Search Documents

By D. Corrigan, A. Ahmad, R. Sood, J. Bratt, R. Holt

Zinc oxide based electronic ceramics are being used increasingly to protect electric and electronic circuits against transient voltage surges. Varistors are produced by sintering and annealing ZnO based powder compacts through long sintering and annealing cycles. Because of the length of these cycles, a manufacturing plant is saddled with expensive high temperature equipment with low throughput. Ceramics Kingston Inc. has developed a new technology that uses 2.45 GHz microwave energy for sintering and annealing. The new technology has the potential for increasing equipment and labour productivity very considerably. Additionally, the new technology will result in appreciable energy savings and add flexibility to the manufacturing process. Microstructural examination of varistors sintered conventionally and by microwave technology showed considerably smaller grain size in the microwave sintered materials. The electrical properties of the microwave sintered ceramics compare very favorably with those of the ones sintered conventionally.

Jan 1, 1990

By Thomas V. Durkin

About 1.41 kt (45.2 million oz) of gold have been ! produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection. Mining is promoted as an industry while prevention of pollution is required along with reclamation of affected lands to a beneficial use. The South Dakota Department of Environment and Natural Resources' (DENR) system of "one-stop shop- ping" for environmental permits streamlines the permit process. It fosters quick resolutions to compliance problems and helps keep enforcement actions out of the courts. Paha Sapa means "Hills that are Black" in Dakota Sioux. Appearing dark from a distance due to a thick forest of Ponderosa pine, the Black Hills were gold to many people. The exact date that gold was discovered in the Black Hills remains debatable. An inscribed stone tablet found in 1887 near Spearfish recorded these words:

Jan 1, 1998

By Jue Kou, Fazhao Sun, Jiang Liu, Cuili Gui, Baoqiang Yu, Chunbao Sun

A novel special magnetic separator was developed based on the special properties of precious metal-bearing alloy in highgrade nickel matte. The recovery of Au, Pt, and Pd was 77.79%, 84.79%, and 81.79% respectively at optimum operation conditions of magnetic separator feed of 2.5t/h, pulp density of 45%, and flush water of 1.5t/h, and the recovery significantly improved comparing with normal magnetic separator. Magnetic field simulation of the special magnetic separator indicates that magnetic intensity of 0.6 T can be generated on the surface of magnetic drum, which can strengthen the recovery of heavy alloy that contains precious metals. The alternate strong and weak magnetic field can also make magnetic particles rolling on the surface of drum, which will reduce the generation of magnetic agglomeration to a large extent and decrease the content of impurities in magnetic concentrate.

Jun 16, 2022

By A. I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(CO3)2F]. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in fluorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By George G. Reed

Approximately 200 samples of iron ores and other iron- bearing materials have been tested for amenability to treatment by the R-N process in bench scale laboratory work. Twelve large lots, ranging in size from 900 net tons to 18,500 net tons, but generally 3,000 to 4,000 tons each, have been processed in the R-N demonstration plant. The ores tested in the demonstration plant ranged from 27 to 70 percent iron content and gave excellent results. (1) The demonstration plant has a nominal daily capacity of 50 tons of high quality iron briquettes and has now operated for over five years. A continuing program of process improvement is carried on between demonstration on potential licenses ores. An important development is the complete elimination of any secondary products which, in the past (2,3,4,5), resulted from treatment of certain low-grade ores.

Jan 1, 1960

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By Ralph D. Daley, Kevin E. Redinger

The production of coal/water fuel (CWF), a highly loaded mixture of finely ground coal, water, and chemical additives, presents a unique opportunity for significant ash and sulfur reduction through physical coal cleaning. Froth flotation can be integrated with the staged, wet, fine grinding inherent in the CWF production process. A laboratory scale research program was conducted to demonstrate the feasibility of a flexible, integrated coal cleaning/CWF process flowsheet. Performance of the conceptual flowsheet was examined for two coals of CWF commercial interest, Upper Freeport and Pittsburgh seam coals, from central and southwestern Pennsylvania, respectively. Several multi-stage coal flotation and reverse flotation circuits were evaluated. CWF was produced from the cleaned coal in each case at similar solids loadings and viscosities as observed for the raw coal. However, the ash loading and SO2 emission potential for each CWF had been significantly reduced.

Jan 1, 1988

By Catherine T. Aimone

A computerized cost model has been developed to simulate the technical and economic effects of strip mine blasting in the vicinity of structures. Current surface mining regulations restrict the allowable level of production blasting as a function of this distance. Blast design modifications,' therefore must be employed when blasting in the vicinity of homes to ensure compliance with federal and state regulations specifying limits to the seismic effects generated from a blast. The blasting level allowed. is computed by the charge weight of explosives per delay from the following scaled distance formula: [ ] where W is the charge weight per delay, in kilograms (pounds), D is the distance factor corresponding to the regulatory limit of peak particle velocity to which a structure may be subjected to. Current regulations specify 2.54 cm (1.0 in.) per second corresponding to a SD factor of 27 (60) (Federal Register, 1977).

Jan 1, 1982

By Zhu Mingshan, Wu Jiang, Xu Yingqin

A mathematical model to simulate spontaneous combustion of coal in goaf was developed. Under the condition of two-dimensional flaw of air through a bed of uniform mixture of coal, gob, stone etc., the model simulates the temperature rise in the air-and-particle system associated with Arrhenius particle surface reaction. The model is developed as a set of coupled non-linear partial differential equations, which include (1)mass conservation equation for oxygen, (2)energy conservation equation for gas, (3)energy conservation for solid, and (4)velocity equation for gas, that are solved numerically. An elaborate parametric analysis is made of effect of leakage air flux and position of source and sink, parameters relating to the coal accumulating character and the kinetic properties of coal on the tendency to spontaneously combust. In addition, the dynamic process of temperature rise within goaf under several conditions is displayed with picture drawn by computer.

Jan 1, 1991

By John A. Shuster, Joseph A. Sopko

Construction of two shafts, as well as associated deep concrete structures, for a major storm sewer project in Milwaukee, Wisconsin required ground water control and temporary ground support to depths ranging from 19.2m to 55.0m. Lowering of the site ground water table eras not possible because of potential consequences for existing nearby structures. Construction entailed completion of two shaft collars into bedrock. In addition to the shafts, several adjacent connected. structures were completed. Ground freezing was selected to provide temporary ground support and ground water control for all excavations. The first application of using reinforced frozen earth was successfully incorporated on the project. The procedure enabled the contractor to create openings in excess of 9.1m in height, without bracing, through highly stressed frozen earth walls. Design features and construction procedures for completion of ground freezing and related excavation are reported.

Jan 1, 1989

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By George L. Baloo, Dave Kwiatkowski, Jose G. Cañlzales

Capital project funding for a medium to large materials handling project often includes a budget for procurement of supplier-recommended spare parts, and it is the Project Team's responsibility to select these parts. With today's economic climate, limited budget, and other factors, the spare parts selection process is a difficult and arduous effort. This decision carries with it a risk to plant operations and in some cases the commodities producers. Too often the decision-making process is not documented, and the reasons for eliminating and reducing quantities are based on "best guess " Recently on the Solids Handling Phase 2 Project in Jose, Venezuela, the Project Team took a unique approach to this problem. This paper discusses the analytical approach taken by the Project Team, the database system that was developed to manage this problem, lessons learned, and their applicability to pre- project planning and preliminary design.

Jan 1, 2004

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By E. Valdiviezo, J. F. Oliveira

Adsorption of residual flotation reagents onto equilibrium fluid cracking catalysts is a promising method of purification of flotation process water. In the present paper, adsorption of sodium dodecyl sulphate (SDS), dodecyl ammonium chloride (DAC) and sodium oleate onto a spent catalyst from petroleum industry was studied by analysing the residual concentration of the surfactant after contact with the zeolite catalyst. The adsorption of the DAC was rather low but SDS and sodium oleate presented a high affinity for the catalyst surface. The loading capacity was 4.2 kg/ton for SDS and 5.5 kg/ton for oleic acid. After the treatment of the loaded catalyst with a HCI 1 N solution these surfactants are desorbed and the catalyst may thus be regenerated. This would be an additional advantage to its low cost, not to mention its condition as a discarded product and its availability in large tonnages.

Jan 1, 1995

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968

By C. J. Webb

Abandoned uranium mines in the southern Black Hills of South Dakota were sampled for uranium, radium, and rare earth elements during 1992 and 1993. Analyses of water samples from several shallow ponds in the mine pits showed pH values between 3 and 4 with uranium concentrations between 1600 and 2600 ppb. Rare earth elements and their respective isotopes were analyzed with an inductively coupled plasma mass spectrometer and were referenced to a shale normalization pattern. All samples showed an enrichment in the middle rare earth elements. Rare earth levels often were greater than 0.2 ppm. At one site, the concentrations of lanthanides were 150,000 times above background levels. While the southern Black Hills have long been known for rich uranium ore deposits, these analyses show that significant levels of rare earth elements also are present, indicating that the potential exist for future development.

Jan 1, 1995