Search Documents

By M Korte, J McMaster, C Brent

The Barrick Osborne concentrator has gone through a number of upgrades since commissioning and has increased production from the original 119 t/h design capacity to a milling throughput of 265 t/h in 2008. This was achieved incrementally over several years, by maximising operating efficiencies, in order to minimise capital expenditure, and take advantages of economies of scale; but more importantly it was reached with no measurable loss of recovery. Osborne currently processes a blend of underground and open pit material from the nearby Trekelano deposit. Following primary/secondary crushing, the material is processed through a rod/ball mill grinding circuit ahead of rougher/scavenger flotation that produces a copper concentrate. Osborne was seeking a further increase in plant throughput of the order of 15 per cent, but at more sustainable levels of secondary crusher plant utilisation. In early 2008, Osborne contracted Metso Process Technology and Innovation (PTI) to review the entire process from run-of-mine feed to final copper concentrate. This review would be done concurrently with surveys of both the crushing/grinding and flotation circuits being performed at the same time. The outcome would be a steady-state model of the complete flow sheet allowing the crushing/grinding model to interact with the flotation circuit model, such that overall process optimisation was possible. This was to apply both by exploring the operating limits of the currently installed plant, as well as looking at the logical next stage of capital plant expansions. Surveys of the crushing and grinding circuits were conducted at the Osborne concentrator in May 2008. The main objective of the surveys was to review the potential of increasing grinding throughput whilst maintaining the flotation feed 80 per cent passing size. This would also require improving the efficiency of the crushing circuit which was already operating in excess of 80 per cent of the time. Steady-state simulations were performed using the developed circuit models to identify opportunities to increase throughput and alleviate high circulating loads in both the secondary crushing and grinding circuits. Due to operational changes, the recommendations resulting from this project were considered by Osborne but have as yet only been partially implemented.  This paper covers part A or the crushing and grinding component of the project. A separate paper discussing part B or flotation is also being presented at this conference. The results of interactive simulations between the flotation and grinding circuit models are included in part B of this paper.

Jan 1, 2009

By Pieter Steeneklm, Mazi’ Rejaee

"EXECUTIVE SUMMARYThe automotive industry's search for increased fuel efficiency through component weight reduction has driven the growth in consumption of magnesium metal in the form of die cast alloys. This trend, which began in North America and should soon accelerate in Europe, will require enhanced recycling services since each tonne of metal used for die cast parts production produces about 500 kg of scrap.Currently, the European die cast market is plagued by very high tolling prices for scrap recycling due to lack of competition and high transport costs due to the distances between the scrap generator and the recycling facility. This situation clearly increases the cost of magnesium die cast components and reduces magnesium's competitiveness with other materials. The challenge for the magnesium industry in the short term is to provide cost ·effective recycling solutions for the die cast industry. In addition effective recycling, in the medium to long term, is needed for the anticipated large volumes of secondary or used scrap that will become available as the die cast components reach the end of their life cycle. This paper will present The Antheus Integrated Magnesium Project as a Novel approach addressing some of the key recycling related issues facing the magnesium industry, in particular the die casters. The paper outlines the many advantages of an integrated magnesium metal park, in an overall goal of increasing magnesium metal's competitiveness."

Jan 1, 2000

By Alastair Torrance, Mitchell Nipperess, Andrew Olsson, Italo Onederra, Gary Cavanough

Components of bulk explosive products include ammonium nitrate, water, fuel, stabilizers, and calcium nitrate. The physical attributes include prill/emulsion ratio, density, and viscosity and in the case of prilled ammonium nitrate, hardness, size distribution and fuel oil absorption. These components and attributes in conjunction with ground conditions determine all aspects of explosive performance including the risk of fume. This paper presents a fume risk assessment matrix of explosives components and physical attributes as a function of a simple description of ground conditions. Instrumentation to provide a measure of the quality of the explosive product are also described and these include both “on bench” physical measurements and laboratory analysis. “On bench” methods include “in hole “density, velocity of detonation (VOD), detonation pressure and detonation temperature. Part of the quality control process involves a mobile laboratory unit which at this stage can provide measurements of water content, ammonium nitrate content, calcium nitrate content, fuel content, prill characteristics and prill/emulsion ratio. This unit can be taken to sites to enable the testing of bulk and sensitized products at site rather than after transportation.

Jan 1, 2015

By Jack L. Henry

The monocarbide region of the ternary system U-C-O has been investigated at 1,700° C as the first phase of a more extensive study of a portion of the four-component system U-C-O-N. An area bounded by the following compositional limits in atomic percent was studied: U, 44 to 55; C, 30 to 60; 0, 0.2 to 20. Compacts composed of mixtures of uranium, graphite, and uranium dioxide powders were sintered at 1,700° C under an equilibrium pressure of carbon monoxide to produce uranium oxycarbide specimens having a variety of compositions. Sintered specimens were evaluated by X-ray, chemical analysis, and ceramographic techniques. Solid-solution boundaries and phase relations have been established, and the effects of composition on the lattice parameter as well as the decomposition pressure have been investigated. Oxygen can be substituted for carbon in stoichiometric uranium monocarbide to the extent of about 17 atomic percent at 1,700° C. The composition range of the oxycarbide solid solution extends from about 48 to 51 atomic percent uranium in the low oxygen region. Above 10 atomic percent oxygen the composition range narrows to less than 1 atomic percent uranium. Carbon monoxide exists as a gaseous phase in equilibrium with all compositions which contain oxygen. Five separate phase fields were found bounding the solid-solution area. Other phases within this portion of the system include uranium, uranium dioxide, uranium dicarbide, and uranium sesquicarbide. Decomposition pressures of oxycarbide compositions at 1,700° C have been found to vary from a few microns for stoichiometric and uranium-rich compositions to 35 torr for carbon-oxygen-rich specimens. Lattice parameters were found to depend upon the U to C + 0 ratio as well upon the extent of substitution of oxygen into the stoichiometric monocarbide lattice.

Jan 1, 1967

By Seth C. Schaefer

As part of the Bureau of Mines, U.S. Department of the Interior, effort to provide thermodynamic data for the advancement of minerals technology, the Gibbs energy of formation of sphalerite (zinc sulfide) was investigated with a high-temperature galvanic cell employing stabilized zirconia as the electrolyte. In the temperature range 948 to 1,210 K, potential measurements were obtained for the cell Pt, ZnS + ZnO, S02 = 1 atm // Zr02 // Cu20 + Cu, Pt, with the overall cell reaction ZnS(c) + 3 Cu20(c) = ZnO(c) + 6 Cu(c) + S02(g). (1) These results, combined with the best available values of ?Gf° for ZnO, S02, and Cu20 from the literature, give the Gibbs energy of formation of zinc sulfide for the reaction Zn(l,v) + 1/2 S2(g) = ZnS© (2) ?Gf° = -64.223 + 24.02 X 10-3T ± 0.650 kcal/mole (3) (948-1,180 K; standard states - pure liquid zinc and S2 gas at 1 atm), and ?Gf° = -92.720 + 48.17 X 10-3 ± 0.650 kcal/mole (1,180-1,210 K; standard states - pure zinc vapor and S2 gas at 1 atm). A third law analysis yields for the formation reaction Zn(1) + 1/2 S2(g) = ZnS(c), (5) a standard enthalpy of formation as follows: ?Hf298.15 = -63.64 ± 0.700 kcal/mole.

Jan 1, 1978

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high-temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on-record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range. Low-temperature tars, on the other hand, are more complex, and hence exhibit dissimilarities from one to the next. Edwards, who has made a study of the acids, bases, and neutral oil of four low-temperature tar distillates, shows that the bases and neutral oil are evenly distributed among the fractions but that the concentration of the acids is greatest in the 200° to 230° fraction. Morgan and Soule find that in tar from the "Carbocoal" process, the 237° to 281° fraction has the highest acid content, whereas Davis and Parry find the 200° to 225° fraction of Freeport tar richest in phenols. Previous investigators have noted the following differences between primary and high-temperature tar: In the latter, naphthalene and anthracene occur in large quantities, the paraffins and naphthenes are negligible, the percentage of higher phenols is much lower than in primary tar, and the lower and more stable aromatic hydrocarbons have increased. In an endeavor to reconcile the change undergone when a primary is converted into a secondary tar, the writers have been unable to find references dealing with the extent of change which any one of the constituents of primary tar may undergo when subjected to secondary heating effects in the presence of other components, and the amount of the more stable compounds that may be expected from a given starting material.

Jan 1, 1932

By Anibal Gastañaga

La determinación del cuarzo es un problema dentro de la Higiene Industrial, puesto que este mineral se convierte en una de las enfermedades ocupacionales causadas por la inhalación de pequeñas partículas de cuarzo encontradas en el aire. En ese sentido, el presente texto señala la importancia y peligrosidad de los polvos del mineral a través de la determinación cuantitativa de cuarzo en los polvos industriales, ya que el riesgo de adquirir silicosis es proporcional a la concentración de cuarzo en los polvos ambientales. Existen tres métodos para la determinación cuantitativa de cuarzo: El método químico, el de difracción de rayos X y el petrográfico. El método que presenta mejores beneficios es el de N. A. Talvitie, puesto que se basa en la propiedad del ácido fosfórico, donde se forma complejos solubles en agua con los silicatos y óxidos metálicos, quedando el cuarzo prácticamente inalterado.

Aug 1, 1955

With the advent of the environmental "green" movement of the 1960s, eventually leading to Earth Day 1970, Congress responded by passage of the National Environmental Policy Act (NEPA), 1970. NEPA gave impetus to a flood of federal acts and laws in the subsequent three decades. Many of those protecting man's environment, health, and well-being also affect mining. For purposes of this chapter, a current mineral law summarization lends itself to a division into two parts: viz., Part I, General Mining Law, and Part II, Enviromining Law. The word enviromining has been coined by the author and is defined and used herein as those federal and state statutes and regulations that were created to provide protection and preservation of man's environment, health, safety, and welfare, and they have particular application to and affect on mining activities. They are listed and treated under Enviromining Laws in Part II. Mining, as a basic industry to provide the essential minerals for mankind's necessities and well-being, truly reflects the mining industry's slogan, "If it can't be grown, it must be mined." Without the basic minerals and rocks won from the earth by mining and mineral processing for their valuable physical properties or chemical constituents, man would soon be forced to revert to the cave-dwelling age. Unfortunately, for man to survive in the "manner of life to which he has become accustomed," he is caught between the demands of cleaning up his deteriorating environment and a continued supply of his basic requirements and amenities for daily living supplied by mining of the earth's minerals. He must have "clean living" at the same time with "good living;" neither is expendable. A very high pricetag accompanies this essential and critical choice which must be paid by society. The United States is internationally recognized as the world leader in environmental matters. Many countries are following suit, principally the other Anglo nations. Because US law is founded and based on English law, on occasion, Anglo-American law is referred to and cited as authority in litigation anywhere in the Anglo-American world of jurisprudence. For this reason, and because mining and the industry is international in nature and operations, some British Commonwealth cases will appear in various topics. If the case is of interest to the reader, further inquiry at a law library may be made through use of the case's style and citation given. "Style" refers to the name of the litigating parties. "Citation" refers to the law publication in which the case and decision may be found, as well as the jurisdiction and court of decision. Citation of cases from the United States and British Commonwealth nations is explained under Case Citation Explanation. Space and time limit exhaustive treatment of subjects and covering all geographic and jurisdictional areas. This chapter is intended as a broad outline and is based on the author's master's thesis at the University of Missouri-Rolla, 1992. The following Case Citation Explanation provides guidance on formatting of citations.

Jan 1, 1994

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By R. H. Richards, A. E. Woodward

In Rittinger's Aufbereitungskunde of 1867 occurs (p. 195) the following table, which shows the rate of falling in water of fragments of minerals, of irregular shapes and of five different specific gravities: Diameter of particles in millimeters. 10 8 6 4 3 2 1 .5 Sp. Or. Velocity in meters per second. Auriferous silver, 16..9 .8 .7 .57 .5 .4 .29 .20 Galena,. ..7.5 .62 .55 .48 .39 54 .28 .20 .14 Pyrites,. ..5.0 .49 .43 .38 .30 .26 .22 .15 .10 Quartz,. ..2.6 -30 .27 24 .19 .17 .14 .10 .07 Coal,. ..1.3 .13 .12 .10 .08 .07 .06 .04 .03 With the purpose of extending this valuable table, to cover a larger number of minerals and sizes of each mineral, and of making it more easy of application in deciding upon a sieve-scale for any group of minerals, we have prepared the curves of velocity of fall of bodies in water shown in Plates I., XI., 111. and IV., using Rittinger's formula V= 2.44d(8 —1) where V= velocity in millimeters per second. " D = diameter of particles in meters. " 8 = specific gravity of the mineral. These curves embrace a large number of specific gravities, and for each specific gravity the relation of the diameter of the mineral particle to the velocity of its fall in water is given for all diameters and velocities used in practice. The second diagram is an enlargement of the lower left-hand corner of the first, the third bears the same relation to the second, and in like manner the fourth to the third. Plate I, therefore, covers the work of the coarsest jigging 2 inches in diameter; and under

Jan 1, 1890

By Sir Stopford Brunton

Gold was first found in Nova Scotia about 1830-40, but its significance at that time was not appreciated. Probably the first discovery that resulted in any work was made by Lieut. C. !'Estrange, at Mooseland, on the Tangier river, in 1858.1 Since that time gold has been mined with varying success until now, and from 1868 onwards work has never altogether ceased. Gold mining in Nova Scotia is at the moment under a cloud, and the idea generally accepted by most people is that it has failed in the past, and that there is no prospect for it in the future. The actual reasons for the present situation have never been carefully analysed, and it seems a good thing to see what really is the state of the case and whether or not this general idea is worthy of credence. It is the purpose of the present paper to analyse the situation in the light of present knowledge, and to set forth some data which may assist in the future development of the Province.

Jan 1, 1926

8053. Andreev, B. A. Zakashanakii, M. S., Samsonov, N. N., and Fotiadi, E. E. A Textbook of Gravitational -Surveying, (in Russian). Gosgeolizdat, Moscow-Leningrad, 1941, 432 pp. This textbook was written at the suggestion of-the faculty of geophysical exploration of the Leningrad Mining Institute. It contains two parts: (1) Theory and technique, and (2) Applications to geology and exploration. The features bringing; the text up-to-date include: (a) Description of the principal modern gravimeters; particular attention to the method of simultaneous oscillation of 4 pendulums; (b) discussion of the aperiodic oscillation of torsion balances; outline of the construction of variometers Z -20 and Z-40; (c) material for aid in interpretation, such as reference-charts, formulas with their derivation, atlas of theoretical curves, and examples of interpretative calculations; (d) considerations in the planning of surveys and the densities of various rocks; and (e) detailed analysis of significant examples. The text is provided with a bibliography, V. S.

Jan 1, 1946

By Paul M. Tyler, Colin G. Fink

THE field of rare metals is so broad that progress can be reported upon many important fronts. Not satisfied with the 92 elements that Mendeleeff and his followers have accepted as legitimate, scientists are trying now to complicate matters by making new elements. Enrico Fermi announced the fabrication of "Element 93". Uranium, instead of being allowed to disintegrate slowly according to its normal habit, was bombarded with neutrons until some of them seemed to have stuck in the nucleus. To understand just what is alleged to have happened all one has to do is to line up the elements in their usual order of ascending atomic weight and imagine, as physicists do, that each atom is a little solar orbit comprising a central mass or planet about which other masses revolve like satellites. Ordinary hydrogen, being very light, consists of only one positively charged proton center, with only one positively charged electron revolving about it. Other atones are progressively more complicated until we come to uranium, which has a relatively big center and 92 particles revolving around it.

Jan 1, 1935

By M. Salimov, J. Sattarvand

The conventional visualisation method of remote equipment is through the installation of one or more cameras on the machine, and sending a live feed to the operator’s flat display. However, the performance of the teleoperation can be enhanced using better visualisation through virtual reality (VR). This paper presents the process of the design and manufacturing of a robotic platform that will be used in the next phase of the project for a VR-assisted teleoperated excavator. The robot consists of a loading boom and arm arrangement installed on the undercarriage of a CAT300-9D. All hydraulic cylinders are replaced with electric actuators, and crawling motors are substituted by electric motors. The pieces of the boom and the arm, as well as the bucket were designed in Autodesk Inventor, and manufactured from aluminium sheets using a desktop and CNC machine. Parts are joined by pins and welding as needed. An Arduino-based control system is developed for the robot, and motor controllers are used to convert the power commands from the microcontroller to the high-amperage actuators. The control system is capable of communicating with a wireless Play Station controller to operate remotely. The manufactured robotic excavator is planned to be utilised in multiple autonomy research projects.

Sep 1, 2021

Introduction to high temperature oxidation of metals, by N. Birks and G. H. Meier, London, Edward Arnold, 1983. 19S pp. R30,25. Reviewers: M. B. Cortie and G. G. Garrett Seam gas drainage with particular reference to the working seam, edited by A. J. Hargraves. Woollongong, The Australasian Institute of Mining and Metallurgy. 370 pp. $A30. Reviewer: C. J. Fauconnier New books Solvent extraction Part I, by G. M. Ritcey and A. Ashbrook. Amsterdam, Elsevier, 1983. Elektronishche Steuerungen und Mikroprozessoren im Bergbau. Sicherheit und Zuverlassigkeit Environmental impact control. Philosophical and procedural guidelines for the planning professions Mineral processing and extractive metallurgy. Reagents in the minerals industry.

Jan 1, 1984

By J. Muralha

The paper presents the limit equilibrium equations for the analysis of toppling blocks on a rock slope. The safety conditions are assessed by a numeric procedure implemented in an Excel worksheet. The UDEC numerical program was exploited to validate the procedure. A probabilistic model considering the spacing variability of the discontinuities was developed to define the most relevant parameters in this kind of problems. La communication presente les equations d’équilibre limite pour l’analyse de blocs rocheux sur une pente. Les conditions de securité sont évaluées par une procédure numérique en Excel. Le logiciel UDEC a été exploité pour valider cette procedure. Un modèle probabilistique a été developpé pour définir les plus importants paramètres dans ces problèmes. Das Referat stellt die Grenzgleichgewichtsgleichungen für die Analyse von umstrürzenden Blök-ken auf eines Felshang vor. Die Sicherheitsbedingungen werden durch ein numerisches Verfahren mit Excel beurteilt. Um die Gültigkeit des Verfahrens festzustellen, wurde das Programm UDEC benutzt. Ein die Klufabstandsvariabilität berücksichtigendes probabilistisches Modell wurde entwickelt, um die wichtigsten Parameter dieser Probleme zu bestimmen.

Jan 1, 2003

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high- temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols4 it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range.

Jan 1, 1932

By W. G. Lidman, H. J. Hamjian

' I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:' the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F') at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.' Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

Studies were carried out to examine the effect of introducing varying levels of a pisolitic limonite (Yandi) into an Australian iron ore blend. Compared with other ores in the blend Yandi is more porous. This structure is found to have a considerable effect on the sintering behaviour of the blends. Pilot-scale sintering studies and plant trials showed that sinter plant productivity, sinter reducibility and the low-temperature reduction degradation index altered significantly when the level of Yandi in the ore blend exceeded 15 wt%. The improvement in the reducibility is thought to be a direct result of increased porosity in the sinter and the presence of highly reducible pseudo-relict haematite. Plant trials have also shown that operational changes could be made to the sinter plant to avoid potential deterioration of productivity

Dec 1, 1991

By Paul Cameron Gilmour

Geologically, as distinct from economically, "porphyry copper (molybdenum, gold, silver, etc.) deposits" might be defined as large, disseminated and/or stock-work occurrences of copper-minerals, generally averaging less than 1 per cent cop-per. They are normally associated with small plutons which range in composition from granite to diorite, although, typically, they consist of quartz monzonite or granodiorite. Circumstantial evidence indicates that these "minor" granitic intrusions may represent the intrusive phases of post-orogenic, calc-alkaline volcanism, this conclusion being suggested by: 1. Texture and grain size. 2. Prevalence of intrusive breccias. 3. Relationship to unconformities and estimated depth of emplacement. 4. Spatial distribution in relation to orogenic zones. 5. Age of mineralization and igneous episodes

Jan 1, 1972