Search Documents

By R. K. Singhal

Optimization of a load-haul system for a surface mine involves two processes. The first is proper selection of mining equipment compatible with the minesite job specifications and the second is an efficient utilization of this equipment. All things being equal optimal productivity and cost is achieved when the capacity of the hauling equipment is matched at all times with that of the loading equipment.

Jan 1, 1986

By A. D. Walters

Computer simulation models of preparation plant operations and cost analysis have been used to determine the profitability of individual coals. The model's input consists of raw coal size and washability analysis, operating cost data, and raw coal and clean costs. The model's output predicts yields, qualities, costs and profitability for an individual coal.

Jan 1, 1987

By D. W. Frommer

In continuing its long range studies of methods of treating low-grade iron ores, the Bureau of Mines has developed a new selective flocculation, desliming, and flotation procedure that enables effective beneficiation of the finely disseminated ferruginous jaspers of the Marquette range, Mich. The process, developed on a bench scale and later confirmed in the 800-lb/hr pilot plant, comprises dispersion, selective flocculation, desliming to reject fine silica and clay, and flotation of silica from the remainder of minus 400-mesh pulps. Pilot plant flotation of two Marquette range ores, using the selective flocculation procedure on feeds containing 36 percent Fe, yielded iron recoveries of about 84 percent in concentrates containing 65 to 66 percent Fe and 4 to 5 percent silica. These results were metallurgically superior to those obtained when selective flocculation was not used. Also operating characteristics were better, and reagent costs were lower.

Jan 1, 1964

By Kent E. McElhattan

The selection of efficiency machinery for an underground mining system is a highly skilled art. Modern techniques of mining, based on sound engineering principles, increase the probability of success. These techniques alone, however, will not guarantee maximum productivity. Human judgement, based on experience with mineral seams and geological conditions, remains the single most important input of the decision-making techniques in selecting high production equipment. The myth of a "Scientific Selection Factor" is absurd. The belief that such a factor exists can waste the time and resources of mining management. Until now, mineral extraction from the original desposit has defied all attempts to systematize the knowledge. Computerized programs are excellent for solving underground transportation and ventilation problems. The variables can be defined by mathe¬matical techniques in this type of problem. By the same, token, "Trial and Error" is not an acceptable method in today's technology-minded world. The candid truth of the matter is that practically nothing is known of the phenomenon of extracting a mineral from the solid. Likewise, local conditions make it nearly impossible to predict accurately the reaction of surrounding strata after the mineral has been removed. The unpredictability of the environment resulting from extracting minerals underground will remain a challenge to mining engineers for many years. In fact, we are barely beyond the trial and error stage at this point in time.

Jan 1, 1969

By B. J. Scheiner

The Bureau of Mines has developed a system for dewatering waste slurries by flocculating mineral particles with polyethylene oxide (PEO) and dewatering the resulting flocs on static and/or rotary screens. This paper discusses data obtained from dewatering, rheology, and ion-exchange experiments. A possible mechanism is postulated for the attachment of PEO to claylike particles through a water bridge with the intershell waters of the exchanged ion and the polymer.

Jan 1, 1986

By T. P. Harrington

Research efforts are just beginning to identify the acoustic signatures of very short pulses of sound associated with the fracture of single particles in an autogenous mill. This presentation will discuss the anticipated correlation between these data and the fundamental mechanisms of rock fracture It is hoped that further tests will help identify what design and operating parameters influence the acoustic spectra, determine whether different minerals have different spectra and correlate product particle size distribution with acoustic spectra.

Jan 1, 1980

By V. R. Manukonda

Selective flocculation of iron ores is extremely sensitive to the type and the amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1987

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By Bruce C. Trent

In order to effectively model subsidence caused by underground openings, a two-dimensional computer code has been developed which couples near- and far-field response. The near-field is simulated by a discrete element block code and a finite difference code represents the continuum region in the far-field. The explicit equations allow rapid and inexpensive solutions to geometries which may lead to subsidence. Two sample problems are presented which illustrate the important features of the code.

Jan 1, 1979

By Howard C. Homeyer

Coal and water are the two basic external feedstocks required for a coal gasification project. The WESCO project in northwest New Mexico, a joint undertaking of Texas Eastern Transmission Corporation and Pacific Lighting Corporation, will require about 25,000 tons of coal and approximately 7.5 million gallons of water each day to produce 250 million cubic feet per day (MMCFD) of pipeline quality substitute natural gas (SNG). The coal and water supply arrangement with Utah International, Inc. assures the project of an adequate supply of these two vital feedstocks.

Jan 1, 1974

By P. A. K. Wilkinson

This paper is concerned with the development of an in situ recovery of boric acid from a deep-seated colemanite deposit in California. The deposit contains 147 million tons of borate ore containing 6.4% boron oxide (B203). It is the largest undeveloped colemanite deposit in the United States and because of its unique occurrence and grade, in situ extraction appears to be the most economic viable process. The paper covers the geological, mineralogical, hydrological, well-field development, and extraction considerations leading to the initial pilot plant and subsequent demonstration plant phases of the project. Market potential aspects and preliminary economics of the project are also covered.

Jan 1, 1987

By W. K. Summers

During the past few years monitoring systems have been installed to measure the effects of environmental changes on the ground-water resource. The design of a monitoring system depends upon the designer's perception of how the environmental factors merge with his perception of the ground-water flow system. The validity and representativeness of measurements made during a monitoring program depend upon the validicy of the designer's perceptions and concepts. To optimize the design of a ground- water monitoring program the designer should make preliminary measurements to confirm his assumptions.

Jan 1, 1985

By D. Marcus

A methodology was developed wherein. the increase in compressive strength, mineralogical changes and pore water composition were all studied simultaneously as a function, of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. While the specific data are applicable only to the material studied, the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1984

By William T. Barrett

It is said that Thales of Miletus, 600 B.C.,1 was aware of the attraction of lodestone toward iron and highly magnetic minerals. However, the birth of magnetic concentration followed shortly after the invention of the first electromagnet by Sturgeon in 1825. Sturgeon's magnet was described in the annals of electricity.2 The first attempts to concentrate minerals by the use of magnets date back to about 18473 but the first commercial drum-concentrator was apparently invented by R. Cook in 1849. Credit must also be given to the invention of P. Righter's machine in 1867,5 and to the highly successful Wenström separator devised in Sweden in 1883.8 Since the advent of these early separators there have been virtually hundreds of patents granted covering minor modifications of drum-type magnetic separators. The more important advances from a technological viewpoint have been the design of stable power supplies for d.c. magnets, the advent of ceramic permanent magnets which are now replacing electromagnets for the concentration of ferromagnetic minerals, and advances in general magnet and machine configurations.7 One of the problems facing both the designer and the user of magnetic separators is the evaluation of the body forces acting on particles in the magnetic field of the separator. Perhaps the most elegant method of evaluating the body force associated with a drum-type magnetic separator is that recently suggested by W. F. Brown.8 Brown measures the radial component of the field intensity one-half inch from the drum surface and fits a Fourier series in the angle about the drum axis (Figure 1). Once the coefficients of the series are known, it is then possible to calculate [ ]

Jan 1, 1970

By James F. Lemons

The potential production of cobalt from nickel sulfide deposits in Canada, from nickel laterite deposits in the Pacific Islands, and from the copper deposits of Zaire and Zambia will be a function of the cost of recovery of the primary nickel and copper products. This cost of production varies significantly for these deposits and is related to the differences in the cost of labor, energy, and supplies, to production technology, and to the grade and recovery of nickel, copper, and cobalt. This Bureau of Mines paper investigates these cost and technology differences as they relate to the cost competitiveness of the deposits in Canada, Zambia, Zaire, and the Pacific Islands.

Jan 1, 1984

By S. W. Thomas

One of the most difficult tasks associated with placer mining is the sampling of the deposit. More placer projects have failed due to inaccurate assessment of the reserves than to any other reason. Within the realm of placers, those containing valuable minerals with a high unit value .are more difficult to sample than those with larger bulk, lower unit value minerals. Some items to consider when sampling a placer deposit are as follows: A) A relatively large size sample is needed for accurate valuation of the ground being tested. Placers are composed of many sizes of gravel which makes a representative sample difficult to obtain. B) When sampling placers for high unit value minerals such as gold, any error in mineral content of the sample will be magnified in the calculation of reserves.

Jan 1, 1985

By C. M. Brown

The semi-autogenous grinding circuit at the Utah Mines Limited, Island Copper Operation, located on Vancouver Island, British Columbia, is described. Since start-up of the operation in 1971 grinding circuit throughput has been progressively increased from the initial design rate of 30,000 to the current average 45,000 tonnes per day (t/d) of porphyry copper ore. Key developments and modifications in operating and maintenance practice that have contributed to this increase are reviewed.

Jan 1, 1985

By V. Adamek

The specific lithological conditions over the Pittsburgh coalbed, highly resistive limestone and sandstone units with relatively shallow overburden, prevent the use of any predictive method as developed for European conditions. This paper describes the development of a subsidence precalculation methodology suitable to the mining-geological conditions in the Northern Appalachian Coal Field. It has been found that due to lithological conditions over the Pittsburgh coalbed the subsidence coefficient varies within the area of the subsidence trough. This is different from the European conditions where the subsidence coefficient is considered to be a constant. The effects of lithology, in-the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hypothetically homogeneous overburden and existing lithological conditions, while providing for different mining conditions. Field data from eleven Bureau longwall panel studies were used in the regression analysis. For each panel the characteristics of the variability of the subsidence coefficient along individual profile lines were defined. Regression analysis of the subsidence coefficients from all test sites on the location relative to the edge of the panel has yielded a third degree polynomial equation with a coefficient of correlation of 0.9999. All sensitivity tests have shown good results.

Jan 1, 1985

By Takahide Wakamatsu

In Japan all the complex sulfide ore deposits of base metals have been developed as underground mining. The underground mining cost is extremely high as compared with open pit mining case. Therefore, in milling section of base metal mines, technical advance for maximum recoveries of valuable constitutents in ore has been required all the time to utilize as much ore mined as possible. At present, in mill plants treating "Kuroko", complex sulfide ore, concentrates of copper, lead, zinc, pyrite and barite are produced, with gold and silver contents in the copper, lead, and zinc concentrates being estimated as extra profit. As in the case of Kuroko milling plants, gold and silver contents in the lead and zinc concentrates of lead-zinc ore milling plants are also varuable from an economical viewpoint. Silver content is very high in Kuroko crude ore as well as lead-zinc ore.

Jan 1, 1982