Search Documents

By E. Mille, R. Geffken

The Mg-Si and Mg-Ge phase diagrams were rede-levtnined by thermal analysis, and the existence of a single congruent melting compound in each system was confirmed. The melting points of the two compounds Mg2Ge and ,Wg2Si were found to be 1117.4° and 1085.0°C respectively. The euteclics for the Mg-Ge system occur at 635.6°C (1.15 at. pcl Ge) and 696. 7°C (64.3 at. pct Ge); for the Mg-Si system the eutectics are at 6376°C (1.16 at. pct Si) and 945.6°C (53.0 al. pcl Si). The phase diagrams and known thermodynamic data were used to calculate activity values for both systems. The activities calculated for the Mg-Ge system agreed very well with those previously published. Partial molar enthalpy values for the Mg-Si systetn were calculated from the phase diagram for the composition region where no experimental values have been reported. THE phase diagram for any system is an important source of thermodynamic data. Steiner, Miller, and Komarek1 have derived equations which permit calculation of the activity in binary systems with an inter-metallic compound! if the liquidus and enthalpy data are known. The thermodynamic properties of the Mg-Ge and Mg-Si systems have recently been determined in this by by an isopiestic method, and it was considered that it would be interesting to compare these directly determined values with those computed from the phase diagram. The basic features of the Mg-Ge and Mg-Si systems are essentially similar. The one intermediate compound present in each system. Mg2X, crystallizes in the antifluorite structure and melts congruently. Raynor4 has accurately determined the temperature and composition of the magnesium-rich eutectic in both the Mg-Ge and Mg-Si systems. Klemm and West-linning5 investigated the entire Mg-Ge liquidus, employing sintered alumina crucibles; the purity of the magnesium and germanium starting materials was not reported. The melt was not stirred, and the temperature was automatically recorded to an accuracy of ±3°C. The authors reported large weight changes due to magnesium evaporation between 50 and 67 at. pct Mg. The Mg-Si system has been studied by a number of investigators, and the results have been compiled by Hansen and Anderko.6 Significant discrepancies exist between the two principle investigations of voge17 and Wohler and Schliephake.8 Two different grades of silicon were used by Vogel, one of 99.2 pct purity and the other quite impure, containing 6 pct Fe and 1.7 pct Al. The magnesium purity was not specified. The melts were contained in graphite crucibles with porcelain thermocouple protection tubes under an atmosphere of hydrogen. Samples weighing 10 g were rapidly heated to 50° to 100°C above the liquidus: held, and then rapidly cooled without stirring. Accuracy was ±1 at. pct which is equivalent to a maximum error in temperature of ±18°C. Wohler and Schliephake used 97.9 pct Mg and 99.48 pct Si. The graphite crucibles contained a stirrer and the 15-g samples were melted under an atmosphere of streaming hydrogen. The samples were chemically analyzed after each run. Because of the scarcity of the data, the impurity of the starting materials, and the resultant uncertainty and inconsistency in the published liquidus values, it was decided to undertake a reevaluation of the Mg-Ge and Mg-Si phase diagrams by thermal analysis. EXPERIMENTAL PROCEDURE Alloys were prepared from 99.99+ pct Mg (Dominion Magnesium Ltd.) with impurities in ppm: 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu. <10 Fe; 99.999 pct Ge (United Mineral and Chemical Corp.), and 99.999 pct Si (Wacker Chemie Corp.). All graphite parts were machined from high-density (1.89 g per cu cm) G-grade graphite obtained from Basic Carbon Corp. with a total ash content of 0.04 pct. Boron nitride parts were machined from rods of National-grade H.B.N. boron nitride. All graphite and boron nitride pieces were baked out under running vacuum at 1100°C for 24 hr before us Cylindrical graphite crucibles (1; in. OD, 23/4 in. long, l3/8 in. ID) were tightly closed with threaded graphite covers which had 21/4-in.-long thermocouple wells and 1/4-in.-diam off-center holes for stirrers. The cover and thermocouple well were machined from a single piece of graphite. A stirrer was made from a flat cylindrical graphite plate perforated with five 3/16-in.-diam holes and a 1/2-in.-diam central hole, and was held parallel to the crucible bottom by a 1/4-in.-diam. 4-in.-long graphite rod which screwed into the plate and extended up through a tightly fitting hole in the crucible cover. An iron core enclosed in a glass capsule was attached to the stirrer with an 18-in.-long molybdenum wire, so that the stirrer could be magnetically raised and lowered from outside the system. One crucible and stirrer with essentially the same dimensions given above was made entirely of boron nitride. Chunks of magnesium were premelted, cast into 11/2-in.-diam. rods, and then cut into lengths varying from a to 1 in. A 5/16-in. hole was drilled through the center of each piece to accommodate the thermocouple well and the individual pieces were then cleaned and rinsed with acetone. The total weight of an alloy was 50 to 70 g in the Mg-Ge system and 40 to 60 g in the Mg-Si system. The pure components were weighed to an accuracy

Jan 1, 1969

By R. J. Pokora

This Bureau of Mines report is an applications manual that can be used by the nonmetallic mining industry for guidance in installing noise control materials into crushing and screening plants. These noise control modifications were installed and successfully tested at three operating quarries. This report identifies the major noise sources that can be encountered in crushing and screening plants, and discusses the applicable noise control materials and techniques that a plant operator can utilize on a retrofit basis to reduce equipment noise.

Jan 1, 1984

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By Daniel C. McLean

Extraction data for Cu, Zn and Fe were obtained from 4.5" and 10" columns using massive sulfide ore and natural acid mine water. The purpose was to determine if recycling of solution through the column would produce leach liquors of 4 g/l Cu and Zn at extraction rates of 1 g/l per pass at typical flow rates of 0.002 to 0.006 gpm/sq.ft. Test results exceeded expectations. Cu and Zn concentrations of 4 g/l were obtrained within 4 to 6 cycles. Concentrations greater than 6 g/l Cu and 8 g/l Zn were reached within 10 cycles. Concentrations of greater than 40 g/l of Fe and free sulfuric acid were obtained with no decrease in biological activity being observed. No reagents were used.

Jan 1, 1995

By A. Hasko

Phytoremediation is a new low cost alternative technique for remediation of contaminated soils from heavy metals that are emitted by ferrous and nonferrous mining and extracting processes. It is based on the possibility to use several plants that accumulate high level of metals in order to remove metallic pollutants from soils and render them harmless. Phytoextraction is an adjacent new technique that uses these hyper-accumulator plants in order to extract the metals from them using even the conventional smelting or refming processes. In our previous work, an extensive investigation of about 150 plants have been carried and several species were identified that could be used for nickel phytoremediation and phytoextraction because of their high accumulation of nickel. It has been found that five taxa from Alyssum genus specie had the highest ability to accumulate nickel with concentrations more than 10000 ug/g (dry weight) or 1%. The taxa showing the highest accumulation of this metal is Alyssum murale var. chlorocarpum with 28 600 ug/g or 2.86%, a good candidate for Phytoextraction. In this work, in order to optimize the phytoremediation and phytoextraction processes further Absorption Spectrometry measurements and biological studies were carried out to determine the parts of the plants that accumulate the highest amount of nickel and the best biological cycle during which they accumulate the highest amount. The results show that the greatest accumulation of nickel occurred in the leaf material (2.86%) and the least in the roots (0.43%). The investigation of the biological cycle of the genus Alyssum showed that: (1) the seeds germinated between 50 C to 30 0 C and more in 25 0 C; (2) 62.9 % of seeds germinated at A.m. var. chlorocarpum; (3) the emergence is almost continue from March to April; (4) the anthesis occurs from May to July; (5) the ripening of the fruit takes place 30 days after flowering; (6) the dissemination of fruits occurs from September to October. Due to these special characteristics it is reaffirmed that Alyssum murale var. chlorocarpum, as a nickel hyperaccumulator, is the most promising plant to be used for feasible phytoremedation and phytoextraction purposes. Keywords: Key words: Phytoextraction, PhytoRemediation, Nickel accumulators, Alyssum sp., Biological cycle

Jan 1, 2003

By Jeffrey P. Schubert

The study site in northeastern Illinois underwent surface mining for coal in 1943 and was reclaimed by the state of Illinois in 1972-1973. Additional soil amendments and seed were applied to the spoil surface in 1975-1980. Previous studies in 1975-1978 had shown that the surface spoil materials and five final-cut lakes at the site were quite acidic and the lakes contained high concentrations of sulfate and dissolved metals. Surface runoff water from monitoring plots in 1976 were only moderately acidic and the mean concentrations of most dissolved metals and sulfate in the runoff waters were less than 25% of the concentrations found in Lake B. By 1980, vegetation had become well established over most of the mined area. However, the five final-cut lakes (Lakes A-E) remained acidic. The purpose of the study reported here was to determine the physical and geochemical subsurface conditions of the spoil materials, the hydrologic flow system within the spoils, and the magnitude of acidic spoil leachate migration into the lakes and into the wetland prairie north of the mine site. Lakes A, B, C, and E were still very acidic in 1980-1981 (pH range: 2.9-3.4; aridity range: 110-860 mg/L as CaCO3). Lake B had the worst water quality, with mean concentrations of dissolved aluminum, iron, manganese, and sulfate of 75, 25, 37, and 3340 mg/L, respectively. Shallow groundwaters in spoil materials around Lake B had a lower pH and about two to four times greater concentrations of aridity, aluminum, manganese, zinc, and other metals and nearly 20 times greater dissolved iron than the water in Lake B. The shallow groundwaters in undisturbed soils and bedrock 10-30 m north of the mine site spoils generally were alkaline, but did contain occasional moderately high sulfate and metal concentrations. Pumping tests and recovery tests conducted in piezometers showed hydraulic conductivities of spoil materials ranging from less than 10- to 10-5 m/s; hydraulic conductivities of natural soils and bedrock were measured between 10-10 to 10-7 m/s. Water levels in spoil materials increased rapidly in response to rainstorm events and the recession curves were relatively quick to decline, lasting only two or three days. Quick infiltration of rainfall into the spoil surface and percolation down to the water table caused a rise in groundwater levels and movement of spoil groundwater into the lakes. This groundwater component in the lake water budgets could account for most of the water quality problems occurring in the acid lakes.

Jan 1, 1984

By Gian Carlo Ticona

El presente estudio plantea una metodología para realizar el criterio de caracterización geomecánica de macizos rocoso alterados, empleando información geomecánica de la franja metalogenética de Andahuaylas – Yauri, este sector es importante para la industria minera en el Perú, actualmente cuenta con el desarrollo de grandes operaciones mineras y tiene una buena perspectiva para el desarrollo de futuros proyectos mineros. En el cinturón de Andahuaylas – Yauri se tiene yacimientos mineros del tipo pórfido – skarn de Cu, Ag y Au principalmente

Sep 30, 2022

By John C. Edwards

A fire location computational model was developed by the U.S. Bureau of Mines. The model can determine all the possible paths in a mine that smoke can travel from a fixed fire source to a smoke detector. The associated FORTRAN computer program can be utilized to determine the minimum travel time from a source fire to a smoke detector. The difference in travel time from an isolated fire source to two or more detectors can be used to isolate those airways in which the source fire is located.

Jan 1, 1990

By J. H. Westbrook, R. W. Guard

The influence of a number of alloying additions on the structure and hardness of Ni3Al (?&apos;) has been studied. Three general effects have been observed.. solid-solution hardening, strain aging, and defect hardening arising from deviations from stoichiometry. The solid-solution hardening phenomena are complicated relative to binary terminal solid solutions due to the possibility of virtually independent substitution for the component elements and to the concomitant effects of strain aging. In many superior nickel-base high-temperature alloys the elevated temperature strength is attributable to the presence of a dispersion of Ni3A1 (?&apos;) in a solid-solution matrix. Examples of such alloys are Inconel X-550, Inco 713, Waspalloy, and Nimonic 80. It is, therefore, appropriate to seek a further understanding of the properties and alloying behavior of this compound. Ni3Al, the compound most rich in nickel in the nickel-aluminum binary system, was first detected by litakal but not established with certainty until the much later studies of Bradley and Taylor&apos; and Alexander and Vaughan.3 More recently the mechanism of formation was clarified by Floyd4 who showed that Ni3Al is the product of a peritectic reaction at 1395°C between the melt and the compound NiAl in agreement with the original suggestion of Alexander and Vaughan.3 Ni3Al has the ordered face-centered-cubic or Cu3Au structure in which the nickel atoms occupy the face centers and the aluminum atoms the cube corners, a0 = 3.570A. Despite earlier reports to the contrary. the compound apparently remains ordered at least to 1000oC.5 It exists over a narrow range of compositions (-3 pct wide) whose limits and temperature dependencies thereof have been reviewed recently by Taylor and Floyd.&apos; Most previous workers have found Ni3Al to be both hard and brittle7,8 although Maxwell and Grala8 obtained 2.5 to 6 pct tensile elongation at room temperature and Alexander and vaughan3 described the material as "hard and tough" on the basis of observations made while preparing metallographic specimens. In a recent study one of the present authors found that although considerable intergranu-lar brittleness was evident: individual grains of a coarse-grained inert atmosphere arc-melted specimen were readily deformable.l0 The same study also showed Ni3Al to have an anomalous temperature dependence of hardness in that such a curve exhibits a number of peaks between room temperature and 800°C which could not be associated with any microscopically observable precipitation reactions or polymorphic transformations. It was, therefore, proposed in the present study to elucidate the anomalous high-temperature strength behavior and to examine the solid-solution alloying of this compound and the effects of such alloying on hardness. Sample Preparation and Experimental Procedure-Samples, both of pure Ni,Al and of various alloyed solid solutions based on Ni3Al, were prepared by arc melting 100-g buttons in an inert atmosphere arc furnace. All buttons were heat treated for 4 hr at 1275oC and examined metallographically for homogeneity. Microstructures were typically homogeneous and single phase with ASTM grain size about 1 and unusually clean grain boundaries. Chemical analyses showed good correspondence (within a few tenths of a percent) with intended compositions. Microindentation hardness data were obtained from room temperature to 800°C in vacuo using a balanced-beam type loading system in an instrument to be described in detail elsewhere." In general a 100-g load, a loading rate of 1 mm per min and an indentation time of 15 sec were used. Various indenter materials were used according to the materials bein tested because of specimen-indenter interaction. Fl Measurements of the Vickers-type indentations were made at room temperature. Hardness-temperature curves were run at least twice on each sample to ensure that surface work-hardening effects had been eliminated." Precision lattice-parameter measurements were made on powder samples using a back-reflection

Jan 1, 1960

CONTENTS PAGE ANDERSON, ROBERT J., and ENOS, GEORGE M.-Corrosion of Brass as Affected by Grain Size. Discussed by Henry S. Rawdon, Robert J. Anderson, Francis B. Coyle, William B. Price, and W. R. Webster 1 RAWDON, HENRYS., and MUTCHLER, WILLARD H.-Effect of Severe Cold Working on Scratch and Brinell Hardness. Discussed by W. H. Bassett, John Livermore Christie, John R. Freeman, Jr., W. R. Webster, William B. Price, Norman B. Pilling, D. J. McAdam, Jr., F. G. Smith, Zay Jeffries, F. E. Carter 3 WILLIAMS, ROBERT S., and HOMERBERG, VICTOR 0.-Relation of Heat Treatment to the Microstructure of 60-40 Brass. Discussed by 0. W. Ellis 14 Corrosion of Brass as Affected by Grain Size Discussion of the paper of ROBERT J. ANDERSON and GEORGE M. ENOS, presented at the New York Meeting, February, 1924, and issued as Paper No. 1282, with MINING AND METALLURGY, December, 1923. HENRY S. RAWDON,* Washington, D. C. (written discussion).-So numerous and so varied are the factors that affect the corrosion of metals that particular care is necessary in corrosion tests to eliminate so far as possible all extraneous factors. It appears to the writer that the question may well be asked as to whether all the necessary precautions have been observed in this investigation. It may be that the points to be mentioned were considered by the authors and found to be insignificant; however, there is nothing in the report to show this.

Jan 5, 1924

By Ye Chen, Jianhua Chen, Meng Liu, Yuqiong Li, Xiao Mu, Cuihua Zhao

"Sulfidization-amine is the most effective method for the recovery of smithsonite (ZnCO3), however the interface interaction details remain unclear. The sulfidization-amine flotation mechanism of smithsonite has been studied by Density Functional based Tight Binding (DFTB+) method in this paper. The slab model of ZnCO3 (101) surface was built and the adsorptions of a monolayer of HS- and S2- ions were conducted to model the sulfidization effect on the ZnCO3 (101) surface adsorption. DDA hardly interacts with the hydrated ZnCO3 (101) surface. Under the low concentration of Na2S, HS- ions form a Zn-SH-SH structure on the ZnCO3 (101) surface, which hinders the interaction between DDA and surface Zn atoms. Under the high concentration of Na2S, a layer of ZnS is formed on ZnCO3 (101) surface, which is favorable for the adsorption of DDA on the surface. This is consistent with the flotation practice where smithsonite flotation requires a large amount of sodium sulfide. The results could provide a microscopic investigation into the sulfidization-amine flotation mechanism of smithsonite.INTRODUCTIONSmithsonite (ZnCO3) is an important and typical oxide mineral of zinc. It is a semi-soluble salt mineral with a solubility product constant of 1.46 × 10-10 (Weast, 1973). The most common and effective method to recover oxidized zinc ores is froth flotation (Caproni et al., 1979; Pereia and Peres, 2005; Kashani and Rashchi, 2008). It is well known that the flotation of oxidized zinc minerals is much more difficult than the flotation of zinc sulphide minerals (Hosseini and Forssberg, 2007).The recovery of zinc oxide ores with poor floatability attracts more and more attention due to the depletion of easy-recovered of zinc sulfide ores.Sulfidization-amine flotation, which using Na2S as sufidizing agent and amine as collector (Mckenna et al., 1949; Rey, 1954; Abramov, 1961; Rey, 1979; Hosseini and Forssberg, 2007). This method is the most successful technology used for zinc oxide minerals flotation in large-scale industrial applications since it was invented in the 1950s (Önal et al., 2005; Pereira and Peres, 2005). There have been numerous experimental researches on the sulfidization-amine flotation of smithsonite. Shi et al., (2013) studied solution chemistry of smithsonite flotation system. Feng and Wen (2017) studied the formation of zinc sulfide species on smithsonite surfaces and its response to flotation performance. Wu et al., (2017) investigated the sulfidization behavior of smithsonite with the use of zeta potential, inductively coupled plasma (ICP), scanning electron microscope (SEM), and X-ray photoelectron spectroscopic (XPS). Their measurement results confirms the chemisorption of sulfur ions and the formation of ZnS film on the smithsonite surface after Na2S treatment, however the influence of HS- ions on the surface and the influence of sulfidization on the amine adsorption have not been discussed."

Jan 1, 2018

By D. Scott Scovira, Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance.

Jan 1, 2010

By Jorge Meza

Uno de los objetivos principales del proyecto de la modernización de la Fundición SPCC es capturar y procesar el gas generado de la reacción exotérmica del proceso de fusión de los sulfuros del concentrado para transformarlo en un subproducto comercial que es el (ácido sulfúrico) H2SO4. En ese sentido, el presente texto señala el manejo de un sistema de control de gases a través de un proceso sofisticado para el enfriamiento, limpieza y manejo de este gas de dióxido de azufre, reduciendo los costos de operación, así como el tiempo de reacción de los equipos involucrados en el manejo y procesamiento de los gases.

Sep 19, 2006

By T. H. Patching

This paper provides a review of the available information on the origin and mechanisms of the release of gas from coal seams. With the opening up of new mines in Western Canada and the increased mechanization of underground coal mines, the study of gas emissions is of increasing importance in providing safe working places underground.

Jan 1, 1970

By Duah Philip, Awuah-Offei Kwame

Regulatory pressure to mitigate the cement industry’s environmental impact has intensified recently, spurring innovation in low-carbon cement technologies. In the United States, cement production, consumption, and carbon emissions are accelerating. Despite this trend, the adoption of environmentally friendly dry clinker production technology with combined preheater-precalciner systems has surged from 53.3% in 2002 to 88.5% in 2019. Concurrently, reliance on wet technologies, known for their higher environmental impact, has dropped from 16.5% to 0.6% within the same period. This paper presents the results of our comprehensive study, utilizing over 100 years of industry data, to analyze these technological shifts and their environmental implications.

Feb 1, 2025

By R. E. Mclvor

This is an update of an original dissertation on this topic by Lavallee, McIvor and Stolovitch (1992). A step-by-step, technical procedure used to measure and improve the performance of plant grinding circuits was adapted into a training program. ?Systematic Design of Instruction? was applied to: ? Determine if training was a suitable way to deliver this new technology; ? Define the technical content of the program; ? Select program specifications based on learner and context characteristics; ? Design, create and test prototypes of the training modules; and, ? Establish a process for plant implementation. The training program covers numerous skills that are extremely valuable for plant personnel, not only in the grinding area, but also for many other parts of the plant. This paper describes how new skills are brought into the workplace through designed instruction can be an effective alternative to hiring during severe skilled labor shortages.

Jan 1, 2008

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By C. R. S. Needes, M. J. Nicol, G. T. W. Ormrod, N. P. Finkelstein

The industrial application of a dioxide electrode uranium by C. R. S. NEEDES, Ph.D. (London) (Visitor), M. J. NICOL, Ph.D. (Rand) (Visitor), N. P. FINKELSTEIN M.Sc. (Rhodes), Ph.D. (Liverpool) (Fellow), and G. T. W. ORMROD (Visitor) A correlation between the potential of a U02 electrode and the rate of recovery of uranium has been proved in laboratory and plant trials. When the recovery rates change because of variation in the concentrations of Fe(III), Fe(II), SO4 &apos;and H+, a positive correlation is observed. However, an 2- increase in the concentration of phosphate in solution produces an increase in the U02 electrode potential but a decrease in the rate of leaching of U02. The correlation between the U02 electrode potential and the rate of leaching of U02 is then negative. It is concluded that, as a control device, the electrode cannot compete with the platinum electrode for use on certain plants. Nevertheless, the U02 electrode will act as a useful warning device if the total concentration of iron in solution decreases to below a level concomitant with the economic recovery of uranium. Furthermore, because of the positive correlation between the U02 electrode potential and the phosphte concentration, the electrode will also be of value in the detection of an increase in the phosphate level in solution. When it was incorporated in a suitable industrial probe, the electrode was found to be able to withstand the rigours of the leaching conditions in a large pilot-plant pachuca, and only failed after six weeks&apos; operation.

Jan 11, 1975

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010

By E. Özberk

Uranium minerals are often associated with iron minerals, and during the hydrometallurgical processing of the uranium ores, iron plays several significant roles. The presence of Fe(III) in solution promotes the oxidative acid leaching for the recovery of uranium. The control of the distribution of impurities in milling and refining is also affected by dissolved iron. When rejected from the process streams, iron usually collects other impurities and contributes to the stabilization of the wastes for final disposal. These roles of iron, as they relate to current uranium processing operations, are discussed in detail, and some broad and historical perspectives are also presented.

Jan 1, 2006