Search Documents

Properties of coal which are significant in relation to preparation for carbonization and conversion are reviewed, and existing coal preparation technology which has been used for production of cleaned coal of suitable ash content and petrographic composition for carbonisation, pyrolysis, hydrogenation and similar processes is described. Possibilities for application of this technology to some Australian coal seams is examined briefly. It is concluded that further survey work is required related to the optimization of selective crushing and concentrating operations, with the aim of maximizing production of quality products for carbonisation, etc mainly from Australian seams with only moderate coking characteristics.

Jan 1, 1980

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By Paul L. Michael

Roof warring signals from eleven underground coal mines (principally in the Pittsburgh seam) were studied and analyzed. The character of individual acoustic warning signals is shown to be dependent on spectral distribution of energy. Reverberation tires (pulse decay rates) were found to be usually between 0.1 and 0.5 seconds. Listening tests were conducted to assess the miner's ability to discriminate speech and roof talk signals in noise and in quiet, with and without ear protectors and with various levels of hearing loss. The ability to detect roof talk is shown to be generally degraded while wearing car protection in quiet, although, if car protectors are worn only when required by high noise levels, the ability to detect roof talk will be preserved at its maximum.

Jan 1, 1972

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By D. Hodouin

Jan 1, 1978

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By C. E. Abbey, M. S. Moats

It is well known that the addition of cobalt to copper sulfate — sulfuric acid electrolytes decreases the overpotential for oxygen evolution and decreases the rate of corrosion of Pb–Ca–Sn anodes. This effect, however, has not been ade- quately quanti fied in the presence of iron and manganese in this type of electrolyte. This work provides quanti fiable data on the effect of cobalt concentration in the range of 0 –0.6 g/L in synthetic electrowinning electrolytes with and without the presence of iron. The effect of cobalt on anode potential was determined using 2 and 24 h chronopotentiometry experiments. As expected, Pb–Ca–Sn potentials increased with decreasing cobalt concentration over the range of 0–0.6 g/L Co with and without the presence of Fe. Two regression models were developed to allow plant operations the ability to predict anode potentials as a function of cobalt concentration with or without iron in the electrolyte.

Mar 1, 2017

A new lead refinery with a capacity of 230,000 tons per year commenced operation at Port Pirie in October, 1959. This plant superseded the refinery which had operated from 1933 with the advent of the continuous lead refining process. The incorporation of new equipment following local metallurgical developments, together with the overseas demand for lead of extremely low antimony content createddifficulties in operating the original plant. The new refinery project was undertaken to cover this disability and to gain the full advantage of the new processes.Desilverising and softening are carried out in units identical in size to those used previously. Metallic zinc is recovered from the entire output of desilverised bullion by vacuum distillation. Final refining is carried out by batch treatment with caustic soda yielding lead of purity previously unattainable at Port Pirie.These two processes replace continuous dezincing by oxidation, a high temperature process which caused large quantities of lead and antimony to be recirculated. The final stage is a batch process; therefore the product composition can be checked before casting. Individual batches can be adjusted to produce special alloys to consumer's specification.Improved casting equipment allows the quantity production of pigs of good physical characteristics either as 56 lb bars or 2000 lb pigs.This, together with the high purity of the lead, assures the Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.) position in world markets.Automatic control systems are extensively employed, particularly on the vacuum dezincing unit.The anticipated financial benefits have been achieved mainly by a reduction in the tonnage of recirculated materials, a smaller labour force, and reduced maintenance requirements.INTRODUCTIONIn December 1956 a decision was made to build at Port Pirie a lead refinery on a completely new site, and in October 1959 the new refinery was brought into operation. This plant superseded the lead section of the old refinery which...

Jan 1, 1963

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 rears, until in 1936 probably more than 90,000 such units were put into use. According to reports of the Bureau of the Census 79,543 residential stokers were sold in the first 10 months of 1937 by 109 manufacturers. This rapid expansion has made itself felt in the coal-mining industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912; in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of the present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

By J. C. Bothan

A program to provide technical in-formation on the use of fuels in pyro-metallurgical processes, from the Canadian fuel viewpoint, was initiated about five years ago by a Canadian Institute of Mining and Metallurgy liaison grou1> composed of members from the Coal Research Committee of the Coal Division and the Iron and Steel Committee of the Metallurgy Division. This paper is another of a series prepared for this program. Previous papers included a review of pyrometallurgical processes of Canadian interest, a survey of ferrous processes relevant to the development of an integrated steel industry in western Canada and a survey of the fuel requirements of the non-ferrous metals industry in Canada. It is widely recognized among per-sons familiar with the Canadian coal industry that, because of the large resources of coking coal in western Canada, the

Jan 1, 1963

By Marco Taipe

Uno de los mayores costos del proceso minero es el de perforación, en tanto emplea aire comprimido. Por tal motivo, la industria minera busca diferentes alternativas para reducir los costos del aire comprimido o eventualmente a través del uso del sistema electro-neumático. Este sistema es de fácil instalación y mantenimiento puesto que se basa en electricidad y agua, reduciendo costos y a su vez mejorando las condiciones de trabajo a través de la versatilidad del presente sistema.

Sep 12, 2011

By Samer Sadek

The Georgia Department of Transportation (GDOT) undertook an exploratory feasibility study to one of the most ambitious tunneling projects in the United States. HNTB Corporation was retained to perform the study, deemed the Atlanta North-South Tunnel, which is approximately 7 miles long and consisting of four lanes (or six lanes) starting at the southern terminus of SR 400 extending to the south connecting with the northern terminus of I-675, providing substantial relief to the Downtown Connector (I-75/I-85), the most congested portion of Atlanta?s freeway system. This paper summarizes the analysis performed during the first phase of this challenging assignment which, if constructed, would be one of the longest roadway tunnels ever built in the United States.

By R. Thomason

Thank you Dr Barcza, President of the South African Institute of Mining and Metallurgy, for inviting me to share our experiences in Australia as regards the competency movement and my Association?s experience in assisting engineers become managers. This is my second visit to South Africa, and I am struck by the similarities between our countries. This extends to the professional issues associated with engineering and competencies in particular. I propose to outline two exciting stories today. ? Development of competency standards for professional engineers in Australia. ? Development of a management programme which has assisted professional engineers regain positions of leadership in Australian industry and government. First of all I would like to outline the Association of Professional Engineers, Scientists and Managers, Australia(APESMA).

Jan 1, 1997

By C. R. Boyd

In 1874 I received an appointment in the corps organized by Col. William P. Craighill, U. S. Engineers, to survey the New or Upper Kanawha river for the purpose of ascertaining the practicability and

Jan 1, 1895

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

By MATT RENAUD, Mustafa Kumral

As high-quality mineral deposits are thoroughly exploited, mines of the future will have to move towards more remote and lower quality projects. With these projects comes an increased business risk to the operator. Even now, mining companies often turn to foreign countries for new deposits to produce, introducing the concept of country risk into their portfolio. Furthermore, feasibility studies often fail to accurately quantify the risks associated with various projects, and as such, this study proposes a technique of risk quantification which can both aid mining companies to evaluate the viability of investment and assist in risk disclosure to public investors for the mining industry of the future. This paper aims to quantify the effects of country risk on the valuation of potential mining projects, using a combination of modular and risk-weighting techniques to evaluate the country risk premium (CRP) required to obtain capital for operation of risky foreign mining projects. The techniques proposed in this paper are demonstrated using fictional examples and then evaluated for accuracy against a recently developed debt-funded precious metal project in a country in the Americas.

Sep 30, 2021

By B. J. Moore

This publication contains analyses arid related source data for 274 natural gas samples from 20 States. Of the total samples, 269 were collected during calendar year 1985; the reminder were collected earlier, but releases granting permission to publish were not received before 1986, All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1987

By Eugene McAuliffe

THE last obtainable figures of the value of the coal mining investment are those contained in the U. S. Census Reports, from data gathered in 1919. The values shown therein and set forth below cover lands and equipment and do not include distribution and marketing facilities. The working capital necessary to meet pay rolls to purchase material and supplies and workmen's compensation insurance are likewise excluded.

Jan 1, 1926