Search Documents

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By Gary Brendel

India produces about 70 Mt/a (77million stpy) of coal ash (fly ash and bottom ash) from burning about 200 Mt/a (220 million stpy) of coal for electric power generation. The average ash content is 35%. In contrast, the United States produces about 70 Mt/a (77 million stpy) of coal ash from burning 800 Mt/a (880million stpy) of coal for power generation. Its average ash content is less than 10%. In 1998, GAI Consultants Inc.(GAI) embarked on a federally funded, multiyear project to assist the government of India in solving its growing coal-ash management problem.

Jan 1, 1999

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Bill York-Feirn

The Colorado Mine Safety & Training Program (MSTP), in late 2005, completed and began distributing two new training tools; one geared to underground coal mine foremen and the other to surface aggregate employees. Through strong partnerships with MSHA, Colorado Coal Mine Board of Examiners, Colorado Mining Association and the Colorado Rock Products Association, the MSTP continues to create innovative and interactive training tools for not only Colorado, but for the national mining community. "Although we shoot and produce these materials in Colorado, it's important to us to make sure they are useful nationally," said Bill York-Feirn, MS TP Manager. The interactive DVD program "Underground Mine Foreman Certification Study Guide (Coal)," was completed in October 2005. It won the 2005 Grand Prize at the MSHA National Training Materials Competition in Beaver, West Virginia. [ ] This program is fully based upon the requirements of Title 30 Code of Federal Regulations (30 CFR) Parts 48, 50, 70 and 75 for underground coal mine foremen. It contains eight modules plus immediate access to relevant laws in the appendix. Topics covered include: Federal Law, Practical Math Skills, Mine Gases, Ventilation Maps, and scenarios addressing a variety of practical mining concerns. The DVD is designed for self-¬paced study and practice.

Jan 1, 2006

By Hanry Guillén

En la Compañía Minera KOLPA, se analizó el comportamiento de sus operaciones unitarias por el período Marzo - Agosto 2016, en el cual se identificaron procesos asociados a los ciclos de perforación y voladura, bajo los términos de variabilidad NO ESTABLES NI SOSTENIBLES, los mismos que ameritaban medirlos, analizarlos, mejorarlos y controlarlos a fin de adoptar decisiones que conduzcan a operar la mina en términos de calidad y excelencia.

Sep 1, 2017

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Vitor Falcão Artacho

As ligas de alta entropia são sistemas de ligas multicomponentes onde os elementos constituintes estão em proporções atômicas equivalentes ou quase equivalentes. As ligas de alta entropia são materiais avançados com propriedades únicas e promissores como materiais estruturais. Contrário as fases intermetálicas ordenadas esperadas pela metalurgia clássica, fase simples em solução sólida com estruturas CCC e CFC têm sido encontradas nos sistemas de ligas de alta entropia. O objetivo do presente trabalho foi preparar e caracterizar as ligas selecionadas FeCrNiCoAlCu e FeCrNiCo(AlCu)0,5. A preparação da liga foi realizada em forno a arco voltaico em atmosfera protegida. A caracterização microestrutural foi realizada através de microscopia ótica e microscopia eletrônica de varredura e por difração de raios-X. A caracterização mecânica foi realizada por medidas de dureza Vickers e por ensaio de compressão a frio. Os resultados mostram que ambas as ligas são constituídas por soluções solidas de estrutura dendrítica. A microdureza e o limite de escoamento compressivo da liga FeCrNiCo(AlCu)0,5 foi superior à liga FeCrNiCoAlCu.

Aug 8, 2018

By Malcolm Flavel

Dado que la trituración constituye el componente de alto costo en la mayoría de procesos mineros, se utiliza una tecnología basada en el resultado de los programas de investigación desarrollados por Allis-Chalmers Corporation. donde se busca reducir paulatinamente dichos costos. En ese sentido, el presente texto señala cómo reducir el consumo de energía requerida por el proceso de trituración y así minimizar la inversión de capital necesaria para construir las instalaciones del procesamiento.

Mar 1, 1983

By Alex Maia do Nascimento

Durante a produção de aços em fornos elétricos a arco (FEA), o hidrogênio pode ser incorporado ao banho líquido através de diversas formas: umidade das matériasprimas, umidade do ar (no momento de abertura do arco elétrico), umidade dos refratários e etc. A fragilização por hidrogênio (FH) é um fenômeno decorrente da incorporação e retenção de hidrogênio, acima de certo nível tolerável para cada aço em particular, que gera altíssimas tensões internas e diminui, catastroficamente, a capacidade de deformação do material. O objetivo do presente trabalho foi encontrar a quantidade de hidrogênio (ppm) aceitável no aço inicialmente desenvolvido para fabricação de barras CA-50 (6,3 / 8,0 / 10,0 e 12,5 mm), obtidas em rolos por laminação a quente após instalação de uma nova máquina de lingotamento contínuo de tarugos. Para realização do trabalho foram realizados ensaios de dobramento a 180° conforme a norma NBR 7480/2007 e medições dos teores de Hidrogênio no distribuidor da Aciaria através do equipamento Hydris.

Aug 17, 2017

By Andrei Bagrianski, Marco Nieto, Alexander Prikhodko

Se realizó una adquisición magnetotelúrica helicotransportada con el sistema MobileMT sobre un depósito metálico asociado a un pórfido de cobre conocido como Proyecto Santiago en el Cinturón Metalogénico Mioceno al sur de Ecuador. La adquisición geofísica se enfocó en identificar las respuestas de magnetometría y conductividad eléctrica y paso seguido, realizar inversiones unidimensionales y bidimensionales con el objetivo de caracterizar la respuesta petrofísica del sistema tipo pórfido. Los resultados arrojaron una anomalía de conductividad aparente mayor a 15 mS/m que se identificó como el cuerpo porfirítico en profundidad, llegando a estar entre 200 m a 600 m por debajo de la superficie.

May 10, 2023

By G. S. Scott

The Bureau of Mines is engaged in research to assess the hazards associated with the handling, storage, and use of combustible gases, vapors, and. liquids encountered in mines and in industry. As a part of this general pro-gram, numerous limits of flammability and ignition temperatures are being investigated for a wide variety of combustible materials, and methods are being developed to minimize the explosion hazards of these combustibles. The Bureau receives numerous requests for information on the explosion hazards of specified combustible mixtures under various conditions of use. This information circular has been prepared to assist those who may have similar requests. Destined primarily for the layman with a limited technical knowledge of the subject, it considers rather briefly the numerous factors that enter into the general problem of gaseous explosions and their prevention.

Jan 1, 1951

By G. L. Oldright

The studies previously made on Smelting in the Lead Blast Furnace have dealt with the custom smelter of the International Smelting Co. at Tooele, Utah,4 and on the smelter of the Bunker Hill & Sullivan Mining & Smelting Co.5 at Kellogg, Idaho. The International plant may be considered representative of the traditional custom smelter. The lead smelter of the future seemingly will have to treat increasingly richer lead charges. This feature was then stressed in describing the Bunker Hill plant.

Jan 1, 1934

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By Kristian Drivenes, Steinar L. Ellefmo, Kurt Aasly, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Since Ellefmo et al. (2014) published resource estimates of undiscovered seafloor massive sulfides (SMS) on the Arctic Mid-Ocean Ridge (AMOR), there has been an increased focus on establishing new knowledge about exploitation technologies for such deposits. This also includes understanding the process mineralogical properties of typical SMS deposits.The part of the AMOR that lies between Jan Mayen and the Svalbard Islands and is located within Norwegian jurisdiction and, as such, investigating the potential for mineral production from hydrothermal vent fields has been seen as strategic. The AMOR has been explored for active hydrothermal vent fields since early 2000s (Pedersen et al., 2010b). One of the active vent fields discovered, Loki´s Castle, is located in the northern part of Mohn´s Ridge. This vent field was first described by Pedersen et al., (2010a) and consists of two mounds, each approximately 100-150 m diameter and 20-30 meters high, hosting several active chimneys, up to 11 m high.Loki´s Castle has been selected as a case site in order to study the properties of typical SMS occurrences with respect to possible future deep-sea mining activities. As part of the MarMine cruise in 2016, the Loki Castle was visited and sampled for e.g. mineral characterization and mineral processing analyses. In total, more than 500 kg rock samples were collected using ROVs, and intended for further research (Ludvigsen et al., 2016). In addition to sampling mineralized rock fragments, survey data like bathymetry, magnetics and Underwater Hyperspectral Imaging (UHI) was collected using Automated Underwater Vehicle (AUV)."

Jan 1, 2017

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By Changshou Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,175 t (3,500 st) of ore per day with an average gold grade of 12.6 g/t (0.4 opst). The mine has a large horizontal extent of 762 by 152 m (2,500 by 500 ft) and a vertical extent of 6 to 61 m (20 to 200 ft). Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for mining design and operation in the Leeville underground mine. Three methods are used to collect the geotechnical data in the Leeville underground mine: • Core logging. Most geotechnical data are collected by this method, which is based on exploratory drills and estimates parameters for rock quality designation (RQD), fracture frequency (FF), compressive strength and rock mass rate (RMR). • Site investigation. This method collects more detailed geotechnical data and geostructural data from work done in the underground drifts and stopes. Parameters of RQD, FF, compressive strength, RMR, rock tunneling quality index (Q) and geostructural data are estimated. • Data collected from drill holes made for the critical infrastructure facilities. This method provides the best detailed geotechnical information for areas in which the critical infrastructure located. A complete geotechnical database has been constructed using this geotechnical data collection system. The database can be used for the design of ground support, stopes and stope blasts, among other critical applications.

Jan 1, 2010

By J. M. Woodall

GuAs crystals which have been grown in quartz boats by the horizontal Bridgman method in the pvesence of Ga20 vapov have beetz found to have carrier and donor distributions which do not correspound to those expected from simple dopant seg-vegation during directional freezing; Instead, the carrier distribution is determined by the heat-trentnzent history of the crystal, while the donor distribution, zohiclz is principally due to silicon, is fixed by the pozuth rate, the geo)tlet.ry of the crystal growth vessel, and tlze initial Ga20 pressure. WHEN semiconducting materials are made into doped crystals by the normal freezing method,&apos; they usually exhibit doping variations along the growth axis. If a) there is no dopant diffusion in the solid, b) the dopant is distributed uniformly in the melt, and c) the distribution coefficient, k, does not vary with composition, then the doping variation along the growth axis is represented by the equation: where C is the doping level in the solid at a point where a fraction g of the original liquid has frozen, and Co is the mean concentration. When the dopant is either a singly ionized shallow donor or shallow acceptor, C also represents the carrier concentration. Even though this equation accurately describes the dcping profiles of a large number of normal freeze systems, there are several special systems for which Eq. [I] does not apply. One such system is the horizontal Bridgman method for preparing oxygen-grown GaAs crystals using quartz vessels. Several workers2"* have shown that GaAs crystals grown by the horizontal Bridglnan method using quartz vessels are generally contaminated with silicon in concentrations in excess of 5 < 10lG atoms per cu cm. This contamination is ascribed to a reaction: occurring at the walls of the crystal-growth vessel which liberates silicon into the melt and Ga2O vapor. It has been shown4 that this reaction, and, hence, the silicon contamination, can be suppressed by the addition of oxygen to the crystal-growth apparatus. It is the purpose of this paper to describe a special apparatus capable of yielding single crystals of GaAs grown in the presence of oxygen and to describe both the kinetics of silicon suppression in this system and the relationship between the carrier concentration profile and the silicon concentration profile. EXPERIMENTAL-CRYSTAL GROWTH A schematic diagram of the apparatus used in the oxygen addition experiments is shown in Fig. 1. The most important features of this apparatus are: a) the use of a sand blasted quartz boat, h) a quartz rod of length 1, with a hole of cross section A, that is placed near the boat to limit the free space volume V, over the melt during the growth, and c) the temperature gradient at and near the solid-liquid interface. Sand blasting the boat is necessary to prevent wetting of the melt. The quartz rod retards the diffusion of the GazO vapor away from the melt to the colder portions of the ampoule. A crystal is prepared by first loading a 5.5-in. boat, which has been cleaned in aqua regia, with 40 g of 99.9999 pct Ga along with 1 to 8 mg of Ga203 powder. GazO3 is a convenient source of oxygen since it reacts with gallium at the melt temperature to form Ga20 vapor, the species which apparently controls the suppression of silicon contamination. The loaded boat, the quartz rod, and the 99.9999 pct As are placed in the ampoule as shown in Fig. 1. Generally, GaAs seeds were not used since most of the unseeded growths resulted in monocrys-tals. The ampoule is evacuated to 10-5 Torr and sealed off. The GaAs melt is synthesized by placing the ampoule into a two-zone horizontal Bridgman furnace. The two zones are separated by several sandwiched layers of -in. Fibre-Fax board drilled with holes slightly larger than the OD of the ampoule. This causes a very large temperature gradient between the two zones, which is necessary for single-crystal growth. The two-zone furnace is mounted on a stand fitted with a roller bearing which allows uniform motion of the furnace in a horizontal direction. A uniform velocity of the stand is achieved by the use of a windlass device which winds up a wire attached to the stand. Movement of the solid-liquid interface is accomplished by fixing the position of the ampoule and moving the stand. Growth rates investigated in this experiment were between 0.4 and 1.2 in. per hr. The composition of the melt is fixed by maintaining an arsenic reservoir at 618°C. The stand is moved away

Jan 1, 1968