Search Documents

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By Masaru Sakakibara, Ngo Tuan Anh, Mitsuo Nozu

"In the southern region of Vietnam and the southern United States, numbers of Deep Mixing (DM) columns have been installed to increase the stability of slopes and mitigate ground settlement. However, in some cases, there were some quality problems for in-situ cement mixing such as inclusion of unmixed lumps. According to the investigations by the X-ray diffraction analyses, electrical conductivity (EC) test, and careful observations of in-situ mixing quality, it has been observed that the existence of expansive soil and its high EC value cause the insufficient in-situ mixing. The countermeasures to address these problems have been taken.INTRODUCTIONIn South Vietnam, under the guidance of numbers of references and standards (Miki, 1998, JGS, 2000, Kitazume et.al., 2001, BS 2005), Deep Mixing (DM) has been used in recent years for soft clay improvement to increase the stability of slopes and to reduce consolidation settlement (Nozu 2005, Tung et.al., 2009, S. T. G. Peng et.al, 2009). However, at the initial phase of the DM operation, the authors have encountered some unusual phenomena such as (1) lower strength and inclusion of unmixed lumps (Figure 1), (2) less amount of up-heaved soil, and (3) sticking of large lumps of clay to the mixing blades. In regard to the above (3), Photo 1 shows one of the countermeasures against the sticking. By means of the placement of additional plates, the stuck clay has been reduced significantly.Subsequently, we have noticed that the quality of DM columns has not been so good, which meant that there have been some unmixed lumps in the column despite high cement dosage such as more than 300kg/m3. The authors also have encountered the similar incidents in Vietnam and United States during the deep soil mixing work. For example, Photo 2 is the core samples taken from the DM test column in northern Vietnam adopting cement injection during penetration (CIDP) procedure. To solve this problem, various tests and investigations have been performed so far (Nozu 2010, 2012)."

Jan 1, 2015

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930

Who Macraes Mining Company Limited is can be summed up by the following statements: +         We have been New Zealand's largest gold producer for seven years +         We have one of the lowest market capitalisation per reserve ounce of the gold producers in the  Australian Gold Index +         We have a resource finding cost of less than NZ$l0 per ounce +         We have a large land bank with proven reserves +         We have an Operating Cash Margin of approximately NZ$200 per ounce +         We have reduced our Dry Milled Tonne Cost by 34% since 1992   Our Mission is to continually grow our gold business, through maximising cashflow and focusing on our value drivers being: +         Increasing reserves +         Increasing cash operating margins +         Increasing production   The real challenge is the reduction of operating costs and the optimisation of revenue, particularly in the current gold price environment.   The Company has as at 31 December 1996 total mineral resources of 6.1 million ounces and reserves of 3.4 million ounces. This together with our current cash position of approximately NZ$15 million and strong hedging book of approximately 800,000 ounces places the Company on a sound financial footing whilst positioning itself to aggressively pursue its growth strategy when gold price and market conditions improve.

Jan 1, 1997

By E. C. Lane

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of samples of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 3162/4 is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of sample of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 31624/ is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By Elmer Ccahuana, Filiberto Mamani

La determinación del tajo óptimo involucra varios aspectos como la metalurgia, costos operativos, precios de metales, etc. para dimensionar la geometría del tajo. No obstante, la metodología tradicional no incluye el blending3 como parámetro de optimización del tajo a pesar de que existen muchas minas a tajo abierto, en especial auríferas, que emplean la mezcla de materiales para el procesamiento de los mismos. Pysight4 es un algoritmo que permite determinar el tajo óptimo por aproximación a través de generación de tajos para los escenarios en base a la combinación de las leyes de corte por materiales.

Sep 29, 2023

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977

By Violeta Vigo, Sara Laughton

Cajamarca es uno de los departamentos con mayor historia y presencia del sector minero a nivel nacional; sin embargo, en la región solo el 22,9% de la población adulta accede a créditos formales en el sistema financiero (INCORE, 2022). Las mujeres tienen más restricciones que los hombres para acceder al crédito formal. Respondiendo a esta problemática; desde el 2008, en colaboración con el Banco de Desarrollo del Perú (COFIDE), la Asociación los Andes de Cajamarca (ALAC) fundación empresarial de Minera Yanacocha, viene implementando un proyecto de educación financiera que apoya a las comunidades locales a optimizar la gestión de sus ingresos y ahorros.

Sep 29, 2023

By Isaac Minaya, Jhonny Torre, Mario Carpio, Jesús Fuentes

El litio se considera un elemento estratégico debido a sus diversos usos en industrias tales como la electrónica o la automotriz. Por ello, se debe entender cuáles son los ambientes geológicos (pegmatitas, ambientes volcánicos, ambientes metamórficos y cuencas endorreicas en relación a salares y salmueras) asociados donde alberguen los minerales de litio (silicatos, sales y/o salmueras). Para llegar a ello, se deben conocer las características macroscópicas geológicas de campo y fundamentar su interpretación por medio del apoyo de la instrumentación en los tipos de análisis químicos, mineralógicos, las características microscópicas petrográficas y la caracterización puntual de algunas muestras por la microscopía electrónica de barrido (SEM). Por tanto, en esta publicación se presentan datos preliminares de ocurrencias con valores anómalos de litio en afloramientos de rocas volcánicas, intrusivas (graníticas), aplíticas y metamórficas dentro de las unidades morfo estructurales del Altiplano y la Cordillera Oriental, ubicadas en las regiones de Cusco y Puno. En la zona de Corani (Puno) afloran rocas volcánicas tipo tobas de lapilli con altos contenidos de litio entre 2815 a 3070 ppm, cuya presencia se relaciona a los minerales de micas de litio, denominado lepidolita, como constituyentes inmersas en agregados granoblásticos de cloritas y silicatos, perteneciente al miembro Sapanuta de la formación Quenamari. Por su parte, en la zona de Ocongate (Cusco) las ocurrencias con anomalías de litio (1096 ppm) se encuentran asociados en clinocloros y/o amorfos asociados como constituyente dentro de cuerpos de areniscas, con presencia de vetas de cuarzo, sulfatos de cobre, óxidos de hierro, trazas de pirita y calcopirita, pertenecientes a la formación Ananea.

Sep 20, 2019

"The most common comminution testing methods and the associated analytical procedures provide average values and do not capture the variability in breakage behaviour of ore particles. Therefore, plant designs and process performance predictions use only average values; hence, the inherent variability that exists within an ore domain translates into variation in process performance. This paper discusses the drawbacks of using the average approach to impact comminution testing and plant design. It considers breakage intensity from a single-particle testing perspective. To clearly delineate breakage behaviour of each broken particle, an experimental technique using the JK Drop Weight Tester (JKDWT) has been developed by which actual comminution energy per particle and breakage intensities were measured directly. Four different ore types in ranges of -45+37.5mm and -22.4+19mm were tested at three energy levels of 0.1, 0.25, 0.5 kWh/t and six energy levels of 0.5, 1.0, 2.0, 2.5, 3.0 and 4.0 kWh/t, respectively. Sieved results of individual particles, notionally, t5, t10 and t50 showed the presence of large variability in their breakage behaviour, which was not captured by the standard JK impact breakage testing approach. In addition, the original JKMRC model is modified by introducing a third parameter, ‘Emint10’ which describes the minimum energy required to produce the minimum percent t10 for a given ore type and its significance is tested statistically. These results suggest that the analysis of breakage variability may lead to more robust plant designs. Perhaps, the most useful insight from this work is to extend single particle breakage model developed by JKMRC to a comminution percentile envelope which may provide a more detailed picture of ore breakage variability. INTRODUCTION Rock consists of mineral grains, pores, voids and cracks that may differ markedly in size/density which make rock a heterogeneous material by nature. The degree of heterogeneity in rock affects its breakage characteristics where these variations increase local differential strain and stress within a stressed rock (Scholz, 1968) and it depends on many factors such as rock genesis, alterations, etc. One important aspect of this heterogeneous feature is presence of a large amount of experimental scatter in rock breakage results when considered from a quantitative perspective (Bieniawski, 1967; Liu, Roquete, Kou, & Lindqvist, 2004)."

Jan 1, 2018

By Mark Sanders

The report describes three experiments that were conducted to determine the effects of size and weight of the miner's battery pack on performance in the low seam coal environment. Three separate experiments were carried out in a simulated low seam coal mine. The first experiment tested the sensitivity of task measures (i.e., subjects performed locomotion) shoveling, cart pushing, and timbering tasks) to detect variations in the size and weight of the battery pack. The results of the first experiment demonstrated that only the locomotion tasks were sensitive to size and weight variations. The second experiment, therefore, focused on the locomotion tasks and tested the effects of varying size and weight on task completion time. The third experiment was designed to compare the present battery pack to a radically different configuration of power cells. The most important findings were that changes in weight affected locomotion times but changes in size and configuration had small and inconsistent effects. Opinion data of subjects indicated a strong preference for a battery nark belt concept.

Jan 1, 1980

By A. E. Kehew

Earth resistivity surveys using the Wenner electrode configuration were made in unmined areas and reclaimed spoils at three surface lignite mines in western North Dakota. The study sites were the Center, Indian Head, and Falkirk Mines. Automatic interpretation of the curves was accomplished with the method of Zohdy and Bisdorf (1975). Overburden materials become more homogeneous with respect to resistivity during the mining and reclamation process. The spoils curves show localized hetero-geneities probably related to discontinuous moisture content variations in the spoils. Consistent resistivity differences in spoils occur between mines with over-burdens of different mineralogic compositions. Groundwater chemical composition in terms of total-dissolved-solids (TDS) is inversely correlated (r=-0.61) with apparent resistivity at the 80-foot spacing from a survey centered at a piezometer screened near the base of the spoils. Better inverse correlation is probably pre-vented by high variability in TDS within the spoils groundwater. A useful predictive relationship may be the plot of mean apparent resistivity at the 80-foot spacing for ar. entire mine against mean TDS for all wells in spoils at that mine. Data from more mines are needed to test the hypothesis.

Jan 1, 1982

By Bertrand L. Johnson

Pure talc is a hydrous magnesium silicate (Mg3Si4010(OH)2). Pyrophyllite, although it resemble: talc in certain physical properties and uses, is a hydrous aluminum silicate (Al2Si4010(OH)2) - like kaolin, except that kaolin has a somewhat different composition (Al2Si205(OH)4) and structure. Soapstone can be considered essentially an impure talc grid when pulverized is used for many of the same purposes as talc. Massive, compact varieties of talc often are called steatite. PROPERTIES Talc and pyrophyllite are characterizes; by their softness (hardness on Mohs' scale, 1) their greasy feel, pearly luster, white color, and perfect basal cleavage. They have similar crystal structures, and this similarity explains the close resemblance of the two minerals in physical acid chemical properties. Talc is a good electrical insulator, resists the action of most acids and alkalies, and has an exceptional heat-retaining capacity. Its specific gravity is about 2.7.

Jan 1, 1939

By A. G. Starliper, H. Kenworthy

A procedure was developed for the separation of lead and sulfur in industrial concentrates of galena by a combination of chlorination and fused - salt electrolysis . Galena could not be satisfactorily electrolyzed in the various media tried ; however , when it was treated with chlorine the resulting lead chloride could be effectively separated electrically into lead and chlorine . An apparatus was designed and constructed to chlorinate galena and to volatilize simultaneously most of the chloridized impurities . By electrolyzing the chlorinated concentrate , a high percentage of lead was recovered . Anodic chlorine was drawn from the cell and was used to chlorinate new feed . In many runs , the recovered metal analyzed from 99.8 to 99.9 percent lead . Lead was also distributed as a chloride in the bath , and a small portion was in the volatile fraction produced during the chlorination step . During a tinuous operation , only 0.1 percent of the total lead was discarded ; 99.9 percent was accounted for in the metal , electrolytic bath , and washed or leached chlorination condensate which was essentially lead chloride . About 95 percent of the sulfur from the galena was recovered as a byproduct of over 90 - percent grade .

Jan 1, 1964

By Alfred Petrick

This report analyzes the byproducts systems of lead, zinc, uranium, rare earths, iron, aluminum, titanium, and lithium. Specific byproduct metals covered are cadmium, germanium, indium, and thallium from the zinc system; antimony and bismuth from the lead system; vanadium, radium, and scandium from the uranium system; rare-earth oxides from the rare-earth system; and cobalt, gallium hafnium, and rubidium from other systems. The report discusses various metallurgical systems, marginal and incremental production costs of byproduct subsystems, industry structure and organization, and historical data on price, consumption, and supply.

Jan 1, 1973

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By R. E. Allen

THERE was once a time when a practical oil man would appraise or buy a producing property on the basis of from $200 to $500 per barrel of average daily settled production. Curtailment-has, for the present at least, caused a virtual abandonment of the "barrel -of settled production" as a yardstick of, oil property value and in its place has come the "barrel of allowable production," which, although an artificial thing, is nevertheless now the principal factor governing the rate of ?pay out? or investment return. The potential production of a well, settled or otherwise, is of less importance in determining the present worth of a well than is the rate at which it may be produced. Speaking only of true potential for the moment, it is obvious that of two similar wells having the same potential, the one having the highest rate of allowable production would be worth proportionately more than the one of lesser allowable. The discount factor for deferred return and risk can easily vary the present values of the two wells by as much as 20 per cent when allowable rates are not greatly different.

Jan 1, 1934

THIS paper is the outcome of experiments carried on and experience gained. at the Waihi-Paeroa Gold Extraction Company's tailings plant at Waihi, New Zealand. The plant was erected to treat accumulated tailings which had been discharged into the Chinemuri River by the Waihi batteries.The Chinemuri River is a common sludge channel for all mining debris, tailings, and ashes from the power plants, the last being the cause of occasional high residues, which gave so much trouble to the management. The tailings were dredged from the bed of the river into barges by means of a Pohle air lift, the power being supplied: by a 13 b.h.p. Tangye oil engine driving an air compressor and a centrifugal pump. The sands were elevated from the barges by bucket-belt elevators over screens, to eliminate large particles and rubbish, into storage hoppers, and from there fed direct into four C. Judd Ltd. tube mills.The method of treatment was fine grinding in a weak cyanide solution, agitation in B. and M. tanks, filtration with turn-over vacuum filters, and precipitation with zinc shavings. The comparatively high values of the residues in gold gave a great deal of trouble, 'and it was not until repeated experiments were carried out that the cause of the trouble was located. While the value of silver residues remained stationary, the gold values...

Jan 1, 1912

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964