Search Documents

By Albert L. St. Peter

The "Old Reliable" four million pound blast in March of 1972 marked the opening, as far as is known, of serious efforts to commercialize the In Situ concept. That was a coyote shot, and it was followed by three blasts at McAlester Fuel's "Zonia" operation which were surface hole shots. As the only individual who had a principal part in all four shots, it seems to be appropriate to present experiences in the developments and evolutions of the in Situ method of ore extraction. Some of the problems will be described, along with proposals for management of such projects in the future.

Jan 1, 1976

By R. W. Smith, A. M. Raichur, M. Misra

Mycobacterium phlei has very good potential as a hematite flotation collector. The flotation recovery of hematite is dependent upon the solution pH and concentration of the microorganism. The critical pH for maximum recovery of hematite is around three, which corresponds to the point of zero charge of the microorganism. An excellent correlation between the flotation recovery and bacterial adhesion on hematite is observed. The adhesion of Mycobacterium phlei on hematite can be described by the potential energy of interaction calculations using an extended DLVO theory.

Jan 1, 1994

By Robert D. Coyle, David L. Emmons

Introduction The Cove gold-silver deposit is located in Lander County, NV about 50 km (30 miles) southwest of Battle Mountain, NV (Fig. 1). The deposit is in the north-central part of the Fish Creek Mountains within the McCoy mining district. Gold was first discovered in the McCoy district in 1914 by Joseph H. McCoy (Vanderburg, 1939). From 1928 to the early 1930s, minor production occurred from shallow underground workings. Total gold production was less than 311 kg (10,000 oz; Stager, 1977). The district was inactive until the mid-1960s when it was explored by Bear Creek Mining, Summa Corp., Houston Oil and Minerals Corp., Gold Fields, and Tenneco Minerals. Tenneco began a detailed reevaluation of the McCoy deposit in the fall of 1984. Tenneco's decision to place the deposit into production was based on a geological reserve of 8.7 t (280,000 oz) of gold (Kuyper, 1987). Subsequent exploration and development drilling of the McCoy skarn deposit has more than doubled the mineable skarn reserves to 19 t (615,000 oz) of gold. In September 1985, Tenneco began development work on the McCoy gold-skarn deposit. The project is an open-pit, heap leach mine. The first gold was poured in April 1986. Echo Bay Mines acquired Tenneco's precious metals properties in October 1986. The mining operation and district exploration started by Tenneco is continuing under the Echo Bay's ownership. The Cove deposit was discovered in January 1987 and production began in February 1988. The deposit will begin as an open-pit, heap leach operation. It will be converted into an open-pit and underground mine with a 9-kt (10,000-stpd) mill. Geologic setting The Cove gold-silver deposit is situated on the east flank of the Fish Creek Range. Surface elevations range from 1460 to 1680 m (4800 to 5500 ft). The deposit is 1.6 km (1 mile) northeast of the McCoy gold-skarn deposit. The Cove deposit is hosted by the Augusta Sequence of Triassic age. Three formations of the sequence are mineralized at the Cove. In ascending order they are the Favret, Panther Canyon, and Augusta Mountain formations. The Favret formation is a gray, locally silty limestone that is commonly fossiliferous. The base of the formation is not exposed. Exposed and drilled intervals are more than 60 m (200 ft) thick. Conformably overlying the Favret formation is the Panther Canyon formation. This formation is 215 m (700 ft) thick and consists of a siliclastic and carbonate sequence of conglomerate, quartzite (sandstone), mudstone, limestone, and dolomite. It is a distinctly coarsening-upward sequence of rocks. The top of the unit is conglomerate with chert and quartzite clasts up to 150 mm-diam (6 in.-diam). The Augusta Mountain forma-

Jan 8, 1988

By I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pH's without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35-38% P205, 0.8-1% MgO) with high recoveries (80-85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P205 and 0.8% MgO with a P205 recovery of 76%. Data are also included showing the applicability of the process to the dolomitic-calcareous-siliceous Western U.S. phosphate ore from Utah. A concentrate obtained from this ore assayed 30% P205 and about 1% MaO.

Jan 1, 1987

By Kwadwo Osseo‑Asare, Isehaq Al‑Nafai

The hydrometallurgical processing of bastnasite is a well-known process that is used to extract rare earth metals. However, more accurate measures are required to enhance the efficiency of extracting and recycling rare earths. In this work, Pourbaix (Eh–pH) diagrams for La-, Nd-, and Pr-(F)-(CO3)-(SO4)-(Cl)-(NO3)-(C2O4)-H2O systems were theoretically derived to investigate the stability relations during the hydrometallurgical processing of bastnasite. The diagrams for RE-H2O systems show similar trends to the original ones drown by Pourbaix. The stability domains of RE carbonates were presented by RE-CO3-H2O systems with pH range of 4.5–11. In contrast, the diagrams for RE fluorides showed a large stability region of insoluble REF3 (pH ~ − 1.7–12). The decomposition behaviors of REFCO3 were studied by constructing Eh–pH diagrams for RE-F-CO3-H2O system. The stability regions of bastnasite species extend from nearly neutral to basic media (pH ~ 6.5–12). The acid treatment (using H2SO4, HCl, and HNO3) of bastnasite was investigated by constructing Eh–pH diagrams for REF- CO3-(SO4)-(Cl)-(NO3)-H2O systems. According to these systems, REFCO3 can be decomposed at pH ~ 6.5 when treated with H2SO4 and at pH ~ 1.7 when treated with HCl and HNO3 acids. On the other hand, the alkaline treatment of REFCO3 converts it to RE(OH)3 at pH ~ 11. The recovery of rare earths ions was studied with the aid of RE-C2O4-H2O systems which shows a wide stability region for RE oxalates in pH range of − 2–11. This theoretical approach explained the aqueous relations in the hydrometallurgical processing of bastnasite ore and it can improve the practical hydrometallurgical processing of such ores.

Feb 9, 2024

By Fabio Mielli

The mining industry is a multifaceted industry with special characteristics that make efficient and intelligent operations uniquely challenging, and subsequently call for distinctive and tailored solutions. Not only does mining call for processes that are complicated and energy intensive, but complex material movements and an intricate logistical chain add to the industry?s obstacles in achieving sustainability and performance. This article explores three major challenges and the resulting issues currently being faced in the industry, as well as potential solutions to these impediments by use of energy management, automation and control strategies.

Jan 1, 2011

By William Gleason

"It is safe to say that the coal industry, in the United States and globally, is currently suffering through one of the hardest times in its history.A perfect storm of competition, changing energy demands, politics and public perceptions have collided, inflicting significant harm to the industry that many say is irreparable. This, in turn, has led to massive job losses in some regions, heavy cuts in production and even bankruptcy filings from two of the largest coal mining companies in the nation.Cheaper natural gas can certainly take a large share of the blame for the struggle of coal, as utility companies switch from coal to natural gas for power generation. According to the U.S. Energy Information Administration (EIA) the amount of coal used for electricity generation in the United States is at a 45-year low.November 2015 marked the fifth consecutive month that natural gas was the leading source of power generation in the United States. EIA said generators produced 101,866 thousand megawatt hours (MWh) of electricity with gas in November versus just 87,789 thousand MWh with coal, the lowest monthly level since May 1980 when monthly coal use was 84,884 thousand MWh.According to Robert Godby, director of the Center for Energy Economics and Public Policy at the University of Wyoming, there are a number of factors playing a role in the decline of coal, but he points to the advances in fracking as the tipping point.“A lot of people will argue that regulation is the cause of the decline, and it has played a part, for sure, but the story of the recent past is more about what competition has done to the energy market,” Godby told Mining Engineering. “The war on coal was originally declared by natural gas in 2008.”The price of natural gas, which was at $13 per million Btu before the gas fracking boom, has fallen to as low as $1.68 in December 2015. Likewise, Godby said the cost of wind generation is now lower than the cost of generation from coal and the cost of solar generation is coming down as well. In addition to that, the demand for energy has changed in the past five years with more efficiencies in everything from building design to lightbulbs."

Jan 1, 2015

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By C. C. Russelll, V. T. McLemore

The Metals Mining Sector of the Acid Drainage Technology Initiative (ADTI-MMS) addresses technical drainage-quality issues related to metal mining and related metallurgical operations, for future and active mines, as well as, for historical mines and mining districts. One of the first projects of ADTI-MMS is to develop a handbook describing the best sampling, monitoring, predicting, mitigating, and modeling of drainage from metal mines, pit lakes and related metallurgical facilities based upon current scientific and engineering practices. One of the important aspects of planning a new mine in today’s regulatory environment is the philosophy of designing a new or existing mine or expansion of operations for ultimate closure. The holistic philosophy taken in the ADTI-MMS handbook maintains that sampling and monitoring programs should be designed to take into account all aspects of the mine-life cycle. Data required for the closure of the operation are obtained throughout the mine-life cycle, from exploration through post-closure.

Jan 1, 2004

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By Franz Albert Nonnen

Backfill systems have been used for as long as mining activities have existed. Various backfill methods have been developed over the centuries with consideration for geological necessities, the technical means available, security requirements, and available finances. In the past, backfill systems were introduced and upgraded geographically in accordance with local experiences. In modern times, mining engineers participate in international forums for the exchange of knowledge so that backfill techniques and experiences are shared concurrently in mining areas all over the world. Mine backfilling increases the cost of mining so that great attention must be paid to choose a low-cost, reliable, and low maintenance backfill system. Some methods are described in this paper.

Jan 1, 2001

By Solomon J. Salat

During the major expansion of the Inspiration smelter, which took place in 1973, the bulk material handling system underwent a matching expansion in order to move the required materials. Inspiration is the first smelter worldwide to employ electric smelting in conjunction with the use of Hoboken converters (1), (2). The installation includes a 51 -MVA electric furnace, five 4.25m (14-foot) diameter Hoboken converters, rotary dryer, bedding plant, acid plant, heat recovery steam plant, and gas and dust handling system. See Figure 1, Plot Plan. As of today, the 51-MVA electric furnace is the world's largest in the smelting of copper. Engineering design for the installation was per- formed by Treadwell Corporation of New York. The task of designing the conveyor system was complex because the system had to be installed while the smelter was operating and with minimum plant shutdowns, and it had to serve both the existing and the new smelter. Existing conveyors were redesigned where necessary and incorporated into the new conveyor system. See Figure 2, Flow Sheet. The system encompasses the handling of such diverse materials as wet and dry copper concentrates, cement copper, silica flux, cold dope, and concentrate and flue dust.

Jan 1, 1979

By M. Alley, P. Schroeder, L. Zelazny, S. Nagle

The Old Hickory mineral sands ore body in Virginia (>2000 ha) currently supports a productive rowcrop agriculture. Reclamation experiments were implemented on pilot-scale mining pits from 1995 to 1998. Half of each mining pit was topsoiled (25 cm) while the remaining half was left as either (1) mixed tails/slimes or (2) re-graded subsoil over tails/slimes treated with 112 Mg/ha yardwaste compost. Post-mining productivity was estimated to be reduced by 23%, 3%, 27%, and 20% for each crop (wheat/soybeans/corn/ cotton) in sequence when compared to undisturbed soils. Variability in surface texture and compaction limit restoration of soil productivity.

Jan 1, 2002

By E. Steiakakis, A. Athousaki

Nowadays, stakeholders have a strong say to the enforcement of best practices by mining and quarrying companies. In most cases there is a direct relationship between sustainable development principles and best practices. Mining companies try to apply best practices in order to sustain their operation without lost time and effort to litigation, and other obstacles. However, when and where there is a lack of state or regional mineral policy, or when the mineral policy is fragmented and touching on conflicting laws, mining operations may be subject to additional administrative hassles, and, thus, operators feel threatened and tend to apply best practices loosely. This paper argues that the only way that mining and minerals operations can be a source of development is to ensure that they are working within the framework of sustainable development. Furthermore, in order to follow the paradigm of sustainable development they would need to be guided by a regional, national or even transnational (i.e. European) minerals policy.

Jan 1, 2011

By Bart Bartholomew, Randall J. Essex

INTRODUCTION In June of 2004, at the North American Tunneling Conference in Atlanta, an all-day workshop was conducted to review the application of Geotechnical Baseline Reports (GBRs) for underground construction. The moderator for the program was Bart Bartholomew, former President of Fruin Colnon Construction Company. The program involved commentary by a panel of engineers, owners, contractors, and legal representatives within the North American tunneling industry, as well as an extended audience discussion. The panelists were: Peter Douglass, President, Peter Douglass, Inc. Randall Essex, Executive Vice President, Hatch Mott MacDonald Joseph Gildner, Deputy Director for Technical Services, Sound Transit Randall Hafer, Esq., Kilpatrick Stockton Robert Fitzgerald Esq., Watt, Tieder, Hoffer, & Fitzgerald Kirk Samuelson, Senior Vice President, Kiewit Construction Group DEVELOPMENT OF PROGRAM FORMAT The focus of the program was to assess the state of the practice in the preparation of GBRs, and to discuss improvements that could and should be made with regard to their preparation, interpretation, and application. The approach used to achieve this focus in the broadest possible way was unique, in that it involved the panelists’ preparation of the workshop format and materials months before the presentation of the workshop. First, each of the six panelists was selected by the moderator based on their reputation and involvement in their respective fields of expertise, taking care to maintain balance and contrast within the collective pool of talent assembled. Following selection and agreement to serve on the panel, each panelist was asked to independently submit to the moderator a list of the six most pressing issues involving GBRs that they each frequently encountered in their individual professional experience. Each was asked to rank their issues in descending order of perceived importance. This process resulting in a pool of thirty-six potential or “candidate” issues for use in the workshop program. Contrary to the moderator’s expectations, there was surprisingly little duplication among the thirty-six issues submitted.

Jan 1, 2005

By Wilbur I. Duvall

INTRODUCTION This chapter outlines some general principles and procedures that a rock mechanics engineer can use to arrive at a logical design for the size, shape, and spacings of underground openings in various types of com¬petent rock formations. Rock formations can be clas¬sified into six major categories which are useful for design purposes, provided the necessary input data are available regarding the geology of the site, the physical properties of the rock, the in-situ stress field in the rock, and the general geometry of the underground openings. The US Bureau of Mines (USBM) developed a rock classification system based upon these concepts and found it to be useful for design purposes (Obert, et al., 1960; Obert and Duvall, 1967). This classification sys¬tem is given in Table 1; however, an extra column has been added to the original classification to indicate the appropriate design techniques for each rock class. In this classification system, two main classes of rock are considered: competent rock and incompetent rock. Competent Rock Competent rock is any rock which, because of its mechanical and geological characteristics, is capable of sustaining underground openings without the aid of any structural support except that provided by unmined rock in the form of pillars and side walls, etc. Roof bolts and small random props which support only local loose rock are not considered structural supports. Competent rock is further subdivided into three ad¬ditional categories-massive, laminated, and jointed¬ which are defined as follows: Massive Rock: Massive rock is a rock formation where the spacing between mechanical defects such as joints, partings, or faults is equal to or greater than the critical dimensions of openings, or where the strength of the bond across these mechanical defects is com¬parable to the rock strength. Laminated Rock: Laminated rock is a rock forma¬tion divided by approximately parallel planes of weak¬ness into lamina whose thicknesses are small compared to critical dimensions of openings and where the bond between the lamina is weak compared to the rock strength. Elastic Rock-This is rock whose physical proper¬ties will permit the use of elastic theory to predict strains and displacements from applied stresses. Inelastic Rock-This is rock whose physical proper¬ties are such that strains and displacements are a strong function of time as well as applied stress. Incompetent Rock Incompetent rock is any rock which, because of its mechanical and geologic characteristics, is not capable of sustaining underground openings without the aid of additional structural support in the form of linings, steel sets, or systems of props. This classification system for rock depends not only on the mechanical and geologic characteristics of the rock but on the size of openings and their depth be¬low the surface. For example, many competent rocks at shallow depths for small stress fields could become inelastic rock at greater depths and larger stress fields, or competent massive rock for small openings could be¬come laminated or jointed rock for larger openings. Thus, to classify rock for design purposes requires a knowledge of the geologic properties of the rock mass, the physical properties of the rock, the general size of the openings to be mined, and the average range of the in-situ stress field to be encountered. To design underground openings and structures in rock, it is necessary to use criteria of failure for rock under various stress conditions, and to use safety factors to allow for differences between laboratory and in-situ strength properties of rock and to account for errors in¬troduced by the various assumptions made in the design process. Criteria of failure based on maximum stresses have been found to give reliable results in practice. Thus, it is assumed that rock will fail in tension when the tensile stress exceeds the tensile strength of the rock as determined by a standard modulus of rupture test on samples of rock core. If the tensile stresses in rock are small, then it is assumed that the rock will fail at a value of compressive stress equal to the compressive strength of the rock as determined by standard uniaxial compres¬sive strength tests on samples of rock core. These fail¬ure criteria, when used with appropriate safety factors, can be expressed as:

Jan 1, 1982

At present, discounted cash flow analysis is generally accepted as the preferred method of valuation of mine projects in surface coal mining. One of the major reasons for that is its ability to take into account the time effect of money over the life-of-mine. As a looking-forward method, it requires forecasts be made with regard to economic, technological, technical, geological, and environmental conditions that will prevail in the future. All forecasts are inherently uncertain as they are a function of the uncertainty of all variables of the discounted cash flows analysis. This indicates that the only alternative for modeling the uncertainty in the project evaluation is the development of adequate risk models to serve the decision-making process. The paper offers a model of project cash flows at risk in strip coal mining, which is an integrated corporate risk management solution. The model is based on a stochastic approach that provides the answer to the question about how large is the deviation between stochastic cash flows and the planned value (or that used in the budget) at each time step of the discounted cash flows analysis, that is due to the uncertainty in the model variables. A solution is worked out for the allowable range of the stochastic cash flows variation that determines the probability of achieving the planned value of a mine project. The Monte Carlo simulation technique is used to model the stochastic behavior of the project variables. A case study of an opencast coal mine project is provided to illustrate the applicability of the risk model. The results obtained provide a new understanding of the mine project risk as a component of the project discount rate.

Jan 1, 2006

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977