Search Documents

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By R Soong

The Wharekirauponga (WKP) epithermal gold-silver deposit is located about 10 km north of Waihi in the Hauraki Goldfield east of Auckland. WKP is notable for its sheeted to stockwork quartz veins hosted in rhyolitic rocks, that have attracted exploration interest as a low grade, bulk tonnage exploration target. Exploration between 1978 and 1993 included 23 diamond drill holes totalling 5505 m. The mineralisation occurs in a rhyolite dome complex (Miocene), consisting of flow-banded rhyolite and rhyolitic pyroclastic rocks, with minor andesite. Fifty four drill core samples were collected from six exploration drill holes and analysed by semiquantitative XRD techniques. Hydrothermal alteration of the rhyolitic and andesitic rocks has developed secondary mineral assemblages of quartz, adularia, albite, chlorite, illite, sericite, interlayered illite-smectite, carbonate, halloysite and pyrite. The main zone of mineralisation is characterised by quartzadularia alteration, which grades oiItward to quartz-clay (illite, local halloysite and/or interlayered illite-smectite) alteration. Propylitic alteration is present at the southern end of the drilled area of the prospect. Depth-related changes in mineralogy include a decrease in illite and appearance and increase in quantity of chlorite with increasing depth, and the localisation of halloysite and interlayered illite-smectite in the shallow parts of some drill holes.

Jan 1, 2001

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

By Charles Barnhart

This paper is a discussion of the causes of deflagration in cast blasting and a description of a project intended to demonstrate how changes in six critical parameters contribute to the deflagration chemical reaction. Control of these parameters is key to solving the nitrogen dioxide “orange smoke” problem. Preliminary results of an investigation into the development of a technology addressing the problem of atmospheric releases of nitrogen dioxide during cast blasting in surface mine operations are described. The project is funded by a $600,000 Small Business Innovative Research grant from the National Science Foundation and an $80,000 Abandoned Coal Mine Land Reclamation Program grant from the state of Wyoming. The presentation will address the measures required to control the blast chemical reaction so that it does not produce nitrogen dioxide through deflagration. Experimental blast data will be focused on a new shaped charge detonation system designed to instantaneously bring the powder column to maximum velocity of detonation (VOD), thus insuring efficient detonation of the entire colulnn.

Jan 1, 2003

THE township of Costerfield is situated in the parish of Costerfield, county of Dalhousie, and lies 6 miles east of Heathcote and 30 miles south-east of Bendigo. It is separated from Heathcote by the Mt. Ida Range, which forms the western boundary of the Silurian formation. It is situated at the head-waters of Tin-pot Creek, a small southerly tributary of the Deegay Ponds Creek, which flows east to the Goulburn River.The field was discovered in 1860 by two prospectors, Coster and Field, who were guided there by a shepherd, M Nicol Coster and Field had already discovered an antimony lode about three miles nearer Heathcote, when M Nicol offered to guide them to the larger outcrop. The main Costerfield reef at that time projected above the surface, and was white through oxidation, though the bluey sulphide showed on fracture. No alluvial gold of any consequence was obtained at Costerfield, but a little was obtained, at Redcastle, 7 miles to the north, and in some of the gullies to the east.Following its discovery there came a period of prosperity to Costerfield, while the mining operations were confined to the oxidized zone. The early success of mining at Costerfield was due to the gold values, and it is probable that the oxidized zone was secondarily enriched. The earliest available record of values is a crushing of Coster and Co. on the Antimony reef (now known as the Costerfield reef), when 200 tons from a depth of 70 ft. averaged 4 oz. per ton in July, 1861. At this time a crushing mill had not yet been erected at Costerfield, and the ore was carted and treated at Redcastle. The massive antimony ore, consisting of mixed oxides and sulphides, was separated by hand-picking as "marketable ore," and the remainder crushed for gold. A higher average is recorded from South Costerfield in September, 1861, when a 15' cwt. parcel...

Jan 1, 1922

De Beers? Finsch diamond mine began operation in the 1960s as a surface project using the latest technology available. During the 1990s, the operation, located about 160 km (100 miles) west of Kimberley, South Africa, began its move as an underground mine. The earlier stages (Blocks 1, 2 and 3) of underground work at Finsch used open stope mining methods, also using the latest in technology. The mine began developing Block 4 in 2004. How-ever, studies on this level showed that block caving was a more efficient mining method than open stoping. It was during those studies that De Beers determined that Block 4 would be a good candidate for testing Sandvik?s automated truck haulage technology.

Jan 1, 2008

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

By John A. Richards

This paper is one of a series being published by the Bureau of Mines on mining methods and costs. It describes briefly the manner in which slusher hoists and scrapers are used in connection with clock-caving methods at the Emma Nevada mine of the Consolidated Coppermines Corporation, Kimberly, Nev. Kimberly is in the Robinson mining district, White Pine County, 7 miles west of Ely. The district is served by the Nevada Northern -Railroad, which branches from the main line of the Southern Pacific at Wells, Nev., 140 miles north, Paved U. S. Highway 50 from Salt Lake City, Utah, to Reno, Nev., passes through Ely. The altitude at the collar of the Emma Nevada shaft is 7117 feet. The surrounding hills are covered with a sparse growth of juniper, pinon, and mountain mahogany.

Jan 1, 1940

By Patrick Frenette

The Goldex Mine is an underground gold mine using a unique mining method where a single very large stope is being created. In order to maintain stability of the walls and roof of the stope which is 450m, 250m high and up to 120m thick, ore is left in the stope as long as possible and acts as backfill would do. At many occasions during the mining sequence, the walls will be exposed on height ranging from 30 meters up to 250 meters. A monitoring system comprising in-stope laser surveys, a seismic system and an array of extensometers and sloughmeters all remotely connected to surface is used to observe the shape and evolution of the stope. This paper will focus on the results obtained following some of the large blasts and on the long term monitoring of the stope.

May 1, 2011

By Jeffrey A. Schaefer

The Olmsted Locks and Dam project is located on the Ohio River approximately 16.5 miles upstream of its confluence with the Mississippi River. It consists of twin 1200 ft. locks with floating and fixed approach walls, five 110 ft. wide tainter gate bays, a 1400 ft. wide navigable pass boat operated wicket gate section, and a 400-ft. section of fixed weir (Fig. 1). The project will have a total cost over 1.0 billion dollars, and as such is one of the largest civil works project underway in the Corps of Engineers.

Jan 1, 2001

By Alphonce Wikedzi, Mussa D. Budeba, Samwel V. Manyele, Sospeter P. Maganga

The present study provides an overview of the challenges and opportunities in processing complex gold-copper ores. The systematic literature review was conducted using Scopus database and seven-step methodological approach. The study indicates that the major challenges in processing complex gold-copper ores through the conventional cyanidation method include (1) increase in cyanide consumption; (2) increase in cyanide destruction cost; (3) low gold recovery; (4) decrease in adsorption efficiency; (5) decrease in electrowinning efficiency, and (6) difficulties in the measurement of free cyanide concentration in the leaching system. Moreover, the study indicates that several methods have been developed and some have been implemented in the mining industry for processing complex gold-copper ores. This includes ore segregation, pre-aeration, pre-treatment methods (e.g., ammonia), alternative lixiviants (e.g., thiosulfate, thiocyanate, glycine), cyanide destruction methods, and cyanide and copper recovery technologies. The study concluded that using lixiviant mixtures (e.g., cyanide-glycine), pre-treatment with environmentally friendly reagents (e.g., glycine) and the integrated membrane-based process (SuCy process) are new directions in processing complex gold-copper ores. However, more investigations are required to advance these processes to a commercial scale.

Sep 30, 2023

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

A pyrite flotation concentrate assaying 0·065 oz/ton gold was investigated to determine the mode of occurrence of the gold. Ftom cyanidation and acid leaching experiments it was concluded that O· 02-0· 03 oz/ton goldwas in solid solution in pyrite and the balance of the gold was finely dispersed as grains throughout the pyrite.Autoradiography and electron-probe examination of possible areas in briquetted concentrate did not detect any grains of gold. Neutron irradiation and gamma spectrometry confirmed on 100 mg samples the fire assays obtained on 1 assay ton samples.Oxidation to hematite and reduction to magnetite at 600°C made practically the whole of the gold extractable by cyanide. This technique could be of major significance for gold ores which contain a substantial amount of "refractory" gold.

Jan 1, 1969

By R. S. Dean

In addition to the normal work and that pertaining to strategic minerals, the Metallurgical Division has been made responsible for carrying on major investigations in the development of processes' for the treatment of low-grade domestic manganese ores that heretofore have failed to yield products suitable for the preparation of ferromanganese, an alloy essential to every ton of steel produced. These investigations are particularly important at this time because of their part in tucking this country self-sufficient with regard to manganese when the stock-piled ore becomes e exhausted and as foreign shipments of ferro-grade ore are cut off. The results indicate that there is a good probability of accomplishing this objective, while at the same time conservation may be promoted through the use of normally useless material from the large, low-grade ore deposits.

Jan 1, 1941

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By T M. El Hajj, A C. Chieregati, M T. G C Marques, J M. Braga Jr, H Delboni Jr

"The estimate and control of sampling errors is essential for all mining operations, especially when dealing with strategic materials, such as niobium. This paper is based on a traditional quality assurance and quality control technique used to confirm mineralised intersection zones, and proposes the validation of sampling data using diamond drill twin holes, in order to evaluate and improve the quality of the current data set. The geological model of the niobium mine – located in Araxá, Minas Gerais, Brazil – was built including 77 diamond drill holes of a sampling campaign carried out during the 1970s. There are few records about the collection and preparation procedures of these past samples, making it difficult to estimate the errors associated with their analytical results. Therefore, 11 twin drill holes were drilled to compare their samples against the samples from the 1970s drilling campaign. The new hole locations were chosen as near as possible to the old holes location. The JORC Code, 2012 edition, relates the use of twin holes as a good sampling technique to assess sampling and assay data. Three parameters were considered to validate the 1970s drill hole campaign by the twin drill hole campaign: the difference of the coordinates between the paired holes the difference among the positions of the geological contacts to validate the geologic description the difference between the paired samples grades was calculated to validate the analytical results.The analysis of the grade range variation between sample pairs was based on three techniques: geostatistical interpretation of vertical semivariogram to obtain the nugget effect calculation of the relative difference between duplicates calculation of the error associated with the sampling protocol established according to Pierre Gy’s Theory of Sampling.The results were satisfactory for hole coordinates; however, the ore content showed a high deviation, although this divergence can be explained by the nugget effect. For the lithological intervals, the new results contributed to an effective identification of variations among lithologies, ie brown weathered ore and saprolite. The twin drill holes campaign successfully validated the geological model data, allowing effective mine planning and higher reliability of the reconciliation results.CITATION:Marques, M T G C, El Hajj, T M, Braga Jr, J M, Chieregati, A C and Delboni Jr, H, 2017. Theory of Sampling and geostatistics for twin drill holes analysis in a niobium mine in Araxá, Brazil, Australia, in Proceedings Eighth World Conference on Sampling and Blending, pp 97–106 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017