Search Documents

By Naomi H. Harley, Daryl E. Bohning, Isabel M. Fisenne

INTRODUCTION Underground mines in many parts of the world have elevated levels of short-lived 222Rn daughters. Lung cancer implicating exposure to short-lived daughters is documented in the U.S., Czechoslovakia, Canada, Sweden, the U.K., France and Newfoundland. An elevated lung cancer mortality (in excess of that expected) has been observed when cumulative exposure to alpha emitting short-lived 222Rn daughters (218Po, 214pb 214Bi 214Po) is greater than about 60 working level months (WLM) [1]/ (Hewett, D. 1979). This is equal to an absorbed alpha dose of about 30 rads to shallow basal cells in bronchial epithelium. Long-lived alpha emitters are also present in underground mines, and especially uranium mines because of airborne particulates containing uranium. The 238U parent of this primordial series supports other long-lived emitters 234U 230Th, 226Ra, Pb(210Po) which are in some degree of radioactive equilibrium with the parent 238U. Airborne particulates can be present due to drilling on the face of the ore body as well as in all parts of the mine through resuspension from the mine floor. Particles from 1 µm to about 5 µm penetrate the nose with reasonable efficiency and deposit primarily in the tracheobronchial tree. They are removed by ciliary motion (the bronchial escalator) but deliver an alpha dose to basal cells in bronchial epithelium during clearance in the same manner as short-lived 222Rn daughters. It is the purpose of this work to indicate the alpha dose to basal cells in bronchial epithelium delivered by the long-lived emitters 234, 238U. The dose calculations reported here based upon a few measured values of these isotopes in air in uranium mines in New Mexico and Colorado. MEASURED 234, 238U IN URANIUM MINE ATMOSPHERES In 1979, the U.S. Bureau of Mines undertook a study to evaluate personal monitors to be worn by miners to measure short-lived 222Rn daughters. One of these devices sampled air at 100 cm3/min through a 13 mm glass fiber filter, with a small pump worn on the belt. Alpha particles emitted by 222Rn daughters on the filter were measured continuously by a thermoluminescent dosimeter (TLD) chip. Each monitor was worn by a miner for a 170 hour working month and approximately one cubic meter of air was sampled during this period. Six different mines were selected for the test in New Mexico and Colorado. The mines used either wet or dry drilling methods. Miners in each location were equipped with the personal monitors. Subsequent to their use in evaluating the shortlived daughters, Dr. Robert Droullard of the Bureau generously gave us these filter samples along with a few blank glass fiber filters from the same box of filters used in the study so that long-lived emitters present in these mine atmospheres could be determined radiochemically. Four of the samples have been run for 234, 238U. The radiochemical procedure for uranium is adapted from USDOE, Environmental Measurements Laboratory Manual (Harley, J.H., 1976). Briefly, the samples were placed in platinum crucibles, spiked with 232U tracer and pretreated with nitric and hydrofluoric acid. The residue was fused with potassium fluoride to transpose to pyrosulfate. The fused cake was dissolved in 7 [N] hydrochloric acid and the solution passed through an anion exchange column to isolate uranium. Iron was removed using mercury cathode electrolysis. Uranium was electrodeposited onto platinum dies and counted using solid-state alpha spectrometry. The samples from each type of mine (wet and dry) were analyzed. The samples in the "wet" mine in New Mexico were selected on the basis of the original TLD measurement because they were near the maximum occupational standard for radon daughters. These samples should also represent upper limits to longlived activity encountered, since they were obtained at drilling operations on the face of the ore body. Samples collected in the "dry" mine in Colorado were pot associated with a particular location in the mine and should be representative of a month long overall exposure in many locations and operations. The values are shown in Table 1. The two uranium isotopes are in equilibrium and their alpha activity

Jan 1, 1981

By R. Krog, S. Schatzel, H. Dougherty

Longwall coal mine operators in the U.S. are required to ventilate multipanel longwall districts, but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs) and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. U.S. coal mining stakeholders have acknowledged their belief that the T-junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the ventilation air stream on active and inactive longwall panels. Testing was performed on multiple longwall panels that included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. Changes in the T-junction ventilation air distribution over the life of a longwall panel, and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements.

Jan 1, 2011

By Donald M. Ulbrich

As all of us know, the "heat" is on for western coal. The need for western coal is critical if the nation is to reach the goals of Project Independence by 1985. Without the development of western coal, the goals will not be met. It's that simple! That's because 50 percent of our nation's coal reserves lie in the states of North Dakota, Montana, Wyoming, Colorado, New Mexico, Arizona and Utah. And surface mining is the key to unlocking these reserves. Of the nine states in the coal provinces, five-Wyoming, Montana, New Mexico, North Dakota and Arizona-are the best examples since surface mining accounts for 88 to 100 percent of the coal mined in each of these states. Collectively, their annual production more than doubled between 1969 and 1972, rising to 35 million tons per year. And, taken individually, each state's production has more than doubled, also. Total annual production from these five key states could very well exceed 180 million tons per year by 1980-four times the 1972 production level. The biggest producer among the five is Wyoming. Wyoming's production tripled since 1969 to nearly 14 million tons in 1973. So the heat is on for western coal, especially from Wyoming. Now we come to the question of how to mine this increasingly precious mineral. What are the available methods? First, let's take a brief look at several characteristics of western coal deposits.

Jan 1, 1975

By T. McDonald

Test work indicated and plant operation has since confirmed that SAG milling is a viable option for INCO's Sudbury Operation milling rationalization project only if pebble crushing is included in the SAG/ball mill circuit. Throughput increases more than fifty percent with pebble crushing incorporated into the comminution process. The finer product of high speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems.

Jan 1, 1992

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

By J. D. Miller

"It is now possible to use 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site coarse particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining and the processing of industrial minerals. INTRODUCTION Plant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants, and mineral processing plants is needed to improve plant capacity, product quality, and/or process efficiency. Not much on-line coarse particle characterization is done at these plants. Some limited information regarding particle size is obtained on-line from reflected light images using systems such as the OPSA, Split, and WipFrag analyzers. Even laboratory analysis of coarse particles has been difficult because of the large amount of sample required to insure statistical significance of the results. During the past decades laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage [1, 2]. 3D X-ray tomographic analysis had its origin in the medical services industry; it is used to provide internal images of the human body and now has also been developed for non-medical applications [3]. Figure 1 shows a schematic diagram for the cone-beam geometry micro-CT system. In our case X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a three-dimensional image is reconstructed from the collected set of projection images. With the availability of automated high speed X-ray tomography [4] it now seems possible to do plant-site particle characterization at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining, and the processing of industrial minerals"

Jan 1, 2016

By Donald Bishko

Zoning is the legal means by which land use can be controlled. Although zoning laws have historically been quick to prevent quarrying, one is hard pressed to find zoning ordinances which specifically state that land should be used (or held in reserve) for quarrying and prevent other uses such as recreation, housing, etc. This situation is especially true when the mineral to be quarried has a low intrinsic value such as sand, gravel, and crushed stone. The chance of a gold mine surviving urban sprawl is probably considerably greater than that of a sand and gravel pit, even though it is possible that the dollar value of the sand and gravel' would exceed that of the gold mine. The research reported herein was concerned with two major topics: to delineate the real costs associated with the non-protection of our construction aggregate resources (growth minerals) and to develop a computer simulation model which would aid planners in making economically sound decisions. This paper describes the problems faced by the mineral aggregate industry and discusses the role of computer simulation in planning problems. It briefly describes a simulation model which has been developed and previously reported12 and discusses the results of a pilot study conducted on the Tri-City area (Albany, Schenectady, and Troy, New York). 3

Jan 1, 1970

By E. O. Strahl

In the search for economic mineral deposits, the need for efficient mineral or chemical assays is of prime importance. Costly analytical methods and long delays in obtaining assay results severely limit the effectiveness of an exploration program. The assay problem becomes acute once a potential ore body is located and large numbers of samples are generated in close interval drilling programs. In order to avoid the delays and high costs of extensive assays, the exploration geologist or mining engineer is likely to be required to curtail his drilling program, composite samples, or restrict the required analyses to a limited number of critical elements. As a result, the definition of the potential ore body may be less than needed for final economic evaluation. The assay requirements for bauxite exploration usually involve a considerable number of total elemental and empirical analysis. Since the Bayer process for extracting alumina from bauxite involves the selective dissolution and reaction of specific minerals from the bauxite, a direct chemical analysis for elemental composition yields only a portion of the data required to effectively describe the potential economic value of ore body or deposit. To fully characterize the economic value of a bauxite requires digestion, mud separation and mud settling tests under conditions approximating a commercial Bayer plant. A close approximation of the process behavior of a bauxite also can be calculated from a combination of the chemical and mineralogical analyses. By determining the elemental chemistry, mineralogy, and Bayer plant processing characteristics of a few samples of a given bauxite, correlations can be derived that permit defining a bauxite in terms of a given set of process conditions.

Jan 1, 1977

By C. L. Karr

Establishing suitable control of pH, a requirement in a number of mineral and chemical industries, poses a difficult problem because of inherent nonlinearities and frequently changing process dynamics. Researchers at the U.S. Bureau of Mines have developed a technique for effectively controlling such systems. This technique successfully combines the process control capabilities of fuzzy logic and the search capabilities of genetic algorithms. Fuzzy logic offers an effective mechanism for handling nonlinearities, while genetic algorithms can provide fuzzy logic controllers with real-time adaptive capabilities. This Bureau-developed technique is applied to a laboratory acid-base neutralization experiment. Nonlinearities in the laboratory system are associated with the logarithmic pH scale and the changing process dynamics are due to alterations in pH and buffering capacity input solutions. Results indicate fuzzy logic controllers augmented with genetic algorithms offer a powerful alternative to conventional process control techniques in such nonlinear, rapidly changing systems.

Jan 1, 1992

By E. Rigopoulos

Mining disturbs the environment, even when the ores or the minerals extracted are non-toxic. Silver & Baryte Ores Mining Co S.A (S&B) is committed to minimizing the environmental impacts of its mining activities, by implementing an integrated rehabilitation program wherever it operates. The paper discusses the principles for mining-disturbed land restoration activities on Milos Island for a successful outcome.

Jan 1, 2003

By Bruce Watzman

Can the United States mining industry achieve its long-stated goal of zero fatalities ? and what will it take to do so? Does it require new laws and regulations, as some propose, and a continuation of the commandand- control model that has been born out of more than 40 years of regulation and enforcement under the Federal Mine Safety and Health Act of 1969? Or, is it time to consider a new model to manage safety and health and drive continuous, sustained improvement? These are questions that many are debating as mine safety performance, while improved, appears mired in a trough where improvement followed by declines seems to have become the rule rather than the exception. Without doubt, U.S. mines have made significant progress in safety performance during the last four decades, yet the stalled decline in fatality numbers, the industry?s report card of its success or failure, has led some to question whether the industry will achieve zero fatalities in U.S. mining by relying solely on the Mine Act?s framework and implementing its regulations. These are questions the CEO-led task force, set up by the National Mining Association (NMA), considered as it sought to identify impediments to zero fatalities posed by the current regulatory regime. Out of that effort came CORESafety, a common safety and health framework that relies on a management system approach to improve safety and health performance. The goal of CORESafety is to achieve zero fatalities and a 50-percent reduction in the rate of injuries in U.S. mining within five years ? 0:50:5. CORESafety is built on the plan-do-checkact model, which has been successfully deployed by industries, mining and nonmining alike, to drive continuous improvement in safety and health performance. The improvements in safety performance that can be achieved by shifting from a command-and-control regulatory approach to a risk-based systems approach built on the plando- check-act model have been documented in numerous industries. For example, the United Kingdom quarrying industry (Fig. 1), not satisfied with the number of reportable accidents being experienced 1995-2000, established a hard target of a 50-percent reduction in the number of reportable accidents during the period 2001- 2005. Having met this target, the industry then established a further target zero for the period 2006-2010. The mechanism to achieve these reductions? The plan-do-check-act model.

Jan 1, 2014

By W. H. Strickland

The research reported here characterizes ultrasonic ranging sensors for autonomous navigation on underground mine mobile equipment. Because ultrasonic rangers are inexpensive, have no moving parts, have no lenses to clean, are small and unobtrusive, and can measure distances in dusty environments, they are especially sui ted to underground mi ne environments. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of individual rangers and a ring array of 24 sensors. The results showed the sensors have good accuracy and low variability. Additional experiments at AHAX' s Henderson mine Showed the sensors could accurately and reliably measure rib features, convex and concave corners, and drift intersections. The results showed that when used and analyzed properly, the sensor data may be used reliably for underground mobile equipment navigation.

Jan 1, 1990

By B. Andersen

An accurate knowledge of Interactions among mineral particles and between such particles and dissolved and precipitated species Is Important in developing efficient separation processes. In this investigation interactions in Florida phosphatic clay waste, that are relevant to dispersion and selective reagent adsorption, the two main prerequisites for selective flocculation, were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slime were due to unselective polyacryllc acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Ai and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. Further increase in separation of natural slime is likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1992

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

By L. Rintala, P. Latostenmaa, T. Kalliomäki, O. Forsén, I. Lehtiniemi, M. Lundström, J. Aromaa

Conductivity is a typical physico-chemical property that has a substantial effect on electrical energy consumption in the electrorefining process. The objective of this study was to examine the validity of regression models predicting the conductivity of industrial copper electrorefining electrolytes. The models were based on data measured with synthetic solutions on a laboratory scale. The variables included in the models were temperature and the concentrations of copper, nickel, arsenic and sulfuric acid. Both first-order and combined effects of the variables were investigated. The measured data were analyzed using MODDE 8.0 modeling and design software. The validity of the models was investigated by comparing the predicted values with tankhouse conductivity measurements taken at the Boliden Harjavalta Copper Refinery in Pori in Finland. During the tankhouse tests, the conductivity and temperature of the industrial electrolyte were measured, and the composition of the electrolyte was analyzed. The measured conductivity values were compared with the predicted conductivities calculated using the developed models. The conductivity model developed in this paper was shown to be more accurate than previous models and suitable for industrial use.

By Steven McCutcheon

As most of us have learned through prior and often frustrating experience, anyone proposing to construct a new or expanded mining-ore processing facility must first contend with a rather complex array of environmental laws and permitting regulations administered by a number of different Federal, State and local agencies. At our lost count, there were about 55 federal enactments affecting base and precious metals projects. Applicable State and local laws will usually increase that number significantly. The time and costs associated with complying with all these various regulatory programs usually constitutes one of the major areas of uncertainty in the development of a proposed project. There are many in the mining industry who firmly believe that these environmental regulation and permit programs necessarily causes significant delays and increased costs in the development of a project. This belief, unfortunately, is probably a result of a basic misunderstanding of how the environmental permitting and regulatory system actually works.

Jan 1, 1984

By Donna Wallace

Past EPA groundwater monitoring programs required that contamination not leave the boundaries of a disposal facility. New regulations under the Resource Conservation and Recovery Act (RCRA) require that once hazardous waste constituents are detected beyond the limits of the disposal area, a program to define the rate and extent of contaminant migration must be instituted. Future regulations are likely to include even more stringent groundwater protection criteria. The implications of both the existing and probable future groundwater protection and monitoring requirements in terms of using geologic containment as a means of disposing of hazardous waste are explored in this paper.

Jan 1, 1981

By Yvon H. Poirier

Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976. Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen percent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March '80, Sidbec-Normines use coke addition as a current operation. This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port-Cartier pellet plant.

Jan 1, 1982

By Eugene N. Cameron, Igor N. Sviatoslavsky, Harrison H. Schmitt, Gerald L. Kulcinski

The recent discovery of large amounts of helium-3, a valuable thermonuclear fuel, on the surface of the Moon has prompted engineers and scientists to examine the commercial attractiveness, thetechnological feasibility, and the environmental features of this important resource. The main feature of this fuel cycle is the low (˜ 1%) fraction of energy released in neutrons. Such low neutron fluxes result in important reductions in the amount of radioactivity, afterheat, and radiation damage in a fusion power plant. On the other hand, the high fraction of energy in charged particles and synchrotron radiation can be directly converted to electricity, resulting in very high efficiencies of electricity production (˜60.70%). It has been shown that there is 10 times more energy in He3 on the Moon than there ever was in fossil fuels (i.e., coal, oil, and gas) on the Earth. The techniques and equipment needed to extract the helium-3 have been examined and internationally acceptable mechanisms for the industrial development of this resource have been outlined. This paper expands on the financial, environmental, and technical aspects of the recovery of helium-3 for use in the 21st century.

Jan 1, 1990