Search Documents

By E. R. Pantos

US coal production increased 3% to a record 832 Mt (917 million st) in 1987, according to preliminary Energy Information Administration (EIA) data. Most of the increase was due to the unusually warm summer and the increased coal-fired electricity demand for air conditioning. Drought conditions in the Northwest lowered hydroelectric generation, contributing to the higher use of coal by electric utilities. However, excess production capacity and increased competition from natural gas added further downward pressure on delivered coal prices, continuing the declining price trend of the last several years. Coal production by region Appalachian coal production reached 402 Mt (443 million st) in 1987. This is about 3% more than in 1986 and just short of its 1984 peak. Virginia produced 7% more than its 1986 level, due to increased coal-based electricity demand. Smaller percentage increases were attained in eastern Kentucky, Pennsylvania, and West Virginia. Ohio and Alabama were the only major coal-producing states in Appalachia that produced less coal in 1987 than in the previous year. In the Interior region, 1987 coal production reached a record 182 Mt (201 million st), about 2% above 1986. Illinois is the largest coal-producing state in that region. Production there fell about 3.7%, primarily because of lowered demand at electric utility plants in Alabama and Tennessee. However, this was more than offset by production increases in western Kentucky, Texas, and Indiana. After falling slightly in 1986, coal production in the West resumed its upward trend to a record 248 Mt (273 million st). Wyoming is that region's dominant coal producer. It mined 7% more coal than in 1986. Wyoming's increase offset the 11% decline in New Mexico production and smaller declines in other Western states. Coal consumption and prices Domestic coal consumption reached a record 759 Mt (837 million st) in 1987. Most of the increase resulted from the unusually warm summer that led to higher than normal peak demands for electricity in the third quarter. Electric utility coal consumption was also boosted by the below-normal hydroelectric generation that resulted from low water levels in the Northwest. These factors more than offset the effects of increased nuclear power generation and competition from natural gas. As a result, coal provided 56.9% of electric utility generation in 1987, compared with 55.7% in 1986. Electric utilities consumed a record 651 Mt (718 million st) of coal. While electric utility coal consumption increased, the average cost of coal to utilities was down, from $1.58 per million Btu in 1986 to $1.52 in 1987. The average price of coal delivered to utilities in 1987 was $35.09/t ($31.84 per st), the lowest since 1981. Coal prices were held down by a glut of coal supplies and by a decline in the average price of natural gas to electric utilities. Coal consumption at coke plants in 1987 was 2.6% above the 1986's 32.5 Mt (36 million st). This increase reflects steel's recent resurgence. Coking coal demand, though, was reduced by the increased use of continuous casting and electric furnace technologies. The average price of coal delivered to coke plants fell from $56.02 to $51.35/t ($50.83 to $46.59 per st). Coal consumption in the industries other than coke plants amounted to 68.2 Mt (75.2 million st) in 1987, slightly less than in 1986. Coal lost part of its market share to natural gas, which was priced favorably relative to coal. The average price of coal delivered to manufacturing plants was at its lowest level of the current decade. It fell from $39.50/t in 1986 to $37.27/t ($35.84 to $33.81 per st). Residential and commercial coal consumption fell to 6.2 Mt (6.9 million st) that is 9.8% below 1986 and the lowest since 1980. This decline is also attributed to the relatively low price of natural gas in 1987. Coal stocks Coal consumers held 169 Mt (186 million st) of coal stocks at the end of 1987, 5.9% above the 1986 year-end level. Most of this increase was due to stockpiling by electric utilities in anticipation of a possible strike by the United Mine Workers of America early in 1988. Stocks at electric utilities increased to an estimated 154 Mt (171 million st) at the end of 1987, 5.6% higher than the previous year. This was much lower than 1984's stock buildup. Coke plants increased their coal stocks by 30% in 1987 to 3.5 Mt (3.9 million st), rebounding from the unusually low inventories of 1985 and 1986. Other industries increased their stocks slightly in 1987. Coal producers and distributors ended 1987 with 25 Mt (28 million

Jan 5, 1988

By G. S. Austin

New Mexico produced 83% of domestic potash and 27% of domestic consumption in 1992. The potash industry of New Mexico produces sylvite (KCI), langbeinite (K2SO4-2Mg(SO4)2), and artificial K2SO4. Average sylvite grade in New Mexico today is about 14%. The average grade of langbeinite is 8-10% Kp. Commercial potash occurs in the middle or McNutt Member of the Salado Formation (Upper Permian Ochoan Series). The 120-m-thick McNutt Member dips about 1° east and contains 11 of 12 potential ore zones in the Salado. The mineralogy and proportion of clay minerals, up to 7% of the ore, influence optimum milling procedures and ore grade cutoff.

Jan 1, 1994

By J. Gustavson, E. Mallard, F. Pirkle

The Sales Comparison Approach to estimating the value of a mineral property must always be attempted1 . In addition to other parameters, the approach depends heavily on the availability of transaction data. The consideration for the mineral property must be in form of cash, cash equivalent or other consideration. In other words, “What dollar amount did the property sell for?” Mineral properties are generally real estate, albeit frequently buried deeply under the overlying surface real estate, unless the property may be a quarry. In some states, transactions must be recorded in county courthouses, and the sale consideration must be included. In such cases, the appraiser’s job is made easy. In other locations, the sale considerations are withheld in the courthouse data; but occasionally a local transfer tax is collected and recorded. Again, the appraiser’s job is made easy by back calculation with knowledge of the legislated transfer tax percentage. The worst problem occurs when the consideration for a mineral real estate sale is totally withheld. That may occur in so-called nondisclosure states. A recent map2 of ten non-disclosure states in red is shown below. For the full color code, please refer to the footnote

Mar 2, 2022

By Juan J. Monsalve, Mario Karfakis, AMAN SONI, Nino Ripepi, Jim Hazzard

Pillar collapses are events that due to their severe consequences can be classified as high risk. The design of pillars in underground room-and-pillar operations should migrate to risk-based design approaches. The authors of this work proposed a risk-based pillar design methodology that integrates stochastic discrete element modeling for pillar strength estimation, and stochastic finite volume modeling (FVM) for stress estimation. This paper focuses on the stochastic FVM component for stress estimation. The mining and geomechanical aspects of a case study mine (CSM) are described and pillar stresses are estimated by using three approaches: (1) analytical solutions, (2) 2D finite element modeling, and (3) 3D finite volume modeling. This operation extracts a 30° dipping deposit, which makes current underground stone mine design guidelines inapplicable for this CSM. This work compares results from each stress estimation approach and discusses uses the point estimate method as a simplified stochastic approach to evaluate the effect of rock mass elastic properties variability on pillar stress distribution. Results from this work show that the three estimation approaches lead to different estimations, possibly, due to the wide range of assumptions each estimation approach considers. It was also determined that the horizontal to vertical stress ratio has a significant impact on pillar stress magnitude. Therefore, it is recommended to perform in situ stress measurements, or assume worst-case-scenario values to account and reduce uncertainty due to this parameter. The stochastic stress estimation approach used in this paper provides results that can integrate a risk-based pillar design framework.

Sep 24, 2022

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

By I. Demers

Doyon mine, Quebec, Canada evaluates the possibility of desulphurizing their tailings to produce material to be used in as cover over the acid generating tailings disposal site. Laboratory tests were conducted and showed that a single-layer cover made of desulphurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modelling with the software Vadose/W was undertaken to optimize the design parameters, namely cover thickness, water table position, and residual sulphide content of desulphurized tailings following laboratory work. It was found that the optimal configuration includes a 1 m desulphurized tailings cover containing 0.8%S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux towards acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective chosen for Doyon mine (10 mol/m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2008

By E. K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. While providing a useful tool for the investigation of mine planning problems, the availability of graphic output was limited or non-existent. Computer graphics is a natural extension of mine simulation methods and provides a more dramatic level of understanding and interface with an engineer. With today's high cost of venture development, the need for an easy to use but complete systems model which includes the major elements of mine planning with an interactive graphics interface has never been more apparent. In this paper, the underlying philosophy of design of an interactive interface to a complete surface mining simulation model is described. The basic structures of the surface mining system and the simulation model are discussed. The methods and algorithms used to implement the various subsystems are presented. Practical considerations of the design of displays and user interaction are illustrated, especially as they apply to the application of the package by a mining engineer. A simple example is provided to demonstrate the concepts embodied in the model and to show how a simulation is built from mine data.

Jan 1, 1984

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By M. O?Driscoll

The tide has turned. Developments in China that have continued to unfold over the last four years or so have now reached a point where the supply market dynamics of certain industrial minerals have changed significantly. No more is this sea change better exemplified than by the supply market for magnesite, and in particular, its processed derivative grades of dead burned magnesia (DBM), caustic calcined magnesia (CCM), and fused magnesia (FM). But what has compounded the barrage of influencing factors impacting this sector, which include the widespread effects of energy and freight cost increases, has been rising demand from certain end use markets. Clearly, the magnesia market is experiencing bittersweet conditions. But those western producers which have monitored and responded to this market transformation, stand to taste success in the near and medium future. REVOLUTION IN WORLD SUPPLY STATUS In essence, while China, as host to a wealth of magnesite resources in Liaoning province, remains a huge producer of magnesia, its supply dominance on the global magnesia market has been considerably weakened. In future, it will mainly aim to supply domestic, and to some extent east Asian markets. Magnesia consumers outside China are now scrabbling for alternative, ?western? sources of supply. At the same time, magnesia producers outside China that weathered the storm of low cost Chinese DBM and FM imports flooding their regional markets for the last 20 years (and many did not), are busy investing in production capacity increases to meet not just demand from falling Chinese supply, but also demand from end use markets which is picking up. And it is not just a matter of expanding capacity of existing magnesia product lines. In the face of plentiful lower cost DBM and FM substitutes from China over the last couple of decades, many western magnesia producers started to switch their focus to the non-refractory markets (eg. environmental, specialities) which promised lucrative opportunities (and still do) and crucially, a lessening of sales revenue dependence on the DBM refractories market. Now we have the likes of Baymag (Canada), Bommag (Serbia/Turkey), and Kumas (Turkey) not only expanding capacities but seriously considering diversifying into DBM and FM production. Perhaps DSP (Israel), having ceased its famous high purity DBM activity as recently as 2005, might even reconsider a return to the ?other side?. But it?s not all DBM and FM. The CCM and specialities markets are also demanding a response, and so Baymag, DSP, Martin Marietta (USA), Premier Chemicals (USA), Qmag (Australia), MGR (Spain), and Magnifin (Austria) are also stepping up to the market on the non-refractory side. From most accounts, the situation with regard to Chinese supply has been described as one of turmoil, with prices rising, leading to improving opportunities for western producers. The majors are conducting huge expansion programmes, such as Qmag, Magnezit (Russia), and the new look Magnesita (Brazil). Even smaller players such as Causmag (Australia) and Dalmia (India) are looking to increase production. In short, the western magnesia supply sector is witnessing a landmark event in capacity investment and market share penetration as China?s previously dominant role begins to weaken (for a review of western capacity expansions see Industrial Minerals, September 2008, p.28). MERGER & ACQUISITION ACTIVITY Another response of course has been a raft of mergers and acquisitions in order to secure resources and supply outside China. These have included private equity groups taking over Magnesita and Qmag; Imerys entering the FM business through UCM; Peñoles further consolidating the electrical grade FM market by acquiring Minco; Martin Marietta acquiring Morton Salt?s Specialty Magnesia Group; Bomex entering the market through Calmag (now Bommag); LWB acquiring Magnesita; and Magnezit?s pursuit of Slovakian magnesia, with Slovmag aboard while currently wooing SMZ. Interestingly, RHI has gone ?the other way?, and has invested in a state of the art joint venture operation at Dashiqiao, Liaoning, with which it aims to secure high quality feedstock for its Chinese refractory plants. Tata Refractories Ltd has announced intentions to follow suit, and other majors, such as Qmag are known to be interested in seeking options. Naturally, there is now renewed interest from several parties in the idled 50,000 tpa DBM/10,000 CCM Jormag facility, Jordan, and the commercially undeveloped Zhargat project, Saudi Arabia. Elsewhere, there will no doubt be suitors for stakes in SMZ, in Slovakia, and Magnohrom, in Serbia, whose respective ownerships are on the block. THE ?CHINA FACTOR? The ?China factor? has been key to magnesia?s market change, and has significantly influenced prices and availability of material to global markets. Resources & production China hosts the largest share of the world?s magnesite deposits, accounting for 26% or 3,319m. tonnes of predominantly sparry magnesite (followed by North Korea, 24%, and Russia, 22%; Wilson 2008). China accounts for 44% of total world magnesite mined (19m. tonnes in 2007) and 50% of the total world magnesia produced (8.2m. tonnes CCM, DBM, FM; Wilson 2008). Russia follows China at 13% of magnesia supply, illustrating China?s dominance of magnesia production. Apart from one producer in Shandong province, central eastern China, the country?s magnesite resources and production are concentrated around the cities of Haicheng and Dashiqiao in Liaoning province, north-east China. Although there are also producers in the Xiuyan district of south-east Liaoning, the Haicheng-Dashiqiao Magnesite Belt hosts the majority of producers. In total these may number 200-300 of large,

Jan 1, 2009

By W. D. Bachman

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from Kennecott Copper Corporation's Chino mine. The efficiency with which the various samples could be ground was found to vary over an extremely wide range, even among samples taken from different locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale non-homogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully.

Jan 1, 1970

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By David S. Yang, Osamu Taki

The innovative Soil-Cement Mixing Wall Technique, developed independently in Japan, consists of mixing in-place soils with cement grout using multi-axis augers and mixing paddles to construct overlapping soil-cement columns. The applications of overlapped soil-cement columns include cutoff walls for groundwater control and structural diaphragm walls for excavation support. The special features of this technique include water tightness, versatile strength design, and efficient installation in subsurface materials varying from clayey soils to cobbles or soft rocks. Through the introduction of two recent subway projects in Japan, this paper presents the design parameters, construction procedure, quality control and performance of soil-cement wall for excavation support and groundwater control.

Jan 1, 1989

By E. J. Harvey

The Ozarks has been called "a diamond in the rough". In this region streams have steep gradients, sparkling clear flows of cold water fed by many springs, and a wildness that is almost unique in the central part of the United States today. The Current River and its tributary, Jacks Fork, have been set aside for preservation by the National Park Service as a "Wild River" in the first park of its kind in the country. It is called the Ozark National Scenic Riverway. Similarly, responsibility for the preservation of the Eleven Point River has been assigned to the U. S. Forest Service. Protection of other streams in the Ozarks has been considered by State agencies. The hydrologic system of the Ozarks is a complex network of gaining and losing streams, caves, conduits, and large springs. Increased sewage loads derived from the growing towns and expanding tourist trade are a potential hazard; effluents may flow underground for long distances, polluting springs and wells. To add another dimension to the hydrologic picture a new lead industry is also flourishing in the Ozarks. Although the history of lead mining in the area goes back to 1701 (U. S. G. S., p. 43), the area has not seen a revitalization like the one that has been developing in the last 10 years; and the economic growth promises to continue indefinitely. Although this brings capital expenditures and wages into the area, it also brings potential hydrologic problems. Chemicals, wastes and other substances either stored on the surface or transported across it are subject to accidental spillage. In an area where these substances remain on the surface their effects are subject to surveillance. In the Ozarks, however, this may not be possible.

Jan 1, 1970

By Hans E. Tausig

The economics of transporting minerals by sea in less than full cargo lots encompasses an analysis of production costs, sale and inventory calculations and a careful comparison of ocean freight costs all of which when pieced together will usually definitively indicate which of the ocean freight alternatives is the correct one for the economic factors involved. To illustrate: Let us assume that a production to be marketed yields 60,000 metric tons of copper concentrates over a twelve month period. Shipment is geographically viable through Vancouver, B.C. The production has been sold to a Japanese Smelter and the mine produces at a rate of 5,000 metric tons of concentrates per month. The copper has been sold CIF FO. The Seller has carefully investigated ocean freight rates Vancouver, B.C./Hibi, Japan and finds that he could obtain a twelve month freight contract at $15.00 per metric ton FIGS based on a loading/discharging speed of 4000/ 2000 metric tons per WWDSHEX (weather working day, Sundays and Holidays excluded) this freight rate being predicated on shipping in lots of minimum. 15,000 tons. A further freight investigation reveals that to ship at the same terms and conditions but in lots of 5,000 tons, and shipping each month (in accordance with the mine's actual production) would cost $20.00 per metric ton FIOS. The calculation that is now made is whether it is more desireable to pay a higher ocean freight by shipping in 5,000 ton lots or to pay the lower freight where here the ocean freight involves a difference of some $300,000.00.

Jan 1, 1979

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By Emanuele Catelli, Paolo Vicentini, Manuel Petitat, Paolo Lanfranchi

"More than 800 million tons of material will be excavated during large underground projects such as tunnels, undergrounds and power plants by 2030 in Europe only. The raw material excavated is often classified as waste, which involves environmental impact and transport issues: landfill areas, CO2 emissions and noise. But how can such massive amounts of material be transported, processed and deposited? Using the example of the AlpTransit Ceneri Base Tunnel (15.4 km), we show that suitable excavated materials can be used sustainably as a primary resource for tunnel concrete. This requires careful planning of the installations and storage areas by the client, timely building of the processing plants and other handling facilities outside the tunnel and a continuous evaluation of the raw material quality. 1. INTRODUCTION Spoil management is a central element of large construction projects. The systematic reuse of suitable excavated material not only saves natural resources, reduces transport distances and landfill volume, but can also decrease overall construction costs. Ideally, all of the concrete needed for tunnel lining can be produced with this on-site material. Such a natural resource management concept was applied for the construction of the new Gotthard Base Tunnel (L = 57 km). Spoil management concepts are, how-ever, difficult to implement and call for innovative techniques, sophisticated logistics and organization. In the context of large projects, environmentally friendly transport, processing and storage of millions of tons of excavated loose material represent another logistics challenge (Simmen & Lieb, 2010). This paper shows key factors that led to the successful completion of spoil management at the Ceneri Base Tunnel, which constitutes a part of the AlpTransit Gotthard Project (Figure 1)."

Jan 1, 2016

By H. Kinilakodi

In 2008, the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using a sample of 103 mines with 2008 and 2009 data, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performances as compared to large and medium-sized mines.

Jan 1, 2011

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

By Kenneth R. Krivanek

In recent years the widespread problems of air and water pollution generated by both population and industrial expansion have become a major public concern. Therefore, many municipalities are striving to achieve more efficient wastewater treatment processes so these wastewater's can be reintroduced into the waterways of our nation with little or no detrimental effects on the future beneficial use of that water. With this, improved treatment comes an ever increasing volume of wastewater sludge which must be disposed of in a manner of minimal impact on the environment. Furthermore, with demand for energy continually accelerating in this nation, our concern over high oil prices and our increasing dependency on foreign oil sources, there has been an ever growing interest in the largest energy source that are nation has, coal. However, surface mining of coal can cause many environmental problems when adequate precautions are not faithfully adhered to. These problems include water pollution from silt and/or clay erosion and acid runoff, produced by oxidation and hydrolysis of pyrite; i.e., FeS2 + 3/02 + H20 + FeSO4 + H2SO4. One method of wastewater sludge disposal which can utilize large volumes of sludge for a beneficial project that may not compound our environmental problems is spray irrigation, to either depleted farmland or to abandoned strip-mined soils. Sludge is characteristically high in organics, as well as having near neutral to alkaline pH properties. With these two qualities it possesses a potential for neutralizing acid strip mine spoils, which would enhance the establishment of a vegetative ground cover. Sludge can accomplish this by lowering the oxidation potential, reducing the solubility of iron and aluminum and by the chelation of metals, thereby

Jan 1, 1977

By E. R. Bauer

A primary goal of Ground Control Research, Bureau of Mines, U.S. Department of the Interior, is to develop information that can be used by the mining industry to reduce accidents and fatalities due to failure of mine roof. A specific research objective is to determine methods to detect hazardous coal mine roof. This paper reviews the existing and experimental techniques, and describes a recent Bureau of Mines contract research project that resulted in a simple technique and prototype instrument for evaluating mine roof competence.

Jan 1, 1986