Search Documents

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By Charles S. Spirakis

The consistent occurrence of organic carbon early in the paragenesis of Mississippi Valley-type sulfide deposits suggests a genetic link between organic carbon and the sulfide ores. Reduction of sulfate in the mineralizing solution by organic carbon at the sites of mineralization is commonly proposed as the precipitation mechanism for these deposits, but inorganic sulfate reduction is too slow to be important to the chemistry of the ore zone, and bacteria, which catalyze sulfate reduction at low temperatures, are not known to survive at the temperatures of mineralization. Sulfate reduction with or without bacteria is not consistent with the sulfur Isotope evidence. Sulfur isotope studies also indicate that the derivation of sulfur from hydrocarbon at the sites of mineralization is unlikely. Organometallic complexing may be involved in the transport of metals, but no plausible mechanism for breaking these complexes at the sites of mineralization has been proposed. Reduction of partly oxidized sulfur species in the mineralizing solution by organic carbon at the sites of mineralization is a possibility which deserves further scrutiny.

Jan 1, 2013

By Thomas A. Printz

The wide use of carbon steel in construction and engineering projects makes this engineering material accountable for approximately 85% of the total annual steel production worldwide. Despite the lack of corrosion resistance of carbon steel, it is incorporated into the permanent work for marine applications, power plants, transportation projects, chemical processing, mining, petroleum production and refining, pipelines, mining and construction equipment. Corrosion is an electro-chemical process that occurs in the presence of water and air. When an electric current is introduced to water or soil, the rate of carbon steel corrosion increases rapidly. Gaseous atmospheric constituents that are capable of electrolytic activity can also increase the rate of corrosion. Corrosion tends to be more rapid in environments in which the steel is exposed to water, and then air, rather than being constantly submerged. The exposure to seawater increases steel pitting because the electrical conductivity is improved in salt water.

Jan 1, 2013

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"A ceramic body traditionally used to produce bricks and roofing tiles with kaolinitic clays was reformulated by the addition of sand and illitic clay. The objective was to obtain a ceramic product with better technological properties. Specimens were made by uniaxial press-molding at 20 MPa and then fired at 850, 900 and 950°C. The determined technological properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that both sand and illitic clay contribute to reduce the water absorption of the industrial clayey body. With respect to the flexural behavior, it was observed that the incorporation of sand decreased the mechanical strength. On the other hand, the illitic, incorporated in an amounts of 30 wt.% contributed to increase the mechanical strength of the clayey ceramic.IntroductionCeramic bodies industrially fabricated in the county of Campos, north of the State of Rio de Janeiro, in Brazil, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral in nature, associated with high plasticity and elevated weight loss during the firing stage. Due to the excessive plasticity of the ceramic bodies, dimensional defects, which occur after drying and firing are usually obtained. Moreover, the kaolinitic nature and the presence of aluminum hydroxide (gibbsite) confer a refractory behavior to the local clays, which impairs sintering during the firing operation. In the case of clay ceramic products for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [1,2]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative.As an alternative to reduce the plasticity of clayey ceramics sand, which is predominantly constituted of silica, can be used. The incorporation of sand in amounts of up to 25 wt.% to a clayey ceramic body used for roofing tiles fabrication was studied by Vieira et al. [3]. In that work specimens were prepared by extrusion and fired at 850°C. The results indicated that in the pre-firing stages the sand improved the workability of the investigated clayey ceramic body and facilitates the drying stage. It was also observed that the incorporated sand significantly improved the physical and mechanical properties of the clayey ceramic after firing. On the other hand, the apport of flux oxides could be done by the use of illitic clays that have a higher amount of alkaline oxides in comparison with the kaolinitics clays."

Jan 1, 2013

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Jilai Xue, Jun Zhu, Germain Kouma Ndong, Qiaochu Liu, Luxing Feng

"High-temperature oxidation and corrosion behaviors of Ni-Fe-Cr alloy as inert anodes for aluminum electrolysis have been studied in oxygen and molten electrolyte. The oxidation and corrosion scales on the anodes tested were analyzed using XRD and SEM-EDS. The oxidation rate is found to increase with increasing temperature from 700 °C to 950 °C, which can be approximately described by an inverse power rate function. The oxidation scales at 750 °C, 920 °C and 950 °C contain Cr-rich phase along with FeCr204 and (Feo.6Cro4)203. The corrosion extent of Ni-Fe-Cr anodes in electrolyte is dominated by temperature, which can make the scales thickness double from 700 °C to 750 °C or from 920 °C to 950 °C. Cr and Fe in the scales on the anode in electrolysis corrode preferentially into the molten electrolyte, while the nickel oxides could better sustain the corrosive environment in electrolysis. The results can be useful for developing inert anode material for potential application in aluminum electrolysis.IntroductionThe development of an inert anode for aluminum electrolysis has been a long term goal for aluminum industry. The present process for primary aluminum production involves the reduction of alumina with carbon anodes, forming carbon dioxide:"

Jan 1, 2013

By A. Butler

This paper explains the politics of mine nationalization in contemporary South Africa. Nationalization and privatization typically occur in the oil, mineral resources, and state utilities sectors, and they tend to follow one another in a long-term cyclical pattern. The paper explains why the current international environment has encouraged demands for nationalization and other forms of ?resource nationalism? in the South African minerals sector. It goes on to describe how the resurgence of resource nationalism has been influenced by internal factional politics in the African National Congress. It concludes that nationalization is unlikely to be the outcome of current policy deliberations within the ANC.

Jan 1, 2013

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modeled with conditional simulation, which generates multiple possible realizations of grade that are equally probable (or improbable). M ethods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time-consuming. This paper proposes a simple and efficient modeling approach to incorporating conditional simulation into pit optimization, which would be able to be applied in currently commercially available software. An example for R esolute M ining Ltd.?s Syama gold project in M ali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Jan 1, 2013

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By Patrick G. Hatcher

Studies of sedimentary humic acids by nuclear magnetic resonance (NMR), stable isotopes, and elemental analysis show they are derived by oxidative degradation of complex plant macromolecules that are insoluble in aqueous or organic solvents. The mechanism by which humic acids originate is fundamental to our understanding of the role of organic matter in ore deposition, because these substances can complex and mobilize a number of metal ions. The organic matter associated with uranium ores of the San Juan Basin, New Mexico and Carlin-type disseminated gold deposits of Nevada has certain organic geochemical characteristics that suggest an origin from humic acids.

Jan 1, 2013

By Alice Barreto Bevitori, Frederico Muylaert Margem, Noan Tonini SImonassi, Caroline Oliveyra, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The mechanical behavior and the fracture characteristics of composites with DGEB/TETA epoxy matrix reinforced with up to 30% in volume of continuous and aligned ramie fibers were evaluated by tensile tests. Specimens with selected thin fibers aligned along the tensile axis were room temperature tested to rupture. The fracture surface was analyzed by scanning electron microscopy. The results showed significant increase in both the ultimate tensile strength and the elastic modulus. The fracture analysis indicated the possible mechanism for the fiber/matrix interaction, which could be responsible for the composite performance.IntroductionSince the middle of last century, polymer composites have substitute many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffuess requirements that could be reached with synthetic fibers such as gloss, carbon and aramid fibers. Its most commonly used example is ""fiberglass"", i.e., a thermoset polymer matrix composite reinforced with glass fiber. Indeed, ""fiberglass"" has a specific strength of the order of 500 MPa.cm3/g, which is the double of the strongest steels like the maraging. This motivated, at earlier times, ""fiberglass"" to replace many conventional materials including wood and natural fiber composites. Today, ""fiberglass"" has a wide range of uses from aerospace systems and appliances to sport and leisure components. However, its fabrication as well as those of any synthetic fiber such as carbon and aramid composites, requires a relatively large amount of energy. Presently, a growing concern exists regarding the consequences to the environmental by gases like C02 associated with both the energy consumption and the processing of synthetic fibers and their composites. These gases are well known responsible for global warming [3]."

Jan 1, 2013

By Mark Alan Marlkos

Blebs of solid bitumen from the Magmont West orebody of the Viburnum Trend were examined and analyzed in an attempt to relate hydrocarbon distribution and origin to ore genesis. The bitumen was calculated to be approximately 48 to 63 percent aliphatic and is considered to be a polymerized normal crude oil. Polymerization, which was probably caused by water-washing, hardened the bleb surfaces and appears to have "frozen" the blebs during primary migration from local source beds. Comparison of the bitumen to kerogen in local shaly partings strongly Indicates that the oil was derived locally. The polymerized oil blebs are considered to have been derived from a type II (marine) kerogen. Textural analyses indicate that oil migration occurred after lead-zinc mineralization and at temperatures that exceed normal ancient or present geothermal gradients. The following sequence of events is postulated for the Magmont West orebody: 1 Generation of hydrogen sulfide during diagenesis of a normal organic-rich carbonate sequence. 2 Introduction of pulses of hot, metal-rich fluids that resulted in: a Lead-zinc mineralization by the following reaction: Me++ + H2S ? MeS + 2H+ b Solution of carbonates by excess acid produced during the above reaction. c Brecciation of host rock in some cases. 3 Passages of the pulse resulted in: a Carbonate buffering of fluid system to more alkaline conditions. b Precipitation of dolomite c Slight temperature drop. 4 Eventually the high temperatures Introduced by heated brine caused oil generation and initiated primary migration. 5 Water-washing and mild biodegradation altered the hydrocarbon blebs to their present composition.

Jan 1, 2013

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By N. Shi, T. G. Joseph

ABSTRACT Before any large plant is moved onto an oil sands dominated surface, particularly those surfaces encountered in-pit, it is imperative that the ground be evaluated for bearing capacity. A 2230 tonne mobile in-pit hopper/crusher facility designed for operation in the Canadian oil sands was modeled. This evaluation focused on track and outrigger pad versus ground interactions as the key performance indicators of appropriate ground performance below the unit in both operating and repositioning propel modes. A study of cyclic oil sand behaviour was also inferred from laboratory cyclic plate load data as an extension of the simulation model indications.

Jan 1, 2013

By Onuralp Yiicel, Ozlem Okur, Murat Alkan

"In this study, Co-Cr-Mo alloys were produced using a mixture of Co304, Cr203 and Mo03 powders with Al powders by a Self-propagating high temperature synthesis process. SHS is a process of material synthesis that has revealed a number of reactants combinations capable of much higher energy release than conventional explosives. Al203 is added to the mixture to decrease the adiabatic temperature of the system. The thermodynamic simulations and the calculations of adiabatic temperature were examined with FactSage 6.2. In the SHS experiments, different Co304/ Cr203/Mo03 ratios were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis, XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Co-Cr-Mo master alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013