Search Documents

By K. J. Cathro

A hydrometallurgical process is described for the recovery of copper from chalcopyrite concentrates. The process is based on a cupric chloride leach, the concentrate having first been "activated" by heating it with sulphur at a temperature near 400°C. This activation process converts most of the iron of the chalcopyrite to pyrite, which is insoluble in the cupric chloride leachant. The copper is converted to the mineral idaite, which dissolves readily in hot cupric chloride: at 106°C, 98% of the copper is extracted in a three-stage countercurrent leach, the leaching tirqe being 1 hour per stage. The sulphur of the chalcopyrite appears as elemental sulphur, which is recycled for the activation of further concentrate, the final leach residue consisting of pyrite, plus the gangue present in the original concentrate. The copper extracted can be recovered by electrowinning, using a diaphragm cell. Current efficiency (one-electron basis) is about 70% but the cell voltage is only about 1 V, so that power consumption is three times lower than for the conventional sulphate electrowinning process. The leachant is simultaneously regenerated in the anode compartment. The behaviour of minor elements in the concentrate has also been studied.

Jan 1, 1976

By F. Kongoli

Nonferrous and ferrous smelting industries have recently faced the unavoidable necessity of changing and/or improving the smelting technologies as a result of the use of new raw materials which are becoming available from different geographical areas. These new feed materials usually contain different ore composition and higher level of minor components, which adversely affect the smelting process. Due to the problems encountered in several processes as a result of this feed diversification some work has been undertaken in order to make uniform the feed and avoid later surprises in the smelting process. However this has proven to be very difficult and sometimes almost impossible. In this work a more viable approach is undertaken to deal with this problem. It consists of controlling not the cause of the problem i.e. the feed composition but instead the results of this feed change, i.e. the end-point of smelting technologies. It is shown that this approach, when carried out through advances physicochemical modeling and simulation tools is not only easier and less costly but it also helps the control optimization and automation of the smelting processes. Several examples are given and future work is underlined.

Jan 1, 2003

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would, be reduced at the new smelter to about a half of the sum of those from previous two smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive off gases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Larry M. Southwick, Phillip J. Mackey, A. E. (Bert) Wraith, Albert Pelletier

In 1881, the first commercial pneumatic Bessemer-type converter treating copper matte was successfully introduced by Pierre Manhes at the Eguilles copper plant near Vedène in France. This development followed over a year of testing on a smaller scale at a foundry in Vedène, during which the vertical tuyeres of the conventional Bessemer converter had been successfully replaced by horizontal tuyeres in an effort to avoid the freezing of copper which had occurred in the bottom of the vessel having vertical tuyeres. The Manhes Converter, as it became known, was the first successful large-scale adaptation of the Bessemer concept of using compressed air blown into a melt for metal refining and treatment. Within a few years, Manhes Converters utilizing horizontal tuyeres in either the original type of vertical converter, or a later and more enduring horizontal barrel converter, were in operation at over a dozen copper smelters around the world. It was this process that Messrs Peirce and Smith essentially improved with the introduction of the larger converter which bears their name and the development celebrated at this Symposium. The present paper briefly traces the original development by Pierre Manhes in the early 1880s and which set the stage for the later Peirce-Smith adaptation. The paper observes that the original development by Manhes was in part driven by the need to reduce coal (energy) consumption and hence the production cost in order for Eguilles to remain competitive with the larger plants in Swansea, Wales, where a ready supply of cheap coal helped keep smelter treatment terms of the day low. These themes are eerily resonant of today where booming copper production in China has impacted the industry, and also where energy consumption, closely linked to today’s more familiar theme of ‘climate change’ remains an important challenge currently confronting the entire industry. The paper concludes with comments on these seemingly parallel situations today and offers some thoughts for the future.

Jan 1, 2009

By F. Rivard, L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. Retrofitting plasma torches in place of fuel oil burners lead to lower operating costs, capital cost and greenhouse gas emissions.INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes [!]. Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid start-up and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate [2]. Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates."

Jan 1, 2013

By M. Tangstad, H. Mølnäs, J. D. Steenkamp

"Temperature affects several aspects of pyrometallurgical systems, including thermodynamics and reaction kinetics. Reliability of temperature measurements in laboratory and plant applications is thus important from process, safety and financial perspectives. This case study briefly introduces different techniques utilized for temperature validation, and demonstrates temperature validation on laboratory scale utilizing the wire-bridge method. Pt/Ptl3Rh thermocouple hot junctions were constructed by mechanically connecting thermocouple wires through a pure metal bridge consisting of copper, gold, nickel or palladium wire. When heating the wire-bridge thermocouple alongside a regular Pt/Ptl3Rh thermocouple, temperature offsets were quantified as the wirebridge thermocouple short-circuited at the melting points of the pure metals. At the melting points of gold (1064°C) and palladium (1555°C), average measured temperature offsets were -2.1°C ± 2.3°C and 0.2°C ± 0.4°C, respectively. Results from the copper and nickel wire-bridges were inconclusive. The paper concludes with a discussion on the potential industrial applications of the technique.IntroductionThermocouples are probably the simplest of all temperature sensors, but are widely utilized due to simplicity, versatility and ability to handle a variety of experimental conditions and industrial applications. Additionally, thermocouples are often the only option in research laboratories requiring high temperature measurements, and a high level of reliability is usually required from thermodynamic, kinetic as well as safety points of view.The study presented here originated from a test program where the compatibility between different types of carbon-based refractory materials and industrial slag produced in silicomanganese furnaces were investigated on a laboratory scale utilizing the static crucible test[l]. Due to the nature of the silicomanganese production process, the compatibility tests were to be conducted at 1600CC[2]. Details of the experimental set-up utilized for the compatibility tests are discussed in the Experimental Set-up and Method Statement section later in this paper."

Jan 1, 2012

By Ch. -A. Gandin, M. Rappaz

"The grain selection mechanism which occurs during the growth of columnar dendritic structures is routinely used in the investment casting industry to produce directionally solidified (DS) and single crystal turbine blades. However, the evolution of the grain density with increasing distance from the chill has rarely been correlated with the evolution of the grain texture. This contribution presents a three-dimensional (3-D) stochastic modeling approach which permits the computation of grain maps, pole figures and grain density evolutions in DS superalloys. These predictions are compared with measurements resulting from an automatic indexing technique of Electron Back-Scattered diffraction Patterns. This 3-D stochastic model, which applies to uniform temperature situations, has to be extended to the dendritic growth in a thermal gradient. As a preliminary step, a 2-D Cellular Automaton (CA) has been coupled recently to Finite Element (FE) heat flow computations in order to predict the grain structures in complex shape investment cast part. The application of this CAFE model to the investment casting of a turbine blade is presented. Considering these results, the extension of the CAFE algorithm to three dimensions is discussed.INTRODUCTIONThe selection of columnar grains during the directional solidification of alloys plays a key role during the investment casting of directionally solidified (DS) and single crystal (SC) components for aerospace applications [I]. This selection mechanism, leading to a competition of the dendritic network propagation at grain boundaries, has been the subject of many investigations. In particular, the study of Walton and Chalmers [2] is remarkable since it provides a link between the evolutions of the density and of the texture of columnar grains with increasing distance from the mold wall. Since this original work of Walton and Chalmers, two new tools have become available, which enable one to revisit the problem of grain selection in much greater depth. The first one is a fully automatic indexing technique of Electron Back-Scattered diffraction Patterns (EBSPs) [3-6] which directly gives the crystallographic orientation of the solid at any location of the specimen. Pole figures, orientation distributions, misorientations between grains can be visualized very easily with this technique. This information can be directly compared with the results of a second tool: a three-dimensional (3-D) stochastic model (SM) describing the nucleation and growth of grains in a uniform temperature field [6-9]. In order to extend this model to non-uniform temperature situations, a preliminary 2-D model has been developed [10]. It is based on a Cellular Automaton (CA) algorithm coupled with Finite Element (FE) heat flow computations. Since the details of both the automatic indexing technique of EBSPs and the simulation tools have already been published [3-10], only a brief summary is given here."

Jan 1, 1994

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By Keiji Toyabe

Several purifying techniques have been developed for controlling the impurity levels in the copper electrolyte at Niihama Copper Refinery. These have been carried out as follows; i ) the study of the reaction in liberation made it possible to raise the current efficiency for arsenic removal by more than 50% and to decrease generation of arsine sharply. By applying this method, a good performance was attained at commercial operation. li) the antimony in the electrolyte can be successfully removed by contacting it with activated carbon. This procedure is applicable particularly when there is a large amount of antimony in the copper anode. lli) for the nickel sulphate recovery from the electrolyte, an electric evaporating system was developed. The characteristics of this process are, capability of continuous operation with less manpower, the high recovery ratio of nickel sulphate (more than 85% as nickel) and no black acid formation in the treated solution.

Jan 1, 1987

By Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Rômulo L. Loyola, Frederico M. Margem, Gabriel O. Glória

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of PALF fibers were evaluated. Composites reinforced with up to 30% in volume of long, continuous and aligned PALF fibers were tested in an Instron machine at room temperature. The fracture was analyzed by SEM. This one revealed a weak fiber/matrix interface, which could be responsible for the performance of some properties. The results showed significant changes in the mechanical properties with the amount of PALF fibers.

Jan 1, 2015

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces, They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-OB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderúrgica de Tubarão, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By G. Glinski, K. A. Pericleous

"Recent advances in new computational modelling techniques such as Lattice-Boltzmann and Dissipative Particle methods offer the prospect of simulating complex fluids such as colloidal and dense suspensions in industrial processes. They are referred to as mesoscopic methods since they lie between molecular dynamics at a microscopic atomistic scale «lO-9m) and traditional macroscopic CFD methods (> 1O-2m). The models behave like a 'coarse-grained' gas consisting of fictitious interacting particles, which are much larger than the real molecules of the actual fluid they represent. Inter-particle forces are set so that the collisions collectively mimic the phenomenological transport properties and flow of the underlying fluid at a macroscopic scale.Much of the developmental work to date has focused on laying theoretical foundations based on thermodynamic and kinetic theory. Successful applications include predictions of macroscopic transport properties of complex fluids and flows in porous media and filters. With the constant increase in computational power, these mesoscopic methods are now sufficiently developed to determine their suitability to simulate complex fluid flows in real industrial processes. This work describes the application of meso scopic methods to the stencil printing of solder pastes in the assembly of electronic components. The aim of this work is to assess the ability of these methods to study the transport mechanisms of individual solder particles suspended in the flux solvent as they enter and fill the micro-apertures of a stencil. This paper demonstrates the coupling of such mesoscopic methods to continuum CFD methods to predict the flow of dense suspensions (i.e. solder paste) in industrial processes."

Jan 1, 2001

By Roland Kammel

In combination with various physical and chemical methods also electrochemical techniques are most frequently used to improve the recovery of metals from aqueous dilute process streams or effluents e.g. in electroplating, metal finishing, mining and metallurgical plants. To insure cathodic metal recoveries with favorable current efficiency and high throughputs per unit of cell volume seve¬ral types of electrolysis cells have been developed comprising extended electrode surface areas and/or intensive electrolyte. agitation. The practical experiences with these units indicate especially for the electrolytic recovery of metals whose values are high, that the treatment cost permits profitable operations with relativly short payback periods for the units. Anodic reactions can be utilized for the removal of undesired anion contents or buildups of impurities. Appropriate combinations of these recovery methods are used to improve the versatility and the overall economy. Industrial applications reveal their potentional as addidtive techniques for existing processes to reduce the metal content of effluents to values that meet the guide lines of environmental legislation whereas integrated in-operation recovery methods are nowadays increasingly introduced to approach nearly close-loop operations.

Jan 1, 1992

By S. F. Cheng

Among the many extraordinary features of the rare earths are their magnetic and magnetoelastic properties. The rare earths, e.g. Tb, Dy, Nd, Sm, are known worldwide for their large magnetocrystalline anisotropy and magnetization, which has led to the importance of magnetic rare earths as vital ingredients of modem permanent magnets. In this paper, we focus on the strain dependence of these giant effects which gives rise to huge magnetostrictions, magnetomechanical couplings, and ?E effects. Magnetostrictions greater than 10-3 have been measured at temperatures as high as 500 K. At low temperatures magnetostrictions reaches -1%. ?E effects - 10. No other solid state material has matched these values. A proper balance of magnetic anisotropy and magnetostriction, plus a proper choice of crystal axes lead to alloys which can switch large quantities of energy between the internal (magnetic) and external (mechanical) states with the application of small triggering magnetic fields. In addition to the traditional use of these materials in transduction, they are particularly valuable for smart systems where reliability and robustness are needed such as active structure stiffening and active vibration control.

Jan 1, 1997

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By John Frederick Colloghon, O&apos

Bulong remains the only hydrometallurgical process plant in the world that recovers nickel and cobalt directly from high pressure acid leach (HPAL) laterite leach liquors without need for precipitation of an intermediate product (e.g. sulphide, hydroxide or carbonate). Direct solvent extraction (DSX) of both nickel and cobalt in combination with electrowinning of nickel has been operation at Bulong since early 1999. Focus in the first years has been on ramp-up and resolution of commissioning problems. More recently the focus has been on de-bottlenecking and process optimisation. A number of significant process problems have been resolved, the most difficult being the formation of gypsum in the nickel solvent extraction circuit. Sound control of process chemistry is essential to ensure the production of high quality nickel and cobalt products at the lowest possible cost. This paper describes the numerous changes and enhancements to the process chemistry and plant equipment at Bulong and discusses the importance of ore leach chemistry on downstream impurity metal removal. Potential additional enhancements to further reduce unit costs are also presented.

Jan 1, 2004