Search Documents

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

By Glen L. Black

Choosing a mining method for an underground orebody is a complicated and often iterative process. Advances in technology have given design teams an array of possibilities for methods and equip¬ment. Hecla Mining's discovery of the deep Gold Hunter ore body challenged the staff at the Lucky Friday Mine to determine the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization. This includes drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of in¬formation as the project progresses through exploration and development. The Gold Hunter deposit is a steeply dipping vein system in the Wallace Formation of Idaho's Coeur d'Alene mining district. Gold Hunter is a misleading name for the ore body. The vein is a silver-rich, lead-zinc deposit with only traces of gold. The Gold Hunter ore body is located about 1.6 km (1 mile) north to northeast of Mullan, ID. The ore body is mined from the Lucky Friday Mine, located 0.4 km (0.25 miles) east of Mullan. Mining began on the vein from an access drift driven from the Lucky Friday Mine's 4900 level. Production from the ore zone is projected to be 771 t/d (850 stpd). The Gold Hunter ore is combined with Lucky Friday ore and milled in the Lucky Friday mill. The combined ore boosted Lucky Friday's 1998 silver production from 62.2 t/a (2 million oz/year) to more than 124.4 t/a (4 million oz/year).

Jan 1, 1999

By Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources, and resistors. An analogous approach is outlined here for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The modeling technique proposed uses five basic (non-reducible) elements: the H element, the Q element, the D element, the R element, and the N element. These elements are characterized by their (a) pressure gain or loss, (b) air quantity, and (c) pressure-versus-quantity relationship, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine ventilation networks.

Jan 1, 1996

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By SK SAHOO, UK SINGH, SK SHARMA, GSP SINGH

Surface mining accounts for most coal production in Indian geo-mining conditions compared with underground methods, whose implementations are in deeper coal reserves and for lower stripping ratio in a congested operating space. The bord-and-pillar method is the preferred underground method in India for reasons of flexibility and investment cost. While previous researchers conducted field investigations on intact overburden conditions, this study focuses on the strata control issues in a bord-and-pillar depillaring working under the influence of the dead-load condition of voluminous and fragmented softcover of overburden dump material. The modeling results helped in ascertaining the criticality of strata behavior and rib-pillar stability in actual mining conditions when compared with the conventional intact overburden.

By K. P. Chong

Fracture toughness of oil shale is an essential property in fragmentation to optimize particle sizes and permeability distributions in in-situ processes. Fracture mechanics of oil shale has been based on conventional fracture mechanics using notched samples and assuming the material to be isotropic and elastic. Oil shale is a layered material more accurately characterized as transversely isotropic. The senior author proposes to use a semi- circular core specimen with a center crack subjected to three point bending. Singular crack tip elements with isoparametric elements are used. The precracked semi-circular disk is modeled under displacement loading. The effect of crack length on the non-dimensionalized stress intensity factor is investigated by strain energy method, ellipse method, and stress method. Very close agreements are found. The fracture toughness is obtained by compressing the specimen in to failure. Parameters such as oil yield are investigated.

Jan 1, 1984

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

In mining, which is one of the industries with the highest risk of occupational accidents, a primary goal is to enhance safety through the thorough investigation of accidents using reliable methodologies. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analyzed and compared using the life-table and Kaplan-Meier methods. Accident records were classified and analyzed into four categories: environment-related, equipment-related, person-related and other accidents. Findings in terms of survival time indicate that environmentrelated and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as one year after starting work, it is recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it is determined that increasing the use of automation and mechanization in underground coal mines, combined with developing a thorough equipment safety training program to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Feb 1, 2024

By H. W. Hintze

Coal handling facilities, such as utility plants, coal terminals, ports, manufacturing, processing, etc. Protect themselves against interruptions in coal receipts by maintaining a 60 to 90 day supply in storage. Not too long ago, these storage piles were referred in terms of hundreds or thousands of tons. Today, it is not unusual to have hundreds of thousands or millions of tons in storage. Burn, or shipping and receiving, rates have increased dramatically and storage piles have grown in horizontal as well as vertical dimensions. Fixed systems for delivering and retrieving coal from storage have increased in length and operating capacity and have become highly sophisticated in their operation. With few exceptions, mobile material handling equipment is used to handle all coal beyond the reach of these systems. These machines take excess loose coal from the fixed system to the storage area, place it on the storage pile, compact it, maintain the pile, protect against spontaneous combustion, the spread of fires if they occur, and return the coal to the reclaim system as required, plus many of the small chores around the facility.

Jan 1, 1981

By Morton Handelman

The extraction of aluminum oxide_ from its ore is the initial step in the commerical production of metallic aluminum. This is most commonly done by the Bayer Process in which a caustic solution is used to dissolve hydrated alumina from the insoluable materials with which it is associate in bauxite. At the two-thousand ton per day Sherwin Alumina Plant of Reynolds Metals Company, the extraction residue from Caribbean ores is removed from the main pro¬cess stream as the underflow of a continuous clarifier-thickener operation. This sludge, prior to its ultimate r4jection from the process, is washed in a nine-step continuous countercurrent decantation system to recover physically-entrained mother liquor. Control of alumina production costs requires the optimum recovery of solubles from this residue which is generated at the same rate as the finished product. The equipment, operating techniques, controls and process variables which affect the efficiency of this soda recovery from Bayer Process red mud will be discussed.

Jan 1, 1959

By Raja V. Ramani, Wilson Miola

The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (i) the amount of quartz in thesamples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls are necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples. In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.

Jan 1, 1991

By G. Ferrara, P. Bozzato, B. Chinè

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense-medium separation systems, the following two studies were made: a study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV) and a study of the behavior of suspensions of magnetite and ferrosilicon in water in both separators. It was found that the tangential velocity profiles differ in conical and cylindrical vessels. In a conical cyclone, free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e., that of a centrifuge. It was also found that the conical vessel manifests higher centrifigal acceleration and very strong densifying (the density differential) and, hence, the density gradient inside the vessel is large. It was found that the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e., low-density differentials, and hence, the density gradient inside the vessel is small. Also, due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while, in cylindrical vessels, the density cut- point is closer to the medium density. The results provide an interesting description of the differing behaviors of conical and cylindrical vessels, and they help explain the differences in pegormance between the two types of separators.

Jan 1, 2000

By A. J. S. Spearing, T. Kostecki, D. Benton

The use of paste backfill in room-and-pillar coal mines in the United States needs to be fully investigated. This paper discusses a series of physical tests that were conducted to examine the support benefits of theoretical paste backfill regimens in Illinois Basin room-and-pillar coal mines, which necessarily included consideration of weak floor conditions. The series of tests included those simulating strong floor conditions, weak floor conditions, under-confined scenarios, and testing of actual coal-based paste backfill samples. The testing indicated that a paste backfill regimen utilizing a minimum backfill strength of 22 psi at a minimum fill height of 50% of pillar height could significantly increase the longterm stability of coal pillars in the Illinois Basin. Considering typical coal wash plant recoveries, 50% fill would be feasible.

Jan 1, 2014

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By Ronald A. Crowson

Detailed stratigraphic studies of the overburden at North Carolina Phosphate Corporation new South Creek Mine have delineated several aquifers and acquicludes within the 30-meter-thick overburden section of late Pleistocene sands and clayey sands. A major aquifer occurs in the 10-meter-thick sequence of shelly sands of the early Pleistocene Croatan Formation. The water-charged Croatan sands thicken into a paleodrainage surface on top of the Pliocene Yorktown Formation, a major aquiclude. A three-phase dewatering program is projected: 1) improve surface drainage around mine perimeter to reduce both flowage into the pit and rainfall recharge; 2) use a wellpoint system to dewater the upper 8 meters; and 3) use recharge wells along the axis of the paleo- drainage to dewater the overburden below 8 meters.

Jan 1, 1983

By S. E. Phifer

The Haile Gold Mine was the largest gold producer east of the Mississippi River prior to 1942. It is currently the only producing gold mine in the Southeastern United States. Current development involves the mining and heap leaching of some 1000 TPD. Carbon is employed as a recovery medium. Due to its clayey nature and excessive fines in the oxide ore, agglomeration using Portland cement is required prior to leaching. The ore ranges in screen size from two inches to -200 mesh. The agglomerating step combined with certain other conditions has enabled Piedmont Mining Company to achieve recoveries of 90%.

Jan 1, 1987

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997