Search Documents

By J. J. Bean

The development drilling program of the Copper Cities mine indicated that the molybdenum content of the ore would be about 0.011% MoS2' The molybdenum content of the Miami mine at the same time was about 0.025% MOS2' The Miami mill had a very successful molybdenum operation which used bleeder turbine steam from the Miami power plant for the steaming operation. The much lower grade of the Copper Cities ore, the absence of a source of low cost steam and the use of sodium aerofloat as the copper collector which Miami experience indicated did not respono readily to the steaming technique made very doubtful the success of a similar operation at Copper Cities. However, the relatively few pounds of copper that could be recovered from the low grade Copper Cities heads made very desirable the recovery of the molybdenwa,as a source of additional revenue. Accordingly, shortly after the Copper Cities mill began operation, a research program was instituted to develop a suitable method of molybdenum recovery. This program explored first, the successful steaming process then in use at Miami and as expected, found it unable to decompose the sodium aerofloat copper collector. The known chemical depressants were then tried without much encouragement. Finally the copper concentrate was dried, not roasted, to 2-3% mOisture and this along with sodium ferro-cyanide and cyanide resulted in sufficient copper depression that a final molybdenum concentrate containing 1.0% CU could be made. The bench scale testing was followed by pilot plant testing. Sixteen

Jan 1, 1972

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth's surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country's primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By J. R. Pennington

The town of Green River, Wyoming, is located along the Green River on an arid plateau at a elevation of 6,300 feet. Green River has become the center of a booming soda ash industry. The rapid development of coal, oil, and gas resources, coupled with the soda ash boom, have created growth pains for the area. Green River and Rock Springs have experienced a 20-25% population increase in 1973 alone. However, public officials, business leaders, and local citizens are taking positive steps to ease the problems relating to housing, schools, medical services, and recreational facilities. What Is Soda Ash? Soda ash is one of the most widely used chemicals in the world. It is an important raw material in the manufacture of glass, paper, soap, petroleum products, metals, chemicals, pharmaceuticals, plastics, and a host of other items essential to every day living. In ancient times, soda ash was obtained from water solutions of various desert earths. Later, it was produced by leaching the ashes of wood and seaweed. For the past 100 years, it has been manufactured by the ammonia-soda process, which employs large quantities of salt, limestone, and coal as raw materials.

Jan 1, 1974

By Ekkehart Mertins, Hans-Dieter Wasmuth

During the last years many new concepts have been presented for magnetic separation of feebly magnetic minerals by using the new high-duty permanent magnetic material especially in Open Gradient Magnet Systems (OGMS). In this respect KHD Humboldt Wedag AG developed an improved version of a drum-type magnetic separator called PERMOS® with a special magnetic field configuration for the NdFeB permanent magnets, which gives a magnetic field strength of at least 0.7 Tesla and a wide working zone outside the drum. The magnet system within the PERMOS® unit is no longer made of relatively large magnet blocks of alternating radial magnetisation; the system is now made up of a multitude of small NdFeB bars with a specially oriented magnetisation. This PERMOS® Open Gradient Magnetic Separator can be used for dry magnetic separations in "top-feed" and 'free-fall" feed configuration as well as in the conventional wet "drum-type" feed mode. It allows high throughput rates of up to 40 metric tons of solids per hour and meter of drum length without any clogging problems, even when strongly magnetic com-pounds are present in the feed material. The important design features and the actual machine characteristics of the improved PERMOS® units for dry and wet magnetic separation are described and typical examples for their commercial application for industrial minerals and for martitic iron ores are presented.

Jan 1, 1995

By Terry D. Vandell

The purposes of this presentation are: (1) to discuss the actual as well as potential incidents that have caused and that could cause groundwater contamination at uranium in situ leach mining sites and (2) to discuss remedial actions and solutions that have been or that could be implemented in the future to stop or prevent serious groundwater contamination from in situ leach mining in Wyoming?s Powder River Basin. Open pit, underground, and existing and proposed in situ leach uranium mine sites in the Powder River Basin are shown in Figure 1. In situ leach mining or solution mining for extracting minerals in liquid form is a relatively new addition to the list of conventional mining methods currently used to extract uranium in Wyoming's Powder River Basin. Basically, the in situ leach mining method involves: (1) the injection of a leach solution lixiviant (an acidic or basic oxidizing solution) into a uranium-bearing ore body, via injection wells, to complex the contained uranium, (2) mobilization of the uranium complex from the host material via creation of a soluble complex salt, and (3) surface recovery of the solution bearing the uranium complex via production wells. Uranium is then separated from the leach solution by conventional milling unit operations (ion exchange).

Jan 1, 1981

By W. C. Dailey

The National Steel Pellet Company is owned by National Steel Corporation, managed by the M. A. Hanna Company and located near the town of Keewatin in northern Minnesota. Annually, the concentrator processes 15.24-Mt (15.0 million It) crude taconite with eight 8.2-m diameter by 5.5-m long (27 ft x 18 ft) wet semi-autogenous (SAG) mills to produce 4.57-Mt (4.50 million It) of iron ore pellets. To improve operating costs and primary mill grinding circuit efficiencies, a task force on liners was formed with the operation, maintenance and engineering staff at N.S.P.C. along with the local supplier of mill liners. Results of the task force recommendations since 1980 along with improvements made in the primary circuit operations, are presented. Mill Liner Design and Metallurgy Changes The primary mill liner task force was formed in 1977. Its function was to improve the operating costs and milling efficiencies of the ten 8.2-m x 5.5-m (27 ft x 18 ft) wet SAG mills that were operating at the time. The SAG mills are driven by two 3500 HP motors drawing a total of 5450 kW at 76% of critical speed.

Jan 1, 1985

By Khosrow Badiozamani

Traditionally the mining industry has been lagging in application of computers in their daily or long range plan activities compared to other industries. The question then remains as to how the technology of higher computing capacity for less cost is going to affect the mining industry and how the lukewarm reception of engineers in acceptance of computerized mine planning in the past is going to change because of the new wave of high techology. These questions and the reasons for the lack of usage of computerized mine planning systems by engineers will be evaluated in this paper. In addition, alternatives available to the mining industry will be analyzed and the direction of the future "user friendly" software will be discussed.

Jan 1, 1984

By T. R. A. Davey, J. W. Sherman, B. J. DiSanto, G. Bjorling, G. S. Stacey, J. T. Cullom, R. L. Bird, S. E. Woods, J. C. Blair, Jorma Honkasalo

Most pyrometallurgical processes take place at high temperature with rapid chemical reactions when the elements and compounds are usually liquid or gaseous. Smelting. The classical method of obtaining a metal from its ore or concentrate is to smelt it in a furnace. The initial letter "s" of this word implies that, in addition to the physical process of melting, a chemical change also occurs. This is usually the reduction of metal oxide to metal by carbon or through a series of processes involving oxidation and reduction. Since solid-solid contact would not be sufficient to give a high rate of reaction, most smelting reactions occur by medium of two reactions involving solid-gaseous contact: where M represents a metal. The commonly preferred unit for carrying out these reactions is the blast furnace,1 which is a vertical shaft of refractory brick or water-cooled steel in which lumps of metal oxide and coke are fed at the top, and an air-blast is injected through tuyeres (water-cooled pipes) in the bottom. Molten metal is withdrawn from a pool at the bottom of the furnace, while N2, CO, and CO2 gases leave the top of the furnace, carrying some fine dust or fume with them, which

Jan 1, 1985

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying an atomic force microscope (AFM) and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy to study in situ the adsorption of three different collectors — oleic acid, octanohydroxamic acid (HA) and salicylhydroxamic acid (SHA) — on bastnaesite in aqueous solutions. The results show that all three collectors adsorb on bastnaesite. The hydroxamic acid collectors — HA and SHA — adsorb on bastnaesite mainly in the form of insoluble metal hydroxamate. Their specific adsorption mechanism indicates that high selectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By A. Iordanidis

Fly ash samples were collected from two large lignite-fired power plants of Ptolemais region, northern Greece. Environmental Scanning Electron Microscopy (ESEM) was applied for the characterisation of the samples. ESEM coupled with Energy Dispersive System (EDS) provided fast and accurate results on the morphology, mineralogy and chemical composition of the fly ash particles. Fly ash consists mainly of aluminosilicate glass, silicates, oxides-hydroxides, sulphates, carbonates and char. Various types of chars, spheres (e.g. ferrospheres, cenosphers, plerospheres etc.), spheroids, agglomerates and mineral crystalls were observed. The size distribution of the fly ash particles was correlated with their mineralogical and chemical composition. Possible environmental impacts and potential utilization is also discussed in this study.

Jan 1, 2005

By J. J. Kellar

Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available which allow direct in-situ analysis of adsorbed layers. Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IRJIRS) with reactive internal reflection elements allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in-situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar, 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Figure 1 is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/ dodecyl sulfate, CaCO3/oleate, ZnS/xanthate, and KCl/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990).

Jan 1, 1992

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By B. Alegria

The depressing effects of different inorganic chemicals on the flotation of pyrite have been investigated in this study. The results of the flotation tests indicate that pyrite can be depressed by oxidizing as well as reducing agents under controlled conditions of pH and reagent dosage. Oxidizing reagents such as potassium chromate and potassium dichromate were found to cause complete depression of pyrite in the acidic pH range. These effects are similar to those obtained in the pyrite-cyanide system. A less stable oxidant, potassium permanganate, inhibited the flotation of pyrite at a concentration as low as 0.1 mol/L at all pH values, Addition of reducing chemicals such as ferrous chloride or manganous sulphate to the flotation of pyrite were found to produce depressing effects depending on the additive concentration and pH of the solution.

Jan 1, 1982

By J. M. Link

A technique is presented for the economic selection of a slurry pipeline with the aid of a computer. Mathematical models for the flows of homogeneous slurries are utilized. Only the pipeline and its prime movers are considered. Slurry flow properties are first obtained from rheology and/or pipeline data measurements. A rheological model is then selected for the slurry. It must be emphasized that the accuracy of the method is greatly affected by the accuracy of the slurry flow-property data. Approximate cost parameters may be selected from data for plain and lined pipes, centrifugal and positive displacement pumps, motors and engines. Cost data for the purchase, operation and maintenance of slurry pipelines are also described. A total cost equation for the ownership and operation of a slurry pipeline system is then established. The complexity of the equation is a function of the rheological model selected to describe the slurry. The equation is solved with the aid of a computer for several combinations of pipeline diameters and throughputs to yield minimum total annual cost for the system. A mean velocity is then computed to give the required throughput. The velocity is constrained by an upper and lower bound. A high velocity is undesirable from an energy consumption viewpoint and if pipeline wear is possible. On the other hand, the velocity must exceed the deposition velocity for a heterogeneous suspension or the critical velocity for a homogeneous suspension. There is no guarantee that the velocity developed by this method will lie within the constraints applied, nor that the constraints are even known. This is particularly true for heterogeneous slurries. An important feature of the method is the ease with which the variables can be adjusted to measure the sensitivity of the total cost to the variables. The purpose of the sensitivity analysis is to identify those critical variables that. if changed, can considerably affect the total cost. Mathematically, individual variables are changed and the effect of such a change on the annual total cost is computed. But from a designer's point of view, individual components in the system are changed to study their effect on the annual total cost. A change in one component of the system may involve a change in one or more variables. For example, the replacement of a steel pipe by a smooth-lined pipe will change the pipewall roughness and wall thickness as well as purchase, operating, and maintenance costs.

Jan 1, 1974

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By Owen Kingman

This paper discusses grade control of ore mined at Tennessee Copper Company. Mineral zoning and the influence of mineral zoning on production grade are discussed and illustrated. In order to make this most understandable we will first briefly examine the flow sheet at Tennessee Copper to indicate the path followed by the raw material toward its various products. Then we will discuss some of the characteristics of the ore, specifically the distribution or zoning of the minerals in the ore which cause some of the grade control problems. Finally we Will discuss same of the steps that are taken to combat these problems. The flow sheet is illustrated as plate 1. The mined ore is allied to obtain 3 usable products: Copper concentrate, iron concentrate and zinc concentrate. Copper is found in the mineral chalcopyrite, CuFeS2. The Copper concentrate from the mill contains about 20% copper. These concentrates are smelter in reverberatory furnace and Pierce-Smith converter to blister copper containing 99.2% copper. Some metal is cast into 360 lb. pigs and shipped to the refinery. Some is made into shot copper and used locally to make copper sulfate. Copper sulfate is marketed from Copperhill principally in fungicides.

Jan 1, 1960

By John A. Dearinger, Fred D. Wright, Robert C. Howell

INTRODUCTION The rock mechanics study of the shortwall mining system at Beth-Elkhorn corporation's Hendrix No. 22 Mine is being conducted under contract with the U.S. Bureau of Mines. The objective of the study is to obtain data on surface subsidence over a portion of the mined area, strata subsidence in the mined area, and underground stress changes and displacements in and near natural support elements of the mining system. This study is currently in progress, and only a portion of the results are being presented at this time. The Hendrix No. 22 Mine is located in the moderately rough mountainous terrain of Letcher County in eastern Kentucky. The nearest mine workings to the shortwall area are approximately 1,900 feet distant. The depth of cover over the mined shortwall area varies from 770 feet at Panel 1 to 170 feet at Panel 5 (Figure 1). The strata in the shortwall area is summarized in the three core logs shown in Figure 2. Hole no. 2 is located in approximately the center of the mined shortwall area (Panel 3, Line C, Figure 1). The coal seam in the shortwall area is approximately 4 feet thick and horizontal, although one major ‘roll’ intersects all panels.

Jan 1, 1977

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By Robert J. M. Miller

Thank you Mr. Chairman. For more than 15 years a debate has been taking place among students of massive sulphide deposits as to the origin of these deposits. Prior that time it was widely accepted that the deposits were of hydrothermal, epigenetic and even replacement origin (Wilson, 14). Kinkel, Knight, Stanton and others advanced hypotheses which would explain the, formation of the deposits by different, largely syngenetic, volcanogeric processes. I was fortunate in having become involved in exploration for these deposits at about the time the debate was beginning and thus had an opportunity to apply with some success, some of the new and old ideas for formation of massive sulphide deposits. The deposits which I will discuss today are all located n northwestern Quebec, in the Abitibi orogenic belt. Mattagami Lake Mines is about 100 miles due south and Noranda's Horne Mine about 200 miles south of James Bay. In 1959 I prepared a talk which was presented to the 1960 CIM Convention calling attention to the spatial and possible genetic relationship between the ore sulphides of the Mattagami Area, Quebec and the tuffite, as well as the structures which controlled the ore. In this present paper I would like to cover the following points: (1) The general criteria used by the epigeneticists to support their contention that the deposits were formed after the enclosing rocks.

Jan 1, 1973

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let's also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968