Search Documents

By Tanaya Deb, Sujit Kumar Pal

"Experimental investigations are carried out on failure pattern around 2D models of belled anchor piles in dry sand bed of density 15.60 kN/m3 under uplift. The models are having thickness ratio (Ts/Tb) = 0.28, 0.32, 0.38 and 0.46 and total 12 numbers tests are performed on models possessing 45° bell angle and shaft thickness 26 mm. The foundation bed is prepared with alternate dyed and non-dyed sand layers and continued upto reaching embedment ratio of 3, 4 and 5 for each width ratio. The failure points are presented with respect to meridian section of anchor in X-Y coordinate system and the equations formed are of polynomial of degree 3; and R2 values are near about 1. The developed wedge is implemented as three-dimensional axisymmetrical failure surface around similar 3D models. In the horizontal slice method vertical limit equilibrium is used for calculating weight of wedge and mobilized shear (as per Chattopadhyay and Pise, 1986) on the slip surface of each element. The summation of all elementary forces demonstrates gross uplift capacity. The initial and final failure angles are detected and parametric study is conducted on failure pattern as well as predicted net ultimate uplift capacity. Almost all the analytical data are within ± 10% variations with respect to the experimental results of uplift capacity which shows better correlations. INTRODUCTION Belled or enlarged base anchor piles are attractive and economic alternative to the geotechnical engineers for compressive load bearing capacity as well as tension anchorage. These types of anchors may be useful for foundations erected below ground water table. In light weight structures like radar tower, television tower, power pole and outdoor sign pools imbalance horizontal forces due to wind loads, are more than of those self-weight of those structures. Due to chronic tensile loads most possibly from wind loads and associated imbalanced cable tension, the legs of power transmission tower should be properly designed to be safe against resultant pull-out forces. In belled anchor pile, uplift is influenced by embedment ratio, diameter ratio; so, contributions of these parameters on failure surface influence uplift capacity. Balla (1961) first introduced non-linear failure surface in the pattern of circular arc based on Kotter’s equation (1903) and soil friction was assumed to act on slip surface. The predictive mathematical models established by Matsuo (1967), Rao and Kumar (1987), Chattopadhyay and Pise (1986), Saeedy (1987) and Ghaly and Hanna (1994); it was reported that net ultimate uplift capacity was combination of bulk weight of failure wedge and shear resistance along slip surface acting in opposite direction of wedge movement. From the literatures available till date, it reveals that the contribution of mobilised shear and weight of breakout wedge separately, demanding for more clarification depending on the on parameters like embedment ratio, diameter ratio."

Jan 1, 2015

By H. -F. Krausse

Roof failures in underground coal mines are related to the lithology and geologic structure of the roof. There are two distinct suites of roof rock above the Herrin (No. 6) Coal in Illinois, and each has distinctive patterns of structure and roof failure. In black shale-limestone roof areas, roof instability is correlated with thinning of limestone beds and presence of faults and clay dikes. In gray shale roof regions, the prime roof hazards are posed by rolls, shear bodies, and presence of coal or carbonaceous partings in the roof. Most structural features examined are believed to have formed during early stages of sediment diagenesis and compaction. Structural trends and lithologic patterns are strongly interdependent for this reason. In many cases geologic patterns are so complex and locally variable that prediction of roof stability far in advance of mining is difficult. The need for greater flexibility in roof control planning is apparent.

Jan 1, 1979

By Everard Leland

This paper, describing the mining practices at the Pilares mine, Pilares de Nacozari, Sonora, Mexico, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts. At present (1930) practically all the mineral production from the Nacozari district is from the Pilares mine of the Moctezuma Copper Co., a subsidiary of the Phelps Dodge Corporation. The ore is mined for its copper but contains associated silver in small quantities.

Jan 1, 1930

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.

By N. K. Dumakor-Dupey, G. B. Sakyi-Addo, K. J. Bansah

"Artisanal and small-scale mining (ASM) occurs in many countries around the world, and provides a source of livelihood to many impoverished local people in areas where it occurs. This paper reports the role of female participants and reasons why they engage in ASM. Field visits were made to 12 ASM sites located in the Tarkwa Mining District of Ghana to conduct interviews with male diggers and female participants. It was observed that over 100 women between the ages of 18 and 50 participate in ASM for survival. They engage in ASM largely because they have no alternative employable skills and income sources. These female participants depend on ASM to sustain the lives of their dependents. INTRODUCTION Artisanal and small-scale mining (ASM) conventionally involves use of rudimentary tools (such as picks, shovels, chisels and hammers) to exploit precious minerals and metals from the ground. It has been a major source of livelihood to many impoverished local people for more than a century. In many instances, it is the only source of income to indigenous people who have no alternative employable skills. The World Bank estimated that more than 100 million people around the world benefit from ASM which largely occurs in developing countries in Asia, Africa, Oceania, and South and Central America (World Bank, 2013). Cobalt, which is used in lithium-ion batteries to power cellphones, laptop computers, and electric vehicles, is largely produced by artisanal miners in Congo (The Washington Post, 2016). In Sudan, ASM is a significant contributor to the national economy, accounting for about 85% of total gold extracted yearly from 2010 to 2015 (Ibrahim, 2015). Also, according to the Embassy of Sierra Leone in Washington DC, USA, 90% of mineral export in Sierra Leone can be attributed to thriving artisanal diamond mining in the country (Sierra Leone Embassy, 2016). In Ghana, the ASM sector was recognized by government as a multimillion industrial activity, and through a series of initiatives, it was legalized by promulgating the Small Scale Gold Mining Law of 1989 (PNDCL 218). Presently, artisanal mining is widely practiced in two forms: licensed (registered), sometimes referred to as formal ASM, and unregistered (informal or illegal) operations, popularly called “galamsey”, a name believed to have been derived from “gather and sell” by ancient miners who could not communicate in the English language with European/British miners. The ASM sector in Ghana, like other countries, has seen a rise in female participation over the years. A report by the International Labour Organization (ILO) indicated that women account for about 15% of total workforce in ASM in Ghana, and up to 50% in Africa (ILO, 1999). Other researchers have also estimated women participants in ASM to be between 30 and 70% in Africa (Hinton et al., 2003a; Hinton et al. 2003b; Hilson, 2002). Presently, there is no reliable data from Ghanaian authorities on number of females engaged in ASM. However, data obtained from 15 ASM sites suggest that at least 40% of the employees are women. It is expected that a similar trend exists across ASM operations in Ghana."

Jan 1, 2017

By Robert F. Chaiken

An absorption-desorption model of particle reactivity was employed to describe the observed relationship between two apparently diverse phenomena which have been the subject of considerable study at the U.S. Bureau of Mines: (1) coal-rock dust reflectance and (2) coal-rock dust explosibility. The model accounts for heterogeneities in particle-size and material properties; however, in the present report, only particle-size distribution is considered. A mean particle-size parameter, appropriate to the explosion extinction process, is derived, and then taken as appropriate to describing optical reflectance. The derived form-to-function relationships for the two processes, when compared with experimental data, suggest that a problem exists with previously derived theory relating optical reflectance to rock dust concentration. A reexamination of that theory leads to a new theoretical expression, changed by a factor of 2, for the variation of rock dust concentration with reflectance which is in quite good agreement with experimental results. The current work offers justification for measuring and establishing rock dust requirements for specific coal dust size distribution(s) found in the mine-distributions that undoubtedly depend on the mining method and the type of coalbed.

Jan 1, 2010

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By A. S. Macfarlane

The South African Institute of Mining and Metallurgy was approached by the Australian Institute of Mining and Metallurgy to present a paper on the current practice in terms of the valuation of mineral projects and properties, given the development of a Code for the Valuation of Mineral Properties, developed in Australia (the VALMIN Code), and a similar Code in Canada (the CIMVal Code).This paper is the result of research and investigation into the matter, in terms of the reporting of Mineral Resources and Reserves, financial reporting practice, the Listing Rules of the Johannesburg Securities Exchange, and various practices in valuation. The paper establishes that a strong linkage has already been established between the SAMREC Code for the reporting of Mineral Resources and Reserves and the Listing Rules, and that, for completeness, a Code for Valuation needs to be developed. This Code will be similar to its international counterparts, with the necessary inclusions which are relevant to South Africa, and will provide guidelines and definitions on matters such as transparency, materiality and competency in valuation. It proposes that a multi-stakeholder steering committee be established under the auspices of the SAIMM, to deliberate and design a process for establishing such a Code.

Jan 1, 2002

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)–based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry, and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jul 7, 2023

By J. J. Pfeiffer, J. W. Myers, A. A. Orning

A study was made of the feasibility of using washery refuse in the manufacture of lightweight aggregate for building materials . Preliminary caking and burning tests showed that the refuse could be converted into lightweight aggregate but that refuse passing a No. 14 U.S. Standard screen could not be used without additional processing . The aggregate was prepared by pelletizing the refuse and burning out the carbonaceous material on a chain- grate in a refractory - lined furnace . A small stationary - grate furnace was used to study the process variables involved and establish optimum ignition and combustion conditions . Maximum ignition rates were obtained at air rates of approximately 200 lb per sq ft hr , but air rates of 450 or higher were required in the burnout period to obtain temperatures high enough to sinter the ash . The data obtained from this unit were used as a guide in the operation of the chain- grate furnace . In the chain - grate furnace , satisfactory results were obtained by using primary air rates of 200 lb per sq ft hr in the ignition zone and 500 lb per sq ft hr in the burnout zone . The ignition- zone air was preheated to 500 ° F , but the air for burnout was not preheated . A total of 2-1/2 tons of aggregate was prepared in this unit and made into experimental block . A commercial development based upon the results of this study yielded a product which met the ASTM specifications C 130-42 for lightweight aggregate , and blocks made from the aggregate were of good color , durable , and light - inweight .

Jan 1, 1964

By J. H. Hamilton, J. R. Lewis, J. H. Dismant, W. M. Fassell

RECENTLY this laboratory undertook the task of preparing some low carbon metallic cobalt by the carbon reduction of precipitated cobalt oxides. The oxides came in two lots and had the compositions given in Table I. Industrially, cobalt rondels' are made by the carbon reduction of cobalt oxide in small reverberatory furnaces at temperatures near but not above 1050 °C. This is a slow and tedious small batch process but does give cobalt metal which is low in carbon (1 pct C). Inasmuch as these cobalt oxides were relatively low in copper and iron it was decided to reduce them with petroleum carbon in a small three-phase electric arc furnace of about 3 to 5 Ib of metal capacity. It was hoped such a procedure would save considerable time and perhaps also indicate an improved commercially feasible process. The furnace was preheated by using small pieces of carbon electrodes to maintain the arc until a temperature of 1500°C was reached. The broken pieces of electrodes were then removed and 500 g of the cobalt oxides and 60 to 100 g of petroleum coke added. At the end of the reduction reaction, a high lime flux was added to the furnace to facilitate the removal of sulphur. Due to the fineness of the cobalt oxide powder used and also to the presence of chlorides there was considerable dust lost in charging the furnace. This was overcome by preparing briquettes composed of the cobalt oxides, charcoal, and a little bentonite to serve as a binder. The results obtained are summarized in Table 11, which shows that the cobalt metal produced in the arc furnace was high in carbon varying from 2.5 to 3.5 pct. This, of course, is much too high. For certain uses, such as in the preparation of permanent magnets, the carbon content of cobalt must be low. It was necessary therefore to find an effective method of reducing the carbon content of the cobalt that had been prepared in the arc furnace. Van Arkel3 recommends the use of Co2O3 as a means of removing carbon from cobalt. Experiments by the authors indicate that carbon is removed with difficulty by this method. Other methods used, including lancing of the molten high carbon cobalt with a jet of oxygen, proved to be ineffective. The method finally used makes use of the fact that cobalt metal is decarburized by carbon dioxide at the temperature of the molten metal. Two methods were used: 1—carbon dioxide was bubbled up through the molten cobalt, and 2— molten cobalt was maintained in a carbon dioxide atmosphere. In the first method the gas was introduced below the surface of the molten metal by means of a quartz tube. A high frequency induction furnace was used to keep the cobalt molten in both of these experiments. This kept the metal somewhat agitated and no doubt was an important factor in hastening the decarburization 'process by the second method. Both methods gave satisfactory results as shown in Table 111. An interesting observation in connection with this 'work was that a small sample of carburized cobalt metal could be decarburized by heating it with an acetylene torch adjusted to give an oxidizing flame. This may have been due to the presence of carbon dioxide in the products of combustion. Samples of molten high carbon steel were decarburized by the same method and it is suggested that nickel and perhaps manganese can be decarburized in a similar manner. Additional work, including rate studies and other theoretical aspects of this problem, is in progress in this laboratory.

Jan 1, 1953

By Zhongran Dai, Nan Hu, Jianhong Ma, Hui Zhang, Zhihua Zhong, Han Zhou, Feng Li, Yonggen Qiu, Yang Ding, Yingchun Yang, Dexin Ding

In the traditional chlorination roasting-water leaching-solvent extraction process for the extraction of rubidium-bearing ore, Rb leaching from the ore and calcium removing from the leachate are conducted separately, and this results in the complicated process and high energy consumption. In order to integrate the Rb leaching and calcium removing processes, Rb-bearing polymetallic ore was firstly treated by chlorination roasting, it was then leached in a micro-reactor with raffinate, and the calcium ions in the leachate were removed in the reactor as carbonate precipitates by passing CO2 at certain pressure into the reactor. The effects of raffinate alkalinity, CO2 pressure, and CO2 reaction time on Rb leaching rate and calcium removing rate were investigated. The experimental results show that when Rb-bearing polymetallic ore was leached for 90 min by stirring with raffinate with 1.125-mol/L alkalinity, and the pulp was made to react with CO2 at 0.8 MPa for 15 min, the Rb leaching rate and calcium removing rate amounted to 92% and 98.2%, respectively. This integrated process including Rb leaching from Rb-bearing polymetallic ore and calcium removing from leachate could simplify the process for the extraction of Rb-bearing ore and increase its economic benefits.

Sep 27, 2023

By J. B. F. Champlin

The continuing development of the nuclear industry in the United States requires a program of waste disposal that insures against the release of large amounts of radioactivity to the environment. This paper describes research on one proposed means of disposal of this waste, that of injection into geologic formations at depth. Nuclear production plant wastes were simulated and injected into samples of sedimentary rock obtained from outcrops, quarries, and deep wells. Changes in the chemical and physical characteristics of the rocks caused by the interaction of ions and suspended particles in the waste solutions with the cementing material and claylike particles in the rock are discussed. Laboratory tests show that nuclear wastes can be injected into many natural porous, permeable geologic formations. Injectivity can be maintained over a longer period by monitoring the ionic balance and particle-size distribution of waste streams. The combination of permeability and porosity with low cation-retention capacity, as exhibited by most sandstones, would satisfy the engineering requirements for the subsurface disposal of nuclear waste. Shales and clays with their low permeability and high cation-retention capacity would make excellent confining formations. The amount of cation retained by sedimentary rocks increases with increasing valence or concentration of the cation or decreasing brine concentration. The use of rock cores as model reservoirs had proved successful in determining some of the parameters that need to be considered in full-scale field disposal of wastes.

Jan 1, 1967

By M. L. Fuller

IN connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segre-gate structures of the Widmanstätten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith1 the plane of segregation in the matrix con-tains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the literature.2 The increasing com-mercial importance of zinc alloys containing copper makes this funda-mental study of value to the metallography of zinc alloys.

Jan 1, 1933

By G. X. Zeng

A calculation programme of finite element method has been developed in order to study the behavior of excavation with sheet piling in soft clay. Based on a series of isotropically consolidated-undrained tests (CIU) on Hangzhou clay a linear relationship between the normalized initial tangent modulus number, E1, and stress-path parameter, a, is found for four different stress paths, and stress-path dependent modulus equations derived. Meanwhile, several influence factors, such as embedment depth and stiffness of the wall and soil conditions, were taken into consideration in the programme. Some valuable conclusions were obtained. Finally, a case history was studied by the proposed method of calculation. The result of calculation and the field observation are in good agreement.

Jan 1, 2010

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By P. Lafleur

All indications point to a growing market for thermal coal in Japan as part of the country's current energy policy formulation process. The Ministry of International Trade and Industry forecasts imports of 16 million tons a year in 1985 and 40 million tons in 1990-a twenty-fold and forty-fold increase over the present level. This potential reflects Japan's over-all serious and increasing concern for security of energy supplies and its resultant need to seek alternative sources. Nuclear power will be the main alternative source, but, because it is expected that its development will be slow, imported thermal coal will assume greater importance. Canada, with large resources of all types of coal, could fill a portion of this market. Thermal coal could come from specific thermal coal developments or from metallurgical coal mines, which usually produce a certain amount of coal not amenable to coking, but suitable for power purposes. However, penetration of this Japanese market by Canadian thermal coal will depend on the resolution of a number of problems. On the demand side, siting, environmental aspects, the need for a coal unloading and trans-shipment centre, and the added cost of installing coal-fired stations could be major constraints. Although Canada has ample high-quality resources, any new development tied to the Japanese market will require improvement in prices to cover the high costs associated with transportation, the construction of new mines and the provision of new infrastructure.

Jan 1, 1979

By L Q. Amorim

The mining district of the Quadrilátero Ferrífero (QF) in southeastern Brazil contributes to 70 per cent of the Brazilian iron ore production, which reached 370 Mt in 2010. Traditionally, four iron ore types were mined in the QF region:1. soft haematite,2. hard haematite,3. friable ‘itabirite’ (the Brazilian name for metamorphosed banded iron formation), and4. canga (an indurated iron-rich crust).With the exception of the hard haematite, these categories derive from supergene enrichment of the Paleoproterozoic Cauê Itabirite. High current iron ore demand means that the QF high grade supergene ores will be depleted in a few decades. Consequently, several mining projects are being developed to exploit unenriched, fresh itabirite. Among them, the Mineração Usiminas Serra Azul project in northwestern QF is one of the most advanced. Four major itabirite types occur in the QF region:1. siliceous (or standard),2. dolomitic,3. amphibolitic, and4. magnetitic.The dominant type in Serra Azul region is a fresh siliceous itabirite, composed essentially of haematite, martite and quartz that averages 36 per cent Fe (51.5 per cent Fe2O3) and 47 per cent SiO2. The second type, the magnetitic itabirite, consisting of magnetite, martite, gruneritecummingtonite, quartz, dolomite, stilpnomelane, and subordinate haematite, is typically a strongly magnetic greenish banded iron formation with the iron grade varying between 25 and 35 per cent. Chemically, it differs from the siliceous itabirite due to the relatively high CaO, MgO and, consequently, high LOI contents. Together with supergene ores, fresh itabirites have been included in the ore reserves of the Serra Azul project. We anticipate that all the four types of fresh itabirite will be incorporated as ore in the QF region, causing a huge increase on the iron ore resources of the district, and representing enormous environmental and technological challenges for the local iron ore industry.

Jul 11, 2011

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By Robert B. Worthington

This investigation was undertaken to develop a more efficient copper smelting practice that would help meet the increasingly stringent antipollution standards. Continuous smelting to copper and a 0.8-to 5-percent copper slag using pure oxygen has been demonstrated for several hours at a time in a unique double furnace, which was devised to overcome the heat losses inherent in a laboratory furnace. The use of pure oxygen to effect the smelting and conversion of copper sulfide concentrate in a single unit to produce blister copper and a very high S02 concentration provides a much reduced gas volume for more economical and thorough sulfur recovery. Although the process was successfully demonstrated for several hours at a time, extended test work using longer runs will be required to balance the system and to obtain test data for adequately demonstrating its technical feasibility.

Jan 1, 1973