Search Documents

By J. McKelliget, J. Szekely, Oreper. G. M.

"1. INTRODUCTIONThis paper is concerned with heat and fluid flow phenomena in arc welding operations. Fig. 1 shows a schematic sketch of a typical arc welding arrangement. It is seen that an arc is being struck between an inert electrode and a metal surface and that the resultant current and energy flow will case the formation of a molten weldpool.It is clearly appreciated that the weldpool shape and the nature of circulation in the weldpool may play an important part in determining the ultimate weld quality. It is known, furthermore,· that the weldpool behavior in turn will be affected by the spatial distribution of the current and the heat flux it receives from the arc. Indeed, the inherent coupling between the arc and the weldpool is a key feature of welding operations.Up to the present useful work has been done on the modelling of heat transfer and melt circulation in weldpools (1,2,3,4) and also on the description of arcs, including welding arcs (5,6,7,8). However, the coupling between these two sets of phenomena is relatively unexplored in a qualitative sense. The purpose of the present paper is to examine the interaction between welding arcs and weldpools. The actual material will be presented under the following headings:"

Jan 1, 1986

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By Cody Burcher-Jones

The recovery of rare earth elements (REEs) through heap leach/in situ techniques from so-called ion adsorption clays (IACs) is attractive due to their inherent simplicity. However, the underlying mechanisms of these processes are poorly understood. In this study, the deportment of REEs in a typical IAC material has been investigated and was found to concentrate in the phyllo-layers of the clays, especially hallyosite, and was readily desorbed by various ion-exchange reagents indicating various potential routes to liberate them. Here we are reporting the use of seawater (0.5 M NaCl), spiked with various amounts of (NH4)2SO4, and found better extraction using a reagent mixture than NaCl on its own. Further, the leaching of REEs from a bed of clay material was investigated over time to understand the rate of transport through the stagnant material. Results indicate that REE release is likely to be controlled by diffusion through the clay material, while desorption in agitated systems is rapid. A degree of fractionation between different REEs can be observed during diffusion. Nonetheless, the successful operation of in situ leach operations for this type of material would depend primarily on how easily solution cocktails can be made to flow through the bed material.

By J. E. Dutrizac

Mineralogical studies were carried out on nodulated copper cathodes from three primary refineries to characterize the nodular growths and to elucidate the causes of the nodulation. Nodulation is often initiated at the surface of the starter sheet or the stainless steel plating blank, although a layer of smooth copper sometimes is deposited before nodulation commences. In some instances, the "roots" of the nodules exhibit a pronounced dendritic texture that is associated with an abundance of cavities. Slimes particles are not usually associated with these growth features which lead to a globular surface deposit. The globules sometimes develop into larger nodules, and this type of nodulation is likely caused by improper addition agent concentrations. The nodules on most cathodes, however, exhibit "roots" at the contact with the substrate that are associated with microcavities and large clusters (>40 µm) of slimes particles. The slimes constituents are commonly Ag powder, PbSO4 and Cu2(Se,Te) but not AgCu(Se,Te) or Ag,(Se,Te). The size of the slimes clusters, rather than their composition, appears to be the important factor causing the copper to grow into nodules. Tiny individual slimes particles themselves do not appear to cause cathode nodulation.

Jan 1, 1999

By A. V. Tarasov

The nonferrous metals industry has been a sector with one of the highest growth rates during the recent years. The prospects for the Russian metals industry during the period until 2010 are associated first of all with a growing domestic demand for its products. The technological level of the metallurgical operations in Russia is relatively low in comparison with industrially developed countries: the average energy requirement is higher by 20% to 30%; the amount of generated waste in the process of rolled products manufacture is twice as high; the average labor productivity is lower by 2.5 to 3.0 times; the overall negative environmental impact is twice as high. Improvement of the technological level of the nonferrous metals production under the conditions of market economy is possible by application of innovative technologies for the development of this sector. The main trends for development of the nonferrous metals sector are: - meeting of more stringent requirements to the quality of concentrates; - more complete recovery of associated elements as commercial-grade products; - development of continuous process lines based on autogenous, resource-saving and environmentally safe processes; - use of combined technologies, including pyrometallurgical, hydrometallurgical and upgrading processes; - expansion of the fields of application for nonferrous metals and their alloys.

Jan 1, 2006

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2:1. The samples having the density more than 99% of the theoretieal value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical casting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the. oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By Girley Ferreira Rodrigues, Crocce Denise Romano Espinosa, Victor Bridi Telles, Eduardo Junca, Jorge Alberto Soares Tenorio

"Steel sector is responsible for the generation of solid waste, liquid and gaseous effluents. The Solid waste are mainly composed of slag, dust, sludge and scrap. The industry generates approximately 650kg of solid waste per tonne of steel. Approximately 10% of this waste is in the form of dust and mud. The basic oxygen furnace dust is a waste generate by steel sector. Each tonne of produced steel generates 10 to 20 kg dust. Thus, the aim of this paper is study the reduction of pellets made with BOF dust using hydrogen and study kinetic during the reduction. The tests were performed in a netzsch thermobalance to obtain the data of lost mass. This loss mass is coming from iron oxides present in the BOF dust.IntroductionThe generation of solid waste is a problem for many companies in the steel sector. The main solid wastes generated are slag, dust, sludge and scrap [1]. Beyond solid waste liquid and gaseous effluents are also generated.The basic oxygen furnace is responsible for 60% of all steel produced. This sector is the second largest generator of solid waste from an integrated steel mill, contributing with 27% of solid waste generated in a plant ( 5-7 million tons of waste generated annually worldwide) [2,3,4]."

Jan 1, 2013

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Paul Dewison

For nine years, from mid-1987 to mid-1996, the copper market enjoyed what appeared to be an endless boom in which prices were much higher relative to production costs than for most other base metals. After the boom ended abruptly mid-1997 with the Sumitomo affair, copper was burdened by an overhang of new projects that promised to swamp demand in what, with the Asian financial and economic crisis of 1997, had become a considerably worse consumption environment. Now, demand prospects do not look so bad. If, as we suspect, we will be dealing with a more rational market in the future, it becomes all the more important to forecast accurately the prospects for consumption. In this paper, we present a new methodology for copper demand forecasting. The methodology forms the backbone of the demand-side analysis for the multi-client study entitled "Long Tenn Outlook for Copper", co-authored by Metalica Ltd. and Bloomsbury Minerals Economics (BME). Key components of the methodology are as follows. (1) Relate demand to economic structure. (2) Focus on products rather than refined consumption. (3) Apply a consistent products/applications analysis to all countries and time series. (4) Incorporate scrap market dynamics within the analytical framework.

Jan 1, 1999

By Nils Eivind Kamfjord, Halvard Tveit, Ingeborg Solheim

"Because of its negative environmental effect the attention towards NO emissions increases. This again leads to new demands from the authorities for better surveillance and control of emissions. Earlier and recent industrial measurements towards FeSi- and Si-metal furnaces reveal quite high NO-emission. The NO is believed to be produced in the combustion zone above the furnace surface, mainly as thermal NO.In order to expand the knowledge on NO-formation in silicon metal production, a pilot scale experiment in a 440 kVA silicon furnace has been carried out. The experimental set-up was designed with a view to be able to copy and manipulate the formation mechanisms for NO by controlling the flow of false air into the off-gas system.The resulting NO-values corresponding to the different air inlet to the furnace top, show significantly differences between the different air inlet geometries.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2). Since combustion of fuels, such as gasoline, diesel, bio diesel, propane, coal, and ethanol, forms NOx the dominating contributors to NOx emissions are the on-/offshore transportation industry and power generation based on fossil fuels [1]."

Jan 1, 2012

By E. J. Peuraniemi

Recently commissioned Kennecott-Outokumpu flash converting was developed to replace the approved but environmentally outdated Peirce-Smith -converting to satisfy the globally tightening emission regulations. In the present study, dust formation and reaction mechanisms of two copper mattes with different experimental parameters were studied in lean suspension conditions. Both mattes had very high copper content of approximately 75 wt% and low iron content of 4.5 wt% and 1.2 wt% Fe. A laboratory scale, vertical laminar-flow furnace with a low feeding rate was used to simulate the phenomena taking place in the reaction shaft of a flash converter. Experimental conditions included temperature of 1300 °C with reaction gas oxygen contents of 20 vol%, 50 vol%, and 75 vol%. In the experiments, sieved particle fractions were fed to the furnace and sampled after short reaction time intervals by quenching them into a water film. Collected particles were analysed chemically for their main elements to define their removal rates. Also, optical and scanning electron microscopy with EDS-analyser were applied to determine phenomena occurring during reactions. Kinetics of oxidation as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are reviewed to describe dust formation and reaction mechanisms.

Jan 1, 1999

By Akira Yazawa

The composition of ferrous calcium silicate slag is located on the tie line between FeOx and calcium silicates in ternary FeOx-SiO2-CaO system. This slag has never been used as copper smelting slag because of high sulfidic copper solubility. However, when the dissolved copper in slag is just oxidic, as in direct white metal production or in converting process, this slag is quite attractive and can be regarded as the third copper smelting slag after fayalite and calcium ferrite slags. Based on the authors&apos; studies on phase separation thermodynamics and laboratory experiments, it was clarified that the oxidic copper loss in this ferrous calcium silicate slag become the minimum not only %Cu in slag but also the total copper loss when the amount of slag is taken into account. It has been proven that calcium ferrite slag is suitable for continuous converting where the dissolved copper is oxidic, but there exist some drawbacks such as limited solubility of silica, low lead removability and too high fluidity. To overcome these difficulties accompanying traditional slags, ferrous calcium silicate slag is the hopeful alternative. In view of the general trends of modem copper smelting processes, the interesting features of this new slag system are discussed.

Jan 1, 1999

By David Ellis

The next generation of Reusable Launch Vehicle (RLV) will utilize regeneratively cooled combustion chamber liners in the engines. The current design calls for using a new Cu-8 at. % Cr-4 at. % Nb (Cu-8 Cr-4 Nb) alloy for the liners. Work is ongoing to characterize the thermophysical and mechanical properties of the alloy from - 253 to 800°C, the temperature range to which the alloy will be subjected during service. The alloy has been commercially produced in quantity for NASA. The powder size has been characterized and the microstructure examined. The powder was extruded into bar using a commercial extrusion press. In addition, samples have been hot isostatically pressed (HIPed) at NASA Glenn Research Center. Both processing methods produced fully consolidated material. Transmission electron microscopy (TEM) revealed highly faulted Cr2Nb and some elemental precipitates. Cryogenic tensile testing showed the extruded specimens had significantly higher strengths than NARloy-Z (Cu-3 wt % Ag-0.5 wt % Zr) even after being subjected to a simulated braze cycle. The Young&apos;s moduli (Cu-8 Cr-4 Nb) were lower than NARloy-Z. The lower moduli is highly beneficial for reducing thermally induced stresses in rocket engine combustion chamber liners and similar applications.

Jan 1, 1999

By Min Zhu, Yu Ji, An-chao Ren

"After being welded in the weld plant, the 100-meter heavy rails with the specification of 60kg/m are found broken during the straightening process in four planes. Failure analysis is made using the optical microscope and SEM with the result showing that the broken rail contains the imperfection of protrusion which exists at the edge of rail foot, about 1 00mm away from the rail end. When the protrusion is peeled off by deseamer from rail surface, cold scratch is generated which causes the rail to be broken during the subsequent straightening process. By adjusting the roll diameter differences between top and bottom roll of universal finishing mill and the height of pass line, it is possible to maintain the rails flat when leaving the mill. This prevents the upsweep and downsweep phenomena and, thus, the imperfection of protrusion can be eliminated. IntroductionThe development of rail transit worldwide has entered into a new era since the 1960s. The hi-tech rail transit system has gradually gained recognition over the world. In particular, the emergence of new-type passenger trains represented by TGV of France, ICE of Germany and Shinkansen of Japan and heavy haul trains as well, has revealed the charming way and more prosperous future of the modern and hi-tech rail transit system to the people all over the world. It should be pointed out that rail transit system is still the most effective solution to traffic jams among urban cities and in the central cities during the 21 '1 century, especially high-speed railway and subway which take overwhelming advantages over air transport, marine transport and road transport in terms of high speed, high efficiency, safety, comfort, environment protection and high flow. With the trend of increasing speed and heavier load of trains, higher product quality of rails is demanded. The rails for passenger dedicated lines require high cleanness, high accuracy in size, high flatness, high surface quality and large size (100-meter fixed length). The rail quality has direct influence on the operating performance of rail and railway traffic safety. The 100-meter heavy rails with the specification of 60kg/m are broken subject to the straightening process in four planes after being welded in the weld plant. This paper analyzes the reason for rails being broken and provides the theoretical proof for determining the rolling process."

Jan 1, 2013

By Tracy Morris, Weldon Read, Luis Navarro

"Bismuth is a recognized contaminant in the electrolytic refining of copper that can render many cathodes to be outside ASTM standards and unsuitable for copper rod and other downstream products if not carefully controlled. This paper portrays the performance of Molecular Recognition Technology (MRT) for bismuth removal at the Amarillo Copper Refinery (ACR) and describes how the highly selectivity gel has been successfully used to achieve good bismuth removal and how many pit falls and draw backs have been overcome.IntroductionASARCO operates one of the largest copper refineries in the world at Amarillo, Texas. The main feed for this refinery is produced at the Hayden smelter in Arizona. During the operation of this smelter a variety of metals are carried as impurities in the copper anodes because of the diversity of concentrates and residue products used as raw materials in the smelter feed mix. Even though the impurities are concentrated enough to be detected at the smelter, it is difficult to remove them completely. A simple way to control impurities at the smelter is to minimize the addition of material with a high concentration of impurities to the charge in order to reduce the output of this metal species. All this leads us to have a ""refinery problem"" [1,2,3]."

Jan 1, 2012

By H. Bernier

The Noranda Inc., CCR Division, copper refinery located in Montreal-East, Québec, Canada, has expanded over the years to reach a capacity of 410,000 metric tons of cathode production per year. The expansion process resulted in nine, parallel, 200 m. long bays each equipped with its overhead cranes and manually operated washing machines. Anode scrap washing and piling was done manually. The mechanization of the tank house involved the elimination of 18 cells at one end of each of the bays in order to install transfer conveyors where anode scrap and cathode loads are deposited by the bay cranes. The cathode loads are brought by new transverse cranes to new machines where cathodes are washed, piled in predetermined bundle weights, check weighed, strapped then shipped in trucks or railroad cars. Suspension bars are automatically removed, stacked in magazines and sent back to the starting sheet machines. Anode scrap loads are brought to machines located near the anode furnaces where they are washed and piled in bundles for easy charging. The mechanization has eliminated numerous hazardous jobs and has realized a reduction of 0.2 man-hours/ton. After these modifications, the refinery production capacity now stands at 370,000 metric tons per year.

Jan 1, 1987

By Oleg I. Platonov

Method of high-temperature reduction of oxygen-bearing sulfurous gas has been developed at Copper Plant (CP) of MMC ?Norilsk Nickel? Trans-Polar Division (PD) with the aim of producing elemental sulfur from Vanyukov furnace? off-gas. Non-explosive reduction technology of oxygen-bearing sulfurous gas by methane utilized at Copper Plant has been designed to separate the processes of gas heating and sulfur dioxide reduction based on different kinetic of the reactions oxygen fixing and SO2 reduction. First, natural gas promptly reacts with oxygen contained in the process gas to heat a gas mixture up to the temperature of sulfur dioxide reduction (1200C). Then isothermal reduction takes place within 1 sec. Combustion chamber (pre-chamber) design developed based on the above principles is presented. Practical experience of the two reduction reactors operation at CP since 1996 proves high efficiency of the developed reduction process. The volume efficiency rises dramatically thanks to the fact that both fuel and reducing agent are fed into the reactor volume in the form of high-speed turbulent jets providing an intensive mixing of the reacting gases. On condition of equal internal volume of the reactors, the developed process offers higher efficiency of reagent interaction resulting in sulfur conversion exceeding 90%, as compared to the equilibrium one.

Jan 1, 2006

By He De-wen

The increasing population and living standard in urban areas, have been accompanied with the growing quantity and composition complexity of rubbish, which are causing well-known social effects of pollution, while rubbish (solid waste) is a recyclable resource. To convert rubbish into useful materials, the essential measure is to carry out sorted collection of rubbish. The preconditions of implementing sorted collection are presented in the paper. 1 Characteristics of rubbish composition and amounts of recyclable contents are basic condition to implement sorted collection. 2 The existing available technologies of recycling, economic benefit from recycling, and disposal scheme of residual rubbish are restrained condition for sorted collection. 3 Public understanding and support to sorted collection are the key to success. 4 The government policies to be favorable for sorted collection is the pledge of success. 5 The establishment of a steady solid waste recycling market is also a guarantee to implement sorted collection continuously. 6 To establish management system of rubbish recycling as soon as possible. Further, the methods and procedure of sorted collection are discussed in detail and beneficial comments and theoretical basis to promote sorted collection of rubbish in urban area are presented; it will contribute reference value to municipal solid waste management.

Jan 1, 2006

By G. St-Amant, V. Cloutier, E. Ghali, S. Jin, G. Houlachi

During the casting of lead-silver anodes, variations in cooling rates result in the formation of an uneven microstructure. The slowly cooled areas (SCA) have a coarser microstructure than that of the remaining part (called "the general zone"). The effect of anode microstructure on the electrochemical behavior was investigated using galvanostatic, potentiodynamic and electrochemical impedance techniques. The results show that the resistances for the two steps of the oxygen evolution reaction on the slowly cooled areas of Pb- Ag anodes are higher than that on the general zone. The double layer capacitance for the first step of the oxygen evolution reaction (OER) and the pseudocapacitance of the second step of OER on SCA are smaller than those on the general zone. The potentiodynamic results show that the amount of lead dioxide formed on the SCA is greater than that of the general zone of the anode. The potential decay curves after 30 minutes of galvanostatic polarization at 45 mA/cm2 show that the corrosion potential of the SCA is 200 mV lower than that of the general zone. This can lead to perforation because of the formation of a galvanic cell with a small anode and a large cathode.

Jan 1, 2000

By Daojin Cao

The chemical components in the saturated aqueous solution of ammonium dimolybdate (ADM) were investigated at room temperature by comparative Raman spectroscopy. In order to explore the further detailed results, a new method of qualitative and half quantitative analyses, based on the main vibrant frequencies and the intensity ratio of the strongest peak to the second strongest peak recorded in Raman spectrum of saturated aqueous solution of ammonium heptamolybdate tetra hydrate (AHM), was put forward and attempted to analyze the chemical components of saturated aqueous solution of ADM. The results showed that there was obvious difference between Raman spectrum of saturated aqueous solution of ADM and that of ADM, but there were good relationships between Raman spectrum of saturated aqueous solution of ADM and Raman spectra of the three samples including AHM, the saturated aqueous solution of AHM and monomolybdate ion in aqueous solution. It was found that aggregated dimolybdate ion ({Mo2O72-}n)did not exist in the saturated aqueous solution, and was changed into heptamolybdate ion (Mo7O246-) and monomolybdate ion (MoO42-), which were in equilibrium each other, but the distribution ratio of heptamolybdate ion was larger than that of monomolybdate ion. In addition, Raman spectral pattern of saturated aqueous solution of ADM was reported.

Jan 1, 2006