Search Documents

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this con¬dition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By Martina Cadorin

Activated nanoporous biocarbon (aNBC) was prepared using E. grandis wood as a precursor material. Oxidated activated nanoporous biocarbon (ox-aNBC) sample was obtained from the aNBC by oxidation with nitric acid. The samples were tested as Pt nanoparticles catalysts support for ethanol oxidation reaction and as electrode materials for supercapacitors. The porous structure, chemical properties, and the structural and morphological characteristic of the materials were correlated with their electrochemical behaviour. Biocarbon materials showed similar high specific surface area. The oxidation treatment increases the content of the oxygenated and nitrogenated surface functional groups but without appreciably change in the nanostructure characteristic. The aNBC supported Pt nanocatalyst has better electrocatalytic performance for EOR. Oxygenated functional groups have a marked effect on the supercapacitors electrode behaviour, increasing the total electrical capacitance by pseudocapacitive contribution, but with a negative effect on the cell electrical resistance and cell response time.

Oct 30, 2017

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

By Yuexin Han, Wenbo Li, Xinran Zhu, Pengchao Li

A multi-stage fluidization magnetization roasting is a promising method to treat limonite ore. The dehydroxylation of limonite ore is a key reaction in the pre-heating stage. In this study, the dehydroxylation mechanism of limonite was studied in a laboratory fluidization roasting reactor. The samples were characterized using in situ X-ray diffraction, Fourier transform infrared spectroscopy, and simultaneous thermogravimetry and differential scanning calorimetry analysis. The phase transformation and kinetics analysis were studied. Results indicated that the dehydroxylation occurred at the temperature of 250–350 °C with the vanish of hydroxyl functional groups (-OH). The dehydroxylation kinetics followed the 2-D diffusion (Jander) reaction model G(α) = [1 − (1 − α)1/2]2, and the calculated activation energy was 113.43 kJ·mol−1. This study is conducive to exploiting limonite ore resources using magnetization roasting technology.

Nov 2, 2023

By W. H. McAllister

The paper considers the geology and the coalfields that comprise the Scottish south area. It traces the history of known sources of spontaneous combustion and indicates the collieries concerned, with the position of the seams in the geological series where heatings have occurred. The methods of work over the years are described. It relates in detail the circumstances surrounding a fire at Bilston Glen Colliery in the Lothian Coalfield, and the heating at Killoch Colliery in the Ayrshire Coalfield, and the steps taken to deal with them. It also describes some of the difficulties in steep seam working. Methods adopted to prevent spontaneous combustion throughout the area are discussed, and some detail of the UNOR gas analyser is given. Finally, it comments on the present techniques in use in the area, particularly at Bilston Glen Colliery, to prevent spontaneous combustion.

May 23, 1905

By Manuel Gomez

Coking time was investigated as a function of coal properties, carbonization parameters, and the interactions between these variables. The results indicate that coal properties and carbonization conditions interact to influence the coking time, and these interactions may be determined quantitatively. Prediction equations were developed and used to simulate the effects of bulk density, flue temperature, and oven width on coking times for coals having a wide range of properties. The data presented provide additional information on the carbonization process to permit the coke oven operator to maintain closer control of coke production and coke uniformity.

Jan 1, 1968

By Rodrigo Vitorino da Silva

Ligas a base de zircônio utilizadas na indústria nuclear estão sujeitas à formação de hidretos que são causadores de efeito deletério no material. Para aumentar o tempo de operação desses componentes, é necessário o desenvolvimento de novas ligas que retardem ou diminuam esse efeito. Este trabalho tem como objetivo avaliar a influência da adição de elementos de liga em uma liga inédita a base de Zr-Nb na absorção de hidrogênio, através de testes que avaliam a absorção de hidrogênio e a formação de hidretos no material após processamento termomecânico e comparar seu desempenho com duas ligas comerciais. Para tal, foram realizados ensaios de microdureza, cinética de absorção de hidrogênio e micrografias. Os resultados de microdureza Vickers das três ligas estudadas, após o processamento termomecânico, são muito próximos. As curvas de cinética de absorção de hidrogênio mostram que a liga Zr-Nb-Sn-Fe apresenta melhor comportamento que as demais uma vez que o tempo para o início de absorção foi maior. As micrografias indicam que a liga proposta apresenta um desempenho superior em relação à morfologia dos hidretos visto que os mesmos são mais curtos e alinhados.

Aug 17, 2017

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By S. Borle

The microstructural features produced in friction stir welded AZ31, AZ80 and AZ91 alloys are examined when different welding parameters are applied. The microstructures primarily consist of a-Mg grains with a-Mg + Mg17A112 colonies, however melted films of Mg17A112 are produced in AZ91 alloy when high rotation speeds are applied. When the rotation speeds are slow, or the travel speeds are fast the Mg17A112 were incorporated into the stir zone, however they do not exhibit an elongated lamellar morphology associated with melted films. In the case of AZ80, the extruded base material contains a smaller fraction of Mg17A112 and few of these phases are observed in the stir zones. The results are explained based on the dissolution rate and melting temperatures of Mg17A112 controlling the overall morophology and fraction of phases in the stir zone.

Jan 1, 2011

By Russell G. Wayland

THIS paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. MUSCOVITE MICA Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. THE MICA PROBLEM Block muscovite mica is commercially classified into the following general qualities, beginning with the best quality: I. Clear and Slightly Stained (C & SS). 2. Fair Stained (FS). 3. Good Stained (GS). 4. Stained (S). 5. Heavy Stained (HS). 6. Black Spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately I C & SS to 4 FS to 10 GS to 14 S to whatever the

Jan 1, 1944

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005

By R. G. Knickerbocker, C. T. Baroch, A. W. HACKWOOD

The difficulties inherent in the production of alumina by the formation of potassium alum and its subsequent thermal dehydration and decomposition have been overcome , to a large extent , in a process developed at the Boulder City Station of the Bureau of Mines . This process is applicable to the reserves of alunite known to occur in several Western States and , possibly , to certain clay and low-grade bauxite deposits known to exist in this country . The operations sequence of the process is shown in the flow sheet (fig . 1) . Only those steps included within the heavy line are considered in this report . Four different procedures for dehydration of alum were investigated ; ( 1 ) Spray drying , ( 2 ) rotary - kiln drying , ( 3 ) dry grinding in a thermal ball mill , and ( 4 ) dehydration in the vertical- column flash dehydrator . Based upon fuel requirements and other practical considerations , the vertical- column dehydrator , or some modification of its operating principle , offers the botter possibility for commercial use .

Feb 1, 1946

By B. Meddings, O. J. I. Evans

"This paper is mainly concerned with the present and probable future role of hydrometallurgy in the production of base metals.The economic and technological bases of the hydro-metallurgical plants built and operative in the mid-fifties are compared to those in production in the mid-sixties. The trends observed are extrapolated and some estimates made concerning the probable size and type of hydrometallurgical plants which will be operative in the mid-seventies.The impact of emerging socio-economic factors such as pollution control and the market demand for specialized metal products which favour hydrometallurgical recovery processes are also discussed."

Jan 1, 1971

By T. Bednarski, T. McCallum, L. Moya, B. Gay

"Molybdenum recovery by solvent extraction has gained interest partly due to advances in concentrate leach technology. Historically, both molybdenum and rhenium have been produced using amine-based extractants with the ability to co-extract both metals. Alternatively, a phosphinic acid-based extractant (CYANEX® 600) can be used depending on the flow sheet. CYANEX® 600 selectively extracts Mo leaving Re in the raffinate, which is a valuable feature in plants which require rejection of the rhenium from the molybdenum circuit. CYANEX® 600 piloting results are reviewed and compared to commercial experiences with an amine-based extractant. INTRODUCTION Molybdenum is most commonly found as molybdenite (MoS2) in primary porphyry deposits (about 59% of global reserves) and copper porphyries (about 39% of molybdenum reserves)[1]. Recovery from molybdenite traditionally involves flotation (concentrates typically containing 85 – 95% MoS2) followed by roasting to produce MoO3. Solvent extraction is also used to recover molybdenum from acidic aqueous solutions resulting from scrubbing of roaster and smelter off gasses and leaching of molybdenite (uranium ores). Molybdenum is also frequently found in low concentrations in copper leach inventories[2]. More recently, pressure oxidation has gained interest to treat molybdenite concentrates. Molybdenum Chemistry The chemistry of molybdenum is complex with a series of extractable species existing dependent on the pH and oxidation state as shown in Figure 1.Under strongly basic conditions, molybdenum primarily exists as MoO42- while under strongly acidic conditions MoO22+ becomes the predominant species. In between, a number of isopolymolybdates such as Mo7O246- and Mo8O264- are dominant. Equations (1) – (3) demonstrate some of the proposed molybdenum equilibrium reactions[1]."

Jan 1, 2017

By John C. Taylor

With growing emphasis on energy conservation and increased concern over the presence of heavy metals in the environment, it is fortunate that most metals are readily recycled. In this respect, metals have a significant advantage over plastics and similar materials used as metal substitutes. For many years a secondary industry has processed scrap copper, nickel, lead and zinc to produce refined metal which has, to varying degrees, influenced the price and displaced the production of primary metal. This paper reviews some of the challenges the industry will face and the changes in process technology which will be required as pressure mounts to increase the amount of metal recycled. In the case of most base metals, this will have an impact on primary metal production; as the tonnage of metal recycled increases, the requirement for primary production, or new metal, will depend more and more on the growth in consumption.

Jan 1, 1993

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

By Guy E. Dent, Hugo E. Kuehn

"SUMMARYFor making a comparison of magnetic surveys measured from the ground and from the air, Worcester County, Maryland, was chosen as a proving ground. Vertical magnetic intensities were observed on the ground, and total magnetic intensities were observed from the air. A comparison of the two magnetic maps reveals similar large magnetic features, but these are displaced in some instances by distances greater than a mile. Magnetic terrane in the two charts is of the same type but often differs greatly in respective characteristic features.The sacrifices in accuracy that may be expected from the use of different systems of diurnal magnetic corrections on ground observations constitute a part of this report.INTRODUCTIONThe value of magnetic surveys for gaining information concerning the crystalline basement is recognized increasingly. That this topography is often reflected to a major degree in the overlying sediments with certain offsetting is well understood. Even where such sediments are deep, the surface topography of upper formations often reflects this bedrock topography to a certain degree."

May 1, 1947

By Venilton de Camargo Barbosa

Levando-se em conta o grande número de ligas Ni-Cr existentes nos mercados nacional e internacional bem como a variedade de elementos de adição, neste trabalho foram preparadas diferentes composições experimentais de Ni-Cr-X (X = Ta, Mo, W, Nb e Ti) para avaliar o efeito da adição do terceiro elemento na resistência à corrosão destas ligas em meio de fluoreto. As composições utilizadas foram escolhidas tomando-se como referência a de uma liga Ni-Cr-Mo amplamente comercializada no mercado odontológico. De acordo com os resultados obtidos concluiu-se que as respostas eletroquímicas dividem as cinco composições em dois conjuntos distintos, com respeito ao comportamento corrosivo, sendo as de maior resistência à corrosão aquelas em que X = Ta, W ou Mo, enquanto que, a corrosão localizada foi observada para X = Nb ou Ti.

Aug 7, 2018