Search Documents

By Oscar Jaime Restrepo, Juan Camilo Restrepo, Jorge Ivan Tóbon

Portland cement is obtained by a conventional synthesis process from a mixture of limestone and clay at high temperature (1450 °C). This work reports the possibility to obtain cement silicates via alternative methods like Solution Combustion Synthesis (SCS), which optimize both time and temperature, and the consequences to energy efficiency and mitigation of CO2 emissions. The production of one ton of cement emits between 0.62 and 0.97 tons of CO2 into the atmosphere. In this process the CO2 emissions are between 21 and 59%. The combustion methods are chemical redox processes in which, at high temperature, a self-sustaining and fast wave is generated from using chemical precursors and organic fuels.

Jan 1, 2016

By Dian Adisty, Leiv Kolbeinsen, Eli Ringdalen

In Si and FeSi production, the main Si source is SiO2, in the form of quartz. Reactions with SiO2 generate SiO-gas that further reacts with SiC to Si. During heating, quartz will transform to other SiO2 modifications with cristobalite as the stable high temperature phase. Transformation to cristobalite has been investigated and shown to be a slow process where the rate varies between the investigated quartz types. The effect of quartz versus cristobalite as SiO2 source has been studied for reaction (1) 2SiO2 + SiC = 3SiO + CO, by heating of pellets with SiO2 + SiC in Ar-gas. The reaction was faster with cristobalite than with quartz. Initial experiments indicates that this is the case only in Ar and not in CO-atmosphere The higher specific surface area of cristobalite is believed to contribute to the higher rate. The industrial consequences of the observed difference between quartz types are discussed.

Jan 1, 2014

By Aert Driessen

Australia has large resources of rare earths -- 4.35 Mt of contained rare-earth oxides (REO) in the demonstrated category and 1.69 Kt in the inferred category. Australia's demonstrated REO resources are contained in about equal proportions in placer deposits, which also host Australia's titanium and zircon resources, and in hard-rock deposits. The largest single deposit of rare earths, at Mount Weld in Western Australia, is contained in regolith overlying a carbonatite pipe. It has a demonstrated resource of 1.73 Mt of contained REO and yttrium oxide. The largest demonstrated resources of REOs in placer deposits are in the Murray Bash, southeastern Australia -- a total of 1.90 Mt of contained RE0 in six deposits. However, the REO-bearing minerals (monazite and xenotime) are of secondary importance and their recovery will be determined by the market for titanium dioxide and zircon. The Murray Basin and other pre-Pleistocene basins offer the greatest potential for discovering more REO resources. Australia produces about 7000 t/year of REO in monazite and xenotime nearly all from Western Australia, as by-product of mineral-sand mining; monazite production is about 12 000 t/year (6600 t REO) and intermittent xenotime production is about 50 t/year (25 t REO). About 8000 t/year of monazite containing about 4400 t REO is not recovered separately, or is lost in tailings, as is an unknown but smaller amount of xenotime.

Jan 1, 1992

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By Chonghun Han, Tae-Hwa Choi, Young-Hwan Chu

"A statistical optimization method is proposed to maintain stable operation in a blast furnace with stave coolers. The objective of this study is to find the operating condition which maximizes productivity as well as minimizes the heat load on the stave coolers. In this method, we first analyzed historical data and calculated the heat flux of stave coolers and the burden distribution by mathematical models. In this approach, we determined the variables to optimize and manipulated variables to adjust these response variables. Next, we collected the necessary data for the data variables after preprocessing such as removal of noise and outlier. Finally, we constructed empirical models describing the patterns of response variables in terms of manipulated variables by partial least squares regression method, and then these models were used as objective functions for entire optimization problem. By using appropriate optimization algorithm, we determined the compromised optimum operating condition considering all response variables from the past operating conditions.IntroductionBlast furnace operation which is accompanied by complex physical and chemical phenomena is an essential process for steel industry. In this process, iron ore which is charged into the blast furnace from the top goes downward. It is reduced to iron by CO gas and is melted by the heat of combustion of coke and pulverized coal. The pig iron is tapped at the bottom in liquid phase after removing the slag, which floats on the pig iron.The cooling equipment of the blast furnace wall is changed from the plate type to the stave cooler recently. In order to cool the shell uniformly and eliminate shell spray cooling, Pohang No.2 blast furnace of POSCO (Pohang Iron & Steel Company) was equipped with 11 rows of stave coolers. These staves are only 350mm-thick including the 170 mm-deep refractory on the hot face."

Jan 1, 2001

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By Jing Zhan

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. The composition and morphology of fibrous precursor were characterized by XRD, IR, DTA/TGA and SEM analysis. The results show that XRD pattern and composition of the precursor with fibrous morphology precipitated at pH=9.0 were different from that of ß-CoC2O4?2H2O precipitated at pH=1.0. The mechanism on the thermal decomposition of fibrous precursor was addressed. The influences of various conditions in pyrolysis, including the temperature, time, atmosphere, and the morphology of the precursor, on the morphology, average size and specific surface area of the Co powders were investigated in detailed. At last, the final product, fibrous cobalt powders with diameter about 0.3~0.5µm in size and 40~60 in aspect ratio, were produced by thermal decomposition at 400~500? in the weak reducing atmosphere. The structure of pores in cobalt powders was capillary tube with open ports and the majority was mesoporous.

Jan 1, 2009

By M. B. Mesina

Mechanical separation systems are widely used nowadays for scrap metal processing, but they have natural limitations in product quality. The quality of the final product is considerably improved when sensors are used in the separation process. This paper describes new methods using sensors for scrap metal sorting and quality control. An example is the electromagnetic sensor, which uses the electrical and magnetic properties of materials to distinguish between different non-ferrous metals. The measurement results of two prototypes are reported. The benefits and the possibility to integrate such systems into practical applications regarding the processing of secondary raw materials are also described.

Jan 1, 2003

By Adam Powell

A Cahn-Hilliard phase field model is formulated to describe transport-limited electrochemical reactions coupled with fluid flow in a metal reduction cell. When the reaction is limited by mass transfer of metal ions from the electrolyte to the cathode, the metal-electrolyte interface at the cathode exhibits a Mullins-Sekerka instability, leading to the growth of dendrite-like "streamers" of liquid metal into the electrolyte, which in turn significantly enhance the apparent mass transfer coefficient there. Model results for iron reduction from ferrous oxide in slag show formation of these streamers. Although the double-layer is not included in this model, the related phenomenon of electrocapillarity can be represented by a gradient penalty term which includes the electric potential gradient, such that interfacial energy is a function of the electric field normal to the interface.

Jan 1, 2003

By G. A. Irons, D. Colbert

Several electric arc furnace (EAF) shops have increased the zinc and lead grades of EAF dust by reinjecting it into their furnaces; however, the kinetics of this operation are poorly understood. To understand the kinetics, EAF dust was injected into 70 kg heats of iron or steel in an induction furnace. Supplemental additions of carbon and oxygen to overcome the heat load on the system were also investigated. In all cases, the dust was chemically transformed, and the zinc content increased from 16% Zn to 60 - 80% Zn. About 50% of the zinc in the EAF dust dissolved in the iron or steel. The zinc oxide in the dust is thought to be reduced by carbon and the zinc vapour subsequently dissolved in the iron. A kinetic model for the dissolution process is proposed, and the implications for EAF dust recycling are discussed.

Jan 1, 2000

By Edwin Adoyi Ali, Zainab Shehu Aliyu, Adele Dzikwi Garkida, Muhammad Dauda

Feldspar from Matari, Nigeria was analyzed using SEM, XRD and XRF techniques for microstructural analysis, mineral phase analysis and chemical composition analysis respectively. Qualitative and quantitative XRD analyses revealed the presence of microcline 59.6%, albite 34.7% and quartz 5.71%. The XRF results showed that the feldspar contains 67.32% SiO2, 17.54% Al2O3, 11.33% K2O, 2.75% Na2O, 0.12% CaO, 0.01% MgO, 0.02% MnO2, 0.10% Fe2O3, 0.00% Ti2O, etc and 0.14% LOI. SEM/EDX analysis shows the presence of microcline feldspar as the dominant phase, exhibiting lamellar twinning. The XRD has also revealed that potash has the highest peak, indicating its high concentration. The 0.10% Fe2O3 present is within the permissible level (0.1-0.3%) for glass making and also within the potash feldspar specifications (0.17%). The Matari feldspar is a microcline type, rich in potash, alumina and silica, enabling it meet the standard specifications for alumino-silicate glass.

Jan 1, 2015

By Sheng-li Wu, Guo-liang Zhang, Bo Su

The mineralogical characteristics of iron ores can influence their high temperature sintering performance. In this study, eight iron ore samples from Brazil, Australia, and South Africa were characterized by their chemical composition, mineral types, particle morphology, and gangue dispersity. Meanwhile the influence rules between the mineralogical characteristics and the high temperature characteristics were evaluated and analyzed. The results showed that the effect of SiO2 on assimilation characteristic of iron ores was relatively complex, Al2O3 and LOI of iron ores had negative correlation with assimilation temperature of iron ores, the dense slab-flaky mineral granule restrained to the assimilation characteristics of iron ores; liquid phase of iron ores with high SiO2 content and low Al2O3 content had high fluidity, and the higher dispersity of gangue minerals in iron ores was good to the fluidity of liquid phase.

Jan 1, 2015

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Liyuan Chai, Bing Peng, Ji Peng, Di Yu

"Electric arc furnace (EAF) stainless steel dust has been classified as a hazardous waste by various government regulatory agencies as it releases heavy metals to environment. The solidification of EAF dust is to stabilize the hazardous components to the amorphous silica-alumina-based clays. The process of solidification is investigated and the softening temperatures of dust and additive clay mixtures are measured for economical thermal treatment. The results indicate that the mixture of dust and local clay with the ratio of 1:1 has the lowest softening temperature 1100 °C and it could pass the toxicity characteristics leaching procedure (TCLP) test for the environmental regulatory limits after thermally treated at softening temperature for 15 min. Major phases of thermal solidification product clinker are CaAl2Si2O8, (Fe, Cr)2O3, (Fe, Mg)(Cr, Al)2O4 and Al6Si2O13.IntroductionThe yield of stainless steels in China arrived to 10 million tons in 2006 and more than 0.2 million tons of stainless steel dust are produced annually. Approximately 1-2 wt.% of scrap charged to an electric arc furnace (EAF) enters the off-gases and then is converted into the dust and reported to the bag-house. The disposal or landfill of the dust becomes a serious environmental problem in China due to the increased production of stainless steels in recent years. The dust contains elements such as chromium (Cr), nickel (Ni), lead (Pb), zinc (Zn), cadmium (Cd) and their solubility in leaching media exceeds the environmental regulatory limits [1]. Even though easily feasible for low-grade MgO, it is not appropriate to stabilize the heavy metals from the heavily contaminated soils after the dust landfill [2]. Several dust treatment technologies have been developed and they can be divided into two types. One is to recover the metals from the dust [3, 4] and another is to stabilize hazardous components present in the dust [5, 6]. Recycling of the dust generated in EAF is a remediation option for cleaner production. Direct recycling of EAF stainless steel dust was developed to recover the metal value from the dust and protect the environment [7], but it was only suitable for the dust with high contents of Ni, Cr and Fe. As for the dust with low valuable metal content, thermal solidification is an appropriate choice for the dust treatment."

Jan 1, 2012

By Harald Laux, Stein Tore Johansen

The plunging jet in tapping of steel from converters or electric arc furnaces entrains gas into the steel bath contained in a ladle. Gas entrainment rate and the effect of the gas on the flow pattern in the ladle are studied by means of Computational Fluid Dynamics CFD. The work focuses on the mathematical modeling. Two numerical methods, one for free-surface flows and one for dispersed multiphase flow are combined. A transport equation for the average bubble diameter that incorporates the effect of coalescence and breakup is presented. Results from computations for one ladle and tapping configuration are shown. Our findings indicate that the gas entrainment rate is affected by the material properties of the liquid in the sense that the material properties determine the shape of the jet. Moreover, bubble sizes in the range of two-orders of magnitude are predicted in the ladle. The dispersed diameter model seems to work well. It showed the expected response to material parameters and the turbulent field. However, the presented analysis is just a first step that was limited due to certain simplifications. In order to obtain better insight in the tapping process improvements of the analysis seem necessary.

Jan 1, 1999

By Laszlo Kadar, J. D. Lavers

"In the continuous casting of aluminum killed steel, the tundish nozzle often experiences clogging problems. Water model studies have shown that the clogging problem is dependent on the flow pattern in the nozzle entry region. In particular, the flow can separate at the entrance to the nozzle, leading to the development of a recirculation region. Although a nozzle can be designed such that no recirculation develops, even a small misalignment from the vertical positioning of the nozzle may render the design ineffective.To reduce the possibility of nozzle clogging, the recirculation zone must be reduced or eliminated. This may be achieved by moving the fluid downwards or raising the turbulence level in the separation region. In the case of a tundish nozzle, it is proposed that this can be achieved by using electromagnetic forces.To generate the required electromagnetic force, two systems are considered. The first is based on injecting a DC current; the second by using electromagnetic induction. Both methods are described in this paper. Order of magnitude calculations are provided to illustrate that both methods are essentially feasible. The performance of each method in terms of modifying the turbulent flow characteristics in the nozzle entry region is then examined using a numerical model. It is shown that both methods can greatly reduce the recirculation zone. A cylindrical nozzle was chosen for the model studies since it represents a worst case situation.On the basis of the model studies, it can be concluded that whereas both of the proposed methods have the potential to reduce the troublesome recirculation zone, the induction method appears to be simpler in terms of practical implementation."

Jan 1, 1999

By Yoji Imai, Akio Watanabe, Masakazu Mukaida

"To clarify the feasibility of alkoxides and acetylacetonates as precursors for laser CVD of metal oxides, vapors of tantalum or titanium alkoxides and zirconium acetylacetonate were irradiated by KrF excimer laser and deposits were characterized by XRD and XPS measurements. As for tantalum and titanium, non-stoichiometric crystalline oxides grew nearly phototropically, however, zirconium oxides deposited showed only halo-pattern by XRD measurements. Electric conductivity measurements of tantalum oxides implied the improvement of the insulating properties by the addition of activated oxygen to the ambient.IntroductionThere has been renewed increasing attention to the metallic oxide thin films because ofits promising usefulness in many applications, such as high-Tc superconductors and ferroelectric devices. A variety of thin film preparation techniques have been studied such as sputtering, chemical liquid deposition (sol-gel and metalorganic decomposition), pulsed laser deposition and chemical vapor deposition (CVD). Among them, we think CVD is the most promising method because it offers a high controllability of morphology and good step coverage at relatively high growth rate. Preparation of oxide films by CVD can be achieved using a precursor containing metallic element and oxygen containing gas such as N20 at the same time. However, metalorganic (MO) compounds which contain both metallic element and oxygen, directly bonded to metallic element, seems to be more favorable because some of MO has a good properties for CVD such as a rather high vapor pressure, stability in ambient and low toxicity."

Jan 1, 1998

By Joseph C. Rota

The Carlin Trend is one of the most significant gold mining districts in North America. Located in northeastern Nevada, a total of over 17 million ounces of gold have been produced since 1965 at Newmont Gold Company's open-pit and underground operations. Oxidized portions of the sediment-hosted, disseminated gold deposits at Carlin generally consist of finely disseminated concentrations of sub-micron sized native gold particles hosted in Paleozoic siliciclastic or carbonate rock. Oxide ore is commonly amenable to dump leach or heap leach processing, yielding an average 50 to 70% recovery of total contained gold. Refractory unoxidized ore requires some form of pretreatment oxidation to ensure economic gold recovery. Geologic ore control is typically combined with standard assay and engineering techniques to maintain both grade and metallurgical control ofleach grade ores. Mine geologists provide a vital function through field observation and recording ofmineralogic data during daily, visual blasthole logging. Intricately mixed refractory materials must be separated from oxide ore to ensure highest possible gold recoveries. Geologic information is combined with assay data to create mine polygons in an engineering computer database. Mining selectivity is further enhanced by in-pit ore control geologists who are available to make production decisions based on direct mineralogic observations at active mine faces.

Jan 1, 1997

By Rui Mao, Ke-Xin Nao, Jian-Liang Zhang, Xiang-Nan Xu, Meng-Fang Wei

"In this research, fundamental characteristics of dust and sludge containing iron from the dusting system of sintering process, blast furnace, oxygen converter and rolling process in steel enterprise were studied by chemical analysis, X-ray diffraction analysis, optical microscope analysis, scanning electron microscopy analysis, particle size analysis and other analysis means. Development direction of resource utilization for dust and sludge containing iron from steel enterprise was put forward on the basis of above study.IntroductionDust and sludge containing iron for steel enterprise mainly come from the dusting system of sintering process, pelletizing process, blast furnace, oxygen converter, rolling process and other related process. Iron content of dust and sludge is between 30% and 70%, and they also contain certain content of carbon, calcium oxide, magnesium oxide and harmful elements [1-3]. Output of dust and sludge is determined by raw materials conditions, technological processes, equipment configuration and management level. Dust output in sintering process accounts for about 2% to 3% of the sinter production, while dust and sludge from iron making and steel making process respectively take up 3% to 4% of hot metal and crude steel production, and the solid waste from rolling process accounts for about 0.8% to 1.5% of the output of rolled products [4,5]. Dust and sludge contains Fe, CaO, MgO, C and other valuable resources, it will not only result in the waste of resources, but also cause serious pollution to environment ifthe dust and sludge are not recycled. China's crude steel production in 2012 is about 700 million tons and output of dust and sludge containing iron is nearly 60 million tons, so, it is of great significance to have a resource recycling for dust and sludge containing iron from steel enterprise."

Jan 1, 2014

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994