Search Documents

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests. Each ore is an individual problem until the association of the gold has been determined. Knowing the problem through the interfering minerals or elements, the solution often is only the application of part of a former known practice as an auxiliary or additional feature. In the treatment plan for most gold ores, it has been the custom to try each of the usual recovery methods or combinations thereof, accepting the best results on a basis of the lowest cost. A better plan includes knowledge of the association of the gold and the various minerals from which it is to be recovered. This presents reasonable foresight into the problems that should be expected and permits some provision for avoiding probable difficulties. The preliminary work should include: Determination of the percentage of free gold with classification showing size of gold particles to be expected; determination of the percentage of gold associated with each mineral and whether it be freed from the mineral by crushing; and an analysis of representative samples of the ore to include other valuable minerals and the form in which they occur.

Jan 1, 1934

By Bertrand L. Johnson

Before 1914 , Chile , because of her extensive resources of natural nitrates , practically monopolized the world markets for one of the leading fertilizer materials . Since nitrogen also is an important war material , constituting in fact the principal ingredient in many high-powered explosives , the World War and the widespread insistence upon national self- sufficiency for war materials brought about the development of nitrogen fixation plants in all of the larger countries . The production of by- product ammonia from gas and coke plants was likewise stimulated . As a result , Chile , even after the ocean lanes were reopened , was forced to fight for her lost markets . Since the world capacity to produce is still far in excess of annual consumption , the competition between natural and synthetic supplies has been keen and prices have fallen below pre-war levels . Chile has recently succeeded in unifying her industry , utilizing the most efficient process now in operation, and the Government is a partner in the new company that will take over all of the present producing companies . These developments place Chilean nitrate of soda , in a much more favorable position among the markets of the world . More intense competition will undoubtedly follow and , in order that those interested may become familiar with the fields upon which the nitrogen conflicts of the near future may be waged , the following general summary of the nitrogen industry has been prepared .

Jan 1, 1931

By W. C. Blanchard

Time Domain Reflectometry (TDR) is a remote sensing technique using active backscatter. This technique is applicable to the testing for faults and multiple partial faults on cable. The battery operated hardware developed on this con¬tract has tailored this technique for testing of mining equipment trailing electrical cables. The processing of-t-he back-scatter is accomplished using a microprocessor. The visual output from the hardware to the operator is; the type, magnitude and distance to the cable fault in a numerical format. This greatly simplifys the use of this techniques for the operator.

Jan 1, 1980

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

In 1962 and 1963, two in situ combustion pilot tests were conducted in the shallow Second Venango sand near Reno, Pa. Because of poor oxygen utilization and lack of production response, both tests were considered failures and were terminated. The area was then relatively inactive until late 1966, when a development well drilled near the 1963 test site had surprisingly good production in what was considered to be a pressure-depleted reservoir. Other wells drilled in and around the old thermal pilot areas also came in as good oil producers. This report presents a study of the increased oil production from the Second Venango sand in the Reno area, and the apparent connection of the present production response and the old thermal pilot tests. Apparently combustion occurred in the Second Venango sand after the 1962 and 1963 experiments were terminated and, supported by large volumes of air left in the reservoir after the 1963 test, generated carbon dioxide which helped repressure the formation. This field evidence of combustion warrants another pilot experiment to further explore the use of properly designed in situ combustion techniques in increasing production from the Second Venango sand.

Jan 1, 1971

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young&apos;s, shear, and bulk moduli and Poisson&apos;s ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By Jack J. Ayotte, Michael R. Nadon

"Today&apos;s demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco&apos;s Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine&apos;s 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco&apos;s Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By C. M. Lesher, R. R. Keays

"The komatnte-associated Fe-Ni-Cu sulphide mineralization at Kanihalda, Western Australia, is generally believed to be magmatic in origin, but a number of postmagmatic processes significantly modified the original distribution, structure, texture, mineralogy and chemistry of the ores. Two important types of mobilized magmatic sulphides are interpillow/interbreccia sulphides and hydrothermal vein-type sulphides. Interpillow and interbreccia sulphides occur interstitial to pillowed or volcaniclastic footwall metabasalts beneath or adjacent to the stratiform contact ore horizons. They are mineralogically and compositionally similar to massive ores (and are similarly depleted in PGE relative to the compositions of bulk samples of mined ores), but normally do not contain the distinctive chalco-phile ferrochromites characteristic of contact ores. They are interpreted as magmatic sulphides that have been mobilized from the overlying or adjacent massive sulphide layer during peak tectono-nietamorphism.Hydrothermal sulphide-quartz + albite veins also occur in the footwall metabasalt and contain unannealed deformation fabrics indicative of emplacement during retrograde metamorphism. The high Ni and Pd contents of these sulphides (7-13% Ni, up to 70 ppm Pd) indicate that the metals have been derived from the spatially associated komatiites and/or contact ores, consistent with the Pd depletion previously inferred for massive ores. Very low Ir contents and high Pd/Ir ratios of the vein-type sulphides confirm an aqueous transportation-deposition mechanism; hydrothermal transfer of PGE results in strong decoupling of Pd from Ir.There appears to be a complete continuum of sulphide mobilization at Kambalda ranging from whole-scale phy sical dislocation (fault offset ores) and selective mobilization (stringer sulphides) through nietamorphie replacement (interpillow/interbrec- cia sulphides) to jiydrothermal dissolution and redeposition (vein-type sulphides)."

Jan 1, 1984

By R. L. Xu

In this paper, the author would like to point out with figures that the building industry is one of the key industrial sectors of the national economy in China. And in the coming 15 years, the output of building construction will not in the least decrease, but increase. The requirements for building standards, quality, functions as well as physical environment will also be higher along with the incessant development of the national economy and the gradual raising of people&apos;s living standard. China is a country with a vast territory and a great, variety of physical characteristics. The topographic and engineering geotechnical conditions are complex and varies considerably from place to place. Although, in recent years, encouraging progress has been made in building construction, there still exist many problems unsolved or even not explored at all, which we have to tackle in the future design and construction of foundations. Also reviewed in this paper are the achievements attained in the past thirty odd years and the challenge we will face in the foundation engineering field in China.

Jan 1, 2010

By M. R. Hosseini

Among all gravity concentration methods, Shaking-table is the most effective one from the metallurgical point of view. In this study, Shaking-table was used for concentrating a manganese ore sample from Ghasem Abad area in Kerman, Iran. Experiments were designed by using L8Taguchi design with five variables and each variable in two levels. The influence of each variable and their interactions on the operation of the device was studied. The variables under investigation were: table slope, table frequency, water flowrate, feed rate, and particle size. The manganese concentrate grade and recovery were used as response variables. It was shown that water flowrate, table slope, feed rate, and particle size are the significant variable on concentrate grade; while, all the variables influence manganese recovery.

Jan 1, 2014

By William L. Crentz

This study of the preparation characteristics of the coals in Indiana County, Pa., is the second in a series of Bureau publications appraising the Nation&apos;s coking-coal reserves by counties and the practicability of upgrading marginal deposits to metallurgical standards. The first publication dealt with the preparation characteristics of the principal coal beds in Cambria County, Pa. Over 95 percent of the coal remaining in Indiana County is in the Upper Freeport, Lower Freeport, and Lower Kittanning beds. Isolated patches of Pittsburgh-bed coal are present, and the Upper Kittanning bed is found in minable thickness at some locations, but production from these sources is not large. The greatest production is from the Freeport beds, which account for nearly 70 percent of the Indiana County coal output. These beds usually contain two or more shale or hone partings and in many places are high in sulfur. The large proportion of bony coal in the Freeport beds &apos;produces a relatively high-ash product. Mining practices vary from place to place, but it is frequently necessary to leave certain bony portions of the bed in place in order to load a satisfactory product. Table 1 shows the county&apos;s coal production, by beds, during 1948.

Jan 1, 1951

By Wilson Bardales

El presente trabajo describe la experiencia de la Gestión de la Calidad en la Cía. Minera Poderosa S.A., específicamente en el rol que desempeñan los Círculos de Mejoramiento Continuo (CMC´s) como un vehículo efectivo para alcanzar los objetivos de la empresa. Los CMC´s están integrados por trabajadores de un mismo proceso, a quienes se capacita en el manejo de herramientas, técnicas y metodologías de la calidad, con la finalidad de realizar mejoras en los procesos. En ese sentido, en la compañía minera La Poderosa, la administración es participativa y el directorio difunde las políticas, para lograr la rentabilidad de la empresa. Así también, los mandos medios definen los objetivos y estrategias, desplegándola en cascada a la supervisión y estos a su vez, al personal de línea. Este concatenamiento de responsabilidades y la participación de los CMC´s aseguran el alineamiento y control de la gestión.

Sep 12, 2005

By S. Goto, S. Yamashita, K. Hata

"The average consumption of zinc dust for purification of zinc leaching solution is more than 25 kg per tonne of electrolytic zinc. Authors proposed to remove impurities in zinc leaching solution by electrolysis instead of cementation by zinc dust. The effects of copper and arsenic on electrodeposition of cobalt in zinc sulfate solution were examined fundamentally using a potentiostat. It is observed that cobalt is easily deposited on a cathode at potentials under -480mV with arsenic. Mesh cathodes of stainless steel and lead anodes were used in a small electrolytic cell and the electrolyte was circulated through 'the electrodes during the electrolysis. The effect of electrolyte circulating rate , pH, cell temperature, current density, and concentration of copper and arsenious ions on removal of cobalt were studied. Removal of Cd and Ni are also examined.IntroductionCobalt is difficult to remove from a zinc leaching solution by a simple cementation reaction using zinc dust. However, it is easily precipitated by zinc dust with co-addition of arsenious or stibinous oxide and copper ion in practical operations(I), (2), (3). The consumption of zinc dust for purification is 16-152 kg per tonne of electrolytic zinc and 65% of this zinc dust consumption is used for cobalt purification. The average retention time for purification of cobalt is 4.5 hours (1). A more economical process for purification is desired instead of zinc dust. The mechanism of this acceleration effect of copper and arsenious oxide on removal of cobalt are explained by the authorsas follows; a galvanic cell is formed between zinc dust and copper which is precipitated firstly, and cobalt is reduced on copper as Co-As alloy by this galvanic current(2). This assumption was confirmed in experiments using a galvanic cell with a membrane( 4). The following galvanic reactions occur between zinc dust and copper precipitate; on copper cathode,2H+ + 2e -= Hz(g)2Coz+ + 2HAs02 + 6H ++ 10e -= 2CoAs + 4HzOand on zinc anode,Zn = Zn = 2+ 2e –This galvanic current becomes almost zero in a zinc sulfate solution which includes only cobalt and no arsenious oxide, and cobalt is weakly deposited on a copper cathode. Cobalt deposition requiers a high degree of cathodic polarization. However, the galvanic current flows almost constantly in an electrolyte, which includes arsenious oxide, and the cathode potential is kept at about -500mV. Cobalt is precipitated as Co-As on the cathode.The authors assumed that cobalt may be removed by electrolysis at a very low current density instead of zinc dust and the following experiments were carried out. In the first part of this paper, the fundamental experiments using a potentiostat on the behaviour of cobalt in zinc sulfate solution are described. In the second part, the results of the electrolysis are reported. Cobalt is removed by a new type of an electrolytic cell, which was desigoed to <Iccelerate the rate of deposition of cobalt. The removal of cadmium and nickel in a solution which includes cobalt and arsenic are also examined."

Jan 1, 1997

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By A Esfahanipour, M Osanloo

Determination of cut-off grade?strategy is one of the most important stages of open pit mine planning and design. It is the parameter directly influencing the financial, technical, economic, legal, environmental, social and political issues in relation to mining operation. Choosing the optimum cut-off grade strategy that maximises the economic outcome has been a major topic of research workers for nearly one century. Many researchers have contributed in devising methods and algorithms, such as dynamic programming, linear programming, optimal control and so on for various aspects of its determination. In this paper, a non-linear mathematical programming for cut-off grade strategy optimisation is presented, considering the three main stages of mining operation introduced by K F Lane. In this model maximisation of net present value of mining operation, under the three constraints of mining stagesÆ capacities, considered as the optimisation criteria. Due to the discrete representation of the mining resource, the proposed non-linear formulation is approximated by a non-linear signomial geometric programming. According to non-convexity and the complexity of the proposed model, an augmented Lagrangian genetic algorithm was used to find the optimum cut-off grade strategy under varying and fixed price circumstances. To validate the proposed non-linear model efficiency, the results were compared with the results obtained by the K F Lane methodology. It was found that the proposed non-linear model works efficiently in the determination of cut-off grade strategy. According to the simplicity of the structure of non-linear programming modelling in comparison with dynamic programming it is hoped that, further development of this model would certainly provide the ability of considering managerial and technical flexibilities as well as incorporating more real mining conditions in the determination of cut-off grade strategy optimisation.

Sep 26, 2011

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992

By Natália Cristina Candian Lobato

A fim de se evitar os danos causados pela corrosão, cresce cada vez mais o uso do aço galvanizado. Durante o processo de galvanização a quente ou por eletrodeposição é gerado um resíduo sólido perigoso conhecido por lama galvânica cujo descarte se trata de um processo oneroso. Sendo assim, as principais rotas de gerenciamento desse resíduo foram levantadas no presente trabalho, visando contribuir com a economia e aumento da sustentabilidade desse setor industrial. Ultimamente a lama galvânica é considerada uma matéria-prima potencial por conter metais com valor comercial presentes em concentrações elevadas, e isso tem estimulado pesquisas de rotas de recuperação desses teores metálicos. Paralelamente, a fim de resolver o problema de gestão do resíduo, estudos buscam rotas alternativas de descarte que visem estabilizar os elementos tóxicos e reutilizar a lama como matéria-prima em outro processo industrial.

Aug 7, 2018