Search Documents

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By Larry F. Barrett

Anaconda exploration in the Rico mining, district from 1978 through early 1983 resulted in discovery and partial definition of the Silver Creek molybdenum deposit. Approximately 44 million tons of 0.31% Mo are drill-indicated, and projections suggest that the deposit exceeds 200 million tons. No source intrusion has been intersected by drilling, but its composition is suggested by silicic alkali-alaskite porphyry dikes of intramineral age observed at the surface and in drill holes. Age data and fluid inclusion studies indicate that the deposit was formed 5.2 ±2 m.y. ago and that more than 1,200 meters of cover has since been removed by erosion. Both emplacement of the hypothesized source intrusion, and the geometry of the molybdenum deposit, were influenced by three major intersecting faults. The most significant of these, the Last Chance fault, juxtaposes Precambrian quartzite and greenstone against Pennsylvanian clastic and calcareous sediments within the mineralized zone. Wallrock alteration associated with the deposit is characterized by potassic, phyllic, and propylitic zones in non-calcareous rocks, and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Pre-mineral faults that intersect the deposit contain the only surficial molybdenum, tungsten, and fluorine anomalies. Pervasive dispersion haloes of the indicator elements were intersected at depth by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1985

By Robert E. Barry

For new coal-fired power plants, federal regulations require that emissions of sulfur dioxide be limited to 1.2 pounds for every million BTU'S burned. This is equivalent to coal with a sulfur content of roughly 0.7 percent for Eastern bituminous coals and roughly 0.6 percent for Western sub-bituminous coals. The states and their political subdivisions are free to apply more stringent standards and to develop implementation plans covering existing and new units. Most Western-sub-bituminous coals contain less than 1% sulfur and hence their use, in many cases, will allow a utility to meet the regulations. However, there are problems in using such coals in furnaces designed for Eastern bituminous coals, and furthermore it will take many years to open mines and provide transportation facilities to utilities which are now burning coals with a higher sulfur content. Moreover, pending federal legislation would outlaw strip mining on land to which the federal government owns the mining rights. Those utilities who, for one reason or another, intend to continue burning Eastern bituminous coals with sulfur contents in excess of 1 percent are faced with removing SO2 from the stack gases. The alternative of utilizing coal gasification where the sulfur is removed prior to burning in a power plant is still in the early stages of development. Therefore, a large number of processes are under development for SO2 control.

Jan 1, 1974

By A. D. Trujillo, R. D. Wunder

The Chino Mines Co., a Kennecott- Mitsubishi partnership, located in Hurley, NM, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/concentrator modernization commenced in 1980, and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34 kt/d (37,500 stpd). A new concentrator was con- structed near the mine using semiautogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of saleable copper.

Jan 1, 1988

By A. J. Basu

A prototype expert system for planning and designing underground coal mines has been developed in a doctoral study (Basu, 1991) at the University of Kentucky (U.K.). The objective of the study was to provide a design tool for configuring layout parameters, production systems, and for determining economic feasibility. Details of knowledge engineering and the prototype knowledge-based system for integrated and intelligent planning and design have been covered in the dissertation. The prototype demonstrates its robustness by allowing interaction among major design components, most notably among ventilation, ground control, and production planning. A plan for testing and evaluating the prototype, an important phase of software development, is presented here. Existing evaluation procedures for expert system prototypes are discussed and the evaluations for the underground coal mine design expert system prototype are included. The initial testing plan used senior-level mining engineering students to test the acceptance of the prototype. This test suggested the usefulness of such a system for training and instruction. This initial acceptance test was performed with the feasibility prototype. The other test objective, i.e., testing the model's accuracy, involved extensive participation of domain experts. For overall accuracy evaluation, an existing underground coal mine design was compared with the output from a design session using the expert system prototype. The testing procedure is not an isolated, independent development phase. Much of the accuracy evaluation is done at the time of knowledge base development. Therefore, the knowledgebase itself does not need a formal test phase. The major purpose of the field testing is to determine probable user acceptance. The acceptance test determines the completeness of the prototype and also will determine efficiency of user interfaces.

Jan 1, 1992

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978

By Miguel N. Herrera, Abbas H. Mirza, Fiona M. Doyle

The standard test methods used to determine the pyrite content of coal and mineral wastes, and their propensity to release acidic drainage, are critically reviewed. In addition to analysis of total sulfur by combustion, test methods using selective oxidation of pyrite by HNO3 and H2O2 are available. The oxidation kinetics of pyrite vary appreciably from sample to sample, and it is difficult to ascertain whether complete dissolution has occurred in heterogeneous materials. The reliability, reproducibility and suitability of different standard test methods were studied, using well characterized ore and coal pyrite samples. The kinetics of pyrite dissolution were also investigated. The results are discussed in terms of the fundamental chemical and physical characteristics of each sample, and the implications for waste characterization are considered.

Jan 1, 1992

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982

By P. Malozemoff

Discussion by P. Malozemoff I have no objection to using mathematics in the value appraisal of properties. The factor that is not emphasized in the paper is that very few important properties have a lifetime that reflects the initial ore reserves of the property divided by the rate of production adopted. In the majority of cases, major properties mine out several times the initial reserves. How much more will be mined out is not known, and only exceptionally gifted geologists can predict that additional reserves will be found. There is the further factor of metals price, which, over the long term, is not predictable. Another factor vitiating making calculations on initially established ore reserves is the speculative nature of exploration success. In my judgment, the life of a property, in addition to an established ore reserve, should include ample time for exploration to find additional reserves. The likelihood of additional reserves is based on the geological promise of the general area where the mine is established. This is especially important because of various risk factors associated with small orebodies, the economic life of which is about five to seven years. In underground mines, it is not economic to develop reserves beyond a certain depth, so the life of initially established reserves must be limited. In these cases, it is especially important to have a good geological understanding of the orebody and its continuity. To accommodate these concepts and present proof of economic soundness for a mining enterprise, a mathematical analysis should yield a life long enough to allow exploration and the development of additional reserves that would ensure a longer mine life and a more profitable result.

Jan 1, 1994

By S. K. Kawatra, S. J. Ripke

During 1998, 62 million tons of iron ore pellets valued at $1.7 billion were shipped from U.S. mines. These pellets are the primary source for domestic iron and steel production. During pelletization, binders are required to improve the green strength of the pellets. Each year, bentonite binder costs a typical plant from $3 million to $5 million. Reducing the bentonite dosage has the advantages of significant cost savings while producing higher quality, lower silica pellets. The authors have recently identified a new and important bentonite binding mechanism, the fiber theory. During this study, procedures were developed that took advantage of the ability of bentonite to form fibers, and resulted in a dramatic decrease in the necessary bentonite dosage. Acceptable quality pellets were produced with the bentonite dosages reduced in half from 14 lb/lt (0.66%) to 7 lb/lt (0.33%).

Jan 1, 2001

By Chris Joyce, Peter Ryan, Graeme Mcllveen

This paper briefly summarizes regulatory procedures and government agency roles and jurisdictions in each Australian State and Territory. The role of the Commonwealth of Australia and selected current trends in environmental regulation are also discussed. While the Commonwealth has played an active role in regulating specific commodities or mines through its powers over export licences, international heritage agreements and the Territories, such cases have largely been a result of response to specific public issues. This may change; the Commonwealth has established the Resources Assessment Commission and is canvassing the establishment of an Environmental Protection Act, aimed at the standardization of environmental standards through the creation of an Environmental Protection Authority. While the States, the Northern Territory and the Commonwealth lwve nominally different resource planning, environmental project approval and operational regulatory authoritit:s, the fundamental principles hinge on mining lease, planning and pollution control approvals.

Jan 1, 1991

By Hugh E. Cronin, John Ramage

The recommendations resulting from a Dispute Review Board (DRB) hearing of a contract dispute are being challenged more and more frequently. This paper explores possible causes based on the authors’ experiences. Challenges facing the DRB process include: The DRB process is starting to lose some of the informality and flexibility. Both owners and contractors appear to be putting too much weight on a board recommendation on a dispute. DRB’s do not make “decisions,” they provide recommendations for dispute resolution to both parties. The DRB process is not just for contractors to present an unresolved issue to a board hearing. Owners can also initiate a request for a hearing on a disputed issue. For the DRB process to remain a viable element of the successful construction project, confidence must continue to be maintained in a process that is intended to work on behalf of both parties to the construction contract.

Jan 1, 2003

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993

By Charles A. Beasley, Vince Joyce, David E. Beasley, Orlando A. Gallegos, David A. Shuman, Mehmet H. Erten

COAL CHARACARISTICS AND PREPREPARATION REQUIREMENTS Preparation and Market Specifications The national ambient air quality standards (NAAQS) established by the Environmental Protection Agency in 1977 require that when coal is burned, the environmental degradation should be a minimum. For this reason, even coal containing low ash and sulfur must be used in compliance with the NAAQS. The most important pollutants resulting from the combustion of coal are ash, SO2, and NOx gases, and the particulate matter escaping with the combustion gases. The ash is the residue left after complete combustion of coal. It results from the inorganic mineral matter existing in the coal before it is burned. The SO2 results from the combustion of inorganic and organic sulfur associated with the coal. The inorganic sulfur may occur as pyrite, marcasite, or as sulfate sulfur of mostly iron and calcium. The authorities disagree in the definition of organic sulfur in the coal. However, according to ASTM Standard D2492-77,1 the organic sulfur is that sulfur occurring in the coal after subtracting the sum of pyrite and sulfatic sulfurs from the total sulfur in the coal. The NOx gases are produced from high temperature oxidation of nitrogen in the coal that is released into the atmosphere. The particulate matter may consist of fly ash and unburned coal. Selective Mining The cleaning of coal from included ash and sulfur-bearing materials should start at the working faces of surface or underground mines. This can be done by (1) mining only those seams which meet certain quality standards, (2) not mining sections of the seams which may cause deterioration in overall quality of the mined coal, and (3) using a mining method that allows selective mining of coal areas or horizons either underground or on the surface. Since these steps improve the coal quality before the coal reaches the preparation plant, they can be considered to constitute precleaning of coal. During the exploration and development stage of a mine, core and channel samples taken from the coal seam are used to determine (1) petrographic analysis and physical properties,2 (2) character of roof and floor of the seam, 3,4 (3) character and quality of impurities,5 (4) proximate and ultimate analysis, and (5) washability characteristics. However, all of these parameters are subject to considerable variation even within the same seam during the advance of the coal face. This creates a problem in meeting the market demand for coal quality if the coal is to be shipped directly from the mine. If the mining operation is large enough, special blending silos or mechanical blending systems may have to be used to provide uniform quality to the market. However, even if the coal is shipped from a coal preparation plant, prepreparation

Jan 1, 1991

By C. D. Litton

This paper describes two new gas diagnostic techniques which have been used successfully to determine: 1) the combustion status of underground mines which have been sealed due to fire (Littol1 Ratio); and 2) the location of fires in abandoned, underground mines or waste banks (Kim Ratio). The Litton Ratio makes use of the rate of change of CO, calculated on both an air-free and methane-free basis, from mine gas samples and compares these values with those expected from a normal, combustion-free environment. The Kim Ratio uses the concentrations of total hydrocarbons, C2 ?C5, less the methane, to arrive at ratio values which increase as combustion intensity increases. The details of these two new techniques, their application to real situations, and their limitations will be discussed.

Jan 1, 1989

By N. S. P. Kumar

INTRODUCTION Development work at Carr Fork Mine of Anaconda Copper Company in Tooele, Utah commenced in August 1974. A decision to install an underground gyratory crusher for primary crushing run-of-mine ore and waste was made in 1976. Higher throughput rates, larger reduction ratios and greater flexibility in terms of meeting immediate and expanded production needs were the main reasons for selecting the gyratory crusher over the jaw crusher. UNDERGROUND MATERIALS HANDLING Underground crushing and conveying system was designed for a capacity of 16,300 mtpd of ore and waste on a 2-shift, 5-day week basis. Engineering and design of crusher complex was performed by Anaconda engineers at Carr Fork. Figure 1 represents the longitudinal section of mine showing the general materials handling system. Mine area is trackless except for materials and production haulage which is run on rail track on both 1200 and 970 levels. Ore from stopes and waste rock from development headings are handled by 3.8 cu m (5 cu yd) Jarco scoops and dumped into 2.4 m (8 ft) diameter ore and waste passes at the 1200 level. The material gravitates down to the 970 level where it is loaded into 12 cu m (420 cu ft) ASEA mine cars using side loading chutes. The muck train, consisting of 15 to 18 cars and two 27 mt General Electric trolley locomotives, is hauled over a distance of 2,300 m (7,550 ft) to

Jan 1, 1981

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By Brian E. Davies, Bobby G. Wixson

INTRODUCTION The mining, extraction and refining of metals into useful materials is an honorable profession with an ancient and productive history. Civilizations have long depended upon metals for their implements, structures and machinery necessary for survival, growth, and development. Today, as in the future, metals and minerals are essential to the progress of mankind as we approach the 21st century with technologies and concepts that will require new concepts and production from the metal mining and processing industries. Today is the tomorrow we talked about yesterday and the implementation of new ideas is essential if we are to achieve "Frontier Technology in Mineral Processing". Unfortunately, the state-of-the-art mining, processing, smelting and refining methods historically employed were less than desirable environmentally, which has caused todays public to view the metal mining and processing industry with concern. Presently the ancient rock and chat tips connected with old Roman lead-zinc mines which were worked in Wales are causing stream contamination problems that must be corrected at considerable expense to the local governmental agencies (Firth, J.N.M., et al., 1981). However, improved progress has been made and the environmental control and clean-up procedures utilized by modern lead-zinc operations in the "Viburnum Trend" or "New Lead Belt" of South East Missouri may serve as a model to illustrate how alternative technologies, environmental concerns and cooperative efforts contribute to efficient mineral production within the confines of a U.S. National Forest region without significant environmental impacts. This area received international attention when it was opened within the boundaries of the Clark National Forest in the mid 1960's. By 1970 it ranked first in the world by producing 432,576 short tons of lead ore and has since continued in this position producing 451,153 short tons of lead ore in 1983 representing 91% of the total United States lead production (U.S. Bureau of idines, 1983). This production comes from a mining area approximately 40 miles long by 10 miles wide extending in a north-south direction. Geologically the lead is disseminated throughout the Cambrain age Bonneterre Formation, mostly a dolomite, at depths ranging from 700 to 1200 ft. (213.4 to 365.8 m). Galena (lead) is the principal ore mined with lesser quantities of sphalerite (zinc), chaleopyrite (copper) and silver being recovered as economic co-products. This new mining development in one of Missouri is most scenic areas could have led to a classic confrontation between industries and environmentalists. Instead, through the cooperation of industries, governmental agencies and university researchers, the Ozark environment has been protected, and may serve as a model for future coexistence of the mineral industry with the environment. Cooperative Program Development As early as 1965 five new mines and two lead smelters were being prepared for production and environmental concern was an essential part of that planning. All the mining companies became acquainted with representatives of the various federal and state agencies and scientists from the University of Missouri-Rolla (UMR). During the next six years, St. Joe Minerals Corporation, American Metal Climax, Inc., Cominco American Incorporated, Ozark Lead Company (Kennecott) and American Smelting and Refining Company participated in cooperative research efforts. The companies also participated in information exchange meetings, the development of improved analytical methods and the utilization of research findings in the modification or construction of pollution-abatement facilities. Early on research was carried out to determine background values and to establish natural baselines of trace metals in the surrounding environment. The unusual topography and drainage pattern of the mining area were helpful since it was possible to establish control sites and test sites below individual mine-mill operations to study waste-water effects on the receiving streams. The location of the ‘New Lead Belt', mines, mills,

Jan 1, 1985

By George K. Mitteer

The Cowles Mountain Tunnel was driven 2,073 m (6,800 ft) with a 3.43 m (11 ft 3 in) shuffle shoe TBM, for the San Diego County Water Authority, through extremely high strength granitic rock in the City of San Diego, Ca. The initial contract was $10.9 million. Tunneling began in March 1992 and all work was completed in May 1993. After the tunnel drive was completed in September 1992, a 2.44 m (96 in) Welded Steel Pipe was installed, welded and encased with cellular backfill to complete a small portion of the County's $970 million Capital Improvement Project. This paper will discuss the successful completion of a tunnel through some of the hardest most abrasive rock ever excavated with a TBM in North America.

Jan 1, 1995