Search Documents

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

By Shadia Ikhmayies

Thermo-Calc software was used to investigate the phase diagram of the calcium silicon (Ca–Si) system for the range of Si mass percent 0–100, and temperature range T = 200–1800 K. The melting points of Ca and Si deduced from the phase diagram are very close to the values obtained experimentally. Three stable intermediate solid phases were found, which are Ca2Si, CaSi, and CaSi2, where the first one appeared in the Ca rich side of the phase diagram, and the third one in the Si rich side. In addition, three eutectic points were found at Si mass percents of 3.95, 33.00, 62, and temperatures T = 1048.7, 1519.14, 1308.5 K respectively. Atomic Si (Diamond structure) is found mixed with CaSi2 intermediate phase for temperatures less than 1305 K, and mixed with a liquid CaSi for higher temperatures. These results are important for thermodynamic and metallurgic studies of these intermediate phases.

Mar 1, 2018

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By C. Samuelsson, H. Ahmed, B Björkman, A. Andersson

The cost of raw material and energy is a continuing driving force towards working with increasing the recycling of ore based steelmaking residues. In Sweden no on-site sinter plants are operated at the integrated steelworks. Instead, selected residues from the plant are incorporated in a cold bonded briquette product which is recycled to the process via the blast furnace (BF). Since the BF sludge is the major bleed of zinc out of the furnace it is required to be de-zinced prior to recycling in the briquette product. In the present work landfilled BF sludge has been characterized with respect to chemical composition, particle size distribution, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The sludge was also subjected to laboratory scale hydrocyclone trials aiming at reducing the zinc content making the sludge viable for recycling. The results suggested that the sludge had been agglomerated prior to the characterization and hydrocyclone treatment. The zinc removal using the hydrocyclone was discussed.

Jan 1, 2015

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By R. O. Pynnonen

This circular is a study by the Bureau of Mines of 346 accidents in underground iron-ore mines of the Lake Superior district from June 1949 to August 1954. These accidents caused 354 lost-time injuries, including 28 fatalities and 2 permanent-total disabilities. The accident reports were analyzed by the Bureau to show the causes of injuries and the time charges and unsafe practices or conditions that caused the accidents. Also shown are the times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 14 percent of the total number of Lake Superior district underground mine accidents that resulted in lost-time injuries during the period covered. These facts are presented to aid accident-prevention measures in underground mines and as a record for measuring future safety accomplishments.

Jan 1, 1956

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By A. Newman, M. Goycoolea

"In this paper, we consider an underground production scheduling problem consisting of determining the proper time interval or intervals in which to complete each mining activity so as to maximize a mine’s discounted value while adhering to precedence, activity durations, and production and processing limits. We present two different integer programming formulations for modeling this optimization problem. Both formulations possess a resource-constrained project scheduling problem structure. The first formulation uses a fine time discretization and is better suited for tactical mine scheduling applications. The second formulation, which uses a coarser time discretization, is better suited for strategic scheduling applications. We illustrate the strengths and weaknesses of each formulation with examples.IntroductionProject scheduling is an important aspect of underground mine planning that consists of determining the start dates for a given set of activities so as to maximize the value of a project while adhering to operational and re-source-availability constraints. Important activities that require scheduling include development, drilling, stoping and other ore-extraction techniques, and backfilling. Precedence relation-ships impose an order in which activities can be carried out based on their location in the mine: for example, the activity a associated with development of an area must be completed before the activity a´ associated with extraction of that same area can begin. Re-sources include attributes of the mining operation, such as the amount of extraction and mill capacity available per time period, and are determined by capital and equipment availability and other factors. In this paper, for our set-ting, resource-availability constraints consider the amounts of material that can be extracted and sent to the mill — that is, processed — per time period."

Mar 1, 2017

By Marcello Rodrigues Cruz

O presente estudo objetivou avaliar as diferenças no processo de flotação entre as frações -0,150 +0,038 mm e -0,038 mm, bem como a redução de custo no processo de flotação. Verificou-se que as frações apresentam resultados bem distintos em recuperação mássica, recuperação metalúrgica, seletividade, razão de enriquecimento e teor de sílica no concentrado, condições ideais de adição de reagentes e qualidade final de concentrado e rejeito entre as frações e também se comparada a ao experimento controle, composto com a mesma amostra sem ser fracionada. Através dos testes executados segundo o planejamento fatorial, foram estabelecidos os pares de variáveis ótimas para a flotação para cada fração distinta e as possíveis otimizações utilizando-se a ferramenta estatística. Os resultados obtidos dos testes de bancada apontaram que a amostra composta e as frações separadas apresentam comportamentos distintos quanto às variações dos fatores dosagem de amina, dosagem de amido e pH de flotação e que os resultados do processo melhoram significativamente em relação ao processo sem o tratamento fracionado.

Aug 1, 2018

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

By A. J. Williams

"IntroductionAN EXCELLENT paper entitled Potash Discoveries in Western Canada (l) was presented to the 1948 Annual Meeting of the C.l.M. by L. Heber Cole, of the Department of Mines and Resources, Ottawa. In the intervening three and a half years, the search for oil and gas in Saskatchewan has added considerably to the information available on the occurrence of potash. It is the purpose of this paper to summarize the additional data. For greater clarity, it may be useful, first, to recapitulate some of the highlights of Mr. Cole's paper.Underlying the western plains of Canada there is a large deposit of sodium chloride, believed to be of early Devonian age. Associated with the sodium chloride are certain potash salts, primarily 'sylvinite,' a mechanical mixture of sodium chloride (halite) and potassium chloride (sylvite) crystals. The potash salts, when present, are usually near the top of the salt formation, though in at least one well they were found near the central part of the deposit. Cole reported on some seven wells in Saskatchewan which had encountered appreciable amounts of potash; these were the Ogema, Radville, Davidson Nos. 1 and 2, Prairie Salt Nos. 1 and 2, and Verbata wells. Depth of potash from surface ranged from 7,653 feet in the Radville well to a minimum of 3,466 feet in the Verbata well. Such depths do not compare favourably with those at which the potash is found in mines in the United States, France, and Germany, where about 1,000 feet is the average. The greatest concentration of sylvite encountered was in the Verbata well, where a bed 11 feet thick carried the equivalent of 21.64 per cent K20."

Jan 1, 1952

By M. A. Reuter, N. J. Bartie

Metals make modern societies function, and increasingly, various high purity precious and special metals endow sustainability-driving technologies with specific functionalities. These metals become heavily intertwined within products, complicating end-of-life treatment. To counteract the resulting downcycling and potential depletion of scarce resources, maximising both the quantities and qualities of materials recovered during primary extraction and recycling, processes should be a priority in the pursuit of sustainable circular economy. Adopting a process simulation approach; a digital twin for the life cycle of cadmium-telluride solar photovoltaic (CdTe PV) modules was created. The system comprises an integrated metallurgical production system that produces, among others, cadmium, tellurium, selenium, zinc, copper, and lead, all of which are required to manufacture PV modules. System-wide resource efficiency and environmental impacts are assessed using exergy analysis and life cycle assessment, respectively. Simulation of this large and complex product life cycle at a high level of detail allows for the evaluation of potential system-wide effects of various production, recycling and residue exchange scenarios aimed at maximising the sustainability of the entire system. It diminishes the need to make arbitrary choices about allocation methods for the distribution of environmental impacts in multipleoutput production systems. Furthermore, it demonstrates the key importance of metallurgy in achieving circular economy. Keywords: Circular economy, sustainability, simulation, metallurgy, CdTe photovoltaics, life cycle assessment

Jan 1, 2020

This paper presents a study about reopening of a quarry near to the geothermal region of Kntahya, Turkey. The production method was gallery blasting which resulted in very high ground vibrations. Therefore the quarry had been closed down by the local authorities about 12 years ago due to possible damages to the geothermal resources. In order to reopen the quarry, reserve estimation and production planning studies needs to be carried out as well as applying environmentally sensitive production method. The result of reserve estimation studies showed approximately 12.5 Mt reserve in the area. The market studies indicated that annual production of 600 000 tonnes could be sold. These results justify to reopen the quarry. In order to overcome environmental problems, bench blasting production method instead of gallery blasting has been planned. This method enables to design a drilling blasting pattern that will almost result in no ground vibrations.

Dec 6, 2010

By A. H. Mokken, G. K. I. Blendulf, G. J. C. Young

A study of the arrangements for pulp discharge on pebble mills, and their influence on mill performance by A. H. MOKKEN, B.Sc. (Eng.) (Rand) (Fellow), G. K. I. BLENDULF, M.Sc. (Stockholm) (Member), and G. J. C. YOUNG, B.Sc. (London) (Member) Although used for many years in the gold-mining industry, the conventional pan lifter at the discharge end of a pebble mill has hindered attempts at optimization of speed of rotation and pulp flow. A theoretical approach to flow patterns in pan lifters has pointed to limitations in the capacity of these lifters, with capacity decreasing as speed of rotation is increased. Complete elimination of the pan lifter by the adoption of peripheral or end discharge has resulted in a marked increase in pulp flow and an improvement in power utilization. Assays of the gold content of pulp discharged after a mill stoppage from mills fitted with pan lifters show values well in excess of the current milled grade, which indicates an accumulation of gold particles in the mill and, therefore, a longer retention period. The same could apply to other heavy minerals and metals present in the ore feed or worn off mill linings and metallic grinding media. Examples are osmiridium, fine iron and iron alloys, and copper and sulphide minerals. This phenomenon is attributed to the higher specific gravities of these metals and minerals, causing them to migrate towards the mill shell, from which position they are not readily removed by the lifters at the discharge end of the mill. The close association of gold particles with iron and sulphide minerals in the crevices of mill liners might be conducive to the formation of coatings on the gold. Assays of samples of milled pulp taken from a mill designed for end discharge show a lower accumulation of gold. The accumulation and nature of these gold particles are being studied at present. With increasing diameters of pebble (or autogenous) mills, peripheral or end discharge appears to be the preferred method of pulp removal.

Jan 5, 1975

By T. KIRKE ROSE

A Discussion of the paper by H. O. Hofman and M. G. Magnuson, read at the Lake Superior meeting, September, 1904. (British Columbia Meeting, July, 1905.) T. KIRKE ROSE, London, Eng. (communication to the Secretary*`) :-The authors have shown that, under certain conditions, the rate of dissolution of gold by chlorine and bromine is re¬duced by the addition of 10 per cent. of silver to the gold, and that the action is almost stopped when the silver amounts to 30 or 40 per cent. of the alloy. Even if full recognition is given to the practical way in which the work was done, how¬ever, it is to be regretted that Prof. Hofman and Mr. Magnuson did not determine the temperature at which the experiments were carried out. From the details given it may be inferred that the temperature was raised by chemical action by about 20° C. when 21 g. of sulphuric acid were added, and that the mixture was then slowly cooled down during the experiment. When bromine or very weak chlorine solutions were used, there could not have been any perceptible heating action. As the action of both chlorine and bromine is aided by heat, it follows that the stronger solutions of chlorine were given an unfair advantage over the weaker solutions and over bromine. If the temperature had been the same in each case, I do not think that the conclusions given oil p. 432 of the Bi-Monthly Bulletin, March, 1905, 1 would have been found to be justified. (This is speaking generally. In barrel-treatment the conditions are similar to those in the experiments.) The superior speed of bromine as compared with chlorine at equivalent strengths is not yet disproved, and the differences noted between strong and weak solutions of chlorine may have been largely a function of the temperature. Moreover, the authors used somewhat coarse particles of gold

Sep 1, 1905

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

By R. T. Jones

Keywords: Pyrometallurgy, DC arc furnace, myths, history, hollow electrode, radiation, resistance, flicker, AC DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from non-ferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014