Search Documents

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By Wei Tsu Jinan

A liga de alumínio AA 6351 é uma liga endurecível por precipitação coerente do sistema Al-Si-Mg, contendo adicionalmente Mn e Fe. Neste trabalho foi realizada a caracterização microestrutural de um tubo extrudado de parede grossa da liga AA 6351. Foram utilizadas várias técnicas complementares de caracterização microestrutural, tais como microscopia óptica de luz polarizada, microscopia eletrônica de varredura eletrônica (MEV), espectroscopia de raios X por dispersão de energia (EDS), difração de elétrons retroespalhados (EBSD), medidas de dureza e de condutividade elétrica. Foram analisadas as principais características dos grãos e precipitados presentes. Foi detectada e analisada uma zona periférica de grãos grosseiros nas proximidades das superfícies externa e interna do tubo.

Oct 30, 2017

By E. J. ENGEL

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Grenville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New York State include earth materials of differ- ent chemical and mineral compositions. In general the mineral talc is sub- ordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits.

Jan 1, 1949

Mineral deposits in New Zealand whose origin can be ascribed to primary magmatic segregations are associated with mafic-ultramafic complexes related to two orogenic episodes which took place during Palaeozoic and Mesozoic times. These mafic-ultramafic complexes are essentially of two types. One is ophiolitic and has podiform chromite mineralisation presumably formed below a spreading ridge. The other type occurs as intraplate layered intrusions in which Fe-Cu-Ni sulphides and Fe-Ti-V oxides have formed as a result of liquid immiscibility with the host magma, and have subsequently accumulated by gravity means. Generalised descriptions are given for some deposits in NW Nelson, Fiordland and Marlborough districts.

Jan 1, 1980

By Louis Cabot

A pilot plant of the Modular Gold Processing Unit (MGPU) was designed, installed and operated, over a 8 months period, by RSW-Béroma, at the Granada Mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up as well as exploitation results, including productivity and profitability curves, are given for a small scale mining operation in comparison with larger ones. Copyright ã 2001 CIM

May 1, 2001

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By S. Mischler, J. Noll, G. Schnakenberg, A. Bugarski, M. Crum

Diesel particulate filter (DPF) systems and biodiesel fuels are two of the most promising technologies available to the mining industry to reduce the exposure of underground miners to diesel particulate matter (DPM). A study has been conducted to estimate the potential of DPF systems and biodiesel blends to reduce DPM emissions from production vehicles. Results of testing three DPF systems in an isolated zone showed 88% to 99% reductions in elemental carbon concentrations. The test results also show that biodiesel blends, B20 and B50, reduced the elemental carbon concentrations in the mine air by 26 and 48 percent, respectively.

Jan 1, 2004

By H. V. Fairbanks

It is estimated that millions of tons of coal fines are unsaleable each year due to difficulty of drying them economically with conventional mechanical dewatering and thermal drying equipment. The difficulty is due to the fact that coal of small particle size presents a large surface area with polar groups which have a great affinity for water. In order to remove this water thermally, a high temperature is necessary which oxidizes the surface of the coal. This substantially reduces the heating value of the coal. If drying could be satisfactorily carried out at a lower temperature, much more of the heating value of the coal fines could be retained. It was conjectured that acoustic energy applied during the drying process might prove to be of value since acoustic energy has the property of producing cavitation at a liquid-solid interface when the intensity is sufficiently great. This cavitation process produces water at room temperature which can be carried away from the solid surface by a flow of relatively cool air. Hence, moisture removal is made possible at a lower temperature.

Jan 1, 1966

By H. Kenworthy

Small batches of fluorspar flotation concentrates were made into nodules and pellets on a laboratory scale. Several of these were rated acceptable by laboratory evaluation methods. The most satisfactory pellets were produced by mixing fluorspar with about 12.5 percent of water, by weight, and 4 percent of organic binders. These binders) for the most part) originated from petroleum and wood-pulp industries. They were generally difficult to handle and were not easily incorporated with the fluorspars tested. Most of them seemed to have an aversion for damp fluorspar and had to be forcibly mixed with the fluorspar; which was then formed into pellets by pressure. Substitution of fuel oil in varying amounts in the binders enhanced the mixing and penetrating qualities of these binders but at the same tire tended to make the pellets more porous. Tall oils performed the same function to a lesser degree and usually decreased the water absorbency of the finished pellets. Heat-treating temperatures to set up these binders were moderate -about 5000 F. for 30 to 50 minutes was usually enough for both drying and heat treating. Nodules made with 1-1/2 to 2 percent of bentonite as a binder were easily mixed and formed. They required a high degree of heat (about 1,500° F.) to develop their strength and were quite water-absorbent when finished. Two fluorspars were examined for weight and fluorite loss after heat treatment at similar temperatures. Both showed a definite wej.ght and analytical loss of fluorite. Bentonite was used also as a binder to successfully nodulize finely ground oxides of iron, manganese, and nickel.

Jan 1, 1951

By Bruno Pinheiro da Silva

Controlar a distribuição de carga do Alto Forno é fundamental para o controle de processo, e através de sua otimização, dentre as mais variadas configurações operacionais, busca-se lograr da estabilidade do processo e aproveitamento do gás no interior do reator. Para tal, utiliza-se um sistema de carregamento, sendo o mais usado na atualidade o do tipo Bell Less Top com calha rotativa. Durante o carregamento do forno as partículas passam pela calha rotativa, resultando em abrasão dos elementos de desgaste que por sua vez, altera a geometria da mesma, gerando alterações na trajetória das partículas carregadas e a mudança de trajetória pode perturbar a marcha do Alto Forno. Nesse contexto, a boa condição da calha passa a ser um fator essencial para a manutenção da estabilidade operacional. O presente trabalho, aplica o método dos elementos discretos (DEM) para caracterizar os efeitos do desgaste da calha na trajetória do material descarregado, podendo assim avaliar melhor os distúrbios na estabilidade do Alto Forno, e com isso a indicar o melhor momento para troca da calha.

Oct 30, 2017

By B. Farshadi, B. Asi, M. J. Habibian

"Dare-Zereshk deposit is one of the deposits supplies ore for Taft copper Complex in Iran Yazd province. This deposit is situated underneath a village the same name. Prior to mining activities, the village and its agricultural lands should be dislocated and deserted. This paper discusses about sustainability factors in this area including: Social and environmental effects of mining, dislocation and substitution of communities, created and lost jobs, financial and economic factors, quality of life index, infrastructures and post-mining land use. Studies have been performed by coupling Geographical Information System (GIS) with decision support tools such as Multi Attribute Decision Making (MADM), Through these studies revealed that considering the infrastructures developed for mine and plants, earned incomes and changing the community, mining activity in this area not only increases the social and regional sustainability but also improves it to a higher level."

Jan 1, 2011

By James W. Martin

This user?s manual analyzes the application, selection and performance of hopper/crusher/conveyor systems used with front-end loaders in surface mining operations. It is designed to be used in conjunction with its companion manual: "Guideline Manual for Front-End Loader Load-and-Carry Applications" Aspects of the application are covered as well as design considerations of the hopper/crusher/conveyor units. Lists of equipment manufacturers, crusher specifications, together with a series of checklists, are included for preliminary analysis.

Jan 1, 1982

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By Myles E. Robinson

During the last decade there were pronounced changes in the competitive pattern of the fossill fuels It is proposed to trace these trends and describe inter-fuel competition, first as it relates to the economy as a whole and then more specifically to examine competition of the fossil fuels as these share the electric utility market. Table 1, Competitive Fuels and Water Power Used in the United States, 1950-1959, shows the growth in the consumption of coal, oil, gas and water power &apos;during the past decade. Uses which are not directly competitive among the fuels, such as tractor fuel, carbon black, and consumption of petroleum products in the making of synthetic rubber, have been excluded from these statistics. The experience of the three fossil fuels in competition since 1950 shows natural gas expanding more rapidly, than oil by roughly twice as much, 219.0 percent&apos; compared to 124.1 percent growth in B.t.u.s of oil consumed in the ten-year period. Percentagewise, water power little more than held its own, and coal, including anthracite, actually decreased more than one-fifth.

Jan 1, 1961

By Fatma Arslan

The lateritic nickel ore sample subjected to this experimental study was taken from Çalda ore deposit (Turkey) and contains 1.43% Ni and 0.105% Co. Mineralogical investigations showed that the ore sample contains asbolane, chromite, limonite, hematite, goethite, lepidocrocite, magnetite, serpentine, and clay type minerals together with chalcedon, quartz, calcite, and chlorite. In the acidic leaching experiments, the effects of temperature, acid (H2SO4) concentration, and leaching time on nickel leaching recoveries were investigated. Leaching recovery versus time curves showed a parabolic trend and increasing the temperature shifted that curves to the higher values. The dissolution of nickel from lateritic ore can be explained by a shrinking core model and the apparent activation energy was found as 47.34 kJ/mol in the range given by the literature. The highest Ni and Co leaching efficiencies as 90.2% and 96.8% respectively were obtained at 80°C temperature, 200 g/L H2SO4 concentration, and 8 hours of leaching time.

Jan 1, 2006

By Juliana Gonçalves Pohlmann, Guilherme Liziero Ruggio da Silva, Eduardo Osório, Claudia Caroline Teixeira Barbieri, Hector Alejandro Picarte Fragoso, Antônio Cezar Faria Vilela

Este trabalho teve como objetivo avaliar a combustibilidade de misturas carvão nacional, do estado do Rio Grande do Sul, para injeção em altos-fornos. O estudo foi realizado através de ensaios de combustão no simulador de PCI do Laboratório de Siderurgia da Universidade Federal do Rio Grande do Sul (LaSid/UFRGS). Os carvões empregados foram carvão nacional, carvões importados e misturas destes tendo o baixo volátil importado como base. Os resultados mostraram que a combustibilidade medida pelo burnout foi proporcional ao teor de matéria volátil. Foi verificado efeito sinérgico nas misturas, onde o carvão alto volátil (CC) exerceu uma maior interação com o carvão base baixo volátil (CA) do que o carvão brasileiro (CB). Uma adição de 10% de CC proporcionou uma eficiência de combustão na mistura CA:CC superior a uma adição de até 30% de CB na mistura CA:CB. A partir de 30% de CC e 50% de CB não houve variação significativa nas eficiências de combustão em relação aos carvões individuais CC e CB.

Oct 1, 2019

CONTENTS PAGE Bronze Bearing Metals. By G. H. CLAMER 1729 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. WARING . . 1733 The Tin-plate Industry. By D. M. BUCK. Discussed by G. H. CLAMER, J. W. RICHARDS 1735 The Aluminum Bronze Industry. By W. M. CORSE 1738 Bronzes, Bearing Metals, and Solders. By G. K. BURGESS and R. W. WOODWARD. Discussed by G. H. CLAMER, R. T. ROBERTS 1742 Babbitts and Solder. By G. W. THOMPSON 1751 The Cadmium Supply Of the United States. By C. E. SIEBENTHAL. Discussed by M. L. LISSBERGER, C. W. HILL, F.- F. COLCORD . . .. . . . . 1752 Solder, Its Use and Abuse. By M. L. LISSBERGER 1759

Jan 12, 1918

By George J. Young

Discussion of the paper of George J. Young, presented at the San Francisco meeting, October, 1911, and published in Bulletin No. 59, November, 1911, pp. 839 to 872. ASKIN M. NlCHOLAS, Melbourne, Australia (communication to the Secretary) : * Professor Young deals with quite a variety of machines and methods, but, strangely enough, makes no mention of the work done by me, although he concludes with the remark that the " thin-cake continuous filters are a decided improvement over the thick-cake filters." As those interested in slime-treatment may consider that I did nothing more than to patent a process, I submit Fig. 1, showing the working-drawings of a machine, made, tested, and proved to work satisfactorily by me early in 1905. This time is prior to any work done in slime-filtration with rotating filters by E. L. Oliver or others. I maintain that a number of appliances now in use for slime-filtration infringe my patents. And after most exhaustive inquiry, I know of no machine or process, prior to my description in 1899,1 that embodied getting rid of the residues by holding them on the cloth with the vacuum, and then discharging them with back-pressure, so as to form a cycle of the operation, the result being continuous treatment. I therefore think that any paper dealing exhaustively with this subject is not complete without a reference to the work that I have done. * Received Mar. 11, 1912. 1 U. S. Patent No. 619,211, Feb. 7, 1899.

Aug 1, 1912