Search Documents

By N. M. Levine

This work defines and systematizes the physical factors of the problem of leaching and demonstrates for the first time the utility of macropore volume, micropore volume, specific surface, pore size distribution and permeability as parameters of leaching based on a study of the recovery of uranium from the Top Black member of Chattanooga Shale.

Jan 1, 1962

By S. A. Shoop

Vibrations from thirty-seven blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations reported in the U.S. Bureau of Mines studies. Regulations based on USBM data could then be too conservative or lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1983

By B. K. Mishra

The motion of the charge inside a grinding mill is of considerable practical importance. The dynamics of grinding mills have been the subject of study by a number of workers because it can accurately predict: i) the power drawn by the mill, ii) the distribution of forces inside the mill, and hence the wear rate of balls as well as the liners, and iii) mass transport of milled product through the porous ball charge. Some of the earlier analyses of the motion of a charge of particulate material in a tumbling mill were reported by White (1904), Davis (1919), and Dyer (1945) and have been reviewed by Rose and Sullivan (1958). In these works, frictional force at the wall of the mill and between the colliding balls, and the interaction of different ball trajectories, was not considered. Moreover, it was assumed that the profile of the tumbling charge is independent of the degree of filling, which is generally not true. However, all this work led to the identification of so-called "equilibrium surface" which is the plane that separates the rotating charge into two regions. The inner region is static; here there is no motion relative to the mill shell. The other region is a shear region where either the balls flow down the surface of the charge (cascading motion), or are projected out of the surface and follow approximately parabolic paths (cataracting motion).

Jan 1, 1990

By J. J. Pavlica

Grinding in steel mills adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and short-circuit current measurements were made on electrode combinations of pyrrhotite-mild steel and pyrrhotite-stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of ' an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles caused slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1982

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By S. Chander

The effect of sample storage in argon and in air on kinetics of oxidation of pyrite from a coal source was studied using accelerated weathering test in laboratory columns. Prior to the weathering tests the samples were crushed, ground, and stored for various time periods in argon and air. The results showed a dramatic difference in the rate of oxidation of the aged samples. The differences were interpreted based on the hypothesis that the aging of pyrite led to the formation of surface coatings which changed with time. The significance of these results in pyrite/reagent interactions in flotation and in evaluating the acid mine drainage potential of pyritic waste materials is discussed.

Jan 1, 1993

By Jon T. Langstaff

The microseismic method of detecting instability and high-stress zones in underground mines was first developed in this country by the US Bureau of Mines in the early 1940's (Obert and Duvall, 1957). Early laboratory experiments showed that when competent rocks are stressed in a testing machine, the rock noise rate (number of rock noises per unit time) increases with increasing applied stress. This increase is more pronounced as the ultimate strength of the rock is approached. Subsequent testing of rock noises in underground mines confirmed this laboratory experience and much effort has been directed in recent years to make use of this property to develop a practical method of predicting rock failure. Investigations conducted in the Coeur d'Alene district mines have pointed out a definite relationship between the stress buildup in a rock mass caused by mining activity and the emission of audible and subaudible seismic activity (microseisms). In 1968, a concentrated joint effort by USBM Denver Mining Research Center and American Smelting and Refining Co. at Asarco's Galena mine was undertaken to verify several theories regarding the generation of microseisms (Blake, 1971; Blake, Leighton, and Duvall, 1974; and Kovacs, 1973). Findings indicate that (1) rocks under stress emit detectable seismic energy; (2) the energy source can be located using a triangulation method involving travel time differences to various receiving stations; (3) the rate of release of seismic energy increases with increasing stress; and (4) this increase in noise generally precedes a major rock failure (rock burst).

Jan 1, 1979

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By J. J. Carlson

An important factor in filtration is the zeta potential of the particles. Since zeta potential is a function of pH, it was hypothesized that adding CO would lower the pH and zeta potential. A reduction in zeta potential should enhance the flocculation and increase the filtration rate. This paper describes the effects CO on the zeta potential of both pure hematite and samples of hematite concentrate from an iron ore processing plant. A significant shift in the zeta potential, as a function of pH, curve was observed. These results point to an alteration of the particles mineralogy, not just a shift in pH.

Jan 1, 2010

"INTRODUCTION While the United States coal mining uses prescriptive regulation under the Title 30 Code of Federal Regulation enforced by the Mine Safety and Health Administration (MSHA), Australia uses a risk based approach. Australian regulation is individual to each state. In Queensland, Australia this risk based approach to address principal hazards is underwritten by the Queensland Coal Mining Safety and Health Act of 1999 and the Coal Mining Safety and Health Regulation of 2001. Each Queensland Mine is required to have an overarching Health Safety and Environment Management System, of which Safety Management Plans are an element. “Safety Management plans (SMP’s) are intended to formalise the process by which mines address principal hazards and other related matters to ensure the safety of mine personnel.”7 THE QUEENSLAND CONTEXT In Queensland, the basic elements of a coal mine’s safety and health management system must provide for risk identification and assessment, hazard analysis, hazard management and control, and the reporting and recording of relevant safety and health information and data.5 (Part 2 Division 1 Section 6(a-d)) The initial guidance for writing Safety Management Plans comes from the Approved Standard for Mine Safety Management Plans and Guidance Note QGN09- Reviewing the Effectiveness of Safety and Health Management Systems. The Guidance Note and Approved Standard are supplemental to the Act and Regulation, and put in place to provide more clarity around the topic. The definitions in this section come from the Approved Standard and are included to provide context for those who may not be familiar with Australian or Queensland law and regulation. A hazard is defined as a source of potential harm or a situation with a potential to cause loss, while a principal hazard is a hazard with a potential to cause multiple fatalities. A risk is the chance of something happening that will have an impact upon objectives which is measured in terms of consequences and likelihoods. It is important to be able to make the distinction between a hazard and a risk. For instance, a lion is a hazard, while the risk associated with a lion is getting eaten. As defined by the Queensland Approved Standard for Mine Safety Management Plans, a Safety Management Plan (SMP) requires a systematic definition of all the actions necessary to ensure that mining operations are carried out safely. A SMP includes, but is not limited to organisational structures, planning, activities, responsibilities, practices, risk identification, audits and reviews.7 The goal of a SMP management plans is to mitigate the risks to bring them to an As Low As Reasonably Achievable (ALARA) level."

Jan 1, 2016

By R. K. Singhal, R. Kolada

A variety of equipment is wed to surface mine oil sands, including bucket wheel excavators/conveyors, draglines, hydraulic shovels, and off-highway trucks. This paper examines the existing mining schemes and equipment wed. Several proposals to improve mine productivity have been presented.

Jan 1, 1988

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

By Robert H. Carpenter

Downstream dispersion curves for certain trace metals were obtained from two mineralized areas in the southeastern U. S. In Lincoln Co., Georgia, 7 sample sets were collected downstream from the Magruder mine, a polymetallic sulfide deposit (Zn-Cu-Pb-Ag-Au) in metavolcanic rocks. Five sample sets were collected along Joe Mill Creek in Grainger Go., Tennessee, downstream from a zone of zinc mineralization in carbonate rocks (Mississippi Valley-type). In both areas, analyses were made of Fe-Mn oxide coatings on lithic fragments and quartz pebbles, and the -80 mesh fraction of the stream sediment. A comparison of the dispersion curves reveals the following: 1.) the anomaly/background ratio is markedly higher in the Fe-Mn oxide coatings for zinc and copper; 2.) the anomaly/background ratlo is markedly higher in the -80 mesh fraction for lead which is not concentrated in the coatings; and, 3.) the Zn/Mn and Cu/Mn ratios in the coatings are useful in that they enhance downstream derectability of mineralization as well as provide for a simpler analytical procedure. There are several potential advantages of using coatings vs. the conventional -80 mesh fraction in stream sediment surveys. Because soluble metal is brought into the stream mainly in groundwater, deeper anomaly sources may be detectable from the oxide coatings than from clastic fractions of alluvium where much of the metal is derived from erosion of soils. Variability due to sampling may also be reduced, providing better discrimination of anomalies. In areas of glacial or alluvial cover, coating surveys may be particularly applicable.

Jan 1, 1975

By Joseph Renk, David Akers, Glenn Shirey

Each year, US coal cleaning plants landfill or impound millions of tons of high-quality, fine-sized coal. This coal is not only difficult and expensive to capture during cleaning, but, if captured, can pose serious materials handling problems. The GranuFlow. Technology was developed and patented by the U.S. Department of Energy (DOE) to address these problems. GranuFlow involves the addition of a coal binding agent such as an asphalt or heavy oil emulsion to coal to reduce moisture, dusting, and freezing and to improve the flow properties of the coal in bins and chutes (1, 2, and 3). When the emulsion is added before mechanical dewatering, the binding agent causes the formation of fine-sized coal agglomerates that dewater better than untreated coal. In addition, the binding agent increases the capture of ultra-fine coal in screen-bowl centrifuges. Previous work by DOE has also demonstrated that such treatment results in a significant reduction in dustiness and a reduced potential to freeze. To address concerns about the handling and combustion characteristics of GranuFlow treated coal, DOE performed a pilot-scale pulverization and combustion test (4). No problems were encountered during pulverization or combustion, and use of this fuel in a p.c. boiler was found to be feasible from a technical perspective. CQ Inc. has an exclusive license from DOE to market this technology and is currently performing a series of commercial demonstrations to determine if GranuFlow is both technically and economically viable.

Jan 1, 2005

By E. C. Ekedahl, R. J. Heath

Introduction Potassium, together with nitrogen and phosphorous, is an essential nutrient required for growth. Since all living things need potash, the major demand for potash - about 95% of the total - is as a fertilizer. Agricultural productivity has increased dramatically in recent times. This increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows then that potash will always be in demand. There is no substitute. Other fertilizers that contain phosphorous (P) and nitrogen (N) are complementary and not competing products. Fireplace ashes (pot-ashes) have a relatively high potassium content. Their value as a fertilizer had been recognized for centuries. But today's potash industry did not begin until deposits of potassium-rich ore were discovered and exploited in Europe during the 19th century. Canadian potash development Potash in Saskatchewan was first recognized in 1943. It was discovered as a byproduct of an oil exploration program. But it was several years later before the existence of a major commercial deposit was acknowledged, and not until 1951 that the first attempt at development occurred. That attempt was unsuccessful. The shaft flooded and was abandoned. It did, however, demonstrate the need for new technology to penetrate the waterlogged Blairmore layer. This was eventually developed and the first mines were brought into production in the early 1960s. Once the technology was available, and the extent and quality of the potash beds became known, a number of companies proceeded to develop mines. By 1970, seven mines were in operation and three more were nearing completion. Combined, total capacity then was 7.6 Mt/a (8.4 mil¬lion stpy) K20. At that time, world potash consumption was about 15 Mt/a (16.5 million stpy). This increase in supply from Canada produced a large potential surplus that shattered the prevailing balance between supply and demand. Although world demand increased steadily throughout the 1960s and early 1970s, it was several years before world supply and demand were again in balance. Saskatchewan capacity has been expanded a number of times. It now stands at 10.7 Mt/a (11.7 million stpy) K20. Actual production has not approached this figure, however. Two new mines in New Brunswick have recently been built with a combined annual capacity of 1.2 Mt (1.3 million st) K20. Total Canadian capacity of about 12 Mt/a (13 million stpy) now amounts to 30% of world capacity. Central offshore marketing organization Canadian Potash Exports Ltd. (Canpotex) was created in 1970 as the offshore marketing organization for Canadian producers. Canpotex is owned by Saskatchewan producers and is their exclusive marketing organization for offshore business. Each company handles its own sales in Canada and the US, but all sales to other markets are handled through and by Canpotex. The Saskatchewan industry has an ore body of a size and consistency unmatched anywhere in the world. Large efficient mines have production costs that compare favorably with other producing countries. On the minus side, Saskatchewan is remote from most major markets. It therefore needs the ef¬ficiencies that stem from one organization that coordinates all offshore shipments and minimizes distribution costs. Agriculture guides potash market In the period following World War II, potash was a classic growth industry. World demand increased each year from 1945 to early 1970s. Since then, demand has been more erratic. Some years show substantial increases, but are followed by significant declines. For about the last decade, the pattern has been unclear and future demand has become correspondingly difficult to predict. North America and Europe together account for about 40% of the world potash consumption. In both areas, farming is characterized by surplus production, declining crop prices, and expensive government support programs. Under those circumstances, farmers respond by minimizing input costs. Fertilizer is one of the items they reduce. Potash is retained in the soil. It is possible to reduce potash application with no immediate deterioration in crop yield. The lower yields occur only when potash levels are depleted. So, farmers can econo-

Jan 12, 1987

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By Ulf Georg Gwildis

Overexcavation and ground loss events during pressurized-face TBMadvance in soft ground can result in unplanned deformations above the tunnel and damage to existing infrastructure. Successfully managing the risk of this occurring is crucial for any project in an urban area to proceed. Common risk management approaches include a combination of establishing suitable ranges of TBM operational parameters and using geotechnical instrumentation for deformation monitoring. Another risk management tool is material flow reconciliation, which varies depending on the specified mining method and the equipment choices by the contractor. This paper compares recent and ongoing projects in the Pacific Northwest regarding overexcavation risk management.

Jun 13, 2023

By G. J. Goldberg

Through the early 1980's, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation of total station systems and their ability to meet the surveying requirements of Bingham Canyon culminated in the purchase of a total station system as the mine re-opened in 1986. This paper presents the procedure for evaluating, implementing and using the total station survey system at Bingham Canyon.

Jan 1, 1990

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Gregory Bogin, Patrick Maier

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. This research focuses on explosion experiments in a reactor with diameter of 71 cm and length of 30.5 m, along with developing the corresponding computational fluid dynamics (CFD) model that captures the observed flame behavior. The results show that the 2D and 3D CFD models are able predict the experimental flame front propagation velocity, but the 3D model shows more explicit conformity than the 2D model.

May 1, 2024