Search Documents

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By Jupneek Singh, Zachary A. Kiehl, Leila Safazadeh, Gareth Kennedy, Eleonora Widzyk-Capehart, Jeremy W. Ward

Mine workers are continuously exposed to a host of nonfatal stressors and potentially fatal hazards: noise exposure, excessive vibration, poor air quality, toxicant exposure, ignition of combustible gases, equipment-related accidents, and thermal heat stress. Wearable or portable sensors and contextual analytics provide a platform to unobtrusively collect and fuse multimodal health and safety data in real time to compute both acute safety and longitudinal health insights. This paper presents preliminary trial results, conducted by Simtars, VigiLife, Inc., and Queensland Mines Rescue Service, of the application of wearable sensors to monitor heat stress and other vital biometrics for mines rescue personnel.

Feb 1, 2024

By A. A. Sadegh

A laboratory investigation was carried out on the characterization and beneficiation of sillimanite ore. Petrographic analysis indicated that the ore consisted of massive elongated sillimanite grains in a matrix of hematite, garnet, feldspar and silica. A procedure for estimating the percentage of sillimanite was developed using float-sink and magnetic-separation techniques. A liberation study was carried out to determine the level of size reduction required to achieve sufficient liberation while ensuring that gravity concentration techniques would be applicable. Laboratory testing was performed on the liberated ore to investigate the applicability of using wide-angle dense-medium cycloning to upgrade this ore. Initially, medium-only tests were carried out using various size distributions of magnetite and ferrosilicon as the dense-medium solids to evaluate the effects of operating conditions on medium segregation. Depending on the medium solids and operating conditions, either positive of negative differentials (difference between the relative densities of the underflow and overflow streams) were obtained. Based on these results, separation tests were performed to process nominal -1.2-mm sillimanite ore. The results indicated that sillimanite concentration could be obtained using a medium relative density that was much lower than would typically be used in a dense-medium cyclone separation.

Jan 1, 2007

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By Amar Prakash, V. M. S. R. Murthy, Ajoy Kumar Singh, Avinash Paul, John Loui Porathur

Weak, layered, and fragile rock mass formation, if not supported properly, is subject to roof failure thereby affecting safety and productivity in underground coal mines. Though Central Mining Research Institute – Indian School of Mines Rock Mass Rating (CMRI-ISM RMR) based well-defined support design guidelines are established, still occurrence of roof failures in underground coal mines is a real matter of concern for mining engineers and researchers. Numerical modeling techniques are successfully used by several researchers by simulating rock mass condition for stability assessment of mine openings. The analysis becomes crucial in case of weak and fragile rock formation. The present research envelops the determination of 31 cases of rock load by CMRI-ISM RMR under different geo-mining conditions followed by the development of modified Rock Mass Rating (RMR), i.e., rock mass rating dynamic ( RMRdyn) by incorporating P-wave velocity as a new parameter. The rock load determined using RMRdyn and numerical models was correlated and found in close agreement. In addition, the deviation in rock load determined by all the three approaches, i.e., CMRI-ISM RMR, numerical modeling, and RMRdyn, was compared with the actual field data. The percentage deviation obtained in RMRdyn and numerical modeling is less compared to CMRI-ISM RMR.

Sep 1, 2023

By S. Norman Kesten

The Galena mine is located astride the Polaris fault in the Coeur d'Alene district of northern Idaho. The surface installations are about a mile up Lake Gulch, the mouth of which is about 2.4 km (1 112 miles) west of the old town of Wallace. The mine had its beginnings when the first claims were located in the early boom days of the district in the 1880s and when the first underground ore bodies were opened up in 1917. During the ensuing 14 years, ore was mined from which were recovered 5.4 Mkg (12 million lb) of lead and almost 14.2 Mg (112 million oz) of silver. Workings consisted principally of a vertical shaft from surface to the 800 level and an offset underground shaft to the 1600 level, together with extensive lateral openings. High-grade silver-copper ore was discovered near the Silver Standard fault in the Sunshine mine, a few miles to the west, on the 1700 level in 1930. By 1937, the Sunshine and adjacent mines were producing silver-copper ore on a regular basis. In 1943 additional ore of a similar type was found along the Chester fault, to the east of the principal Sunshine workings. The interest of American Smelting and Refining Co. (renamed ASARCO in 1975) was aroused and the company's geologists determined that the Galena mine, idle since 1931, provided a geological environment in which similar ore might be found. After negotiations were initiated with the owners of the property, Callahan Zinc-Lead Co., the property in question was deeded to Callahan's wholly owned subsidiary, Vulcan Silver-Lead.

Jan 1, 1990

By S. S. Wang

Dialkyldithiophosphinates are a new class of flotation collectors for base metal sulfide ores. Structurally, they are quite different from the conventional collectors such as mercaptans, xanthates, thionocarbamates and dithiophosphates. Collectors Structures [Mercaptans R-SHS Xanthates R-OCS-M+ Thionocarbamates R-OCNH-R Dithiophosphates 2 R-CCNH-R' Dithiophosphinates (R) 2-PS-M+ ] In the above structural formula, R and R' stand for a hydrocarbon radical, and M+ is an alkali metal or ammonium cation.

Jan 1, 1982

By P. Somasundaran, J. T. Kunjappu

Spectroscopic techniques are becoming increasingly popular for characterizing the interior of adsorbed layers of surfactants and polymers at solid- liquid interface as well as in the identification of com- pounds on mineral surfaces. This review encompasses the application of fluorescence and ESR spectroscopic techniques to reveal the microscopic environment of the adsorbed layers of surfactants and polymers on minerals with a special reference to the adsorption of anionic surfactants (e.g., sodium dodecyl sulfate) and polyelectrolytes (e.g., polyacrylic acid) at positively charged mineral (e.g., alumina) - water interfaces. Finally, the utility of XPS and auger techniques to identify the surface elemental composition of different mineral species has been related to their flotation efficiency.

Jan 1, 1987

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By Gary Jobson

The Mt Todd Gold mine is situated near Katherine in the Northern Territory of Australia. Commissioning of an 8 Mtpa processing facility incorporating a four stage crushing circuit, ball mills, flotation, concentrate regrinding, high rate thickening and CIL processing was commenced during late 1996. A 4.5 M tonne /annum crushing and heap leach facility was commissioned during late 1994, and was subsequently upgraded to a nominal 6 M tonne / annum circuit during 1995. Processing equipment used included primary gyratory, secondary cone and tertiary Barmac VSI crushers. Some of the features of that crushing circuit and heap leach facility were presented at the Randol Perth 95 conference by myself. The location is described as sub tropical with average climatic conditions including 1100 millimetres annual rainfall, predominantly during the December. to March wet season, and 3000 millimetres evaporation and maximum temperatures ranging from around 26 to 46 °C. The main gold occurrence at the Mt Todd site is the Batman deposit, with current published Reserves of some 60 Mt@ 1.20 g Au / tonne ( 0.0425 oz Au / ton ). The primary ore from the Batman deposit is an extremely competent greywacke and is very hard at an average Bond Ball Mill Work Index of26.5 kWhrs/ tonne. Other indicators include a Bond Impact Crush Work Index of 20 kWhrs I tonne, an Abrasion Index of 0.15 and Ultimate Compressive Strength values of 100 - 200 MPa. The main gold occurrence is very finely disseminated free gold (at an average grain size of around 5 micron) within a combination of quartz and mixed sulphide. This gold bearing component is confined to largely parallel veins ranging from 0.5 to 25mm wide within a greywacke matrix. Although the gold is essentially non­refractory, there is a strong recovery versus grindsize relationship due mainly to the liberation characteristics and the relatively low permeability of the host greywacke rock.

Jan 1, 1997

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024

By William C. Peters

The Alpine-Himalayan system, the only major active tectonic belt mainly exposed in a continental mass, is of increasing interest to exploration geologists as well as to theoreticians. Answers to the broader problems of plate tectonics are being sought in this intricate system where the geosynclinal concept was born and where the geotectonic cycle was first applied to metallogeny. The search is all the more intense because it involves scientists from more than a dozen countries with a stimulating variety in perspective. The international Geodynamics Project has allocated the Alpine-Himalayan system to two separate study groups with one directing its attention to the Alpine-Mediterranean region and the other giving consideration to the Himalayan region. This geographic division is accepted in this paper, with remarks being confined to the former and to the west of boundary zone between the European-Asian and the Southeast Asian plates as envisioned by Dewey and Bird (1970). The region is well-mapped in some parts and it includes some of the most intensely-studied geology, most classic mines, and newest orebody discoveries. Within the region, an Alpine-age copper-molybdenum metallogenic belt extends from Rumania to Pakistan. The belt can be considered in terms of plate tectonics, and there is the possibility of using plate tectonics concepts in exploration.

Jan 1, 1973

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By V. L. Franzen, Z. J. Hladysz, C. A. Kliche

The Wharf Resources mine, located in the Bald Mountain Mining District approximately 6.4 km (4miles) west of Lead, South Dakota, has operated a surface gold and silver mine and heap leaching processing facility since 1983. Wharf Resources intends to mine and process gold and silver ore from the Wharf Expansion area which is located on the eastern flank of the currently permitted Foley Ridge Mine. The Trojan Pit for the Wharf Expansion area was initially designed with an overall highwall slope angle of 45o. During mine permit presubmission meetings with personnel from the SD Department of Environment and Natural Resources (SD DENR), the question arose as to whether a detailed slope stability analysis of the proposed Trojan Pit highwalls was completed to justify the 45o slope. Wharf’s response was that the highwall design was based, in part, upon studies completed in1987 on the Annie Creek and Foley Ridge Mines; and, in part, upon subsequent slope stability analyses conducted by Wharf mine personnel through 1996. It was suggested by the SD DENR that the stability study be updated to reflect structural geological conditions in the Wharf Expansion area.

Jan 1, 2000

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By André Vervoort

After the systematic closure of Europe’s coalfields in the late twentieth century, the emphasis is now clearly on industry’s environmental legacy. One aspect of the latter is the longterm surface movement above abandoned coal mines. The analysis of satellite data shows that the subsidence lasts longer than generally assumed. However, a few years after the flooding of the abandoned underground coal mines, a new phenomenon was observed, i.e., the direction of the surface movement was reversed. The phase of upsidence has already lasted for several decades, and only future measurements will tell how long it continues. A key conclusion is that the regions with maximum subsidence do not necessarily correspond to the greatest upsidence. In other words, buildings and infrastructure are subjected to a different loading from this upsidence than during the subsidence phase. The longterm surface movements have an impact on vulnerable structures in the densely populated regions of the former deep coal mining areas in Europe. These movements create additional damage. This new knowledge is also relevant for mines that are still in operation or future mines that are planned.

Feb 1, 2024

By Malte J. M. Gurgel, Axel Preusse

Recent three-dimensional surveying techniques have opened up new opportunities for the registration and monitoring of underground cavities. There are essentially two main methods available: Laser scanning, which is used both above surface and increasingly underground, and photogrammetry, which is also experiencing a renaissance with techniques like structure from motion through the algorithm-based orientation of high-resolution images. Both methods provide the capability to reconstruct reality by various 3-D products like points clouds and meshed models. However, they differ significantly in the steps of registration and calculation as well as in the resulting evaluation options.