Search Documents

By Daniel E. Walsh

A pilot scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2"), crushed ore from Ester Dome, Alaska. 9.04 tonnes (9.94 tons) of crushed ore were sampled and processed through a Pan-American jig -Wifley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/tonne (22.4 oz/ton). The feed grade to the plant was calculated at 1.71 g/tonne (0.050z/ton). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/tonne (0.042), 1.30 g/tonne (0.038), and 5.47 g/tonne (0.16 oz/ton) respectively. Significant, coarse, free milling gold values were shown to remain in the jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1991

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

Fluorspar was not mined in the United States during 2004, although a small amount of usable synthetic fluorspar (CaF2) was produced from industrial waste streams. The majority of fluorspar consumed in the United States came from imports or stockpiled material purchased from the National Defense Stockpile (NDS). In addition, consumption is supplemented by use of by-product fluorosilicic acid produced at phosphoric acid plants. In 2004, annual production of fluorosilicic acid was 50kt (55,000 st) or about 88 kt (97,000 st) of 92 percent fluorspar equivalent. In 2004, annual production of fluorosilicic acid was 50kt (55,000 st) or about 88 kt (97,000 st) of 92 percent fluorspar equivalent.

Jan 1, 2005

By Robert E. Mazurak

Mines and plants for sale, downsizing, bankruptcies, consolidation, slab imports, minimill growth displacing traditional integrated steel-making. These are some issues for North American iron ore and integrated steel producers. But the blast furnace still remains the workhorse of the ironmaking industry. And direct reduction and other alternate ironmaking technologies have yet to make any serious inroads in North America. How come? This article addresses the current state of primary ironmaking in the changing North American steel industry, the direct reduction market and new technologies under development that may hold some promise.

Jan 1, 2003

By J. H. Tu

The technical paper correctly points out that the kriging variance is not a good measure of the uncertainty of the estimated (i.e., kriged) value of individual blocks. The authors claim that their proposed jack-knife method, which is a rekriging of each block by eliminating, in turn, one sample from m the original sample set and then taking the average of the rekriged estimates, not only gives good block estimates, but the resulting jackknife kriging standard deviation is a useful indicator of the "true uncertainty associated with block estimates." However, they immediately abandon the idea of using the block-by-block standard deviations, reasoning that these standard deviations are not independent and that there is no easy way to utilize them. There may be another reason for not using them. The jackknife standard deviations for individual blocks given in their example are mostly in the range of 0.004 to 0.005 oz/st (0.14 to 0.17 g/t) with only one block having a high value of 0.012 oz/st (0.41 g/ t). These individual block standard deviations are as low as the jackknife standard deviation for the mean grade of the entire shape, i.e., 0.0041 oz/st (0.14 g/t). Do they represent the "true uncertainty" .of the individual block estimates? Could the authors explain this? In a global shape consisting of a large number of blocks, any given sample will affect the kriged estimate of only those few blocks within its vicinity. This is the rationale for the authors' selective rekriging, making the jackknife algorithm more efficient. On second thought, why not do away with jackknifing altogether? Just cumulate and normalize, if necessary, the kriging weights of each sample used during the ordinary block kriging process, and then compute the global variance from these kriging weights and their respective sample grades? After all, isn't the global mean grade nothing but the weighted average of the samples used in the estimation? Reply by G.S. Adisoma and M.G. Hester The jackknife is one of the many tools in a practitioner's toolbox to solve estimation problems. The strengths of the technique lies in its simplicity, i.e., it uses the concept of mean and standard deviation and the fact that it can be easily combined with other tools, in this case kriging. Because the jackknife kriging (JK) estimate is also the mean of the pseudovalues, the JK standard deviation is attractive just as the standard deviation of the mean explains the variability of the data. The difference is that the pseudovalue calculation in jackknife kriging uses the ordinary kriging (OK) weighting scheme instead of simple arithmetic averaging. The data used to illustrate the jackknife technique in the paper con¬sist of high values that are roughly three times the low values. The resulting JK estimate of the block grades show that the highest estimate is roughly twice the grade of the lowest estimate. The contrast between the low and the high estimate is more evident in the JK estimate than in the OK estimate, even though the mean grades of the blocks for the two estimates are very similar. Nonetheless, in this paper, we are concentrating more on the need for a more realistic measure of uncertainty, or precision, for the estimate. Unlike its OK counterpart, the JK standard deviation of the blocks clearly reflects the original data variation. The highest JK standard deviation of the blocks is three times its lowest value. This follows our intuition that, when the samples used to estimate a block is more variable, the resulting estimation variance (or standard deviation) should be higher than the case where the samples are more uniformly valued. However, block-by-block standard deviation or variance is of little practical value in reserve estimation and classification, as well as in mine planning. One is usually more interested in quantifying not the variance of the individual block estimate, but the uncertainties associated with a much larger dimension, such as the minable reserve. Thus, the thrust of the paper is to find a simple way to obtain a single estimation variance or standard deviation associated with the reserve grade estimate. The discussion by J.H. Tu did not mention how one would obtain the global variance from the OK weights and the sample grades. As a technique that offers a data value-based measure of uncertainty for its estimate, the "leave-one-out" jackknife fills this need nicely through the block kriging shortcut approach described in the paper. Note: The first column and the last two columns of Table 3 in the paper should have contained a single number each, namely, an OK estimate of 0.0317, a JK estimate of 0.0333 and a JK standard deviation of 0.0041 oz/st, respectively, for the shape, as are obvious from the text.

Jan 1, 1997

By J. H. Tu

The technical paper correctly points out that the kriging variance is not a good measure of the uncertainty of the estimated (i.e., kriged) value of individual blocks. The au thors claim that their proposed jackknife method, which is a rekriging of each block by eliminating, in turn, one sample from the original sample set and then taking the average of the rekriged estimates, not only gives good block estimates, but the resulting jackknife kriging standard deviation is a useful indicator of the "true uncertainty associated with block estimates." However, they immediately abandon the idea of using the block-by-block standard deviations, reasoning that these standard deviations are not independent and that there is no easy way to utilize them. There may be another reason for not using them. The jackknife standard deviations for individual blocks given in their example are mostly in the range of 0.004 to 0.005 oz/st (0.14 to 0.17 g/t) with only one block having a high value of 0.012 oz/st (0.41 g/ t). These individual block standard deviations are as low as the jackknife standard deviation for the mean grade of the entire shape, i.e., 0.0041 oz/st (0.14 g/t). Do they represent the "true uncertainty" of the individual block estimates? Could the authors explain this? In a global shape consisting of a large number of blocks, any given sample will affect the kriged estimate of only those few blocks within its vicinity. This is the rationale for the authors' selective rekriging, making the jackknife algorithm more efficient. On second thought, why not do away with jackknifing altogether? Just cumulate and normalize, if necessary, the kriging weights of each sample used during the ordinary block kriging process, and then compute the global variance from these kriging weights and their respective sample grades? After all, isn't the global mean grade nothing but the weighted average of the samples used in the estimation? Reply by G.S. Adisoma and M.G. Hester The jackknife is one of the many tools in a practitioner's toolbox to solve estimation problems. The strengths of the technique lies in its simplicity, i.e., it uses the concept of mean and standard deviation and the fact that it can be easily combined with other tools, in this case kriging. Because the jackknife kriging (JK) estimate is also the mean of the pseudovalues, the JK standard deviation is attractive just as the standard deviation of the mean explains the variability of the data. The difference is that the pseudovalue calculation in jackknife kriging uses the ordinary kriging (OK) weighting scheme instead of simple arithmetic averaging. The data used to illustrate the jackknife technique in the paper consist of high values that are roughly three times the low values. The resulting JK estimate of the block grades show that the highest estimate is roughly twice the grade of the lowest estimate. The contrast between the low and the high estimate is more evident in the JK estimate than in the OK estimate, even though the mean grades of the blocks for the two estimates are very similar. Nonetheless, in this paper, we are concentrating more on the need for a more realistic measure of uncertainty, or precision, for the estimate. Unlike its OK counterpart, the JK standard deviation of the blocks clearly reflects the original data variation. The highest JK standard deviation of the blocks is three times its lowest value. This follows our intuition that, when the samples used to estimate a block is more variable, the resulting estimation variance (or standard deviation) should be higher than the case where the samples are more uniformly valued. However, block-by-block standard deviation or variance is of little practical value in reserve estimation and classification, as well as in mine planning. One is usually more interested in quantifying not the variance of the individual block estimate, but the uncertainties associated with a much larger dimension, such as the minable reserve. Thus, the thrust of the paper is to find a simple way to obtain a single estimation variance or standard deviation associated with the reserve grade estimate. The discussion by J.H. Tu did not mention how one would obtain the global variance from the OK weights and the sample grades. As a technique that offers a data valuebased measure of uncertainty for its estimate, the "leave-one-out" jackknife fills this need nicely through the block kriging shortcut approach described in the paper. Note: The first column and the last two columns of Table 3 in the paper should have contained a single number each, namely, an OK estimate of 0.0317, a JK estimate of 0.0333 and a JK standard deviation of 0.0041 oz/st, respectively, for the shape, as are obvious from the text. ?

Jan 1, 1998

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022

By Rolando Gonzalez

Mexico’s role in the world economic community continues to grow. And it is important that the country makes use of its natural wealth, including its large underground deposits of minerals and metals. With that in mind, Industrias Peñoles S.A. de C.V.(Peñoles), a mining, smelting and refining company, began mining lead, zinc and other metals from the Francisco I. Madero Project (FIM). The mine is located about 600 km (370 miles) northwest of Mexico City in the state of Zacatecas. Peñoles plans to remove about 3 Mt/a (3.3 million stpy) of ore from FIM. To achieve this goal, the company needs to optimize its processing, to maximize the amount of metal it extracts through FIM’s large flotation lead-zinc concentrator. To ensure high productivity, Peñoles and its contract engineering firm, M3 Engineering and Technology, of Tucson, AZ, have implemented anore processing system.

Jan 1, 2003

The latest in mining technology and equipment will be show-cased this month at MINExpo International 2004. The event, billed as the world’s largest mining equipment exhibition, is set for Sept. 27-30at the Las Vegas Convention Center. MINExpo, sponsored by the National Mining Association (NMA), is held every four years in Las Vegas, NV. This year’s event is expected to attract more than 40,000 mining industry professionals and executives from around the world. And several key members of the U.S. Congress and other senior government officials are expected to attend. In addition, senior industry and government officials from Asia, Europe, Australia, Africa and South America will be on hand.

Jan 1, 2004

By J. Darlington, A. K. SenGupta

Water-swellable layered silicates, namely, the smectite clays can remove suspended materials (called herein as debris) and metal ions from aqueous streams. The present study shows that the flocculating and metal extracting abilities of smectite clay-based flocculants can be enhanced when these clays are used in conjunction with a specific anionic polymer. Such performance enhancement is attributed to the following: i) the clay-dispersing ability of the polymeric additive, that would translate into an increase in the clay-surface area available for the attachment of the debris particles onto the clay particles; ii) the possibility of dispersant-to-coagulant transition of the polymer during the later instants of the treatment process, as a result of reduction in solvency of the wastewater for the polymer due to the release of cationic species from the clay-based flocculant solids; iii) metal-complexing ability and adsorption properties of the polymer.

Jan 1, 2002

By B. Burke, R. Colquhoun, K. Thomas, R. Walton, D. Fentie

The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources. The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3½ year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.

Jan 1, 2001

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By X. Zhou

In this study, the cyclonic static microbubble flotation column (FCSMC) was investigated for fluorite beneficiation. The structure and principle of the specially designed column are described. Fluorite samples from the tungsten separation tailings of the Shizhuyuan Mine, Chenzhou, Hunan Province, P.R. China, were tested using a small-scale continuous flotation test unit, and concentrates with a fluorite grade higher than 98% were obtained. One rougher and three cleaner stages in the FCSMC achieved the same separation performance as one rougher and eight cleaners in conventional flotation cells. This greatly simplified the flotation circuit and reduced operating costs.

Jan 1, 2007

By James D. Cooper

Long range projections of demand for nonmetallic minerals are presented, together with data on the domestic resources which are available or which can be made available to meet the requirements through the balance of the century. Past successes in solving nonmetallic mineral requirement problems are briefly reviewed to illustrate the capability for solving present and future problems of a similar nature. Major problems threatening the future supply of specific industrial minerals are described together with possible methods for assuring the necessary raw materials for future needs. The growing importance of environ- mental degradation, land use conflicts, and other important factors which affect several or all of the nonmetallic mineral industries is covered, and the necessity of planning for efficient and orderly extraction and rehabilitation of mineral deposits is stressed. The present Bureau of Mines methods and tools for long range planning are briefly discussed.

Jan 1, 1969

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By K. W. Lee, C. Pound, J. Carmody, L. Petersen, C. Nelson, J. G. Cai

The feasibility of developing the Underground Science City below the Kent Ridge Park has been investigated. The primary aim of the study has been to explore the possibility of creating underground space to house a new community of research laboratories and offices. The investigation represents the first such study undertaken in Singapore for a non-military underground facility. The paper describes the geology of the Underground Science City site and illustrates the layout and plan of the Underground Science City. The geology and rock mass below the Kent Ridge Park is generally favorable for the development of an underground cavern complex. Underground Science City can be potentially developed housed in a cavern complex. Several potential development schemes are studied; with various combination of deep/shallow mined caverns of different span sizes and access options. The preferred scheme is shallow, mined room-and-pillar caverns with large spans and shaft accesses at both existing surface Science Park 1 and Science Park 2. The scheme can be potentially expanded laterally to create more underground space for new Underground Science Cities at Kent Ridge area.

Jan 1, 2001