in north eastern Bahia in Brazil. This grinding circuit was commissioned in October 2009, was designed as a typical SABC circuit to grind 4.6 Mt/a (575 t/h) to produce a P80 of 125 ¦m with ten to 12 per cent ball charge in the SAG mill. However, it has been operating as an ABC circuit without any grinding media in SAG mill. The nameplate design capacity was achieved in few days and was gradually increased to an average of +800 t/h, still operating in ABC mode. The Santa Rita grinding circuit consists of one 30 ft + 15.4 ft 8.5 MW SAG mill fitted with Outotec patented Turbo Pulp Lifters (TPLÖ) in closed circuit with a HP400 short head pebble crusher and one 20 ft + 28.4 ft 5.5 MW Ball Mill in closed circuit with a Warman cyclone cluster fitted with 10 + 26 in CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimisation and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed.CITATION:De Souza, A B, Latchireddi, S, Moreira, A and Faria, E, 2012. Application of turbo pulp lifter in greenfield operation - Mirabela SantaRita nickel operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By L. E. Schultze

Experiments were conducted by the U.S. Bureau of Mines to verify enhancements due to chloride and surfactant additions in the leaching system of chalcopyrite with ferric sulfate and sulfuric acid. A statistical experimental design was used and equipment was designed to eliminate contributions from changes in solution electrochemical potential during the course of the measurements. Results confirmed that chloride additions increased chalcopyrite leaching by as much as 94 pct over the electrochemical potential versus hydrogen electrode range of 630 to 750 mV at pH 1.7 and 50°C. Total iron concentration had no effect over the range of 1 to 5 g/L. The effect of surfactant addition was less well defined. While additions of LA 790 (a polyoxyethylene lauryl ether) resulted in increased copper leaching in several of the tests, the differences were too small to be statistically significant. No interaction effect could be verified.

Jan 1, 2010

By Wheeler North

THE United Eastern Mining Co.'s property is located in the Oatman, Gold Roads mining district of Mohave County, Ariz. The mine and mill are some 26 mi. (41.8 km.) southwest of Kingman, the nearest railway connection. The ore consists of a mixture of calcite and quartz with some andesite. The values, which are mainly gold, alloyed with approximately 34 per cent., by weight, of silver, are extremely fine so that fine grinding is a most important factor in extraction. The milling process, briefly, consists of single-stage, coarse-crushing, two-stage ball milling in cyanide solution, followed by combined mechanical and air agitation, and by straight counter-current decantation. The Merrill zinc-dust precipitation method is used to recover the values, and is preceded by the Crowe vacuum treatment of the solution. The most notable features of the plant are the absence of filters, and the use of short peb mills loaded with steel balls, for fine grinding. As originally designed, the capacity of the mill was to be 200 tons per day, although the grinding end was to be capable of handling double that amount. By adding extra agitators and thickeners and by some alterations to the grinding end, the daily capacity has been raised to 285 tons. This, it is hoped, may be increased to 300 tons during the warm months of the present year. TONNAGE MILLED PER DAY 1917 average 234 Maximum month 272 Minimum month 146 1918 average 253 Maximum month 276 Minimum month 217 As this article primarily deals with plant operations, those interested in the mechanical description are referred to the article by Mr. Otto Wartenweiler,1 the designing engineer, which gives the details and costs of design and construction. The following changes have been made since that article was published:

Jan 8, 1919

By Satu Strömberg

Four different nickel concentrates were oxidized in a laboratory scale laminar flow furnace in simulated flash smelting conditions. The major nickel- and iron-bearing minerals in the con- centrates were pentlandite, violarite, gersdorffite, and pyrite and pyrrhotite, respectively. Thermal decomposition, ignition and oxidation behavior of nickel and iron sulfides were examined by using optical and scanning electron microscopy. General reactivity of the concentrates was monitored with sulfur removal which was most effective in violarite-based concentrate. Pentlandite-concentrates needed higher experimental temperatures for complete desulfurization and gersdorffite-based concentrate contained 5 - 10 % of the original sulfur even in the most oxidizing conditions studied (1 100°C, 50 vol-% 02). The reactivity of the iron minerals was found to depend on the other minerals present in the concentrate. In this paper, the observed re- action products and mineralogical changes are presented and preliminary conclusions of possible reaction mechanisms of nickel-bearing minerals are discussed.

Jan 1, 1997

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

By S. Frimpong

Cable shovel requires continuous monitoring through excavation to achieve reliability, longevity and economic usage. The operating environment and the stress and deformation fields on the front-end assembly must continually be monitored to avoid random fatigue failure. In this paper, the authors advance frontiers of cable shovel reliability through real-time stress and deformation monitoring during excavation. Cable shovel boom stress and deformation analysis are developed using a combination of flexible and rigid body approach. A virtual prototype is developed to simulate the cable shovel excavation in oil sands and to examine the motion, stress and local deformation of the boom. A numerical example is used examine cable shovel boom durability using stress and deformation fields simulation. The results show that stress and deformation are large around the joint between the upper body and the boom. The simulation of the effect of material properties on boom deformation shows that the deformation is larger in hard formation than in soft formation. The study provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2006

By L. Q. Luo

SHP-F3200 wet high-intensity magnetic separator (HIMS) was successfully used to separate the complex and weakly magnetic iron ores being composed of specularite, limonite and siderite in Ji-uquan Iron and Steel (Group) Co Ltd (JISCO). It is more and more difficult to separate iron ores from gangues, such as quartz, jasperite and phyllite, as the properties of iron ores gradually become more complicated and refractory. Some technologies have been used to improve SHP-F3200 HIMS, including modifying angle of magnetic polar from 90°to 83°, cooling exciting coils by oil instead of air, adding reverse-washing device to wash off magnetic particles, adjusting the tooth-space of matrix from 5.0 mm to 3.5 mm or 2.5 mm, so as to enhance the recovery of fine iron ore particles. It is still difficult to meet the requirement for recovering more difficultly-separated iron and the demands for high-grade concentrate of iron. In this paper, after analyzing magnetic force exerting on iron ore particles within different separating sections of SHP HIMS, it is proposed to apply the flowing-film technique into the HIMS. Thus a new-type LY matrix is designed to form magnetic gradient vertically, combined with a special flowing-film feeder to improve the existing SHP HIMS. The moving pattern of magnetic particles in pulp in HIMS separation district also has been analyzed in this paper. And the test on the SHP-F700 HIMS shows, under the condition of iron ore containing 30.52% Fe, with particle size of ?0.074 mm accounting for around 75%, if applied with flow-film technique, the iron recovery will be up from 69.45% to 76.07%, by 6.62 percent, with the same grade of concentrates of iron. The calculation of iron yield of every size fraction and the tests showed that film magnetic separation (Film-MS) could promote the iron yield of each size fraction, denoting an excellent result of application of the film technique to SHP HIMS. The mechanism of the film magnetic separation technique is to convert the turbulent flow and disordered movement of dynamic mass particles in the pulp into a directional and ordered laminar flow along the surface of tooth plate so as to strengthen the separation effects.

Jan 1, 2014

By R. G. Sandberg

The Bureau of Mines investigated a hydrometallurgical procedure to recover gold, silver, and byproduct lead from a complex lead-zinc sulfide ore. A ferric chloride (FeCI3) preleach, at 40° C in 6 h, extracted about 50 pct of the zinc and formed insoluble silver and lead chlorides. Subsequent acid thiourea leaching, for 1 to 3 h at 40° C, extracted about 85 pct of the gold and silver. Lead chloride was solubilized from the remaining residue with NaCI brine solution at 55° C in 1 h. Lead metal was recovered from the brine solution in an electrolytic cell with an anion perms elective membrane at a current efficiency of 95 pct and current density of 100 A/m2. Spent FeCl3 leach solution was reoxidized in the anode compartment at a current efficiency between 75 and 95 pct.

Jan 1, 1986

By ALFRED D. FLIWN

ENGINEERING COUNCIL is not "about to die," as some persons are saying. Through a natural and foreseen reorganization, Council is entering a new stage of existence with enlarged power for usefulness. Its early constituents have made it possible for many more of their fellow engineers and men of other technical vocations -to take a- share in its activities, responsibilities and support. A new organization is being set up, but it is really a new embodiment of the same spirit of service. Another step is being taken toward the full acceptance by the technical professions of their obligation to the public and to one another for those services which can -be rendered only through effective organization. A brief retrospect is timely. Engineering Council was established in the spring of 1917, as a department of United Engineering Society in response to requests of its Founder Societies. .It followed various attempts of these societies to deal through joint committees with public questions affect¬ing engineers -and with inter-society affairs. These attempts had very limited results. In the new by-laws adopted by United Engineering Society, the purposes and-powers d-powers of Engineering Council were thus defined: "To provide for convenient cooperation between the four Founder Societies, for the proper consideration of questions- of general interest to engineers and to the public, and to provide the means for united , action upon questions of common-concern to engineers.

Jan 1, 1920

THE most important part of the routine survey work on a mine is the keeping up-to-date of plans and sections showing progress of stoping and development work, and the direction of the latter for the purpose of making necessary connections. Except in specialcircumstances, e.g., major horizoittal development, the exactitude required in this work is not extreme, and a method of survey in keeping with the demands of the work itself is all tbat is required.For example, no one would consider measuring the walls of a stope to a fraction of an inch; such extreme accuracy would be wasted.The stope walls being irregular, a mean is usually taken, and for ordinary purposes a survey with a limiting error of six inches is quite satisfactory for the purpose of plotting either stoping or development.It is the author's aim in this paper to describe the method in use at the North Broken Hill Oompany's British mine. This method, while being sufficiently accurate for the purpose in view, possesses the very great advantages of speed and simplicity of operation,with a minimum of necessary equipment. This latter is a very important item where several surveys on different levels have to be carried out on the one day.Let it be understood, however, that the use of this method does not dispense with the theodolite, but simply serves as a convenient adjunct to obtain details and to extend the accurate theodolite survey up rises and down winzes, and through ladderways orwinzes into stopes, where the use of a theodolite, if not actually impossible, is often exceedingly inconvenient. This is particularly so on the British mine, where a large proportion of the ore is won from narrow and complex-dipping lodes, and where vertical ore...

Jan 1, 1928

A study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fel_xS, CuFeS2, Cu2S) has been conducted using a mesophilic strain of T. 6ejtAooLcdcth4. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate ion has been monitored. Partially oxidised sulphide substrates have been characterised at regular time intervals by X-ray diffraction methods and extra-cellular organic compounds reporting into leach solution have been identified by'thin layer chromatography. The results indicate that the S¦/SO4 2 partitioning of the sulphide substrates is independent of cell inoculum size and initial pulp density and varies with solution pH, Eh, leaching time and mineralogical properties of the individual sulphide minerals. The signifi- cance of results for applications in selective flotation, coal desulphurisation and agglomera- tion has been outlined.

Jan 1, 1984

By C. H. Wright

Introduction The rapidly expanding and increasingly complex Canadian industrial structure, with the mining, metallurgical, and chemical industries as a large integral part, has, in recent years, brought greatly increased importance and value to our industrial minerals. In the modern economy of our mineral industry the importance which is due the non-metallics has been somewhat overshadowed by the great value of our large metal production and, in addition, by the glamour and fascination usually associated with the mining and treatment of gold ores. The term 'Industrial Mineral' is used in this paper in its usual sense and refers to non-metallics other than fuels. Coal and petroleum products, including natural gas, are considered as industrial minerals in those applications in which they are used for strictly chemical process purposes. Certain reduction metallurgical industries are so closely allied to chemical industries that for purposes been of this discussion no attempt has made to differentiate between them. Chemical industry in Canada today is a fairly large factor in our national economy, whereas in 1898, when the Canadian Mining Institute was born, it was very small indeed. Chemical concerns are largely dependent on industrial minerals for raw materials and process supplies and, as the country has developed industrially, so have the demands for non-metallics increased, not only by chemical industry but also by other large consumers, such as the construction and metallurgical industries. At the present time there is a greater than normal incentive prevailing for new discoveries, due to the serious lack of balance that exists in our import and export trade. This fact has resulted in intensive efforts to rectify the situation by locating new deposits and re-assessing those already known in an effort to enlarge and improve our home production of raw materials and also to extend their processing in Canada for our own needs and for export. The rapid advances in science and technology that have taken place since 1900 have also resulted in many cases of beneficiation and utilization of otherwise too low grade materials in order to satisfy current demands. The purpose of this paper is to indicate the history and the trends of the utilization of industrial minerals in established industry and to indicate the important part played by non-metallics in connection with the opening up of new industries. Some consideration has been given to the continual competition between natural and 'synthetic products and to the general tendency towards more rigid specifications.

Jan 1, 1948

By Fernando de Oliveira Boechat

As maiores pressões e temperaturas atualmente empregadas a fim de aumentar a produtividade de fornos de DRI têm resultado em um subproduto indesejado: o aumento da geração de clusters. Estes clusters prejudicam o fluxo da carga e a permeabilidade do leito. A fim de limitar o tamanho destes aglomerados o forno MIDREX dispõe de três conjuntos de quebradores localizados em diferentes posições do forno após a redução da carga. A interação entre clusters e esses quebradores, entretanto, pode também prejudicar o fluxo da carga e aumentar a geração de finos. O trabalho utilizou o método dos elementos discretos (DEM) para avaliar as energias e forças resultantes da interação entre os clusters formados e os quebradores. A descrição dos clusters foi realizada usando o bonded-particle model, disponível no EDEM. Simulações mostraram que a presença de clusters altera as forças e velocidades no entorno dos quebradores que tenderiam a aumentar a geração de finos no reator.

Aug 16, 2017

By Leoncio Méndez, Jesús Arguijo, Juan José Frausto, Daniel Castruita, Daniel Aguilar

Minera Sabinas (Grupo Peñoles), localizada en Sombrerete, Zacatecas, México, produce concentrados de cobre y zinc. Su proceso es un circuito de conminución de quebradoras y dos molinos de bolas en circuito cerrado con hidrociclones seguido de un circuito de flotación, a partir de mineral polimetálico extraído de una mina subterránea. Su problemática consiste en que la recuperación por flotación disminuye significativamente cuando minerales con contenido de pirrotita son procesados. La flotabilidad natural de la pirrotita supera la cinética de flotación de las especies de cobre y zinc y limita la capacidad de la concentradora para generar concentrados vendibles. Este artículo presenta un diagnosticó de los problemas que se tienen cuando se procesan minerales con alto contenido de pirrotita, así como resultados de un programa experimental a escala laboratorio realizado en el CIDT de Peñoles y en sitio. La investigación se enfocó en definir un esquema de reactivos para poder procesar minerales con pirrotita en su composición. Compósitos de alta y baja ley de cobre fueron usados en la investigación. Se identificó el agua de proceso como una fuente de iones calcio y sulfato. Se desarrolló un esquema de reactivos orientado a promover la selectividad de las especies de valor respecto a la pirrotita, incluyendo tratamiento del agua de proceso.

Sep 20, 2019

By A Giblett, B Putland

This paper provides a simple guiding framework for grinding circuit optimisation, focussing on common themes in past optimisation success stories, the conditions for success and techniques that can be employed to identify and define opportunities. Many significant grinding circuit improvements have been reported for operating plants, based on recurring themes such as the optimisation of mill feed size, mill liner design, process control, critical size, grinding media and classification. The paper condenses these experiences into a set of simple questions for the operator to ask, and provides guidance towards identifying and achieving the optimisation goals.CITATION:Giblett, A and Putland, B, 2018. The basics of grinding circuit optimisation, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 129–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018